| Commit message (Collapse) | Author | Age | Files | Lines |
|---|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Specify firmware partition format by compatible string.
formats in ramips:
- denx,uimage
- tplink,firmware
- seama
It's unlikely but the firmware splitting might not work any longer for
the following boards, due to a custom header:
- EX2700: two uImage headers
- BR-6478AC-V2: edimax-header
- 3G-6200N: edimax-header
- 3G-6200NL: edimax-header
- BR-6475ND: edimax-header
- TEW-638APB-V2: umedia-header
- RT-N56U: mkrtn56uimg
But it rather looks like the uImage splitter is fine with the extra
header.
The following dts are not touched, due to lack of a compatible string in
the matching firmware splitter submodule:
- CONFIG_MTD_SPLIT_JIMAGE_FW
DWR-116-A1.dts
DWR-118-A2.dts
DWR-512-B.dts
DWR-921-C1.dts
LR-25G001.dts
- CONFIG_MTD_SPLIT_TRX_FW
WCR-1166DS.dts
WSR-1166.dts
- CONFIG_MTD_SPLIT_MINOR_FW
RBM11G.dts
RBM33G.dts
- CONFIG_MTD_SPLIT_LZMA_FW
AR670W.dts
- CONFIG_MTD_SPLIT_WRGG_FW
DAP-1522-A1.dts
Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
|
| |
|
|
|
|
|
| |
The previous offset was invalid and pointed to the end of the partition,
which was causing issues with mt76
Signed-off-by: Felix Fietkau <nbd@nbd.name>
|
| |
|
|
|
|
|
|
|
| |
Use diag.sh version used for other targets supporting different leds
for the different boot states.
The existing led sequences should be the same as before.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
|
|
| |
Starting with kernel 4.4, the use of partitions as direct subnodes of the
mtd device is discouraged and only supported for backward compatiblity
reasons.
Signed-off-by: Alex Maclean <monkeh@monkeh.net>
|
| |
|
|
|
|
| |
Fix individual boards dtc warnings or obvious mistakes.
Signed-off-by: Mathias Kresin <dev@kresin.me>
|
| |
|
|
|
|
| |
Also fix several typos in led node name.
Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
|
| |
|
|
|
|
|
|
|
|
|
| |
According to console log during TP-Link TL-WR840N v5 OEM firmware update
procedure 0x3e0000-0x3f0000 64kB "config" partition, which is used to store
router's configuration settings, is erased and recreated again during every
OEM firmware update procedure, thus does not contain any valuable factory data.
So it is conviniant to use this extra 64kB erase block for jffs overlay due
limited flash size on this device like it used on TP-Link's ar71xx boards.
Signed-off-by: Serg Studzinskii <serguzhg@gmail.com>
|
|
|
TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and
non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC.
Specification:
- MT7628N/N (580 MHz)
- 64 MB of RAM (DDR2)
- 4 MB of FLASH
- 2T2R 2.4 GHz
- 5x 10/100 Mbps Ethernet
- 2x external, non-detachable antennas
- UART (J1) header on PCB (115200 8n1)
- 1x LED (GPIO-controlled), 1x button
* LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't
(fully) supported by gpio-leds driver. This type of LED requires both
GPIOs state change at the same time to select color or turn it off.
For now, we support/use only the green part of the LED.
Orange LED is registered so you can later use it for your own purposes.
Flash instruction:
Unlike TL-WR840N v4 flashing through WEB UI works in v5.
1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image.
2. Go to 192.168.0.1
3. Flash the sysupgrade image through Firmware upgrade section of WEB UI.
4. Wait until green LED stops flashing and use the router.
Notes:
TFTP recovery is broken since TP-Link reused bootloader code for v4 and
that does not take into account only 4 MB of flash and bricks the device.
So do not use TFTP Recovery or you will have to rewrite SPI flash.
They fixed it in later GPL code,but it is unknown which version of
bootloader you have.
After manually compiling and flashing bootloader from GPL sources TFTP
recovery works properly.
Signed-off-by: Robert Marko <robimarko@gmail.com>
|
