aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/TEW-692GR.dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for indicating the boot state using multiple ledsMathias Kresin2018-10-071-1/+4
| | | | | | | | | Use diag.sh version used for other targets supporting different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move partitions into partition table nodeAlex Maclean2018-08-041-23/+27
| | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: fix dtc warningsMathias Kresin2018-08-041-2/+0
| | | | | | Fix individual boards dtc warnings or obvious mistakes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix pci/pcie related dtc warningsMathias Kresin2018-08-041-18/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the ranges property to the PCI bridges where missing. Add the unit address to PCI bridge where missing. Rework the complete rt3883 pci node. Drop the PCI unit nodes from the dtsi. They are not used by any dts file and should be rather in the dts than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the pci interrupt controller out of the pci node. It doesn't share the same reg and therefore should be an independent/SoC child node. Move the pci related rt3883 pinctrl setting to the dtsi instead of defining the very same for each rt3883 board. If the device_type property is used for PCI units, the unit is treated as pci bridge which it isn't. Drop it for PCI units. Reference pci-bridges or the pci node defined in the dtsi instead of recreating the whole node hierarchy. It allows to change the referenced node in the dtsi without the need to touch all dts. Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips are the first device on the bus. The unit address has to be the bus address instead of the PCI vendor/device id. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Use dts alias based status ledChuanhong Guo2018-07-161-1/+5
| | | | | | Also fix several typos in led node name. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: update device tree source filesL. D. Pinney2017-08-031-5/+6
| | | | | | | | Use the GPIO dt-bindings macros and add compatible strings in the ramips device tree source files. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: dts: use keycode defines from input dt-bindingMathias Kresin2016-11-131-2/+4
| | | | | | | | | | | | | | | | | | | | | All compiled device tree files not mentioned are binary identical to the former ones. Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts. Due to the include of the input binding header, the BTN_* node names in: - ramips/GL-MT300A.dts - ramips/GL-MT300N.dts - ramips/GL-MT750.dts - ramips/Timecloud.dts will be changed by the compiler to the numerical equivalent. Move the binding include of lantiq boards to the file where they are used the first time to hint the user where the values do come from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add TEW-691GR/TEW-692GR 2.4 GHz interface mac addressesMathias Kresin2016-11-091-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Assign an unused MAC addresses to the 2.4GHz wifi interface as it was originally planed but not possible. The MAC address numbering of the TEW-691GR changes to the following pattern: LAN: AA:BB:CC:DD:EE:0C WIFI: AA:BB:CC:DD:EE:0D WAN: AA:BB:CC:DD:EE:0F The MAC address numbering of the TEW-692GR changes to the following pattern: LAN: AA:BB:CC:DD:EE:e4 WAN: AA:BB:CC:DD:EE:e5 2.4GHz: AA:BB:CC:DD:EE:e7 5 GHz: AA:BB:CC:DD:EE:e8 Set the label and compatible string for the TEW-692GR PCIe wireless according to the the PCI binding documentation. Use the wifi@0,0 label and the pci0,0 compatible string since the PCI vendor and device id is unknown. It should work anyway since the compatible string isn't evaluated (yet). Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: TEW-692GR: fix switch and wirelessMathias Kresin2016-08-201-1/+22
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The AR8327 initvals were not copied to the DTS during the switch from mach file to device tree and broke the switch on the device. The former used PORT6 related initvals were wrong and have been corrected. The phy mode setting for the switch was missing in the DTS as well. The wireless requires an eeprom to work. The dual band wireless chips have both bands enabled by default but only one band per chip is working. The stock firmware uses the following mac addresses: LAN: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 5 GHz: AA:BB:CC:DD:EE:E8 Assuming the mac address range :E4 to :E8 is reserved for this device, the MAC addresses were reorder to have a unique MAC address for each interface: LAN: AA:BB:CC:DD:EE:E4 2.4GHz: AA:BB:CC:DD:EE:E4 WAN: AA:BB:CC:DD:EE:E5 5 GHz: AA:BB:CC:DD:EE:E8 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: DTS reworkStanislav Galabov2016-05-121-56/+54
| | | | | | | | Add node aliases to dtsi files. Reword dts files so they're more in-line with upstream. Fix some more warnings and errors reported by dtc Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
* ramips: Change all '/include/' clauses to '#include' so preprocessing canStanislav Galabov2016-05-101-1/+1
| | | | | | be done properly for the entire device trees. Signed-off-by: Stanislav Galabov <sgalabov@gmail.com>
* ramips: use consistent naming scheme for LEDsJohn Crispin2015-08-171-2/+2
| | | | | | | | | | | | | The upstream LED naming convention is "device:color:led-name", but it seems that many of supported boards in OpenWrt don't follow this approach. The following patch fixes this inconsistency in dts{,i} files and updates base-files scripts for ramips target: * fixes wrong indentation * keeps case statements structure in same convention as in other scripts (no empty line after ";;", no indentation for case...esac body) * fixes wrong LED names for some of boards (makes them the same as in dts{,i} files) * combines boards with same configuration (ex. set_wifi_led "rt2800pci-phy0::radio" in 01_leds) Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46664
* ramips: fix indentation and other mistakes in .dts{, i} filesJohn Crispin2015-08-171-2/+7
| | | | | | | | | | | | | | | | | | | | The following patch fixes: * wrong indentations * doubled gpio-keys-polled nodes (DIR-300-B7, DIR-320-B1, DIR-610-A1) * duplicate spacings * empty lines at end of files and after last child nodes * trailing and leading whitespace * unnecessary and commented-out code * missing empty lines between nodes and between properties and nodes * unnecessary empty lines between nodes properties [1] in .dts{,i} files, for ramips target. [1] Some of empty lines in SOCs dtsi files were left untouched, because they seem to be there for a reason (readability?). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> SVN-Revision: 46613
* ralink: add missing OF nodeJohn Crispin2014-03-181-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 39950
* ralink: set the mac addr via the dts fileJohn Crispin2013-11-251-0/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38902
* ralink: add pinctrl driverJohn Crispin2013-09-171-16/+17
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38026
* ralink: update patchesJohn Crispin2013-06-231-2/+11
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37016
* move memory detect node to dtsi filesJohn Crispin2013-04-091-4/+0
| | | | | | Signed-of-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36290
* ramips: TEW-692GR.dts fixesGabor Juhos2013-04-081-15/+45
| | | | | | | | | | | * fix pinmux settings * remove spi node * add PCI node * add nor-flash node Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36268
* ramips: remove top-level {address,size}-cells properties from .dts filesGabor Juhos2013-04-071-2/+0
| | | | | | | | Those are defined in the SoC specific .dtsi files. Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 36237
* fix typo pinmmux -> pinmuxJohn Crispin2013-04-061-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36216
* add the dts files that describe the boards in futureJohn Crispin2013-04-031-0/+88
Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36168
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 19:54:40 +0000