aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/dts/R6220.dts
Commit message (Collapse)AuthorAgeFilesLines
* ramips: add support for indicating the boot state using multiple ledsMathias Kresin2018-10-071-1/+4
| | | | | | | | | Use diag.sh version used for other targets supporting different leds for the different boot states. The existing led sequences should be the same as before. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: set usb led trigger via devicetreeMathias Kresin2018-10-071-0/+2
| | | | | | | | | | Assign the usbdev trigger via devicetree for all subtargets and drop the userspace handling of the usb leds. With the change all usb ports are triggering the usb led instead of only usb 1.1 XOR usb 2.0 XOR usb 3.0 as it was before. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: move partitions into partition table nodeAlex Maclean2018-08-041-27/+33
| | | | | | | | Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* ramips: fix dtc warningsMathias Kresin2018-08-041-2/+0
| | | | | | Fix individual boards dtc warnings or obvious mistakes. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix pci/pcie related dtc warningsMathias Kresin2018-08-041-14/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Add the ranges property to the PCI bridges where missing. Add the unit address to PCI bridge where missing. Rework the complete rt3883 pci node. Drop the PCI unit nodes from the dtsi. They are not used by any dts file and should be rather in the dts than in the SoC dtsi. Express the PCI-PCI bridge in a clean devicetree syntax. The ralink,pci-slot isn't used by any driver, drop it. Move the pci interrupt controller out of the pci node. It doesn't share the same reg and therefore should be an independent/SoC child node. Move the pci related rt3883 pinctrl setting to the dtsi instead of defining the very same for each rt3883 board. If the device_type property is used for PCI units, the unit is treated as pci bridge which it isn't. Drop it for PCI units. Reference pci-bridges or the pci node defined in the dtsi instead of recreating the whole node hierarchy. It allows to change the referenced node in the dtsi without the need to touch all dts. Fix the PCI(e) wireless unit addresses. All our PCI(e) wireless chips are the first device on the bus. The unit address has to be the bus address instead of the PCI vendor/device id. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Use dts alias based status ledChuanhong Guo2018-07-161-1/+5
| | | | | | Also fix several typos in led node name. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* Revert "ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928"John Crispin2018-06-011-0/+4
| | | | | | This reverts commit 02f815d1907cdd7e042415a2b4a749c819087168. Signed-off-by: John Crispin <john@phrozen.org>
* ramips: Fix WiFi after 5f7396ebef09b224edf08b0bda113613a42f0928Rosen Penev2018-05-301-4/+0
| | | | | | | | | | | | | That commit exposed a bug in the DTS files used by mt7621 where the wrong reg value for pcie1 (and potentially pcie2) was being used. This was causing WiFi failures for interfaces in pcie1. eg. 2.4GHz working but not 5GHz. As all of these dts entries are already specified in mt7621.dtsi, remove them. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: fix polarity in gpio-export nodeMathias Kresin2017-12-181-1/+1
| | | | | | | | If we need to set the initial output value to GPIOF_OUT_INIT_HIGH (1) to enable something, the pin is ACTIVE_HIGH. The same applies to GPIOF_OUT_INIT_LOW (0) and ACTIVE_LOW. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: mt7621: add compatible stringsL. D. Pinney2017-07-291-0/+1
| | | | | | | Add compatible strings to all mt7621 based device tree source files to fix formal issues. Signed-off-by: L. D. Pinney <ldpinney@gmail.com>
* ramips: let the "reserved" MTD partition be RO for R6220Enrico Mioso2017-05-311-0/+1
| | | | | | | | | | The "reserved" partition should probably be read-only, just in case. Even not knowing it's content, other devices have marked it as such, so it seems a good idea to do so also for this device. Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> CC: Mathias Kresin <dev@kresin.me> CC: Hanqing Wong <hquu@outlook.com>
* ramips: add support for Netgear R6220Hanqing Wong2017-03-121-0/+156
This patch adds support for the Netgear R6220, aka Netgear AC1200 and R6220-100NAS. Specification: - SoC: MediaTek MT7621ST (880 MHz) - Falsh: 128 MiB (Macronix MX30LF1G08AA-TI) - RAM: 128 MiB (Nanya NT5CB64M16FP-DH) - Wireless: MediaTek MT7603EN b/g/n , MediaTek MT7612EN an+ac - LAN speed: 10/100/1000 - LAN ports: 4 - WAN speed: 10/100/1000 - WAN ports: 1 - Serial baud rate of Bootloader and factory firmware: 57600 Installation through telnet: - Copy kernel.bin and rootfs.bin to a USB flash disk, plug to usb port on the router. - Enable telnet with link: http://192.168.1.1/setup.cgi?todo=debug (login if required, default: admin password) - You will see "Debug Enabled!" - Telnet 192.168.1.1 and login with "root" - ls /mnt/shares/ to find out path of your USB disk. 'myUdisk' for example. - cd /mnt/shares/myUdisk - mtd_write write rootfs.bin Rootfs - mtd_write write kernel.bin Kernel - reboot nmrpflash can be used to recover to the netgear firmware if a broken image was flashed. Signed-off-by: Hanqing Wong <hquu@outlook.com>