aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ramips: enable power LED and second uart on GL-MT300N-V2Benjamin Valentin2018-02-231-1/+1
| | | | | | | | | The device has a second uart accessible via pin headers, so enable it. There is also a green power led which was not enabled previously. Enable it too and use it as status LED. Signed-off-by: Benjamin Valentin <benjamin.valentin@volatiles.de>
* ramips: add support for ALFA Network AWUSFREE1Piotr Dymacz2018-02-224-20/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AWUSFREE1 is an USB Wi-Fi N300 adapter based on MT7628. Specification: - MT7628AN (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH (SPI NOR) - 2T2R 2.4 GHz (MT7628) with external FEM (RFFM4203) - 2x detachable antennas (RP-SMA) - ASIX AX88772 USB to Ethernet bridge (connected with MT7628 PHY0) - 4x LED (2 driven by GPIO) - 1x button (reset) - 1x mini USB for host and main power input - UART header on PCB Flash instruction: You can use sysupgrade image directly in vendor firmware which is based on LEDE/OpenWrt. Alternatively, you can use web recovery mode in U-Boot: 1. Power device with reset button pressed and release it after ~5 sec. 2. Setup static IP 192.168.1.2/4 on your PC. 3. Go to 192.168.1.1 in browser and upload "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: add support for Tama W06INAGAKI Hiroshi2018-02-203-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Tama Electric Axing W06 is a 2.4 GHz band 11n router, based on Mediatek MT7688AN. Specification: - MT7688AN (575 MHz) - 64 MB of RAM (DDR2 SDRAM) - 16 MB of Flash (SPI) - 1T1R 2.4 GHz - 1x 10/100/1000 Mbps Ethernet - 4x LEDs (GPIO connected: 3), 1x button - 1x USB 2.0 Type-A (host) - UART header on PCB (GND, RX, TX, Vcc from RJ45 side) Flash instruction using sysupgrade image: 1. Connect micro-USB cable for power supply into W06 and turn on the router 2. Connect to wifi with SSID "tama-*" with password. Complete SSID and password are listed on the back of the router 3. Access to 192.168.1.1 and login with user name "admin" and password empty 4. In firmware update（ファームウェア更新） page, click "参照" button and click "ブラウザー" button to open file browser, select the sysupgrade image and press OK button 5. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: improve GnuBee Personal Cloud Two supportMathias Kresin2018-02-205-17/+6
| | | | | | | | | | | | | | | | | | Use the generic board detection for the GnuBee Personal Cloud Two instead of the target specific one as all recent additions are doing. Fixup the pinmux to set all pins used as GPIO to the function GPIO. Request pins where used. Drop the i2c from the dts. There is nothing connected. While at it fix an indentation issue and use references instead of duplicating the whole node path. Use the same switch config as for the GB-PC1 and drop the led trigger for the not supported IP1001 phy connected to second rgmii. Fixes: c60a21532bc9 ("ramips: Add support for the GnuBee Personal Cloud Two") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use generic board detection for D-Link DAP-1522 A1Mathias Kresin2018-02-204-6/+3
| | | | | | | Use the generic board detection for the D-Link DAP-1522 A1 instead of the target specific one as all recent additions are doing. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-161-9/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for D-Link DAP-1522 A1George Hopkins2018-02-134-9/+17
| | | | | | | | | | | | | | | | | | D-Link DAP-1522 is a wireless bridge/access point with 4 LAN ports and a dual-band wireless chipset. Specifications: - Ralink RT2880 - 32 MB of RAM - 4 MB of Flash - 4x 10/100/1000 Mbps Ethernet (RTL8366SR) - 802.11abgn (RT2850) Flash Instructions: 1. Download lede-ramips-rt288x-dap-1522-a1-squashfs-factory.bin 2. Open the web interface and upload the image Signed-off-by: George Hopkins <george-hopkins@null.net>
* ramips: Add support for the GnuBee Personal Cloud TwoRosen Penev2018-02-135-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The GnuBee Personal Cloud Two crowdfunded on https://www.crowdsupply.com It is a low-cost, low-power, network-attached storage device. Specifications: - SoC: MediaTek MT7621AT - RAM: DDR3 512 MB - Flash: 32 MB - Six SATA ports for 3.5" Drives - One SDcard - One USB 3.0 - Two USB 2.0 - Gigabit Ethernet: Three Ports - UART 3.5mm Audio Jack or 3 pin header - 57600 8N1 - Three GPIOs available on a pin header Flash instructions: The GnuBee Personal Cloud Two ships with libreCMC installed. libreCMC is a Free Software Foundation approved fork of LEDE/OpenWrt. As such one can upgrade using the webinterface or sysupgrade. Das U-Boot has multiple options for recovery or updates including : - USB - http - tftp Errata: - While there are three ethernet ports, the third requires support for the second GMAC. This will come in kernel 4.14. - The first hard drive slot has a clearance issue with the two fan headers. Workaround is to pull the headers out and connect the pins to jumper wires. - Using this device as a NAS is problematic with the 4.9 kernel as many /dev/sdX reads throw silent errors. The current theory behind this is some kind of unhandled DMA mapping error in the kernel. This is not an issue with kernel 4.4. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ramips: add support for TP-Link Archer C50 v3Henryk Heisig2018-02-114-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C50 v3 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7612E. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 2T2R 5 GHz - 5x 10/100 Mbps Ethernet - 4x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Flash instruction: The only way to flash LEDE image in ArcherC50v3 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC50v3-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: various fixes for zbt-we1226Daniel Golle2018-02-065-8/+5
| | | | | | | | | | | Convert userspace code to use generic device-tree compatible board detection method. Users of the existing code will have to use sysupgrade -F once to switch to the new generic board naming. Properly setup pinctrl fixing the switch port LEDs. Fixes commit 9c4fe103cb (ramips: add support for ZBT-WE1226) Reported-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: add support for Widora Neo 32MB flash revisionJackson Ming Hu2018-01-233-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Widora has updated their Widora Neo board recently. The new model uses 32MB WSON-8 factor SPI flash instead of the original 16MB SOP-8 factor SPI flash. All the other hardware components are the same as the first revision. Detailed hardware specs listed below: CPU: MTK MT7688AN RAM: 128MB DDR2 ROM: 32MB WSON-8 factor SPI Flash (Winbond) WiFi: Built-in 802.11n 150Mbps? Ethernet: 10/100Mbps x1 Audio codec: WM8960 Other IO: USB OTG; USB Power+Serial (CP2104); 3x LEDs (Power, LAN, WiFi); 2x Keys (WPS, CPU Reset) 1x Audio In/Out 1x IPEX antenna port 1x Micro SD slot Signed-off-by: Jackson Ming Hu <huming2207@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add flash size postfix to Widora neoMathias Kresin2018-01-234-6/+3
| | | | | | | | | | Rename the Widora neo by adding a flash size prefix. Move the common parts into a dtsi to be prepare everything for upcomming support of the 32MB version. Migrate the Widora neo to the generic board detection as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for ZBT-WE1226Daniel Golle2018-01-235-0/+14
| | | | | | | | MT7628NN (580MHz), 8MB SPI NOR, 64MB DDR2 RAM Everything except for the switch LEDs works great. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ramips: use blue status LED for Xiaomi Router 3GDaniel Gimpelevich2018-01-151-3/+1
| | | | | | | | | | | | The blue LED is what other firmwares use for this device, and it's a lot easier on the eyes than its shade of yellow, which implies an error condition. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [merge into existing $boardname:blue:status block] Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: Piotr Dymacz <pepe2k@gmail.com> Acked-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: add support for TP-Link Archer C20 v4Maxim Anisimov2018-01-154-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v4 is a router with 5-port FE switch and non-detachable antennas. It's based on MediaTek MT7628N+MT7610EN. Specification: - MediaTek MT7628N/N (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 3x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 7x LED (GPIO-controlled*), 2x button, power input switch * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Flash instruction: The only way to flash LEDE image in ArcherC20v4 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.66/24 and tftp server. 2. Rename "openwrt-ramips-mt7628-ArcherC20v4-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: rename TP-Link Archer C20 to TP-Link Archer C20 v1Maxim Anisimov2018-01-155-13/+10
| | | | | | | | This changes device name from "TP-Link Archer C20" to "TP-Link Archer C20 v1" because of TPLINK released new TP-Link Archer C20 v4. Additionally migration to the generic board detection has been made. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: add image checksChen Minqiang2018-01-151-8/+5
| | | | | | | As long as we can't enforce image metadata, we need to use (platform) image checks to have at least soem kind of validation. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for ALFA Network AC1200RMPiotr Dymacz2018-01-154-6/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AC1200RM is an AC1200 router, with 5-port FE switch and USB 2.0 port. Device is based on MediaTek MT7620A + MT7612EN. Specification: - MT7620A (580 MHz) - 64 MB of RAM (DDR2) - 16 MB of FLASH (SPI NOR) - 5x 10/100 Mbps Ethernet with passive PoE output in WAN and LAN4 - 2T2R 2.4 GHz (MT7620A) - 2T2R 5 GHz (MT7612EN) - 1x USB 2.0 - 9x LED (8 driven by GPIO) - 1x button (reset) - DC jack for main power input (12-24 V) - 2x UART, I2C, I2S and LED headers Flash instruction (do it under U-Boot, using UART and TFTP server): Select option "2: Load system code then write to Flash via TFTP" and use "sysupgrade" image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: fix lenovo newifi-y1 switch and LED configChuanhong Guo2018-01-092-3/+5
| | | | | | | | | | | | | | There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on port4. Use a standalone switch configuration to match this and use the switch trigger so that LAN LED could indicate the connetction status for both lan ports correctly. This patch also drop the internet led configuration, because there is a WAN led for port4 and eth0.2 isn't always used as WAN. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: firewrt: indicate boot status via LEDMathias Kresin2018-01-091-0/+1
| | | | | | | Add the Firefly FireWRT gree power LED to diag.sh to indicate the boot status via the power LED. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix widora neo diag ledMathias Kresin2017-12-291-2/+4
| | | | | | | The diag LED is named widora:orange:wifi and can't be derived from the boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix Linkit smart 7688 supportMathias Kresin2017-12-232-1/+4
| | | | | | | | | | Use a more appropriate compatible string. Fix the wireless led GPIO and add the default wireless trigger. Use the wireless LED for boot state indication as well. Remove the GPIO pinmux for pins not exposed on the board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link TL-MR3420 v5Henryk Heisig2017-12-234-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-MR3420 v5 are simple N300 router with 5-port FE switch and non-detachable antennas. Its very similar to TP-Link TL-WR841N V13. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 8 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - USB 2.0 Port - UART (J1) header on PCB (115200 8n1) - 8x LED, 2x button, power input switch Flash instruction: The only way to flash LEDE image in mr3420v5 is to use tftp recovery mode in U-Boot: 1. Configure PC with static IP 192.168.0.225/24 and tftp server. 2. Rename "lede-ramips-mt7628-tplink_tl-mr3420-v5-squashfs-tftp-recovery.bin" to "tp_recovery.bin" and place it in tftp server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. 4. Router will download file from server, write it to flash and reboot. Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for newifi d2Jackson Ming Hu2017-12-214-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | Previously Newifi D2 could only use PandoraBox M1's firmware. It works fine, but LED GPIO is different. As a result, a separated DTS file for this device should be implemented. Hardware spec: * CPU: MTK MT7621A * RAM: 512MB * ROM: 32MB SPI Flash * WiFi: MTK MT7603+MT7612 * Button: 2 buttons (reset, wps) * LED: 3 single-color LEDs (USB, WiFi 2.4GHz, WiFi 5GHz) & 2 dual-color LEDs (Power, Internet) * Ethernet: 5 ports, 4 LAN + 1 WAN Installation method: Same as Newifi D1, users may need to request unlock code from the device manufacturer. Otherwise, a SPI flash programmer may be necessary to get the firmware flashed. After the device is unlocked, press and hold reset button before power cable plugs in. Then go to http://192.168.1.1 to upload and flash the firmware package. Signed-off-by: Jackson Ming Hu <huming2207@gmail.com>
* ramips: add support for Vonets VAR11N-300Andrew Crawley2017-12-213-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VAR11N-300 is a tiny wireless-N device with a hardwired Ethernet cable, one extra Ethernet port, and an internal antenna, based on the MediaTek MT7620n chipset. Specs: - MT7620n WiSoC @ 600MHz - 32 MB SDRAM - 4 MB SPI flash - 2T2R 2.4GHz WiFi-N - 1 attached 10/100 Ethernet cable (LAN) - 1 10/100 Ethernet port (WAN) - 1 attached USB / barrel 5vdc power cable - 5 LEDs (see notes below) - 1 reset button - 1 UART (3 pads on board) Installation: The stock firmware does not support uploading new firmware directly, only checking the manufacturer's site for updates. This process may be possible to spoof, but the update check uses some kind of homebrew encryption that I didn't investigate. Instead, you can install via a backdoor: 1. Set up a TFTP server to serve the firmware binary (lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin) 2. Factory reset the device by holding the reset button for a few seconds. 3. Open the web interface (default IP: 192.168.253.254) 4. Log in with the "super admin" credentials: username `vonets`, password `vonets26642519`. 5. On the "Operative Status" page, click the text "System Uptime", then quickly click the uptime value. 6. If successful, an alert dialog will appear reading "Ated start", and the device will now accept telnet connections. If the alert does not appear, repeat step 5 until it works (the timing is a bit tricky). 7. Telnet to the device using credentials "admin / admin" 8. Retrieve the firmware binary from the tftp server: `tftp -l lede.bin -r lede-ramips-mt7620-var11n-300-squashfs-sysupgrade.bin -g <tftp-server-ip>` 9. Write the firmware to flash: `mtd_write write lede.bin /dev/mtd4` 10. Reboot Tested: - LAN / WAN ethernet - WiFi - LAN / WAN / status LED GPIOs (see notes below) - Reset button - Sysupgrade Notes: LEDs: The board has 5 LEDs - two green LEDs for LAN / WAN activity, one blue LED for WiFi, and a pair of "status" LEDs connected to the same GPIO (the blue LED lights when the GPIO is low, and the green when it's high). I was unable to determine how to operate the WiFi LED, as it does not appear to be controlled by a GPIO directly. Recovery: The default U-boot installation will only boot from flash due to a missing environment block. I generated a valid 4KB env block using U-boot's `fw_setenv` tool and wrote it to flash at 0x30000 using an external programmer. After this, it was possible to enter the U-boot commandline interface and download a new image via TFTP (`tftpboot 81b00000 <image-filename>`), but while I could boot this image sucessfully (`bootm`), writing it to flash (`cp.linux`) just corrupted the flash chip. The sysupgrade file can be written to flash at 0x50000 using an external programmer. Signed-off-by: Andrew Crawley <acrawley@gmail.com>
* ramips: add helper variable for boardnameMathias Kresin2017-12-212-224/+226
| | | | | | | | | | | | | Add a helper variable which contains the boardname separated from the vendor name. It allows to switch to a device tree compatible string based boardname, by keeping the $board:colour:function syntax in scripts handling/adding config for LEDs. Boards not using the device tree compatible string as based boardname are unaffected by the change, since none of them uses a comma in the boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fallback to generic board detectMathias Kresin2017-12-213-14/+6
| | | | | | | Fallback to the generic board detection if no case for the current board exists. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop LinkIt Smart 7688 Duo userspace supportMathias Kresin2017-12-214-13/+3
| | | | | | | | | | The LinkIt Smart 7688/LinkIt Smart 7688 Duo are identical beside the extra ATmega32U4 - accessible via UART - on the the Duo. Since all relevant hardware is identical, drop the Duo special handling in userspace. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: fix a typo in 02_networkPavel Kubelun2017-12-081-1/+1
| | | | | | | The typo in network defaults script in ramips target that prevents defaults to initialize. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ramips: add support for Asus RT-N11P / RT-N12+ / RT-N12E b1Zoltan HERPAI2017-12-064-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | This is a variant of the MT7620N-based Asus routers. Specifications: - MT7620N (580 MHz) - 32 MB RAM - 8 MB Flash - 5x 10/100Mbps Ethernet (built-in switch) - 2.4 GHz WLAN - 2x external, non-detachable antennas - UART (J2) header on PCB (115200 8n1) Flash instructions: 1. Configure PC with static IP 192.168.1.75/24 2. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds. All 4 LEDs will start to blink, which is when the router will accept firmware files via TFTP. No known limitations on firmware filenames, just send it with a TFTP client to 192.168.1.1. 3. Router will download file from server, write it to flash and reboot. Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* ramips: add support for ZBT WE3526Felix Fietkau2017-11-162-0/+2
| | | | | | | | | | | | | | | | | This is a variant of the ZBT WG3526 with a few minor modifications. The wifi chips are swapped, and there is no GPIO controllable status LED. There is also no SATA port. Specifications: - MT7621AT (880 MHz) - 512 MB RAM - 16 MB Flash (SPI NOR) - 5x 1Gbps Ethernet (built-in switch) - MT7612E 802.11ac 5 GHz WLAN - MT7603E 802.11n 2.4 GHz WLAN Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: extract board name from device tree as a fallbackFelix Fietkau2017-11-161-1/+3
| | | | | | | This makes it possible to avoid more duplication when adding support for a new board Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add support for UniElec U7628-01Piotr Dymacz2017-11-145-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7628-01 is a router platform board based on MediaTek MT7628AN. The device has the following specifications: - MT7628AN (580MHz) - 64/128/256 MB of RAM (DDR2) - 8/16 MB of flash (SPI NOR) - 5x 10/100 Mbps Ethernet (MT7628 built-in switch) - 1x 2T2R 2.4 GHz Wi-Fi (MT7628) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 1x miniSIM slot - 1x microSD slot - 1x USB 2.0 port - 7x single-color LEDs (GPIO-controlled) - 1x bi-color LED (green GPIO-controlled, red -> LED_WLAN# in miniPCIe) - 1x reset button - 1x UART header (4-pins) - 1x SDXC/GPIO header (10-pins, connected with microSD slot) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slot (tested with modem and Wi-Fi card) - miniSIM slot - sysupgrade - reset button - USB 2.0 port* Due to a missing driver (MMC over GPIO) this is not supported: - microSD card reader * Warning: USB buses in miniPCIe and regular A-type socket are connected together, without any proper analog switch or USB HUB. Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 128MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt76x8-u7628-01-128M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. SDXC/GPIO header (J3): 1. SDXC_D3 / I2C_SCLK 2. SDXC_D2 / I2C_SD 3. SDXC_D1 / I2S_DI 4. SDXC_D0 / I2S_WS 5. SDXC_CMD / I2S_CLK 6. SDXC_CLK / GPIO0 7. SDXC_CD / UART_RXD1 8. UART_TXD1 9. 3V3 10. GND Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 128/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for UniElec U7621-06Piotr Dymacz2017-11-144-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | UniElec U7621-06 is a router platform board based on MediaTek MT7621AT. The device has the following specifications: - MT7621AT (880 MHz) - 256/512 MB of RAM (DDR3) - 8/16/32/64 MB of FLASH (SPI NOR) - 5x 1 Gbps Ethernet (MT7621 built-in switch) - 1x ASMedia ASM1061 (for mSATA and SATA) - 2x miniPCIe slots (PCIe bus only) - 1x mSATA slot (with USB 2.0 bus for modem) - 1x SATA - 1x miniSIM slot - 1x microSD slot - 1x USB 3.0 - 12x LEDs (3 GPIO-controlled) - 1x reset button - 1x UART header (4-pins) - 1x GPIO header (30-pins) - 1x FPC connector for LEDs (20-pin, 0.5 mm pitch) - 1x DC jack for main power (12 V) The following has been tested and is working: - Ethernet switch - miniPCIe slots (tested with Wi-Fi cards) - mSATA slot (tested with modem and mSATA drive) - miniSIM slot - sysupgrade - reset button - microSD slot Installation: This board might come with a different firmware versions (MediaTek SDK, PandoraBox, Padavan, etc.). If your board comes with PandoraBox, you can install LEDE using sysupgrade. Just SSH to the router and perform forced sysupgrade (due to a board name mismatch). The default IP of this board should be: 192.168.1.1 and username/password: root/admin. In case of a different firmware, you can use web based recovery described below. Use the following command to perform the sysupgrade (for the 256MB RAM/16MB flash version): sysupgrade -n -F lede-ramips-mt7621-u7621-06-256M-16M-squashfs-sysupgrade.bin Recovery: This board contains a Chinese, closed-source bootloader called Breed (Boot and Recovery Environment for Embedded Devices). Breed supports web recovery and to enter it, you keep the reset button pressed for around 5 seconds during boot. Your machine will be assigned an IP through DHCP and the router will use IP address 192.168.1.1. The recovery website is in Chinese, but is easy to use. Click on the second item in the list to access the recovery page, then the second item on the next page is where you select the firmware. In order to start the recovery, you click the button at the bottom. LEDs list (top row, left to right): - LED_WWAN# (connected with pin 42 in LTE/mSATA slot) - Power (connected directly to 3V3) - CTS2_N (GPIO10, configured as "status" LED) - TXD2 (GPIO11, configured as "led4", without default trigger) - RXD2 (GPIO12, configured as "led5", without default trigger) - LED_WLAN# (connected with pin 44 in wifi0 slot) LEDs list (bottom row, left to right): - ESW_P0_LED_0 - ESW_P1_LED_0 - ESW_P2_LED_0 - ESW_P3_LED_0 - ESW_P4_LED_0 - LED_WLAN# (connected with pin 44 in wifi1 slot) Other notes: 1. The board is available with different amounts of RAM and flash. We have only added support for the 256/16 MB configuration, as that seems to be the default. However, all the required infrastructure is in place for making support for the other configurations easy. 2. The manufacturer offers five different wireless cards with MediaTek chipsets, based on MT76x2, MT7603 and MT7615. Images of the board all show that the miniPCIe slots are dedicated to specific Wi-Fi cards. However, the slots are generic. 3. All boards we got access to had the same EEPROM content. The default firmware reads the Ethernet MAC from offset 0xe000 in factory partition. This offset only contains 0xffs, so a random MAC will be generated on every boot of the router. There is a valid MAC stored at offset 0xe006 and this MAC is shown as the WAN MAC in the bootloader. However, it is the same on all boards we have checked. Based on information provided by the vendor, all boards sold in small quantities are considered more as samples for development purposes. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com> Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for TP-Link TL-WR840N v5Robert Marko2017-11-084-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR840N v5 is simple N300 router with 5-port FE switch and non-detachable antennas, based on MediaTek MT7628NN (aka MT7628N) WiSoC. Specification: - MT7628N/N (580 MHz) - 64 MB of RAM (DDR2) - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 1x LED (GPIO-controlled), 1x button * LED in TL-WR840N v5 is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the green part of the LED. Orange LED is registered so you can later use it for your own purposes. Flash instruction: Unlike TL-WR840N v4 flashing through WEB UI works in v5. 1. Download lede-ramips-mt76x8-tl-wr840n-v5-squashfs-sysupgrade.bin image. 2. Go to 192.168.0.1 3. Flash the sysupgrade image through Firmware upgrade section of WEB UI. 4. Wait until green LED stops flashing and use the router. Notes: TFTP recovery is broken since TP-Link reused bootloader code for v4 and that does not take into account only 4 MB of flash and bricks the device. So do not use TFTP Recovery or you will have to rewrite SPI flash. They fixed it in later GPL code,but it is unknown which version of bootloader you have. After manually compiling and flashing bootloader from GPL sources TFTP recovery works properly. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ramips: fix Youku-YK1 supportEdmunt Pienkowsky2017-10-272-2/+3
| | | | | | | | | | | | | | | | | | | | | | Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Kimax U25AWF-H1Daniel Kucera2017-10-145-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Kimax U-25AWF-H1 is is a 2,5" HDD Enclosure with Wi-Fi/Eth conection and battery, based on MediaTek MT7620A. Patch rewritten from: https://forum.openwrt.org/viewtopic.php?pid=305643 Specification: - MT7620A CPU - 64 MB of RAM - 16 MB of FLASH - 802.11bgn WiFi - 1x 10/100 Mbps Ethernet - USB 2.0 Host - UART for serial console Flash instruction: 1. Download lede-ramips-mt7620-u25awf-h1-squashfs-sysupgrade.bin 2. Open webinterface a upgrade 3. After boot connect via ethernet to ip 192.168.1.1 Signed-off-by: Daniel Kucera <daniel.kucera@gmail.com> [fix reset button gpio, don't add a lan/wan vlan config for single port board, add -H1 suffix do make sure that this revision of the board is supported/tested] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: improve Xiaomi Mi Router 3G supportKevin Darbyshire-Bryant2017-09-282-4/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit improves support for the Xiaomi Mi Router 3G originally added in commit 6e283cdc0da25928f8148805ebef7f8f2b769ee8 Improvements: - Remove software watchdog as hardware watchdog now working as per commit 3fbf3ab44f5cebb22e30a4c8681b13341feed6a6 for all mt7621 devices. - Reset button polarity corrected - length of press determines reboot (short press) vs. reset to defaults (long press) behaviour. - Enable GPIO amber switch port LEDs on board rear - lit indicates 1Gbit link and blink on activity. Green LEDs driven directly by switch indicating any link speed and tx activity. - USB port power on/off GPIO exposed as 'usbpower' - Add access to uboot environment settings for checking/setting uboot boot order preference from user space. Changes: - Front LED indicator is physically made of independent Yellow/Amber, Red & Blue LEDs combined via a plastic 'lightpipe' to a front panel indicator, hence the colour behaviour is similar to an RGB LED. RGB LEDs are not supported at this time because they produce colour results that do not then match colour labels, e.g. enabling 'mir3g:red' and 'mir3g:blue' would result in a purple indicator and we have no such label for purple. The yellow, red & blue LEDs have been split out as individual yellow, red & blue status LEDs, with yellow being the default status LED as before and with red's WAN and blue's USB default associations removed. - Swapped order of vlan interfaces (eth0.1 & eth0.2) to match stock vlan layout. eth0.1 is LAN, eth0.2 is WAN - Add 'lwlll' vlan layout to mt7530 switch driver to prevent packet leakage between kernel switch init and uci swconfig uboot behaviour & system 'recovery' uboot expects to find bootable kernels at nand addresses 0x200000 & 0x600000 known by uboot as "system 1" and "system 2" respectively. uboot chooses which system to hand control to based on 3 environment variables: flag_last_success, flag_try_sys1_failed & flag_try_sys2_failed last_success represents a preference for a particular system and is set to 0 for system 1, set to 1 for system 2. last_success is considered *if* and only if both try_sys'n'_failed flags are 0 (ie. unset) If *either* failed flags are set then uboot will attempt to hand control to the non failed system. If both failed flags are set then uboot will check the uImage CRC of system 1 and hand control to it if ok. If the uImage CRC of system is not ok, uboot will hand control to system 2 irrespective of system 2's uImage CRC. NOTE: uboot only ever sets failed flags, it *never* clears them. uboot sets a system's failed flag if that system's was selected for boot but the uImage CRC is incorrect. Fortunately with serial console access, uboot provides the ability to boot an initramfs image transferred via tftp, similarly an image may be flashed to nand however it will flash to *both* kernels so a backup of stock kernel image is suggested. Note that the suggested install procedure below set's system 1's failed flag (stock) thus uboot ignores the last_success preference and boots LEDE located in system 2. Considerable thought has gone into whether LEDE should replace both kernels, only one (and which one) etc. LEDE kernels do not include a minimal rootfs and thus unlike the stock kernel cannot include a method of controlling uboot environment variables in the event of rootfs mount failure. Similarly uboot fails to provide an external mechanism for indicating boot system failure. Installation - from stock. Installation through telnet/ssh: - copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it from LEDE download site to /tmp - switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if wgetted from LEDE download site - run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1 - run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0 - run: nvram set flag_try_sys1_failed=1 - run: nvram commit - run: reboot Recovery - to stock. Assuming you used the above installation instructions you will have a stock kernel image in system 1. If it can be booted then it may be used to perform a stock firmware recovery, thus erasing LEDE completely. From a 'working' LEDE state (even failsafe) Failsafe only: - run: mount_root - run: sh /etc/uci-defaults/30_uboot-envtools Then do the steps for 'All' All: - run: fw_setenv flag_try_sys2_failed 1 - run: reboot The board will reboot into system 1 (stock basic kernel) and wait with system red light slowly blinking for a FAT formatted usb stick with a recovery image to be inserted. Press and hold the reset button for around 1 second. Status LED will turn yellow during recovery and blue when recovery complete. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ramips: mt7621: fix failsafe mode networkingKevin Darbyshire-Bryant2017-09-281-2/+7
| | | | | | | | | | Disable VLANs on mt7621 boards with mt7530 switches on failsafe entry. Allows failsafe networking to work correctly. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> [fixed default case syntax error] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for TP-Link Archer C20 v1Maxim Anisimov2017-09-135-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link Archer C20 v1 is a router with 5-port FE switch and non-detachable antennas. It's very similiar to TP-Link Archer C50. Also it's based on MediaTek MT7620A+MT7610EN. Specification: - MediaTek MT7620A (580 Mhz) - 64 MB of RAM - 8 MB of FLASH - 2T2R 2.4 GHz and 1T1R 5 GHz - 5x 10/100 Mbps Ethernet - 2x external, non-detachable antennas - UART (J1) header on PCB (115200 8n1) - 8x LED (GPIO-controlled*), 2x button, power input switch - 1 x USB 2.0 port * WAN LED in this devices is a dual-color, dual-leads type which isn't (fully) supported by gpio-leds driver. This type of LED requires both GPIOs state change at the same time to select color or turn it off. For now, we support/use only the blue part of the LED. * MT7610EN ac chip isn't not supported by LEDE. Therefore 5Ghz won't work. Factory image notes: These devices use version 3 of TP-Link header, fortunately without RSA signature (at least in case of devices sold in Europe). The difference lays in the requirement for a non-zero value in "Additional Hardware Version" field. Ideally, it should match the value stored in vendor firmware header on device. We are able to prepare factory firwmare file which is accepted and (almost) correctly flashed from the vendor GUI. As it turned out, it accepts files without U-Boot image with second header at the beginning but due to some kind of bug in upgrade routine, flashed image gets corrupted before it's written to flash. So, to flash this device we must to prepare image using original firmware from tp-link site with uboot. Flash instruction: Until (if at all) TP-Link fixes described problem, the only way to flash LEDE image in these devices is to use tftp recovery mode in U-Boot. There are two ways to flash the device to LEDE: 1) Using tftp mode with UART connection and original LEDE image - Place lede-ramips-mt7620-ArcherC20-squashfs-factory.bin in tftp server directory - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, power up the router and press key "4" to access U-Boot CLI. - Use the following commands to update the device to LEDE: setenv serverip 192.168.0.66 tftp 0x80060000 lede-ramips-mt7620-ArcherC20-squashfs-factory.bin erase tplink 0x20000 0x7a0000 cp.b 0x80060000 0x20000 0x7a0000 reset - After that the device will reboot and boot to LEDE 2) Using tftp mode without UART connection but require some manipulations with target image - Download and unpack TP-Link Archer C20 v1 firmware from original web site - Split uboot.bin from original firmware by this command (example): dd if=Archer_C20v1_0.9.1_4.0_up_boot(160427)_2016-04-27_13.53.59.bin of=uboot.bin bs=512 count=256 skip=1 - Create ArcherC20V1_tp_recovery.bin using this command: cat uboot.bin lede-ramips-mt7620-ArcherC20-squashfs-factory.bin > ArcherC20V1_tp_recovery.bin - Place ArcherC20V1_tp_recovery.bin in tftp server directory. - Configure PC with static IP 192.168.0.66/24 and tftp server. - Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed for around 6-7 seconds, until device starts downloading the file. - Router will download file from server, write it to flash and reboot. Signed-off-by: Maxim Anisimov <maxim.anisimov.ua@gmail.com>
* ramips: fix hg255d LED status supportDavid Yang2017-09-131-0/+1
| | | | | | | | Use the green power LED for boot status indication. Source: https://my.oschina.net/osbin/blog/278782 Para 3 Signed-off-by: David Yang <mmyangfl@gmail.com>
* ramips: Add support for ZBT WE1026-5GKristian Evensen2017-09-114-1/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZBT WE1026-5G (http://www.zbtlink.com/products/router/WE1026-5G.html) is the follow-up to the ZBT WE1026 and is based on MT7620. For the previous WE1026, the ZBT WE826 image could be used. However, as the name implies, the -5G comes equipped with a 5GHz wifi radio. As the WE826 only has a 2.4GHz radio, the addition of 5GHz means that a separate image is needed for the WE1026-5G. I suspect that this image will also work on the previous WE1026, but I don't have a device to test with. The WE1026-5G has following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x 5GHz wifi (MT7612) * 1x button. * 3x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working: * The 5GHz WIFI LED is completely dead. I suspect the issue is the same as on other devices with Mediatek 5Ghz wifi-cards/chips. The LED is controlled by the driver, and mt76 (currently) does not support this. Not tested: * SD card reader. Notes: * The modem (labeled 3G/4G) and power LEDs are controlled by the hardware. * There is a 32MB version of this device available, but I do not have access to it. I have therefor only added support for the 16MB version, but added all the required infrastructure to make adding support for the 32MB version easy. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the WE1026-5G supports recovery using HTTP. Keep the reset button pressed for ~5sec when booting to start the web server. Set the address of the network interface on your machine to 192.168.1.2/24, and point your browser to 192.168.1.1 to access the recovery UI. From the recovery UI you can upload a firmware image. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for the HNET C108Kristian Evensen2017-09-095-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The HNET C108 (http://www.szhwtech88.com/Product-product-cid-100-id-4374.html) is a mifi based on MT7602A, which has the following specifications: * CPU: MT7620A * 1x 10/100Mbps Ethernet. * 16 MB Flash. * 64 MB RAM. * 1x USB 2.0 port. Only power is connected, this port is meant for charging other devices. * 1x mini-PCIe slots. * 1x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. * 6000 mAh battery. * 5x controllable LEDs. Works: * Wifi. * Switch. * mini-PCIe slot. Only tested with a USB device (a modem). * SIM slot. * Sysupgrade. * Button (reset). Not working (also applies to the factory firmware): * Wifi LED. It is always switched on, there is no relation to the up/down state or activity of the wireless interface. Not tested: * SD card reader. Notes: * The C108 has no dedicated status LED. I therefore set the LAN LED as status LED. Installation: The router comes pre-installed with OpenWRT, including a variant of Luci. The initial firmware install can be done through this UI, following normal procedure. I.e., access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. Recovery: If you brick the device, the C108 supports recovery using TFTP. Keep the reset button pressed for ~5sec when booting to trigger TFTP. Set the address of the network interface on your machine to 10.10.10.3/24, and rename your image file to Kernal.bin. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: fix default LED configurationKristian Evensen2017-09-061-0/+0
| | | | | | | | | | | | | | | Commit 77645ffcd9ad ("ramips: add support for the GnuBee Personal Cloud One") dropped the execution permission from 01_leds with the result that the file isn't started during first boot and no default LED configuration is added. Revert the introduced file permission change. Fixes: FS#979 Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [cherry picked the fix from a board support patch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add Xiaomi Mi Router 3G supportPavel Kubelun2017-08-235-0/+19
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for Xiaomi Mi WiFi Router 3G. Short specification: - MT7621AT + MT7603EN + 7612EN - 256MB DDR3 RAM - 128MB NAND flash - 1+2 x 1000M Ethernet - 1x USB 3.0 port - reset button - yellow, blue, red leds Installation through telnet/ssh: - copy lede-ramips-mt7621-mir3g-squashfs-kernel1.bin and lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin to usb disk or wget it from LEDE download site to /tmp - switch to /extdisks/sda1/ (if copied to USB drive) or to /tmp if wgetted from LEDE download site - run: mtd write lede-ramips-mt7621-mir3g-squashfs-kernel1.bin kernel1 - run: mtd write lede-ramips-mt7621-mir3g-squashfs-rootfs0.bin rootfs0 - run: mtd erase kernel0 - run: reboot Originally stock firmware has following partitions: - ... - kernel0 (primary kernel image) - kernel1 (secondary kernel image, used by u-boot in failsafe routine) - rootfs0 (primary rootfs) - rootfs1 (secondary rootfs in case primary fails) - overlay (used as ubi overlay) This commit squashes rootfs0, rootfs1 and overlay partitions into 1, so it can be used by LEDE fully for package installation, resulting in 117,5MiB. This device lacks hw watchdog, so adding softdog instead (stock does the same). Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ramips: add support for the VoCore2 LiteL. D. Pinney2017-08-115-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | The VoCore2 Lite uses the same PCB as the Vocore2. This patch moves the common VoCore2 parts into dtsi. Removed memory node in the device tree source file. Memory is detected automatically. http://vocore.io/ http://vonger.net/ http://vonger.cn/ Specifications: - SoC: MediaTek MT7688AN - RAM: 64MB DDR2 EtronTech EM68B16CWQH-25H - Flash: 8MB NOR SPI Flash GigaDevice GD25Q64CWIG - Wireless: Built into MT7688AN with onboard IPEX connector Firmware installation: - VoCore2-Lite ships with firmware forked from OpenWrt. - Installation from the bootloader is recommended. - If using luci/sysupgrade use the -n option (do not keep settings) original firmware uses a modified proprietary MediaTek wireless driver. - The wireless is disabled by default in LEDE. - If reverting to factory firmware using the bootloader is recommended. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> Tested by: Noble Pepper <noblepepper@gmail.com>
* ramips: Add support for Netgear EX3800Thibaut VARENE2017-08-031-1/+1
| | | | | | | | | | | | The Netgear EX3800 is essentially an EX3700 with a mains output socket. Both devices use the exact same firmware image (original firmware is named EX3700-EX3800-version.chk). This patch adds suport by renaming the EX3700 device to EX3700/EX3800 and updating the necessary glue. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: cleanup EX2700 and WN3000RPv3 LEDsThibaut VARENE2017-08-032-5/+4
| | | | | | | | | | | | | | | This patch cleans up the WN3000RPv3 and EX2700 setup, bringing it in line with other similar devices: The power led is a bicolor one. The bootloader brings the red side on at powerup. Instead of blinking the red side in diag.sh and need to forcefully turn it off in 01_leds, this patch simplifies the setup by relying on the default off state of the gpio-led driver for the red side and blinking the green side as with other devices. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: drop AsiaRF AWM003 eval boardMathias Kresin2017-08-033-5/+0
| | | | | | | Everything is identical to the AWM002 8m eval board. No need to duplicate it once more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: drop Edimax BR-6425 supportMathias Kresin2017-08-033-7/+0
| | | | | | Code to build an image for the Edimax BR-6425 never existed. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-05 03:41:56 +0000