aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files
Commit message (Collapse)AuthorAgeFilesLines
...
* ramips: consistently use lower-case factory partition labelAdrian Schmutzler2019-07-251-7/+5
| | | | | | | | The vast majority of devices labels "factory" partition with lower case. Convert the small fraction with capital letter to that and merge another case in 02_network. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate MAC address cases in 02_networkAdrian Schmutzler2019-07-251-32/+15
| | | | | | | | This just merges some duplicate definitions and consolidates lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated cases for phicomm k2p]
* ramips: fix mac addresses used by Phicomm K2PChuanhong Guo2019-07-251-0/+4
| | | | | | | | | | | Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses at 0xe000/0xe006 of factory partition. Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network uses lan_mac+1. Add a special case reading lan/wan mac address for Phicomm K2P. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: sysupgrade: get rid of platform_nand_pre_upgrade()Rafał Miłecki2019-07-222-13/+6
| | | | | | | | | | | 1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: add support for TP-Link RE650 v1Georgi Vlaev2019-07-172-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v1 is a dual-band AC2600 range extender, based on MediaTek MT7621A and MT7615E. According to the wikidevi entry for RE650 this device is identical with TP-Link RE500 as hardware. This patch supports only RE650. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com> [re-added variables for kernel header] Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-4/+4
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: get rid of platform_pre_upgrade()Rafał Miłecki2019-07-161-12/+8
| | | | | | | | | | | The only step between platform_pre_upgrade() and platform_do_upgrade() is switching to ramdisk. It should be fine to "mtd erase firmware" from the later callback and get rid of the first one. This change wasn't tested on affected target but identical code logic was verified to work as expected on brcm47xx with initramfs firmware. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ramips: Remove left-over mistyped device string from 02_networkAdrian Schmutzler2019-07-161-1/+0
| | | | | | | | | | | In 2011 (!), network setup for nexaira,bc2 was moved to network defaults script with a typo so it became b2c: 295e04084c ("ramips: setup bc2 mac addresses from the generic network script") This patch just removes the useless entry without replacement, since it seems to have worked for 8 years anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ASUS RT-AC57UDavid Bauer2019-07-111-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix mqmaker witi case in fixup-mac-addressChuanhong Guo2019-07-111-2/+1
| | | | | | | This commit fixes a forgotten case in previous commit. Fixes: 087e14ab59 ("ramips: mt7621: merge two variants of MQmaker WiTi together") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: merge two variants of MQmaker WiTi togetherChuanhong Guo2019-07-111-2/+1
| | | | | | | Since we can auto-detect memory now, we don't need 2 dts for two memory variants. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Reapply sorting to board.d filesAdrian Schmutzler2019-07-103-521/+521
| | | | | | | | This patch is cosmetical: It only applies sorting based on device names, whereas renames already took place in earlier patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Remove base-files/lib/ramips.shAdrian Schmutzler2019-07-103-36/+0
| | | | | | | | | | Having converted the target to use device compatible, ramips.sh is obsolete now. The only remaining entry for the mt7688 evaluation board seems to be orphaned. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt288x,rt3883: Name DTS files based on schemeAdrian Schmutzler2019-07-101-2/+2
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt305x: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-104-439/+130
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-104-79/+31
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt76x8: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-103-89/+32
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7621: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-107-132/+51
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-105-316/+123
| | | | | | | | | | | | | | | This will "rename" devices in Makefiles to the pattern used in DTS compatible. This will systematize naming of devices enormously. As device names are used to for default SUPPORTED_DEVICES entries, we need to adjust the source for /tmp/sysinfo/board_name, too. So remove relevant entries from base-files/lib/ramips.sh and use device compatible for that. Despite that, base-files are updated, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Improve compatible for TP-Link Archer devicesAdrian Schmutzler2019-07-103-11/+11
| | | | | | | | Include "Archer" in compatible as it is part of the device name. Update Makefile device names where necessary to match compatible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link TL-WR841n v14Alexander Müller2019-07-022-0/+5
| | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N. - MediaTek MT7628NN - 32 MB of RAM - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet Installation: - copy the 'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin' file to your tftp server root and rename it to 'tp_recovery.bin'. - configure your PC running the TFTP server with the static IP address 192.168.0.66/24 - push the reset button and plug in the power connector. Wait until the orange led starts blinking (~6sec) Signed-off-by: Alexander Müller <donothingloop@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
* ramips/leds: use devicetree alias led_wlanAlexander Couzens2019-07-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | Similiar to the lantiq target use a dts alias to define the wlan led instead of static mapping in /etc/board.d/01_leds. Reduce code duplication. A device tree must define the alias "led-wlan" similiar to "led-boot". / { aliases { led-wlan = &led_wlan; }; [..] led_wlan: wlan { label = "tl-wr841n-v14:green:wlan"; gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; }; }; Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for TOTOLINK A7000RChuanhong Guo2019-06-261-0/+1
| | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 128MB - Flash: 16M SPI NOR - Ethernet: 5x GE ports - WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: Upload generated sysupgrade firmware through factory web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: mt7621: Add new device AsiaRF AP7621-001Daniel Danzberger2019-06-251-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware specs: SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (1 x LAN, 1 x WAN) USB: 1x 3.0 PCI: 3x Mini PCIe GPS: Quectel L70B BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation: The stock image is a modified openwrt and can be overflashed via # sysupgrade -F image.bin Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed unused label, formatting]
* ramips: fix GELAN port in D-Link DWR-118-A2Pawel Dembicki2019-06-201-1/+1
| | | | | | | This patch fix and enable GELAN port in D-LINK DWR-118-A2. Tested-by: Richard Toth <trtk1992@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ramips: add support for Edimax EW-7478APCBirger Koblitz2019-06-201-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac Switch: Mediatek MT7530W Gigabit Switch (4 x LAN, 1 x WAN) USB: Yes 1 x 2.0 (+ 1 x 2.0 unpopulated header) BTN: Reset/WPS LED: - Power (white) - Internet (blue) - Wifi (blue) - USB (blue) UART: UART is present as Pads with throughholes on the PCB. They are located in the lower right corner (GbE ports facing up) 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimax.setup) Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflicts in 01_leds and mt7620.mk, dts whitespace issues] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax EW-7476RPC / EW-7478ACBirger Koblitz2019-06-202-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: 192.168.9.2/24). http://192.168.9.2/index.asp ramips: add Edimax EW-7478AC SoC: MediaTek MT7620a @ 580MHz RAM: 64M (Winbond W9751G6KB-25) FLASH: 8MB (Macronix) WiFi: SoC-integrated: MediaTek MT7620a bgn WiFi: MediaTek MT7612EN nac GbE: 1x (RTL8211E) BTN: WPS - RFKILL/RF 50%/RF 100% toggle LED: - Wifi 5g (blue) - Wifi 2g (blue) - Crossband (green) - Power (green) - WPS (green) - LAN (Green) UART: UART is present as Pads with throughholes on the PCB. They are located next to the switch for the wifi configuration 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the web-interfaces (by default: http://edimaxext.setup) Or push wpa button on power on and send firmware via tftp to 192.168.1.6 The EW-7478AC is identical to the EW-7476RPC, except instead of 2 internal antennas it has 2 external ones. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [merge conflict in 01_leds] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Remove redundant LED-casesKristian Evensen2019-06-101-68/+32
| | | | | | | 01_leds has several redundant LED-cases. This commit cleans up the file by merging these cases into shared cases. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for TOTOLINK LR1200Chuanhong Guo2019-06-051-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: - SoC: MT7628DAN (MT7628AN with 64MB built-in RAM) - Flash: 8M SPI NOR - Ethernet: 5x 10/100Mbps - WiFi: 2.4G: MT7628 built-in 5G: MT7612E - 1x miniPCIe slot for LTE modem (only USB pins connected) - 1x SIM slot Flash instruction: U-boot has a builtin web recovery page: 1. Hold the reset button while powering it up 2. Connect to the ethernet and set an IP in 192.168.1.0/24 range 3. Open your browser and upload firmware through http://192.168.1.1 Note about the LTE modem: If your router comes with an EC25 module and it doesn't show up as a QMI device, you should do the following to switch it to QMI mode: 1. Install kmod-usb-serial-option and a terminal software (e.g. minicom or screen). All 4 serial ports of the modem should be available now. 2. Open /dev/ttyUSB3 with the terminal software and type this AT command: AT+QCFG="usbnet",0 3. Power-cycle the router. You should now get a QMI device recognized. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: create R6220 dtsi and improve WNDR3700v5 supportJan Hoffmann2019-05-312-3/+5
| | | | | | | | | | | | | | | | | | The R6220 and WNDR3700v5 are identical apart from using NAND/NOR flash and having a different casing. This adds a new cleaned up R6220.dtsi with the common bits for both devices. Both devices now have feature parity. Performed cleanup: * generic DTS node names * regulator for usb power * added missing pinctrl groups * use switch port instead of VLAN as trigger for WAN LED Fixes for WNDR3700v5: * all LEDS work * correct ethernet MAC addresses Signed-off-by: Jan Hoffmann <jan@3e8.eu>
* ramips: add support for Xiaomi Mi Router 4A (100M Edition)Markus Scheck2019-05-311-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | - SoC: MediaTek MT7628AN - Flash: 16MB (Winbond W25Q128JV) - RAM: 64MB - Serial: As marked on PCB, 3V3 logic, baudrate is 115200 - Ethernet: 3x 10/100 Mbps (switched, 2x LAN + WAN) - WIFI0: MT7628AN 2.4GHz 802.11b/g/n - WIFI1: MT7612EN 5GHz 802.11ac - Antennas: 4x external (2 per radio), non-detachable - LEDs: Programmable power-LED (two-colored, yellow/blue) Non-programmable internet-LED (shows WAN-activity) - Buttons: Reset INSTALLATION: 1. Connect to the serial port of the router and power it up. If you get a prompt asking for boot-mode, go to step 3. 2. Unplug the router after > Erasing SPI Flash... > raspi_erase: offs:20000 len:10000 occurs on the serial port. Plug the router back in. 3. At the prompt select option 2 (Load system code then write to Flash via TFTP.) 4. Enter 192.168.1.1 as the device IP and 192.168.1.2 as the Server-IP. 5. Connect your computer to LAN1 and assign it as 192.168.1.2/24. 6. Rename the sysupgrade image to test.bin and serve it via TFTP. 7. Enter test.bin on the serial console and press enter. Signed-off-by: Markus Scheck <markus@mscheck.de> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added mt76 compatible]
* ramips: add CUDY WR1000 supportDavide Fioravanti2019-05-312-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cudy WR1200 is an AC1200 AP with 3-port FE and 2 non-detachable antennas Specifications: MT7628 (580 MHz) 64 MB of RAM (DDR2) 8 MB of FLASH 2T2R 2.4 GHz (MT7628) 2T2R 5 GHz (MT7612E) 3x 10/100 Mbps Ethernet (2 LAN + 1 WAN) 2x external, non-detachable antennas (5dbi) UART header on PCB (57600 8n1) 7x LED, 2x button Known issues: The Power LED is always ON, probably because it is connected directly to power. Flash instructions ------------------ Load the ...-factory.bin image via the stock web interface. Openwrt upgrade instructions ---------------------------- Use the ...-sysupgrade.bin image for future upgrades. Revert to stock FW ------------------ Warning! This tutorial will work only with the following OEM FW: WR1000_EU_92.122.2.4987.201806261618.bin WR1000_US_92.122.2.4987.201806261609.bin If in the future these firmwares will not be available anymore, you have to find the new XOR key. 1) Download the original FW from the Cudy website. (For example WR1000_EU_92.122.2.4987.201806261618.bin) 2) Remove the header. dd if="WR1000_EU_92.122.2.4987.201806261618.bin" of="WR1000_EU_92.122.2.4987.201806261618.bin.mod" skip=8 bs=64 3) XOR the new file with the region key. FOR EU: 7B76741E67594351555042461D625F4545514B1B03050208000603020803000D FOR US: 7B76741E675943555D5442461D625F454555431F03050208000603060007010C You can use OpenWrt's tools/firmware-utils/src/xorimage.c tool for this: xorimage -i WR1000..bin.mod -o stock-firmware.bin -x -p 7B767.. Or, you can use this tool (CHANGE THE XOR KEY ACCORDINGLY!): https://gchq.github.io/CyberChef/#recipe=XOR(%7B'option':'Hex','string':''%7D,'',false) 4) Check the resulting decrypted image. Check if bytes from 0x20 to 0x3f are: 4C 69 6E 75 78 20 4B 65 72 6E 65 6C 20 49 6D 61 67 65 00 00 00 00 00 00 00 00 00 00 00 00 00 00 Alternatively, you can use u-boot's tool dumpimage tool to check if the decryption was successful. It should look like: # dumpimage -l stock-firmware.bin Image Name: Linux Kernel Image Created: Tue Jun 26 10:24:54 2018 Image Type: MIPS Linux Kernel Image (lzma compressed) Data Size: 4406635 Bytes = 4303.35 KiB = 4.20 MiB Load Address: 80000000 Entry Point: 8000c150 5) Flash it via forced firmware upgrade and don't "Keep Settings" CLI: sysupgrade -F -n stock-firmware.bin LuCI: make sure to click on the "Keep settings" checkbox to disable it. You'll need to do this !TWICE! because on the first try, LuCI will refuse the image and reset the "Keep settings" to enable. However a new "Force upgrade" checkbox will appear as well. Make sure to do this very carefully! Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added wifi compatible, spiffed-up the returned to stock instructions]
* ramips: add support for Telco Electronics X1Nicholas Smith2019-05-182-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621 DRAM: 256MB DDR3 Flash: 16MB SPI-NOR WiFi: 2.4GHz: MT7603 @ PCIe0 WiFi: 5.8GHz: MT7612 @ PCIe1 Modem: Sierra Wireless MC74xx Interfaces: GBE RJ45 x5 mPCIe x2 UART x1 I2C x1 JTAG x1 UIM x1 LEDs x6 Flash instructions: Flash from within the factory bootloader, firmware web interface or CLI using sysupgrade -F -n Signed-off-by: Nicholas Smith <mips171@icloud.com>
* ramips: add support for HILINK HLK-7628NLiu Yu2019-05-182-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 128 MB Flash: 32 MB WIFI: 802.11n/g/b 20/40 MHz Ethernet: 5 Port ethernet switch UART: 2x Flash instruction: The U-boot is based on Ralink SDK so we can flash the firmware using UART: 1. Configure PC with a static IP address and setup an TFTP server. 2. Put the firmware into the tftp directory. 3. Connect the UART0 line as described on the PCB. 4. Power up the device and press 2, follow the instruction to set device and tftp server IP address and input the firmware file name. U-boot will then load the firmware and write it into the flash. 5. After firmware is started connect via ethernet at 192.168.1.1 Signed-off-by: Liu Yu <f78fk@live.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [removed dupped subject]
* ramips: Add support for ZBT WE826-EKristian Evensen2019-05-173-1/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZBT WE826-E is a dual-SIM version of the ZBT WE826. The router has the following specifications: - MT7620A (580 MHz) - 128MB RAM - 32MB of flash (SPI NOR) - 5x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus) - 2x SIM card slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 10x LEDs (4 GPIO-controlled) - 1x reset button The following have been tested and working: - Ethernet switch - wifi - miniPCIe slot - USB port - microSD slot - sysupgrade - reset button Installation and recovery: In order to install OpenWRT the first time or recover the router, you can use the web-based recovery system. Keep the reset button pressed during boot and access 192.168.1.1 in your browser when your machine obtains an IP address. Upload the firmware to start the recovery process. How to swap SIMs: You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio13/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio14/value). Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: Add support for Head Weblink HDRM200Kristian Evensen2019-05-173-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Head Weblink HDRM200 is a dual-sim router based on MT7620A. The detailed specifications are: - MT7620A (580MHz) - 64MB RAM - 16MB of flash (SPI NOR) - 6x 10/100Mbps Ethernet (MT7620A built-in switch) - 1x microSD slot - 1x miniPCIe slot (only USB2.0 bus). Device is shipped with a SIMCOM SIM7100E LTE modem. - 2x SIM slots (standard size) - 1x USB2.0 port - 1x 2.4GHz wifi (rt2800) - 1x 5GHz wifi (mt7612) - 1x reset button - 1x WPS button - 3x GPIO-controllable LEDs - 1x 10 pin terminal block (RS232, RS485, 4 x GPIO) Tested: - Ethernet switch - Wifi - USB slot - SD card slot - miniPCIe-slot - sysupgrade - reset button Installation instructions: Installing OpenWRT for the first time requires a bit of work, as the board does not ship with OpenWRT. In addition, the bootloader automatically reboots when installing an image over tftp. In order to install OpenWRT on the HDRM200, you need to do the following: * Copy the initramfs-image to your tftp-root (default filename is test.bin) and configure networking accordingly (default server IP is 10.10.10.3, client 10.10.10.123). Start your tftp server. * Open the board and connect to UART. The pins are exposed and clearly marked. * Boot the board and press 1. * Either use the default filename and client/server IP-addresses, or specify your own. The image should now be loaded to memory and board boot. If the router reboots while the image is loading, you need to try again. Once the board has booted, copy the sysupgrade-image to the router and run sysupgrade in order to install OpenWRT to the flash. Notes: - You control which SIM slot to use by writing 0/1 to /sys/class/gpio/gpio0/value. In order for the change to take effect, you can either use AT-commands (AT+CFUN) or power-cycle the modem (write 0/1 to /sys/class/gpio/gpio21/value). - RS485 is available on /dev/ttyS0. - RS232 is available on /dev/ttyS1. - The name of the ioX-gpios map to the labels on the casing. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> [fixed whitespace issue and merge conflict in target.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Rakwireless RAK633Eike Feldmann2019-04-142-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's OEM module with 2*26 pin header, similar to LinkIt Smart 7688 or Vocore2. Specification: CPU: MT7628 580 MHz. MIPS 24K RAM: 64 MB Flash: 8 MB WIFI: 802.11n/g/b 20/40 MHz USB: 1x Port USB 2.0 Ethernet: 5 Port ethernet switch UART: 2x Installation: Use the installed uboot Bootloader. Connect a serial cable to serialport 0. Turn power on. Choose the option: "Load system code then write to Flash via TFTP". Choose the local device IP and the TFTP server IP and the file name of the system image. After if the Bootloader will copy the image to the local flash. Notes: The I2C Kernel module work not correctly. You can send and receive data. But the command i2cdetect doesn’t work. FS#845 Signed-off-by: Eike Feldmann <eike.feldmann@outlook.com> [commit subject and message touches, DTS whitespace fixes, wifi LED rename, pinctrl fixes, network settings fixes, lan/wmac mac addresses, removed i2c kernel modules] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for GL.iNet VIXMINIDavid Bauer2019-04-131-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: MediaTek MT7628NN RAM: 64M DDR2 (Etron EM68B16CWQD-25H) FLASH: 8M (Winbond W25Q64JVSIQ) LED: Power - WLAN BTN: Reset UART: 115200 8N1 TX and RX are labled on the board as pads next to the SoC Installation via web-interface ------------------------------ 1. Visit the web-interface at 192.168.8.1 Note: The ethernet port is by default WAN. So you need to connect to the router via WiFi 2. Navigate to the Update tab on the left side. 3. Select "Local Update" 4. Upload the OpenWrt sysupgrade image. Note: Make sure you select not to preserve the configuration. Installation via U-Boot ----------------------- 1. Hold down the reset button while powering on the device. Wait for the LED to flash 5 times. 2. Assign yourself a static IPv4 in 192.168.1.0/24 3. Upload the OpenWrt sysupgrade image at 192.168.1.1. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for Youku YK-L2Zhao Yu2019-04-061-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware spec: CPU: MTK MT7621A RAM: 256MB ROM: 16MB SPI Flash WiFi: MT7603EN + MT7612EN Button: 2 buttons (reset, wps) LED: 8 LEDs (Power 2G 5G WPS Internet LAN1 LAN2 USB) Ethernet: 3 ports, 2 LAN + 1 WAN Other: USB3.0 Flashing instructions: Visit the openwrt forum topic for this router: https://forum.openwrt.org/t/add-openwrt-support-for-youku-yk-l2/34692 to get the bootloader and unlock firmware. 0. upgrade your router with the telnet firmware via the firmware upgrade page on the webui. 1. telnet 192.168.11.1 from your PC 2. Download the pb-boot-youku_l2-20190317-61b6d33.bin and transfer it to the /tmp directory of the router. 3. mtd write /tmp/pb-boot-youku_l2-20190317-61b6d33.bin Bootloader 4. turn off the power 5. Push the reset button while turning on the router and wait until LED start blinking (~10sec.) 6. Connect Ethernet port and goto http://192.168.1.1. 7. Upload the firmware to firmware restore page in webui. Signed-off-by: Zhao Yu <574249312@qq.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [rewrote the flashing instructions, fixed author]
* ramips: add Netgear EX6150David Bauer2019-03-291-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621 RAM: 64M (Winbond W9751G6KB-25) FLASH: 16MB (Macronix MX25L12835F) WiFi: MediaTek MT7662E bgn 2SS WiFi: MediaTek MT7662E nac 2SS BTN: ON/OFF - Reset - WPS - AP/Extender toggle LED: - Arrow Right (blue) - Arrow Left (blue) - WiFi 1 (red/green) - WiFi 2 (red/green) - Power (green/amber) - WPS (Green) UART: UART is present as Pads on the backside of the PCB. They are located on the other side of the Ethernet port. 3.3V - GND - TX - RX / 57600-8N1 3.3V is the nearest one to the antenna connectors Installation ------------ Update the factory image via the Netgear web-interfaces (by default: 192.168.1.250/24). You can also use the factory image with the nmrpflash tool. For more information see https://github.com/jclehner/nmrpflash Signed-off-by: David Bauer <mail@david-bauer.net> [merge conflict in 02_network, flash@0 node rename, wlan DTS triggers] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for ZyXEL Keenetic StartVladimir Kot2019-03-292-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: RT5350F - CPU Frequency: 360 MHz - Flash Chip: Winbond 25Q32 (4096 KiB) - RAM: 32768 KiB - 5x 10/100 Mbps Ethernet (4x LAN, 1x WAN) - 1x external, non-detachable antenna - UART (J1) header on PCB (57800 8n1) - Wireless: SoC-intergated: 2.4GHz 802.11bgn - USB: None - 3x LED, 2x button Flash instruction: 1. Configure PC with static IP 192.168.1.2/24 and start TFTP server. 2. Rename "openwrt-ramips-rt305x-kn_st-squashfs-sysupgrade.bin" to "kstart_recovery.bin" and place it in TFTP server directory. 3. Connect PC with one of LAN ports, press the reset button, power up the router and keep button pressed until power LED start blinking. 4. Router will download file from TFTP server, write it to flash and reboot. Signed-off-by: Vladimir Kot <vova28rus@gmail.com> [fixed git commit author and whitespace issues in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for WIZnet WizFi630S boardTobias Welz2019-03-291-0/+4
| | | | | | | | | | | | | | | | | | | | The WIZnet WizFi630S board is in the miniPCIe form factor. SoC: Mediatek MT7688AN RAM: 128MB Flash: 32Mb WiFi: 2.4GHz Ethernet: 3x 100Mbit USB: 1 (USB 2.0) serial ports: 2 (1x full, 1xlite) Flash and recovery instructions: Use the factory installed u-boot boot loader. It is available on UART2 (115200,8,n,1). Then get the sysupgrade image from a tftp server. Signed-off-by: Tobias Welz <tw@wiznet.eu> [whitespace and device name in makefile fixes] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for DLINK DIR-510LPawel Dembicki2019-03-243-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The DIR-510L Wireless Router are based on the MT7620A SoC. Specification: -MediaTek MT7620A (580 Mhz) -128 MB of RAM -16 MB of FLASH -802.11bgn radio -1x 10/100 Mbps Ethernet -2x internal, non-detachable antennas -UART (J3) header on PCB (57600 8n1) -1x bi-color LED (GPIO-controlled), 2x button -JBOOT bootloader Known issues: -Ethernet port is used as LAN -No communication with charger IC. (uart bitbang needed) Installation: Apply factory image via d-link http web-gui. How to revert to OEM firmware: 1.) Push the reset button and turn on the power. Wait until LED start blinking (~10sec.) 2.) Upload original factory image via JBOOT http (IP: 192.168.123.254) 3.) If http doesn't work, it can be done with curl command: curl -F FN=@XXXXX.bin http://192.168.123.254/upg where XXXXX.bin is name of firmware file. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [fixed whitespace issue in 10-rt2x00-eeprom] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: Speed up eeprom read/writeAdrian Schmutzler2019-03-211-2/+2
| | | | | | | | | | | | | | Reading and writing to and from flash storage is slowed down enormously by some functions which use a block size of 1. This patch reworks the extraction scripts to be much faster and efficient by reading and writing in possibly one big block. This is based on the initial commit a69e101 for ipq40xx by Christian Lamparter <chunkeey@gmail.com>. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Rosen Penev <rosenp@gmail.com>
* ramips: Xiaomi MIR3G: detect board name from DTSOzgur Can Leonard2019-03-214-23/+20
| | | | | | | | | | | | | | | | - Former "mir3g" board name becomes "xiaomi,mir3g". - Reorder some entries to maintain alphabetical order. - Change DTS so status LEDs (yellow/red/blue) mimic Xiaomi stock firmware: (Section Indicator) <http://files.xiaomi-mi.co.uk/files/router_pro/router%20PRO%20EN.pdf> <http://files.xiaomi-mi.co.uk/files/Mi_WiFi_router_3/MiWiFi_router3_EN.pdf> |Yellow: Update (LED flickering), the launch of the system (steady light); |Blue: during normal operation (steady light); |Red: Safe mode (display flicker), system failure (steady light); Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> [Added link to similar Router 3 model] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ramips: add support for I-O DATA WN-AC733GR3INAGAKI Hiroshi2019-03-212-3/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WN-AC733GR3 is a 2.4/5 GHz band 11ac router, based on MediaTek MT7620A. Specification - SoC : MediaTek MT7620A - RAM : DDR2 64 MiB - Flash : SPI-NOR 8 MiB - WLAN : 2.4/5 GHz - 2.4 GHz : MT7620A (SoC), 2T2R - 5 GHz : MT7610E, 1T1R - Ethernet : 10/100/1000 Mbps (RTL8367RB) - LED/key : 4x/4x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from LED side - 57600n8 Flash instruction using factory image: 1. Boot WN-AC733GR3 normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for Xiaomi Mi Router 3 ProOzgur Can Leonard2019-03-133-2/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: CPU: MediaTek MT7621AT (2x880MHz) RAM: 512MB DDR3 FLASH: 256MB NAND WiFi: 2.4GHz 4x4 MT7615 b/g/n (Needs driver, See Issues!) WiFI: 5GHz 4x4 MT7615 a/n/ac (Needs driver, See Issues!) USB: 1x 3.0 ETH: 1x WAN 10/100/1000 3x LAN 10/100/1000 LED: Power/Status BTN: RESET UART: 115200 8n1 Partition layout and boot: Stock Xiaomi firmware has the MTD split into (among others) - kernel0 (@0x200000) - kernel1 (@0x600000) - rootfs0 - rootfs1 - overlay (ubi) Xiaomi uboot expects to find kernels at 0x200000 & 0x600000 referred to as system 1 & system 2 respectively. a kernel is considered suitable for handing control over if its linux magic number exists & uImage CRC are correct. If either of those conditions fail, a matching sys'n'_fail flag is set in uboot env & a restart performed in the hope that the alternate kernel is okay. If neither kernel checksums ok and both are marked failed, system 2 is booted anyway. Note uboot's tftp flash install writes the transferred image to both kernel partitions. Installation: Similar to the Xiaomi MIR3G, we keep stock Xiaomi firmware in kernel0 for ease of recovery, and install OpenWRT into kernel1 and after. The installation file for OpenWRT is a *squashfs-factory.bin file that contains the kernel and a ubi partition. This is flashed as follows: nvram set flag_try_sys1_failed=1 nvram set flag_try_sys2_failed=0 nvram commit dd if=factory.bin bs=1M count=4 | mtd write - kernel1 dd if=factory.bin bs=1M skip=4 | mtd write - rootfs0 reboot Reverting to stock: The part of stock firmware we've kept in kernel0 allows us to run stock recovery, which will re-flash stock firmware from a *.bin file on a USB. For this we do the following: fw_setenv flag_try_sys1_failed 0 fw_setenv flag_try_sys2_failed 1 reboot After reboot the LED status light will blink red, at which point pressing the 'reset' button will cause stock firmware to be installed from USB. Issues: OpenWRT currently does not have support for the MT7615 wifi chips. There is ongoing work to add mt7615 support to the open source mt76 driver. Until that support is in place, there are closed-source kernel modules that can be used. See: https://forum.openwrt.org/t/support-for-xiaomi-wifi-r3p-pro/20290/170 Signed-off-by: Ozgur Can Leonard <ozgurcan@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [02_network remaps, Added link to notes]
* ramips: add support for ALFA Network Tube-E4GPiotr Dymacz2019-03-112-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network Tube-E4G is an outdoor, dual-SIM LTE Cat. 4 CPE, based on MediaTek MT7620A, equipped with Quectel EC25 miniPCIe modem. Specification: - MT7620A (580 MHz) - 64/128/256 MB of RAM (DDR2) - 16/32 MB of flash (SPI NOR) - 1x 10/100 Mbps Ethernet, with passive PoE support (24 V) - 1x miniPCIe slot (with PCIe and USB 2.0 buses) - 2x SIM slot (mini, micro) with detect and switch driven by GPIO - 1x detachable antenna (modem main) - 1x internal antenna (modem div) - 1x GPS passive antenna (optional) - 5x LED (all driven by GPIO) - 1x button (reset) - UART (4-pin, 2.54 mm pitch) header on PCB Other: Default SIM slot is selected at an early stage by U-Boot, based on 'default_sim' environment value: 1 or unset = SIM1 (mini), 2 = SIM2 (micro). U-Boot also resets the modem, using #PERST signal, before starting kernel. Flash instruction: You can use the 'sysupgrade' image directly in vendor firmware which is based on OpenWrt (make sure to not preserve settings - use 'sysupgrade -n -F ...' command). Alternatively, use web recovery mode in U-Boot: 1. Power the device with reset button pressed, the LAN LED will start blinking slowly and after ~3 seconds, when it starts blinking faster, you can release the button. 2. Setup static IP 192.168.1.2/24 on your PC. 3. Go to 192.168.1.1 in browser and upload 'sysupgrade' image. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ramips: rework network settings for HC5861Chen Minqiang2019-03-061-1/+4
| | | | | | | dts: disable port4 and leave it ephy mode because it connect to nothing switch port5 connected to GE port we use it as wan port Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: add support for Belkin F9K1109v1Kip Porterfield2019-03-022-0/+9
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specification: - SoC: Ralink RT3883 (MIPS 74Kc) 500Mhz - RAM: 64Mb - Flash: 8MB (SPI-NOR) - Ethernet: 10/100/1000 Mbps - WLAN Wireless 1: SoC-integrated : 2.4/5 GHz Wireless 2: 2.4 GHz RT3092L - LED: 2x USB, WAN, LAN - Key: WPS, reset - Serial: 4-pin header, (57600,8,N,1), 3.3V TTL, GND, RX, TX, V - J12 marking on board - USB ports: 2 x USB 2.0 Flashing instructions: Option 1 (from bootloader web) - Hold reset button on the back of router when plugging in power (for at-least 10 seconds after plugged in) - Connect to a Lan port - Set computer IP to 10.10.10.3 - Go to http://10.10.10.123 in a web browser - Click the Browse... Button and select the *squashfs.sysupgrade.bin file then click APPLY Option 2 (from the stock admin web) - Go to firmware upgrade - Upload the **factory** image *initramfs.bin first - Boot into openwrt - From Luci web in openwrt upload the *squashfs.sysupgrade.bin Signed-off-by: Kip Porterfield <kip.porterfield@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added v1 to the compatible identifier, added pciid for the RT3092L, fixed pci unit-address, split out the F9K110X.dtsi to prepare for a possible F9K1103 patch]
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-30 23:39:10 +0000