aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files/etc/diag.sh
Commit message (Collapse)AuthorAgeFilesLines
* ramips: Support for RAMIPS based Tripmate HT-TM02 boardJohn Crispin2014-10-061-0/+3
| | | | | | | | | | | | Provides support for the Tripmate HT-TM02 personal router including LEDs and reset button. “Mode” switch is not supported. New profile includes full set of packages required to enable LEDs, USB, and LUCI. Patches were applied against trunk snapshot r42649. Functionality has been tested in AP, basic wifi client, wifi router, and routed client modes - all good. Signed-off-by: Ron Curry <wingspinner@gmail.com> SVN-Revision: 42785
* ramips: Hame: change LED name mpr-x -> hameJohn Crispin2014-08-181-2/+2
| | | | | | Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 42190
* ramips:support Lenovo AC1200 Wireless routerJohn Crispin2014-08-031-0/+4
| | | | | | | | | Lenovo AC1200 series has two types, Y1 and Y1S. Y1S has 256MB DDR2, Y1 only has 128MB and Y1 have no Giga Port. Signed-off-by: Lintel <lintel.huang@gmail.com> SVN-Revision: 41961
* ramips: Add support for VoCoreJohn Crispin2014-08-011-0/+3
| | | | | | | | | This is based and tested on VoCore Alpha, but other stuff like status/eth LEDs are present on the final board revision + VoDock. All GPIOs are exported, except spi/i2c. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> SVN-Revision: 41939
* ramips: Fix LEDs on the Kingston MLW221John Crispin2014-08-011-1/+1
| | | | | | | | | | LED Fix up for the Kingston Mobilelite Wireless (MLW-221) http://wiki.openwrt.org/toh/kingston/mlw221 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 41933
* ramips: add support for Kingston MLW221John Crispin2014-07-261-0/+3
| | | | | | | | | | This patch adds support for the Kingston Mobilelite Wireless (MLW-221) http://wiki.openwrt.org/toh/kingston/mlw221 Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 41841
* ramips: add support for WR8305RT boardJohn Crispin2014-07-121-0/+3
| | | | | | | Signed-off-by: Jorge Vargas <jorge.vargas@sosvia.com> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41584
* ramips: add asiarf awapn2403 supportJohn Crispin2014-06-131-0/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41177
* ralink: Add support for samsung cy-swr1100 wireless routerJohn Crispin2014-06-021-0/+3
| | | | | | | | | | | | It is base on rt3662 soc with dual band 802.11n wireless router. Use rtl8367R switch chip. This patch adds a profile for this board. It use seama image header. so i also enable it on kernel config. Signed-off-by: michael lee <igvtee@gmail.com> SVN-Revision: 40908
* ramips: Support for Teltonika RUT5XXJohn Crispin2014-06-021-0/+3
| | | | | | | | | | | | Hi Hartmut, Thanks for your feedback, I have reformated the patch accordingly. Added support for Teltonika RUT5XX hardware. Signed-off-by: Steffen Weinreich <steve@weinreich.org> SVN-Revision: 40907
* ramips: Add support for the 7Links PX-4885 wireless router.John Crispin2014-04-221-0/+3
| | | | | | | | | | | | | The 7Links PX-4885 is a small battery-powered wireless router. It is based on a RT5350F WiSoC and features one ethernet port and one USB port. It is a Hame MPR-A1 clone, except it has different GPIOs, a different battery and more RAM (32 MB). This patch adds a profile for this board, the corresponding device tree file and the adequate base-files changes (incl. sysupgrade). Signed-off-by: Hugo Grostabussiat <bonstra@bonstra.fr.eu.org> SVN-Revision: 40554
* ramips: add Airlink101 AR725W userland supportJohn Crispin2014-04-221-0/+3
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 40550
* ralink: add support for na930John Crispin2014-02-181-1/+4
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 39611
* ramips: Add userspace support for the Edimax BR-6475nDJohn Crispin2014-01-151-1/+1
| | | | | | | | | The rt2x00 wifi driver may still need updating to function with this device. Signed-off-by: Christopher Lais <chris+openwrt@zenthought.org> SVN-Revision: 39298
* ralink: add HLK-RM04 supportJohn Crispin2014-01-121-0/+3
| | | | | | | | https://github.com/JiapengLi/OpenWrt-HiLink-HLK-RM04 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 39237
* ralink: add mt7620n supportJohn Crispin2013-11-161-3/+2
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38823
* ralink: add support for 2 new mt7620 boards made by buffaloJohn Crispin2013-10-281-0/+6
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38550
* ralink: add support for dalink dcs930l ipcamJohn Crispin2013-09-191-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38053
* ralink: DIR-300 B7 and DIR-320/NRU B1 on Ralink RT5350John Crispin2013-09-181-1/+1
| | | | | | | | https://dev.openwrt.org/ticket/14129 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38040
* ramips: DIR-610-A1 SupportJohn Crispin2013-08-141-1/+1
| | | | | | | | http://patchwork.openwrt.org/patch/3933/ Signed-off-by: Flavio Silveira <fggs@terra.com.br> SVN-Revision: 37785
* ramips: add Poray IP2202 supportJohn Crispin2013-08-011-0/+3
| | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 37640
* ramips: add Poray X8 supportJohn Crispin2013-08-011-0/+3
| | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 37639
* ramips: add Poray X5/X6 SupportJohn Crispin2013-08-011-0/+3
| | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 37638
* ramips: add Poray M4 4M/8M supportJohn Crispin2013-08-011-0/+3
| | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 37637
* ramips: add Poray M3 supportJohn Crispin2013-08-011-0/+3
| | | | | | Signed-off-by: Felix Kaechele <heffer@fedoraproject.org> SVN-Revision: 37636
* ramips: add MPR-A1 supportJohn Crispin2013-07-271-0/+3
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 37568
* base-files: diag does not need to insmod any drivers, procd already did it ↵John Crispin2013-06-211-1/+0
| | | | | | | | for us Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36999
* ramips: add HAME MPR-A2 supportJohn Crispin2013-06-101-0/+3
| | | | | | | | | | This patch adds support for HAME MPR-A2 router using a DTS file. The platform is Ralink RT5350. http://wiki.openwrt.org/toh/hame/mpr-a2 Signed-off-by: Dmitry Shmygov <shmygov@rambler.ru> SVN-Revision: 36898
* ramips: add support for belkin F7C027 wemo/homeautomatisation plugJohn Crispin2013-06-101-0/+3
| | | | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 36897
* ramips: Add Alpha ASL-26555 support.John Crispin2013-04-251-0/+3
| | | | | | | | | | | | | | | | This board uses a TrendChip SOC with its own RAM/Flash for ADSL support. We know both SOCs are connected through ethernet and use some kind of protocol for UART communication, but due to the lack of GPL sources we couldn't get it to work. For this reason the network is configured only for LAN. There are two versions (Chile 8MB and Spain 16MB). Wiki: http://wiki.openwrt.org/toh/alpha/asl26555 Signed-off-by: Esteban Benito <estebanjbs@gmail.com> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com> Patchwork: http://patchwork.openwrt.org/patch/3571/ Acked-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36433
* ramips: Add support of D-link DIR-620D1John Crispin2013-04-251-1/+1
| | | | | | | Signed-off-by: Serge Vasilugin <vasilugin@yandex.ru> Acked-by: John Crispin <blogic@openwrt.org> SVN-Revision: 36432
* Add Netgear WNCE2001 (OF version)John Crispin2013-04-091-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add Netgear WNCE2001. This is a small RT3052 device with 4MB spi flash and 32MB ram. 2 built-in antennas, 1x fastE, no USB, reset & wps switch. On my model the AP/RT switch is unpopulated, but I verified the gpio mapping for it. The stock firmware is running an unprotected tftpd which allows you to read any file from the filesystem. Serial port is present on testpads (See image on the wiki page). There are more testpads below the shield near the SoC, which may have JTAG. Slight annoyance: The bootloader is checksumming kernel&rootfs, but can be tricked by zeroing checksum and length fields in the checksum partition, see target/linux/ramips/base-files/lib/preinit/04_disable_wnce2001_flash_checksumming The manufacturer image is very similar to the DAP one, so I slightly modified mkdapimg to support generating it. The resulting openwrt-ramips-rt305x-wnce2001-squashfs-factory-(worldwide|northamerica).bin can be used to flash from stock to OpenWRT using the stock firmware upgrade function, without using the serial port. http://www.netgear.com/landing/wnce2001.aspx http://wiki.openwrt.org/toh/netgear/wnce2001 Signed-off-by: Tobias Diedrich <ranma+openwrt@tdiedrich.de> SVN-Revision: 36289
* add profile for tenda w150m boardJohn Crispin2013-04-031-1/+1
| | | | | | | | http://patchwork.openwrt.org/patch/3371/ Signed-off-by: Chi Zhang <zhangchi866@gmail.com> SVN-Revision: 36176
* add Huawei D105John Crispin2013-04-031-0/+3
| | | | | | | | http://patchwork.openwrt.org/patch/3510/ Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 36173
* make sure errors get sent to /dev/nullJohn Crispin2013-03-121-1/+1
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 35988
* ramips: add user-space support for the Upvel UR-326N4G boardGabor Juhos2013-03-111-0/+3
| | | | | | | | | [juhosg: fix mac address setup] Patch from: Дмитрий Лебедев <lebedev@trendnet.ru> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35971
* ramips: migrate to common led helper functionsGabor Juhos2013-02-181-28/+4
| | | | | | | | | [juhosg: migrate to status_led_blink_{preinit,failsafe} helpers] Signed-off-by: Michael Heimpold <mhei@heimpold.de> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35652
* ramips: add user-space support for the Omnima EMB HPM boardGabor Juhos2013-02-021-1/+2
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35467
* ramips: add userspace support for the Edimax BR-6425Gabor Juhos2013-02-021-0/+3
| | | | | | | | | [juhosg: remove sysupgrade changes] Signed-off-by: Yuval Adam <yuv.adm@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35463
* ramips: add user-space support for the Tenda 3G300MGabor Juhos2013-01-191-0/+3
| | | | | | | Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 35245
* adds support for Edimax BR-6524NJohn Crispin2013-01-061-0/+3
| | | | | | | | fixes #12754 Signed-off-by: <rq@akl.lt> SVN-Revision: 35020
* ramips: add user-space support for the Planex MZK-W300NH2 RouterGabor Juhos2012-12-291-0/+3
| | | | | | | | Signed-off-by: Samir Ibradžić <sibradzic@gmail.com> Patchwork: http://patchwork.openwrt.org/patch/3077/ Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 34926
* ramips: rt305x: add user-space support for the Asus RT-N13UGabor Juhos2012-11-291-0/+3
| | | | | | | Signed-off-by: Amit Mendapara <mendapara.amit@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 34406
* ramips: add DIR-615 D userspace supportGabor Juhos2012-11-251-1/+1
| | | | | | | | | | | | | | | Commit 7c8edac25f23c4fc14239fdc293caa1317649944 introduced new machine and Makefile changes to build images for this target. However, without the userspace bits a ramips machine can't use wifi as the necessary "eeprom" data is to be extracted by a hotplug script; also, sysupgrade support and default led configuration are missing. An IRC user reported these changes allowed him to use wifi on his hardware. Signed-off-by: Paul Fertser <fercerpav@gmail.com> Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 34331
* ramips: add user-space support for TEW-691GRGabor Juhos2012-10-181-0/+1
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 33851
* ramips: add user-space support for the TEW-692GR boardGabor Juhos2012-10-181-0/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 33847
* ramips: add user space support for the DIR-645Gabor Juhos2012-10-181-0/+3
| | | | | | Signed-off-by: Gabor Juhos <juhosg@openwrt.org> SVN-Revision: 33844
* ramips: add board alias for the ALL0239-3GGabor Juhos2012-08-171-0/+1
| | | | | | | | | | | | | | Generate image for the ALL0239-3G which can be flashed through the chipset-vendor SDK based firmware's web-interface and bootloader. The bootloader seems to ignore uImage checksum errors, but does complain about them once the 0xDEADC0DE was replaced by an actual JFFS2 page. I'm working on implementing fixtrx for uImage in the mtd package to solve this. Signed-off-by: Daniel Golle <dgolle@allnet.de> SVN-Revision: 33206
* ramips: add support for D-Link DIR-615 H1Gabor Juhos2012-08-171-1/+1
| | | | | | | | | | | | rt2x00 still needs some patching as the radio doesn't come to life. Installation via webflash. [juhosg: fix whitespace issues, remove rt305x_register_usb from machine setup because the board has no USB port] Signed-off-by: Mikko Hissa <mikko.hissa@uta.fi> SVN-Revision: 33205
* ramips: add D-Link DIR-620 A1 supportGabor Juhos2012-08-121-1/+1
| | | | | | | | | | | | Full functionality runtime tested, installation via OEM web-interface requires a follow-up patch. Thanks go to Sergey Vasilyugin for his patch that pointed me at the missing bits (including the antiparallel wps led). Signed-off-by: Paul Fertser <fercerpav@gmail.com> SVN-Revision: 33142
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 10:35:59 +0000