aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files/etc/board.d
Commit message (Collapse)AuthorAgeFilesLines
* ramips: initialize youhua, wr1200js WAN MAC addresses from flashAdrian Schmutzler2019-09-251-0/+1
| | | | | | | | | This patch changes wan MAC address setup for youhua,wr1200js from retrieving it by calculation to reading it from flash. This has been checked on-device. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for I-O DATA WNPR2600GINAGAKI Hiroshi2019-09-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | I-O DATA WNPR2600G is a 2.4/5 GHz band 11ac router, based on MediaTek MT7621A. Specification: - SoC : MediaTek MT7621A - RAM : DDR3 128 MiB - Flash : SPI-NOR 16 MiB - WLAN : 2.4/5 GHz 4T4R - 2.4 GHz : MediaTek MT7615 - 5 GHz : MediaTek MT7615 - Ethernet : 10/100/1000 Mbps - Switch : MT7530 (SoC) - LED/keys : 4x/3x (2x buttons, 1x slide-switch) - UART : through-hole on PCB - J1: Vcc, RX, GND, TX from SoC side - 57600n8 Flash instruction using factory image: 1. Boot WNPR2600G normaly 2. Access to "http://192.168.0.1/" and open firmware update page ("ファームウェア") 3. Select the OpenWrt factory image and click update ("更新") button to perform firmware update 4. Wait ~150 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: replace MAC address configuration for I-O DATA WN-AC-GR devicesINAGAKI Hiroshi2019-09-251-1/+1
| | | | | | | | | | | | | following I-O DATA devices have a MAC address as "wanaddr" for WAN interface in u-boot-env: - WN-AC1167GR - WN-AC733GR3 I replaced MAC address configuration in these devices to omit address calculation in 02_network. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ramips: add support for ipTIME A3Sungbo Eo2019-09-251-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A3 is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 3x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ramips: add support for XiaoYu XY-C5Qi Jiang2019-09-251-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | Hardware: SoC: MT7621A Flash: 32 MiB RAM: 512 MiB Ethernet: built-in switch USB: 1x USB3.0 SATA: ASM1060, 1 SATA port Flash instruction (TFTP): 1. Set PC to fixed ip address 192.168.173.22 2. Download *-sysupgrade.bin image and rename it to firmware.img 3. Start a tftp server with the image file in its root directory 4. Turn off the router 5. Turn on router,press the reset button and wait ~15 seconds 6. Release the reset button and after a short time the firmware should be transferred from the tftp server 7. Wait ~3 minutes to complete recovery. Signed-off-by: Qi Jiang <rushx@live.cn> [squash commits, add label-mac-device, fix sign-off style] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: replace backticks by $(...)Adrian Schmutzler2019-09-211-3/+3
| | | | | | | | | This replaces deprecated backticks by more versatile $(...) syntax. While at it, remove some useless cat commands and deprecated egrep commands. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for EnGenius ESR600Nick Briggs2019-09-202-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The EnGenius ESR600 is a dual band wireless router with a 4-port gigabit Ethernet switch, a gigabit Ethernet WAN port and a USB port. Specification: - Bootloader: U-Boot - SoC: MediaTek MT7620A (600 MHz) - Flash: 16MB, Macronix MX25L12845E - RAM: 64MB, Nanya NT5TU32M16DG-AC - Serial: 115200 baud, no header, 3.3V J2: Vcc (arrow), Gnd, Tx, Rx - USB: USB 2, 5V - Ethernet: 5 x 1 Gb/s 4 LAN 1 WAN, Atheros AR8327 - WiFi0: 5 GHz 802.11 b/g/n Ralink RT5592N 300 Mb/s, 2T2R - WiFi1: 2.4 GHz 802.11 b/g/n integrated 300 Mb/s, 2T2R - Antennas: 2 per radio, internal - LEDs: 1 programmable power (amber) 2 programable radio (blue) 1 programable WPS-5G (blue) 1 non-programable WAN activity (blue) 1 unconfigured WPS-2.4G (amber) - Buttons: GPIO: Reset, WPS Installation: Use the OEM web interface to install the ...-factory.dlf image. Use the OpenWRT ...-sysupgrade.bin image for future upgrades. The J2 serial port can be accessed either by soldering in a header, standard 0.1" spacing, or by using pogo-pins against the back side. As configured by the OEM, the U-Boot boot delay is short, however quickly typing "1" leads to the U-Boot "System load Linux to SDRAM via TFTP" prompt. The TFTP client is configured by default with client: 192.168.99.9 server: 192.168.99.8 filename: uImageESR600 It will load an OpenWRT initramfs kernel with this method. Known issues: 1) Only the ports externally labeled WAN, LAN3 and LAN4 are operational. LAN1 and LAN2 do not appear to power up. This issue is also present in the Lava LR25G001. 2) The amber WPS-2.4G LED, in the same lightguide as the blue WPS-5G LED, is not configured in the Device Tree specification. 3) The blue WAN activity LED is not configured in the Device Tree specification as this causes the AR8327 switch to fail to initialize. Signed-off-by: Nick Briggs <nicholas.h.briggs@gmail.com> [merge conflict in 02_network] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: mt7621: Add new device AsiaRF AP7621-NV1Daniel Danzberger2019-09-201-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Mediatek MT7621A CPU: 4x 880Mhz Cache: 32 KB I-Cache and 32 KB D-Cach 256 KB L2 Cache (shared by Dual-Core) RAM: DDR3 512MB 16bits BUS FLASH: 16MB Switch: Mediatek Gigabit Switch (2 x LAN, 1 x WAN) POE: (1x PD, 2x PSE) USB: 1x 3.0 PCI: 3x Mini PCIe (3 USB2.0 + 2 x UIM interface) GPS: Quectel L70B SIM: 2 Slots BTN: Reset LED: - Power - Ethernet - Wifi - USB UART: UART is present as Pads with throughholes on the PCB. They are located on left side. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ The stock image is a modified openwrt and can be overflashed via sysupgrade -F Signed-off-by: Daniel Danzberger <daniel@dd-wrt.com> [merge conflict in mt7621.mk] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Asus RT-AC85PBirger Koblitz2019-09-201-11/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Winbond W632GG6KB-1) FLASH: 128MB (Macronix MX30LF1G18AC-TI) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x USB 3.1 (Gen 1) BTN: Reset, WPS LED: - Power (blue) - 5Ghz (blue) - 2.4GHz (blue) - Internet (blue) - 4x LAN (blue) (LAN/WAN leds are not controllable by GPIOs) UART: UART is present as Pads marked J4 on the PCB. 3.3V - TX - RX - GND / 57600-8N1 3.3V is the square pad MAC: The MAC address on the router-label matches the MAC of the 2.4 GHz WiFi. LAN and WAN MAC are identical: MAC_LABEL+4 5 GHz WiFi MAC: also MAC_LABEL+4 Installation ------------ Via U-Boot tftpd: Switch on device, within 2s press reset button and keep pressed until power LED starts blinking slowly. Upload factory image via tftp put, the router's ip is 192.168.1.1 and expects the client on 192.168.1.75. The images also work on the Asus RT-AC65P models as tested by Gabor. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> Tested-by: Gabor Varga <vargagab@gmail.com> [fixed Asus -> ASUS in DTS] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: add support for Edimax RG21SBirger Koblitz2019-09-201-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT dual-core @ 880MHz RAM: 256M (Nanya NT5CC128M) FLASH: 16MB (Macronix MX25L12835F) WiFi: - 2.4GHz MediaTek MT7615N bgn - 5GHz MediaTek MT7615N nac Switch: SoC integrated Gigabit Switch (4 x LAN, 1 x WAN) USB: No BTN: Reset, WPS LED: 4 red LEDs, indistinguishable when casing closed UART: UART is present as Pads marked J1 on the PCB. 3.3V - RX - GND - TX / 57600-8N1 3.3V is the square pad Installation ------------ Update the factory image via the OEM web-interface (by default:http://192.168.1.1) The sysupgrade image can be installed via TFTP from the U-Boot bootloader. Connect ethernet port 2. Signed-off-by: Birger Koblitz <mail@birger-koblitz.de> [flash node rename, EDIMAX -> Edimax, complete device model name] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: provide label MAC addressAdrian Schmutzler2019-09-191-4/+32
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds the label MAC address for several devices in ramips. Some devices require setting the MAC address in 02_network: For the following devices, the netif device can be linked in device tree, but the MAC address cannot be read: - cudy,wr1000 - dlink,dir-615-d - dlink,dir-615-h1 - dlink,dir-860l-b1 - glinet,gl-mt300a - glinet,gl-mt300n - glinet,gl-mt750 - vocore,vocore2 - vocore,vocore2-lite - zbtlink,zbt-we1326 - zbtlink,zbt-wg3526 For the following devices, label MAC address is tied to lan or wan, so no node to link to exists in device tree: - dlink,dir-510l - dlink,dwr-116-a1 - dlink,dwr-118-a1 - dlink,dwr-118-a2 - dlink,dwr-921-c1 - dlink,dwr-922-e2 - all hiwifi devices - lava,lr-25g001 - xiaomi,mir3p Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: fix MAC address setup for Newifi Y1 and Y1SAdrian Schmutzler2019-09-071-2/+2
| | | | | | | | | | | | | | | | | | | | | | | So far, MAC address setup for those devices has been using local addresses although additional MAC addresses are available on flash. On device, we found the following situation: position Y1 Y1S 0x4 *:d4 *:e4 0x8004 *:d6 *:e8 0x28 *:d4 *:e4 0x2e *:d7 *:eb Since 0x4 and 0x28 yield the same address, the former was set for &ethernet in DTS. However, the typical location on this architecture is 0x28, so this patch changes that. For further setup in 02_network, the local bit for lan_mac is removed, so the address from &ethernet is used at all. For wan_mac, instead of calculating an address with local bit set, this patch exploits the previously unused address in 0x2e. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: initialize MAC addresses from flash where possibleAdrian Schmutzler2019-09-071-5/+9
| | | | | | | | | | | | This patch changes wan MAC address setup from retrieving it by calculation to reading it from flash. Changes are limited to cases where on-device check was possible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [fix mac for newifi-d1; drop adslr,g7 because it's unlikely for vendor to specifically use 2.4g mac as wan_mac] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix duplicate network setup for dlink,dir-615-h1Adrian Schmutzler2019-09-071-1/+0
| | | | | | | | | | | | | | In 555ca422d1cb ("ramips: fix D-Link DIR-615 H1 switch port mapping"), port setup for dir-615-h1 was changed without removing the old one. This was working as the new one was triggered earlier than the old one. (In the meantine, changed sorting during ramips rename patches actually inversed that order.) Anyway, just remove the wrong case now. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: remove duplicate case for MAC setup of freestation5Adrian Schmutzler2019-09-071-1/+0
| | | | | | | | | | | | ARC FreeStation5 is present twice in MAC address setup. From older commits/changes, it is not possible to reconstruct the correct choice only by reading the annotations. Thus, remove the second case and keep the first one, so behavior stays the same (as nobody seems to have complained about it). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: clean and improve MAC address setup in 02_networkAdrian Schmutzler2019-09-071-28/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch removes unnecessary MAC address setup statements in ramips' 02_network by doing several optimizations: 1. For the following devices, lan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The lan_mac statement is removed in 02_network, but wan_mac is kept: - mercury,mac1200r-v2 - phicomm,k2g - skylab,skw92a - wiznet,wizfi630a 2. For the following devices, wan_mac was set up with mtd_get_mac_binary although the same address was set in DTS. The wan_mac statement is removed in 02_network, no lan_mac is present: - buffalo,whr-g300n - glinet,gl-mt300n-v2 - zyxel,keenetic-start 3. For the following device, lan_mac and wan_mac were set up with mtd_get_mac_binary to the same address as set in DTS. Both statements are removed in 02_network: - buffalo,whr-600d 4. For some devices, it was possible to move setup from 02_network to DTS by introducing previously missing mtd_mac_address: - buffalo,whr-1166d - buffalo,whr-300hp2 - buffalo,wsr-600dhp - ohyeah,oy-0001 - planex,vr500 5. For one device, mtd_mac_address was just wrong and overwritten by 02_network. Put the correct value in DTS and remove redundant statement in 02_network: - asus,rt-ac57u 6. For one device, MAC address defined in DTS is exchanged together with lan_mac/wan_mac setup in 02_network, so that cases in 02_network can be merged: - phicomm,k2p For some devices, an empty case has to be used to prevent them from falling into the default case and have WAN address = eth0 address + 1 set to them. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for Netgear R6260 and R6850Christoph Krapp2019-08-312-1/+7
| | | | | | | | | | | As Netgear uses the same image for R6260, R6350 & R6850 we can merge device tree files and generate separate images for each device. Signed-off-by: Christoph Krapp <achterin@googlemail.com> [add missing WiFi compatible string, fix network configuration] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: fix network setup for various NETGEAR boardsDavid Bauer2019-08-311-11/+6
| | | | | | | | | | | | | | | | There are currently the following issues present for the Netgear R6220, R6350 and WNDR3700 v5: - LAN and WAN MAC-addresses are inverted - WAN MAC-address is off. It are +2 compared to the LAN MAC-address (R6350 only) - Switchport order is inverted in LuCi This commit fixes both these issues by assigning correct MAC-addresses to LAN and WAN interfaces and defining the switchports with the correct labels. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: use phy trigger for various Netgear boardsDavid Bauer2019-08-311-1/+0
| | | | | | | | | This commit switches the default trigger for the WiFi LED from a netdev trigger on "wlan0" to a wireless-phy based trigger. THis allows the LED to work, even when the wireless interface is not named "wlan0" without modifiying the LED settings. Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: add support for ADSLR G7Zhenjian Zhang2019-08-241-0/+1
| | | | | | | | | | | | | | | | | | | SoC: MT7621AT RAM: 256MB Flash: 16M SPI Ethernet: 5x GE ports WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: 1.Modify the file to linux.bin 2.Set up FTP service 3.Computer settings fixed IP: 192.168.179.50 255.255.255.0 4.Turn on the power and press and hold the reset button until the indicator light is on for about 5 seconds. Signed-off-by: Zhenjian Zhang <itdesk.zhang@gmail.com> [fix mac location] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix switch ports settingsChen Minqiang2019-08-171-3/+6
| | | | | | | | This change the switch settings for: HC5661: 4 lan ports + 1 wan port Y1S: 2 lan ports(G port) + 2 lan ports(E port) + 1 wan port Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ramips: hc5xxx: use switch trigger for ledsChen Minqiang2019-08-171-3/+7
| | | | | | | | | | netdev on eth0.2 can't show link status of wan port because eth0 is connected to builtin switch and is always link up. Use swconfig trigger instead. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> [redo commit message] Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for ipTIME A604MSungbo Eo2019-08-171-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | ipTIME A604M is a 2.4/5GHz band AC1200 router, based on MediaTek MT7628AN. Specifications: - SoC: MT7628AN - RAM: DDR2 64MB - Flash: SPI NOR 8MB - WiFi: - 2.4GHz: SoC internal - 5GHz: MT7612EN - Ethernet: 5x 10/100Mbps - Switch: SoC internal - UART: - J1: 3.3V, TX, RX, GND (3.3V is the square pad) / 57600 8N1 Installation via web interface: 1. Flash **initramfs** image through the stock web interface. 2. Boot into OpenWrt and perform sysupgrade with sysupgrade image. Revert to stock firmware: 1. Perform sysupgrade with stock image. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-141-21/+21
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* Revert faulty tree pushFelix Fietkau2019-08-121-5/+0
| | | | | | | | | | | | Revert "mac80211: add new minstrel_ht patches to improve probing on mt76x2" (9861050b85e5381c93d73ffdbc24c130400e0fb8) Revert "kernel: use bulk free in kfree_skb_list to improve performance" (98b654de2e7502507b31f0fb82befbb48f9c8542) Revert "ramips: add preliminary support for WIO ONE" (085141dc5ba5e763e1bf4c1a2fd6957160810ccc) Revert "ramips: add preliminary support for SGE AP-MTKH7-0006 developer board" (b1db6d0539511f60bf65fbde28b16afa31180e34) Revert "build: use config.site generated by autoconf-lean, drop hardcoded sitefiles" (363ce4329d4f6c00b4a7cb83dd1821fafc0d40ad) Revert "toolchain: add autoconf-lean" (fdb30eed03ae56cd87078b64d9b2fac00799e783) Revert "build: allow overriding the filename on the remote server when downloading" (6fa0e07758524eddf20c9b66dfcb55c490e1961e) Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add preliminary support for WIO ONEFelix Fietkau2019-08-121-0/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: add preliminary support for SGE AP-MTKH7-0006 developer boardFelix Fietkau2019-08-121-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips: fix lan and wan mac addresses for Cudy WR1000Davide Fioravanti2019-08-111-0/+1
| | | | | | | Lan and Wan addresses are swapped compared to the original firmware. This patch fixes this problem Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ramips: add support for HiWiFi HC5761ADENG Qingfang2019-08-082-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | HiWiFi HC5761A is an "MT7628AN variant" of HC5761 Specifications: - MediaTek MT7628AN 580MHz - 128 MB DDR2 RAM - 16 MB SPI Flash - 2.4G MT7628AN 802.11bgn 2T2R 300Mbps - 5G MT7610EN 802.11ac 433Mbps - 3x 10/100 Mbps Ethernet Flash instruction: 1. Get SSH access to the router 2. SSH to router with `ssh -p 1022 root@192.168.199.1`, The SSH password is the same as the webconfig one 3. Upload OpenWrt sysupgrade firmware into the router's `/tmp` folder with SCP 4. Run `mtd write /tmp/<filename> firmware` 5. reboot Known bug: - SD slot does not work (See PR 1500) Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: improve support for HiWiFi HC5661A and HC5861BDENG Qingfang2019-08-081-7/+6
| | | | | | | | | | | | | HC5661A: - Fix pinctrl - Fix image size (15808k) - Use switch trigger for WAN LED Both: - Use tpt LED trigger for wireless - Explicitly disable USB nodes Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn>
* ramips: add support for Fon FON2601NOGUCHI Hiroshi2019-07-261-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | FON2601 is a wireless router. Specification: - SoC: Mediatek MT7620A (580MHz) - RAM: 128 MiB - ROM: 16 MiB SPI Flash - Wireless: for 11b/g/n (upto 300 Mbps): MT7620A built-in WMAC for 11a/n/ac (upto 867 Mbps): MT7662E - Ethernet LAN: 1 port, upto 100 Mbps - Ethernet WAN: 1 port, upto 1000 Mbps - USB: 1 port (USB 2.0 host) - LEDs: 4 (all can be controlled by SoC's GPIO) - buttons: 1 (Displayed as "WPS" on enclosure) - serial port: 57600n8 pins: Vcc(3.3V), Rx, Tx, GND (left to right, viewed from outside of board) Installation (only available via UART): 1. download sysupgrade binary image by wget command 2. write sysupgrade binary image to Flash command is: mtd write sysupgrade.bin firmware 3. reboot Important Notice: Only one button is displayed as "WPS" on enclosure. However, it is configured as "reset" (factory resetting feature). Signed-off-by: NOGUCHI Hiroshi <drvlabo@gmail.com> [removed unrelated openwrt-keyring revert, missing -Wall for uimage_padhdr] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ramips: drop an empty case in 02_networkChuanhong Guo2019-07-251-4/+0
| | | | | | | There's an empty case in 02_network introduced by last commit. Drop it. Fixes: ee650ba46c ("ramips: remove needless setting of lan_mac to eth0 in 02_network") Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: remove needless setting of lan_mac to eth0 in 02_networkAdrian Schmutzler2019-07-251-10/+4
| | | | | | | | | | | This removes superfluous lines like lan_mac=$(cat /sys/class/net/eth0/address) Since lan_mac only sets the MAC address for eth0.1, these lines can be safely removed as the address will be inherited from eth0 anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consistently use lower-case factory partition labelAdrian Schmutzler2019-07-251-7/+5
| | | | | | | | The vast majority of devices labels "factory" partition with lower case. Convert the small fraction with capital letter to that and merge another case in 02_network. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: consolidate MAC address cases in 02_networkAdrian Schmutzler2019-07-251-32/+15
| | | | | | | | This just merges some duplicate definitions and consolidates lines. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Chuanhong Guo <gch981213@gmail.com> [merge duplicated cases for phicomm k2p]
* ramips: fix mac addresses used by Phicomm K2PChuanhong Guo2019-07-251-0/+4
| | | | | | | | | | | Like most mt7621 boards, Phicomm K2P stores LAN/WAN mac addresses at 0xe000/0xe006 of factory partition. Phicomm uses lan_mac-1 as wan_mac, while our default case in 02_network uses lan_mac+1. Add a special case reading lan/wan mac address for Phicomm K2P. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: add support for TP-Link RE650 v1Georgi Vlaev2019-07-172-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | TP-Link RE650 v1 is a dual-band AC2600 range extender, based on MediaTek MT7621A and MT7615E. According to the wikidevi entry for RE650 this device is identical with TP-Link RE500 as hardware. This patch supports only RE650. Hardware specification: - SoC 880 MHz - MediaTek MT7621AT - 128 MB of DDR3 RAM - 16 MB - Winbond 25Q128FVSG - 4T4R 2.4 GHz - MediaTek MT7615E - 4T4R 5 GHz - MediaTek MT7615E - 1x 1 Gbps Ethernet - MT7621AT integrated - 7x LEDs (Power, 2G, 5G, WPS(x2), Lan(x2)) - 4x buttons (Reset, Power, WPS, LED) - UART header (J1) - 2:GND, 3:RX, 4:TX Serial console @ 57600,8n1 Flash instructions: Upload openwrt-ramips-mt7621-tplink_re650-v1-squashfs-factory.bin from the RE650 web interface. TFTP recovery to stock firmware: Unfortunately, I can't find an easy way to recover the RE without opening the device and using modified binaries. The TFTP upload will only work if selected from u-boot, which means you have to open the device and attach to the serial console. The TFTP update procedure does *not* accept the published vendor firmware binaries. However, it allows to flash kernel + rootfs binaries, and this works if you have a backup of the original contents of the flash. It's probably possible to create special image out of the vendor binaries and use that as recovery image. Signed-off-by: Georgi Vlaev <georgi.vlaev@gmail.com> [re-added variables for kernel header] Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: Remove left-over mistyped device string from 02_networkAdrian Schmutzler2019-07-161-1/+0
| | | | | | | | | | | In 2011 (!), network setup for nexaira,bc2 was moved to network defaults script with a typo so it became b2c: 295e04084c ("ramips: setup bc2 mac addresses from the generic network script") This patch just removes the useless entry without replacement, since it seems to have worked for 8 years anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for ASUS RT-AC57UDavid Bauer2019-07-111-4/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: MediaTek MT7621AT RAM: 128M (Winbond W631GG6KB-15) FLASH: 16MB (Spansion S25FL128SA) WiFi: MediaTek MT7603EN bgn 2SS WiFi: MediaTek MT7612EN nac 2SS BTN: Reset - WPS LED: - Power - LAN {1-4} - WAN - WiFi 2.4 GHz - WiFi 5 GHz - USB UART: UART is present next to the Power LED. TX - RX - GND - 3V3 / 57600-8N1 3V3 is the nearest one to the Power LED. Installation ------------ Via TFTP: 1. Set your computers IP-Address to 192.168.1.75. 2. Power up the Router with the Reset button pressed. 3. Release the Reset button after 5 seconds. 4. Upload OpenWRT sysupgrade image via TFTP: > tftp -4 -v -m binary 192.168.1.1 -c put <IMAGE> Via SSH: Note: User/password for SSH is identical with the one used in the Web-interface. 1. Complete the initial setup wizard. 2. Activate SSH under "Administration" -> "System". 3. Transfer the OpenWrt sysupgrade image via scp: > scp owrt.bin admin@192.168.1.1:/tmp 4. Connect via SSH to the router. > ssh admin@192.168.1.1 5. Write the OpenWrt image to flash. > mtd-write -i /tmp/owrt.bin -d linux 6. Reboot the router > reboot Signed-off-by: David Bauer <mail@david-bauer.net>
* ramips: mt7621: merge two variants of MQmaker WiTi togetherChuanhong Guo2019-07-111-2/+1
| | | | | | | Since we can auto-detect memory now, we don't need 2 dts for two memory variants. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: Reapply sorting to board.d filesAdrian Schmutzler2019-07-102-516/+516
| | | | | | | | This patch is cosmetical: It only applies sorting based on device names, whereas renames already took place in earlier patches. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt305x: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-102-129/+129
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/rt288x,rt3883: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-102-30/+30
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt76x8: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-102-32/+32
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7621: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-103-43/+43
| | | | Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips/mt7620: Synchronize Makefiles with DTS compatibleAdrian Schmutzler2019-07-102-119/+121
| | | | | | | | | | | | | | | This will "rename" devices in Makefiles to the pattern used in DTS compatible. This will systematize naming of devices enormously. As device names are used to for default SUPPORTED_DEVICES entries, we need to adjust the source for /tmp/sysinfo/board_name, too. So remove relevant entries from base-files/lib/ramips.sh and use device compatible for that. Despite that, base-files are updated, too. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: Improve compatible for TP-Link Archer devicesAdrian Schmutzler2019-07-102-10/+10
| | | | | | | | Include "Archer" in compatible as it is part of the device name. Update Makefile device names where necessary to match compatible. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ramips: add support for TP-Link TL-WR841n v14Alexander Müller2019-07-022-0/+5
| | | | | | | | | | | | | | | | | | | | | | TP-Link TL-WR841n v14 is a router based on MediaTek MT7628N. - MediaTek MT7628NN - 32 MB of RAM - 4 MB of FLASH - 2T2R 2.4 GHz - 5x 10/100 Mbps Ethernet Installation: - copy the 'openwrt-ramips-mt76x8-tl-wr841n-v14-squashfs-tftp-recovery.bin' file to your tftp server root and rename it to 'tp_recovery.bin'. - configure your PC running the TFTP server with the static IP address 192.168.0.66/24 - push the reset button and plug in the power connector. Wait until the orange led starts blinking (~6sec) Signed-off-by: Alexander Müller <donothingloop@gmail.com> Signed-off-by: Alexander Couzens <lynxis@fe80.eu> [small modifications gpio-hog]
* ramips/leds: use devicetree alias led_wlanAlexander Couzens2019-07-021-0/+4
| | | | | | | | | | | | | | | | | | | | | | Similiar to the lantiq target use a dts alias to define the wlan led instead of static mapping in /etc/board.d/01_leds. Reduce code duplication. A device tree must define the alias "led-wlan" similiar to "led-boot". / { aliases { led-wlan = &led_wlan; }; [..] led_wlan: wlan { label = "tl-wr841n-v14:green:wlan"; gpios = <&gpio1 9 GPIO_ACTIVE_LOW>; }; }; Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ramips: add support for TOTOLINK A7000RChuanhong Guo2019-06-261-0/+1
| | | | | | | | | | | | | | | Specifications: - SoC: MT7621AT - RAM: 128MB - Flash: 16M SPI NOR - Ethernet: 5x GE ports - WiFi: 2.4G: MT7615N 5G: MT7615N Flash instruction: Upload generated sysupgrade firmware through factory web interface. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-29 10:29:18 +0000