aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ramips/base-files/etc/board.d/01_leds
Commit message (Collapse)AuthorAgeFilesLines
* ramips: fix lenovo newifi-y1 switch and LED configChuanhong Guo2018-01-091-2/+1
| | | | | | | | | | | | | | There are 3 ethernet ports on Y1. LAN1 on port1, LAN2 on port0 and WAN on port4. Use a standalone switch configuration to match this and use the switch trigger so that LAN LED could indicate the connetction status for both lan ports correctly. This patch also drop the internet led configuration, because there is a WAN led for port4 and eth0.2 isn't always used as WAN. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* ramips: fix Youku-YK1 supportEdmunt Pienkowsky2017-10-271-1/+1
| | | | | | | | | | | | | | | | | | | | | | Remove the ephy-pins from the ethernet device tree node. The ephy-pins are useed to controll the ePHY LEDs and this board doesn't have these. Instead one of the ePHY pins is used in GPIO mode to control the WAN LED. Use the switch LED trigger to control the WAN LED. Move the power LED handling to diag.sh to show the boot status via this LED. Add the missing kernel packages for USB and microSD card reader to the default package selection. Fix the maximum image size value. The board has a 32MByte flash chip. Fixes: FS#1055 Signed-off-by: Edmunt Pienkowsky <roed@onet.eu> [make the commit message more verbose, remove GPIO pinmux for pins not used as GPIOs] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Archer C50v1: fix power ledThibaut VARENE2017-07-291-1/+0
| | | | | | | | | | 01_leds had a workaround for the power led to compensate for the inverted GPIO state. This patch was missing from my previous commit. Signed-off-by: Thibaut VARENE <hacks@slashdirt.org> [add the power led default-state which was omitted in the last commit by me] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Sanlinking D240Kristian Evensen2017-04-281-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Sanlinking Technologies D240 (http://www.sanlinking.com/en/29-dual-4g-wifi-router.html) is basically the same device as the ZBT WE826, so adding support for it in LEDE is straight forward. The differences is that the D240 has two mini-PCIe slots (instead of one), blue LEDs and supports PoE. Specification: * CPU: MT7620A * 1x 10/100Mbps POE (802.3af/802.3at) Ethernet, 4x 10/100Mbps. * 16 MB Flash. * 128 MB RAM. * 1x USB 2.0 port. * 2x mini-PCIe slots. * 2x SIM slots. * 1x 2.4Ghz WIFI. * 1x button. Wifi, USB, switch and both mini-PCIe slots are working. I have not been able to test the SD card reader. The device comes pre-installed with an older version of OpenWRT, including Luci. In order to install LEDE, you need to follow the existing procedure for updating OpenWRT/LEDE using Luci. I.e., you need to access the UI and update the firmware using the sysupgrade-image. Remember to select that you do not want to keep existing settings. The default router address is 192.168.10.1 and username/password admin/root (at least on my devices). If you brick the device, the procedure for recovery is the same as for the WE826. Please see the wiki page for that device for instructions. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com>
* ramips: add support for Netgear WN3000RPv3Thibaut VARENE2017-04-281-1/+2
| | | | | | | | | | | | | | | | | | | | This patch adds support for the Netgear WN3000RPv3 http://www.netgear.com/support/product/wn3000rpv3.aspx Specifications: - SoC: MediaTek MT7620A (580MHz, ramips) - RAM: 32MB DDR - Storage: 8MB NOR SPI flash - Wireless: builtin MT7620A, 2x2:2 with u.FL connectors - Ethernet: 1x100M - Serial: JP1 header, 57600-8N1 - Stock firmware based on OpenWRT Kamikaze Like the EX2700, the bootloader expects a secondary image signature, see https://forum.openwrt.org/viewtopic.php?pid=312577#p312577 This is why the same fakeroot image is used for the WN3000 Signed-off-by: Thibaut VARENE <hacks@slashdirt.org>
* ramips: add support for VoCore2Andrew Yong2017-01-131-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the VoCore VoCore2 and its complementary "ultimate" dock. Specifications: - SoC: MediaTek MT7628AN (580MHz, ramips) - RAM: 128MB DDR2 166MHz - Storage: 16MB NOR SPI flash onboard + microSD slot on dock - Wireless: Built into MT7628AN (mt76) with 1T1R firmware on VoCore2 boards with onboard 1x chip antenna - Ethernet: 1x100M (port0) on dock, 1x100M (port2) on PCB header - Dock hardware: - USB 2.0 socket - MicroSD socket - 100Mbps Ethernet x1 - 3.5mm headphone jack (TRRS) connected to Everest Semi ES8388 I2S DAC/ADC (support WIP) - Micro USB for power and console (UART2) Initial installation: - VoCore2 comes preinstalled with a fork of OpenWrt CC and AP on SSID "VoCore2" - Connect to VoCore2 by Ethernet or Wi-Fi - `ssh root@192.168.1.1` (password is "vocore") - scp/wget/etc. LEDE sysupgrade.bin to VoCore2 - `sysupgrade -n <your image>.bin` (don't keep old config, as the original firmware uses Ralink SDK Wi-Fi drivers and not mt76+mac80211) - after sysupgrade completes, Wi-Fi will be disabled by default so use Ethernet or the micro USB console to configure Wi-Fi again Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: MiWiFi Nano fixesL. D. Pinney2017-01-021-5/+0
| | | | | | | | | | | | | | | | Use the the dt-bindings macros and add the reset button. Set the correct polarity for the LEDs and drop the default state. Remove all trigger for the LEDs. According to the manual the LEDs are only used to show the operation state, where blue means normal operation. Use the MAC-Addresses stored in EEPROM for the ethernet and the wireless interface. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> [use leds only for boot status indication, add proper commit message] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use D-Link DIR-600 B1 image for B2 versionMathias Kresin2016-12-241-1/+0
| | | | | | | Everything set for the B1 is identical to the values uses for the B2 version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: use destinct 11AC NAS board nameMathias Kresin2016-12-241-11/+10
| | | | | | | | | | Use a distinct board name even if the board is near to identical to the WeVO W2914NS v2. To make sure that a 11AC NAS image can not be installed on a WeVO W2914NS v2, both board need to use different names. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: Add support to TP-Link Archer MR200Henryk Heisig2016-12-221-0/+6
| | | | | | | | | | CPU: MT7620N 580MHz Flash: 8MB RAM: 64MB build-in modem 3G/4G four ethernet port 10/100Mbps Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: add support for ZyXEL Keenetic Omni / Omni IIVitaly Chekryzhev2016-12-221-0/+2
| | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com>
* ramips: Fix led init script for Lenovo Y1/Y1sBangLang Huang2016-12-041-3/+10
| | | | | | | This commit fix the led init script for Lenovo Y1 and Y1S due to the manual and dts file. Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: improve F5D8235 V1 supportTobias Wolf2016-12-041-1/+5
| | | | | | | | | | | | | | | | | | | This fixes the partition name for the firmware splitter, the cfi address and adds the mtd-eeprom address for wmac. It adds additional LEDs and make use of them in diag.sh and 01_leds. Please note that the ":blue:wired" LED is used because the ":blue:router" behaviour is unpredictable for failsafe indication. The issue with the router LED is that you have two states only. "off" is steady on and "on" blinks. Therefore the wired LED is more suitable. Furthermore it reuses the correct switch configuration definition to reflect the device ports and numbering. Additionally fixes the issue that the default configuration is not applied as no port 6 exists on this device. Signed-off-by: Tobias Wolf <github-NTEO@vplace.de>
* ramips: add support for WeVO W2914NS v2perillamint2016-11-211-0/+3
| | | | Signed-off-by: Yong-hyu Ban <perillamint@gentoo.moe>
* ramips: add support for ZyXEL Keenetic VivaVitaly Chekryzhev2016-11-181-0/+4
| | | | | | | | | Factory image can be installed via Zyxel WebUI. Signed-off-by: Vitaly Chekryzhev <13hakta@gmail.com> [removed linux,modalias parameter from flash node in dts] [removed sdhci node from dts; no sd card slot here] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ar71xx, ramips: reduce CPU load and flickering on devices using rssliedsMartin Weinelt2016-11-161-2/+2
| | | | | | | | | Polling every 40ms causes more than 10% CPU load on weak devices. An interval of 200ms is much more reasonable. Signed-off-by: Martin Weinelt <martin@darmstadt.freifunk.net> [Matthias Schiffer: adapt OpenWrt patch; add ramips; extend commit message] Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ramips: Add support for Wavlink WL-WN575A3Roger Pueyo Centelles2016-11-081-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the Wavlink WL-WN575A3, a dual-band wall-plug wireless router with the following specifications: - CPU: MediaTek MT7628AN 580MHz - Flash: 8MB - RAM: 64MB - Ethernet: 2x 10/100 Mbps (switched) - 2.4 GHz: 802.11b/g/n SoC, MIMO 2x2, 20 dBm - 5 GHz: 802.11a/n/ac MT7612E, MIMO 2x2, 20 dBm - Antennas: 4x external (2 per radio), non-detachable - LEDs: 4 programmable + LAN, WAN, POWER - Buttons: reset, WPS Flashing instructions: Factory U-boot launches a TFTP client if WPS button is pressed during power-on. Rename the sysupgrade file and configure a TFTP as follows: - Client (WL-WN575A3) IP: 192.168.10.101 - Server IP: 192.168.10.100 - Filename: firmware.bin Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips: Archer C50 cleanupHenryk Heisig2016-10-311-5/+6
| | | | | | | | | | | - setting read-only flag to important partitions - enabling PA to improve 2.4 GHz signal strength - add missing leds - rename colour led - add mac adress to 5GHz wlan interface - included <dt-bindings/input/input.h> and <dt-bindings/gpio/gpio.h> Signed-off-by: Henryk Heisig hyniu@o2.pl
* ramips: fix PSG1218 LEDsXuefu Lin2016-10-261-1/+2
| | | | Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: add support for Planex VR500.YuheiOKAWA2016-10-151-1/+2
| | | | | | | | | | | | SOC: MT7621A RAM: 256MiB NOR: MX25L51245G Non Wireless Router. Issue: soft reboot problem. SPI Flash do not exit 4byte address mode. Signed-off-by: Yuhei Okawa <tochiro.srchack@gmail.com>
* ramips: improve edimax 6200n/nl supportMathias Kresin2016-10-151-3/+3
| | | | | | | | | | Assign the reset functionality to the wps/reset buttons. Use the wlan switch of the 6200n to enable/disable wlan. Add the internet led of the 6200nl and use the led for boot status indication Signed-off-by: Mathias Kresin <dev@kresin.me>
* ramips: add support for Zyxel NBG-419N2 (WAP3205v2)Klaus2016-10-041-0/+4
| | | | | | | | | | | applied bb-final-ramips-add-zyxel-nbg-419n2.patch from 123serge123, found at https://yadi.sk/d/1ZV0lKJwbTE65; see https://forum.openwrt.org/viewtopic.php?pid=246905#p246905, modified slightly to fit to CC release and to new lede build system: image/rt305x.mk include file is used now changed NBG-419N2.dts format to fit style of other dts files Signed-off-by: Klaus <k-laus@quantentunnel.de>
* ramips: Add support for Phicomm K2 PSG1218Xuefu Lin2016-10-041-0/+3
| | | | | | | | | - CPU: MT7620A 580MHz - Flash: 8MB - RAM: 64MB - External PA+LNA on both WLAN2.4 and WLAN5 - 4x LAN ethernet and 1x WAN ethernet Signed-off-by: Xuefu Lin <xuefulin@gmail.com>
* ramips: Xiaomi MiWiFi Nano: fix status ledCezary Jackiewicz2016-09-291-2/+1
| | | | | | | - add status led for Xiaomi MiWiFi Nano - revert https://github.com/lede-project/source/commit/af1e70b4a730e91ce1668d506ebc5c1c8cf5abf5 , this should not be added. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips : add support for Newifi D1BangLang Huang2016-09-271-0/+3
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips : add support for PandoraBox D1BangLang Huang2016-09-271-0/+3
| | | | Signed-off-by: BangLang Huang <banglang.huang@foxmail.com>
* ramips: Add support for ZBT-CPE102Cezary Jackiewicz2016-09-271-0/+3
| | | | | | | | | | - CPU: MT7620N 580MHz - Flash: 8MB - RAM: 64MB - build-in minipcie slot for modem 3G/4G - one ethernet port 10/100Mbps Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: Add support for TEW-714TRUJimmy Zhong2016-08-101-0/+4
| | | | Signed-off-by: Jimmy Zhong <mb300sd@mb300sd.net>
* ramips: Rename TP-Link Archer C50 LEDsP.Wassi2016-07-261-5/+5
| | | | | | | Rename LEDs in TP-Link Archer C50 from [manufacturer name] to [board name] ("tp-link" -> "c50") Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: Improve TP-Link Archer C20i supportP.Wassi2016-07-261-0/+6
| | | | | | Improve / finalise TP-Link Archer C20i support. Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: unify etc/board.d/01_leds configurationP.Wassi2016-07-241-2/+2
| | | | | | | Introduce an optional parameter at the local set_usb_led and set_wifi_led function such that they can take a triggering device. If no parameter is passed, behaviour is unchanged. Signed-off-by: P.Wassi <p.wassi@gmx.at>
* ramips: remove indentation in etc/board.d/01_ledsPaul Wassi2016-07-241-1/+1
| | | | | Remove indentation at end of line in base-files/etc/board.d/01_leds Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* ramips: Add support for D-Link DCH-M225Michael Lee2016-07-111-0/+4
| | | | | | | | D-Link DCH-M225 is based on Mediatek MT7620 with 64MB ram, 8MB flash, 3.5mm audio out support. but no ethernet and usb ports. so you must default enable wifi. Signed-off-by: Michael Lee <igvtee@gmail.com>
* ramips: add button support and make LEDs known to userspace for DIR-860L B1Matthias Schiffer2016-06-301-0/+3
| | | | | Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Reviewed-by: Jo-Philipp Wich <jo@mein.io>
* ramips: add suport for ZBT APE522IIRoger Pueyo Centelles2016-06-221-0/+5
| | | | | | | | | The ZBT APE522II is a dual-radio outdoor CPE based on the MT7620a SoC. It has 64 MB RAM, 8 MB flash, 2 Fast Ethernet ports via internal switch (one with 802.3af 48V PoE support), a 802.11b/g/n SoC 2.4 GHz radio and an 802.11a/n/ac MT7612E-based 5 GHz radio. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* ramips/base-files: Add support for Archer C50Henryk Heisig2016-06-131-0/+7
| | | | Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* ramips: Add status led for Xiaomi MiWiFi NanoCezary Jackiewicz2016-05-231-1/+2
| | | | Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* ramips: add initial support for SamKnows SK-WB8Andrew Yong2016-05-121-0/+1
| | | | Signed-off-by: Andrew Yong <me@ndoo.sg>
* ramips: add support for Planex MZK-EX750NP.blogic2016-05-101-0/+4
| | | | | | | | | | | add support for Planex MZK-EX750NP. MZK-EX750NP is MT7620A and MT7610E based 11ac wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49268
* ramips: Add support for the Netgear WNDR3700v5John Crispin2016-04-261-0/+3
| | | | | | | | | | https://wiki.openwrt.org/toh/netgear/wndr3700 wndr3700v5 uses the single-core dual thread MediaTek MT7621S SoC. Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 49247
* ramips: add support for Planex MZK-EX300NPJohn Crispin2016-04-261-1/+2
| | | | | | | | | | MZK-EX300NP is MT7620A based wifi repeater. Built-in power supply. 64MiB RAM, 8MiB SPI Flash, non Wired Ethernet. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49235
* ramips: add support for Planex CS-QR10John Crispin2016-04-261-1/+2
| | | | | | | | | | | | CS-QR10 is MT7620A based IP Camera. the camera and sound does not work with kernel 4.4. - camera chip is sn9c291. - sound chip is wm8960. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49234
* ramips: add support for ELECOM WRH-300CRJohn Crispin2016-04-211-0/+4
| | | | | | | | | | | | | | ELECOM WRH-300CR is MT7620N based very small Wi-Fi router with 64MiB DDR2 SDRAM, 16MiB SPI Flash, one fast ethernet port, and (internal but easy-to-access) UART. it also has internal USB hub and USB card reader which provide one USB port, one SD card slot, and one microSD card slot. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> Signed-off-by: FUKAUMI Naoki <naobsd@gmail.com> SVN-Revision: 49211
* ramips: fix support Planex MZK-750DHP.John Crispin2016-04-201-0/+1
| | | | | | | | | | fix script for Planex MZK-750DHP. modification of the GPIO definition. add Profile. Signed-off-by: YuheiOKAWA <tochiro.srchack@gmail.com> SVN-Revision: 49205
* ramips: MiWifi-Nano - change gpios to leds, add to default build groupJohn Crispin2016-03-201-0/+5
| | | | | | | | | | | | 1) Use leds to indicate: Red - Power Amber - Radio On Blue - Wifi associated 2) Add profile to default build group for MT7628 subtarget Signed-off-by: Noble Pepper <openwrtmail@noblepepper.com> SVN-Revision: 49045
* ramips: Add support for GL-MT750John Crispin2016-03-101-1/+2
| | | | | | | | This patch adds support for GL-MT750. GL-MT750 is powered by MT7620A and MT7610e, dual band 802.11ac, 2.4G 300Mbps and 5G 450Mbps. It has 5 LANs, MMC interface, USB, a lot of IOs and PoE support. SVN-Revision: 48994
* ramips: Add support for GL-MT300NJohn Crispin2016-03-101-1/+2
| | | | | | | | This patch adds support for GL-MT300N. GL-MT300N is powered by MT7620N with 16MB flash, 64MB RAM, 2 LANs, USB, UART, GPIO and PoE support. SVN-Revision: 48993
* ramips: Add support for GL-MT300AJohn Crispin2016-03-101-0/+3
| | | | | | | | This patches adds support for GL-MT300A. GL-MT300A is powered by MT7620A. It has 16MB flash, 128MB RAM, Two LANs, USB, UART and MMC daughter board. SVN-Revision: 48992
* ramips: Incorrect file mode changeJohn Crispin2016-03-031-0/+0
| | | | | | | | | | | Commit d0f5ab6d95a1 ("ramips: Added support for ZBT-826 / ZBT-1026") incorrectly changed the mode of the ramips shell scripts from 755 to 644. I.e., they are not excutable any more and for example devices will be left with broken configs. Signed-off-by: Kristian Evensen <kristian.evensen@gmail.com> SVN-Revision: 48893
* ramips: Added support for ZBT-826 / ZBT-1026John Crispin2016-03-011-0/+5
| | | | | | | | | Support for these MT7620-based routers: https://wiki.openwrt.org/toh/zbt/we-826 Based on Oskari’s patches found here: https://dev.openwrt.org/ticket/19996 Signed-off-by: Jamie Stuart <jamie@onebillion.org> SVN-Revision: 48865
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-15 08:38:42 +0000