| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch
target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch
target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch
target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch
target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch
The following patch does not apply to upstream any more and needs some
more work to make it work fully again. I am not sure if we are still
able to set the UART to a none standard baud rate.
target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch
These patches needed manually changes:
target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch
target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch
target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch
target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch
target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch
All others updated automatically.
Compile-tested on: malta/le, armvirt/64, lantiq/xrx200
Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed:
generic/backport-5.4/790-v5.7-net-switchdev-do-not-propagate-bridge-updates-across.patch
All others updated automatically.
Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Hardware specification
----------------------
* CN9130 SoC, Quad-core ARMv8 Cortex-72 @ 2200 MHz
* 4 GB DDR
* 4 GB eMMC
* mmcblk0
- mmcblk0p1 64M kernel_1
- mmcblk0p2 64M kernel_2
- mmcblk0p3 512M rootfs_1
- mmcblk0p4 512M rootfs_2
- mmcblk0p5 512M Reserved
- mmcblk0p6 64M Reserved
- mmcblk0p7 1.8G rootfs_data
* 4 MB (SPI Flash)
* 6 x 2.5 Gigabit ports (Puzzle-M901)
- External PHY with 6 ports (AQR112R)
* 6 x 2.5 Gigabit ports (Puzzle-M902)
- External PHY with 6 ports (AQR112R)
3 x 10 Gigabit ports (Puzzle-M902)
- External PHY with 3 ports (AQR113R)
* 4 x Front panel LED
* 1 x USB 3.0
* Reset button on Rear panel
* UART (115200 8N1,header on PCB)
Flash instructions:
The original firmware is based on OpenWrt.
Flash firmware using LuCI and CLI
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
(cherry picked from commit 70c75965a97799b44871249c205bad48fea9a4ae)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
| |
1. Add support for Marvell CN9130 SoC
2. Add support for CP115,and create an armada-cp11x.dtsi file which will be used to instantiate both CP110 and CP115
3. Add support for AP807/AP807-quad,AP807 is a major component of CN9130 SoC series
4. Drop PCIe I/O ranges from CP11x file and externalize PCIe macros from CP11x file
Signed-off-by: Ian Chang <ianchang@ieiworld.com>
(cherry picked from commit c98ddf0f019986bbb4c868bfcaf97e0d1f4ee2dc)
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
generic/backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch
generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch
mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch
Removed upstreamed:
generic/backport-5.4/040-ARM-8918-2-only-build-return_address-if-needed.patch
layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch
All others updated automatically.
Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This patch has been carried since introduction throughout every kernel
major bump and no one has tested if the later kernels improved the
situation. The Armada 3720 SoC can only process GbE interrupts on Core 0
and this is already limited in all stable kernels, so ditch this
workaround for 64 bit SoCs.
Ref: https://git.kernel.org/torvalds/c/cf9bf871280d
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
(cherry picked from commit cbdd2b62e4d5e0572204c37d874d32dc8610840e)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased:
bcm27xx/patches-5.4/950-1031-net-lan78xx-Ack-pending-PHY-ints-when-resetting.patch
Removed upstreamed:
mvebu/patches-5.4/100-cpufreq-armada-37xx-forbid-cpufreq-for-1.2-GHz-variant.patch
All others updated automatically.
Compile-tested on: lantiq/xrx200, armvirt/64
Runtime-tested on: lantiq/xrx200, armvirt/64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
| |
Compile-tested: ath79-generic ipq40xx-generic
Run-tested: ipq40xx-generic
Signed-off-by: David Bauer <mail@david-bauer.net>
|
|
|
|
|
|
|
|
|
|
|
| |
This patch is backported from linux-arm-kernel [1] to improve situation, when
it was reported that 1.2 GHz variant is unstable with DFS.
It waits to be accepted upstream, however, it waits for Marvell people to respond.
[1] https://patchwork.kernel.org/project/linux-arm-kernel/patch/20210630225601.6372-1-kabel@kernel.org/
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit d3794768177293f584cc74f90c921276793da1e7)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Based on the discussion on the mailing list [1], the patch which was
reverted, it reverts only one patch without the subsequent ones.
This leads to the SoC scaling issue not using a CPU parent clock, but
it uses DDR clock. This is done for all variants, and it's wrong because
commits (hacks) that were using the DDR clock are no longer in the mainline kernel.
If someone has stability issues on 1.2 GHz, it should not affect all
routers (1 GHz, 800 MHz) and it should be rather consulted with guys, who are trying to
improve the situation in the kernel and not making the situation worse.
There are two solutions in cases of instability:
a) disable cpufreq
b) underclock it up to 1 GHz
This reverts commit 080a0b74e39d159eecf69c468debec42f28bf4d8.
[1] https://lists.openwrt.org/pipermail/openwrt-devel/2021-June/035702.html
CC: Pali Rohár <pali@kernel.org>
Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
(cherry picked from commit 7b868fe04a8961048feec1143e72fe47bde52a12)
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased
generic/pending-5.4/680-NET-skip-GRO-for-foreign-MAC-addresses.patch
All others updated automatically.
Compile-tested on: ramips/mt7621, armvirt/32
Runtime-tested on: ramips/mt7621, armvirt/32
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Manually rebased
bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch
Replaced with patch from Raspberry Pi kernel 5.10 patches
mvebu/patches-5.4/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch
Applied upstream
All others updated automatically.
Compile-tested on: ath79/generic, lantiq/xrx200, brcm27xx
Runtime-tested on: ath79/generic, lantiq/xrx200
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
5.10.37 and 5.4.119 introduced a lot of DVFS changes for Armada 37xx from 5.13 kernel.
Unfortunately commit:
https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/drivers/cpufreq/armada-37xx-cpufreq.c?h=v5.10.37&id=a13b110e7c9e0dc2edcc7a19d4255fc88abd83cc
This patch actually corrects the things so that 1 or 1.2GHz models would actually get scaled to their native frequency.
However, due to a AVS setting voltages too low this will cause random crashes on 1.2GHz models.
So, until a new safe for everybody voltage is agreed on
lets revert the patch.
Fixes: 9d21ecc ("kernel: bump 5.4 to 5.4.119")
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
(cherry picked from commit 080a0b74e39d159eecf69c468debec42f28bf4d8)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed because in upstream
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
ath79/patches-5.4/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch
ramips/patches-5.4/999-fix-pci-init-mt7620.patch
Manually rebased
ath79/patches-5.4/0033-spi-ath79-drop-pdata-support.patch
All others updated automatically.
Compile-tested on: x86/64, ath79/generic
Runtime-tested on: x86/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
| |
Kernel 5.10 is not supported by OpenWrt 21.02, remove this patch.
Fixes: d530ff37bf33 ("mvebu: armada 370: dts: fix the crypto engine")
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
| |
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit ed4641e9f1ad940cb60187dea09cf17c865efcaf)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed because in upstream*
mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch
Manually rebased*
generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch
Added new backport*
generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch
All others updated automatically.
The new backport was included based on this[1] upstream commit that will be
mainlined soon. This change is needed because Eric Dumazet's check for
NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use
napi_gro_frags().
Compile-tested on: x86/64, armvirt/64, ath79/generic
Runtime-tested on: x86/64, armvirt/64, ath79/generic
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The crypto engine in Armada 370 SoCs is currently broken. It can be
checked installing the required packages for testing openssl with hw
acceleration:
opkg install openssl-util
opkg install kmod-cryptodev
opkg install libopenssl-devcrypto
After configuring /etc/ssl/openssl.cnf to let openssl use the crypto
engine for digest operations, and performing some checksums..
md5sum 10M-file.bin
openssl md5 10M-file.bin
...we can see they don't match.
There might be an alignment or size constraint issue caused by the
idle-sram area.
Use the whole crypto sram and disable the idle-sram area to fix it. Also
disable the idle support by adding the broken-idle property to prevent
accessing the disabled idle-sram.
We don't care about disabling the idle support since it is already broken
in Armada 370 causing a huge performance loss because it disables
permanently the L2 cache. This was reported in the Openwrt forum and
elsewhere by Debian users with different board models.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
(cherry picked from commit 2e1ebe96c61424d0829bb1c8b5ec44aaa8bea8af)
|
|
|
|
|
|
|
|
|
|
|
|
| |
The GL.iNet GL-MV1000 is booting from eMMC and the images for it are in
theory sysupgrade compatible. But the platform upgrade scripts were not
adjusted to select the mmcblock device as upgrade target. This resulted in
a failed sysupgrade because the mtd device (NOR flash) was instead tried to
be modified by the sysupgrade script.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 07e5e03711d55f94db738446ef9eddc8163b53a6)
|
|
|
|
|
|
|
| |
Move some disabled symbols found in armvirt target to generic.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
(cherry picked from commit 12e942b1fdda874542e0a4e6ea892969fedab975)
|
|
|
|
|
|
|
|
|
| |
1. Use upstream accepted NVMEM patches
2. Minor fix for BCM4908 partitioning
3. Support for Linksys firmware partitions on Northstar
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 3fd0a4222b6efbfbdb560c5b13e899ecda627494)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The original GL.iNet firmware has two different mac addresses in the
factory/art partition. The first one is for the WAN interface only and the
second one is for both lan0 and lan1.
But the original submission for OpenWrt didn't initialize the mac
addresses of the LAN ports for the DSA device at all. The ethernet mac
address was then used for all DSA ports.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit c20ac84803242e5a6451184009dabc36ba83b96e)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The original patch to support this device advertised support for the reset
button and the "switch" in the commit message. But neither were actually
integrated in the device tree or documented anywere.
The button itself is now used to trigger a reset (as described in the
official GL.iNet documentation). The switch itself is registered as BTN_0
like other devices from GL.iNet in ath79.
Fixes: 050c24f05c85 ("mvebu: add support for GL.iNet GL-MV1000")
Signed-off-by: Sven Eckelmann <sven@narfation.org>
(cherry picked from commit 01b911a9381426314762822f97e3a7e658295f50)
|
|
|
|
|
|
|
|
| |
Kernel size limits have been dealt with.
Effective revert of a1eb2c46 and ac9730c4.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit b4f76d9f0d61779b5e04228d1eb3f2ba412ffd26)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
venom has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
venom uboot however as set from factory will load up to 6MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0x900000, size 0x600000
6291456 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "priKernSize";
priKernSize=0x0600000
Resize the root partitions from 120MB to 117MB to let kernel expand
into it another 3MB.
And set kernel target size to 6MB.
Lastly set the kernel-size-migration compatibility version on venom to
prevent sysupgrading without first reinstalling from a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 15309f5133d55e92bec3ed91dfb3ac9d124f6a96)
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
mamba has a 3MB kernel partition as specified by the DTS.
3MB is not sufficient for building with many kernel modules or newer
kernel versions.
mamba uboot however as set from factory will load up to 4MB.
This can be observed by looking a uboot log:
NAND read: device 0 offset 0xa00000, size 0x400000
4194304 bytes read: OK
and from uboot environment variables:
$ fw_printenv | grep "pri_kern_size";
pri_kern_size=0x400000
Resize the root partitions from 37MB to 36MB to let kernel expand
into it another 1MB.
And set kernel target size to 4MB.
Lastly add a compatibility version message: kernel-size-migration.
And set it on mamba to prevent sysupgrading without first reinstalling from
a factory image.
Signed-off-by: Tad Davanzo <tad@spotco.us>
(cherry picked from commit 10415d5e7016b69dc71c5f1b03e8e17b586f8edd)
|
|
|
|
|
|
|
|
|
| |
This patch enables LED support for the GL.iNet GL-MV1000
Signed-off-by: Jeff Collins <jeffcollins9292@gmail.com>
[add SPDX identifier on new file, add aliases, minor cosmetic issues]
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
(cherry picked from commit 6e0c780eb3b4ba1e52216c1d671897749dd81829)
|
|
|
|
|
|
|
|
|
| |
It's meant to provide upstream support for mtd & NVMEM. It's required
e.g. for reading MAC address from mtd partition content. It seems to be
in a final shape so it's worth testing.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit e90e75b12c818c49704755b9e530491aee2d554c)
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds the latest version of ofpart commit. It hopefully
1. Doesn't break compilation
2. Doesn't break partitioning
(this time).
It's required to implement fixed partitioning with some quirks. It's
required by bcm53xx, bcm4908, kirkwood, lantiq and mvebu.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
(cherry picked from commit 7a7b2fd809809fbd7045bd3dad4fc896a6fef06f)
|
|
|
|
|
|
|
|
|
| |
Refreshed all patches.
Compile-tested on: ath79, lantiq, ipq40xx, x86_64
Runtime-tested on: ipq40xx, x86_64
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
Backport [1] and fix [2] hardware buffer management. Also fix the IRQ storm
caused by a misconfiguration of the PCA9538 interrupt pin [3].
[1] https://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux.git/commit/arch/arm/boot/dts/armada-385-turris-omnia.dts?id=018b88eee1a2efda26ed2f09aab33ccdc40ef18f
[2] https://lore.kernel.org/linux-arm-kernel/20210217153038.1068170-1-rsalvaterra@gmail.com/
[3] https://lore.kernel.org/linux-arm-kernel/20210220231144.32325-1-kabel@kernel.org/
Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
(cherry picked from commit 6fe6b631ef91a8a44d7324329ad6aaec6f08ada6)
|
|
|
|
|
|
|
|
|
|
| |
There are proper workarounds merged to 5.4 stable tree for ESPRESSObin
boards with older bootloader:
4e1a23779bde ("ata: ahci: mvebu: Make SATA PHY optional for Armada 3720")
40af962eb1d4 ("usb: host: xhci: mvebu: make USB 3.0 PHY optional for
Armada 3720")
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
|
|
|
|
|
| |
Use SPDX license tags to allow machines to check licenses.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
| |
Use SPDX license tags to allow machines to check licenses.
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
| |
All modification made by update_kernel.sh in a fresh clone without
existing toolchains.
Build-tested: bcm27xx/bcm2711, ipq806x/R7800,
Run-tested: ipq806x/R7800
No dmesg regressions, everything functional
Signed-off-by: John Audia <graysky@archlinux.us>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Currently it's not possible to boot the device with just initramfs image
without additional effort as the initramfs image doesn't contain device
tree. Fix it by producing FIT based image which could be booted with
following commands:
setenv bootargs earlyprintk console=ttyS0,115200
tftpboot ${kernel_addr_r} openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootm ${kernel_addr_r}
Acked-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tmn505@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The thermal zones kernel documentation is misleading, we cannot use more
than one sensor in a thermal zone node.
Furthermore the drivetemp driver for some reason it only catches one
sensor from the hard drives array (the first available).
In the Buffalo Linkstation LS421DE board there is also a sensor at the
ethernet phy chip that can also be monitored. Very useful to stop the fan
when there are no hard drives in the bays.
(It might be also possible to add the CPU sensor, but it requires kernel
patching for registering the sensor via device tree, using the function:
devm_thermal_zone_of_sensor_register)
Fix the thermal zones to use only one sensor per node and add the ethernet
phy sensor. Also adjust the hdd temperatures to be more conservative for
a mechanical hard drive.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The majority of our targets provide a default value for the variable
SUPPORTED_DEVICES, which is used in images to check against the
compatible on a running device:
SUPPORTED_DEVICES := $(subst _,$(comma),$(1))
At the moment, this is implemented in the Device/Default block of
the individual targets or even subtargets. However, since we
standardized device names and compatible in the recent past, almost
all targets are following the same scheme now:
device/image name: vendor_model
compatible: vendor,model
The equal redundant definitions are a symptom of this process.
Consequently, this patch moves the definition to image.mk making it
a global default. For the few targets not using the scheme above,
SUPPORTED_DEVICES will be defined to a different value in
Device/Default anyway, overwriting the default. In other words:
This change is supposed to be cosmetic.
This can be used as a global measure to get the current compatible
with: $(firstword $(SUPPORTED_DEVICES))
(Though this is not precisely an achievement of this commit.)
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The following four led triggers are enabled in generic config.
* kmod-ledtrig-default-on
* kmod-ledtrig-heartbeat
* kmod-ledtrig-netdev
* kmod-ledtrig-timer
Drop the packages and remove them from DEVICE_PACKAGES.
There's no other package depending on them in this repo.
Signed-off-by: Sungbo Eo <mans0n@gorani.run>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Removed upstreamed patches:
pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch
Manually merged:
pending-5.4/611-netfilter_match_bypass_default_table.patch
layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch
Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny},
ipq40xx, octeon, ramips/mt7621, realtek, x86/64
Run-tested: ipq806x/R7800, realtek
Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
Tested-by: John Audia <graysky@archlinux.us>
Tested-by: Stijn Segers <foss@volatilesystems.org>
|
|
|
|
|
|
| |
Move some disabled config options found in lantiq target to generic.
Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
|
|
|
|
|
|
|
|
|
|
|
| |
This reverts commit e401a2a42e6d7c892e1cf7d765fa5ec9b2db3fb3 as at least
two users had reported breakage on their devices.
References: https://lists.infradead.org/pipermail/openwrt-devel/2020-December/032837.html
References: https://github.com/openwrt/openwrt/commit/e401a2a42e6d7c892e1cf7d765fa5ec9b2db3fb3#commitcomment-45189788
Cc: Karel Kočí <karel.koci@nic.cz>
Reported-by: Magnus Kroken <mkroken@gmail.com>
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
|
| |
Backport the upstream kernel fix 525b0858ff to get rid of the kernel
messages:
mvebu-gpio xxxxxx.gpio: IRQ index 3 not found
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The Buffalo Linkstation LS421DE comes with a Ricoh RS5C372A real time
clock. This RTC has the INTRA pin connected to the power management
circuit, allowing to wake up the device from the power off state when an
alarm is scheduled.
Add the "wakeup-source" property in the RTC dts node to allow the use
of the alarm.
Example of use, the device is powered off and it comes to life after 5
minutes:
echo $(expr $(date '+%s') + 60 * 5) > /sys/class/rtc/rtc0/wakealarm
poweroff
This feature isn't available in the stock firmware.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
| |
The Buffalo Linkstation LS421DE isn't able to enable the Level 2 cache
(AKA Aurora cache). As of result of this, the throughput is about half of
the expected, e.g when doing network data transfers.
Fix it by adding the broken-idle property in the coherency fabric node.
Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
With board revision 1.3, SolidRun moved the power LED to the middle of
the board. In old place of power LED a GPIO controllable heartbeat LED
was added. This commit touches only Single Shot variant, because all
have revision 1.3. Some boards could be placed in an enclosure, therefore
the LED18 is enabled by default, since that'll be the only visible
indicator that the board is operating.
Ref: http://wiki.macchiatobin.net/tiki-index.php?page=Schematics#Revision1.3_Electrical_Design_Changes
Ref: http://macchiatobin.net/wp-content/uploads/2017/11/MACCHIATOBin-rev-1_3.pdf
Reported-by: Alexandra Alth <alexandra@alth.de>
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
This adds DTB to kernel and that way makes it possible to easily boot
initramfs image and also kernel.
The sequence to boot initramfs on Omnia is then just:
env set bootargs earlyprintk console=ttyS0,115200
dhcp 0x1000000 192.168.1.1:openwrt-mvebu-cortexa9-cznic_turris-omnia-initramfs-kernel.bin
bootz 0x1000000
Without this change kernel boot won't proceed and is stuck on "Starting
kernel".
Signed-off-by: Karel Kočí <karel.koci@nic.cz>
[fixed From: to match with SoB:]
Signed-off-by: Petr Štetiar <ynezz@true.cz>
|
|
|
|
|
|
|
|
| |
This will explain what is actually occuring on dd invocations.
Additionally remove comments for steps which are described by printed
statements anyway.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
|
|
|
|
|
| |
Sync with x86 target changes.
Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixup dfa357a3de "mvebu: base-files: Update Turris Omnia U-Boot
environment" which should have included this file as well.
By rebasing the initial patch this file somehow disappeared.
Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
Reviewed-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
Tested-by: W. Michael Petullo <mike@flyn.org> (Turris Omnia "2020")
Tested-by: Klaus Kudielka <klaus.kudielka@gmail.com> (Turris Omnia)
[explain fixup in commit message]
Signed-off-by: Paul Spooren <mail@aparcar.org>
|