aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mvebu
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: clearfog: assign SFP port to WAN zoneJosua Mayer2017-05-301-1/+1
| | | | | | | | | The single SFP port is meant for direct media access to WAN, such as VDSL2, GPON). While it could also be used for in-home fiber, it is much more likely that the LAN is standard ethernet, especially considering that SFP is the onmly port that can go beyond 1Gbps. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: clearfog: document interface configurationJosua Mayer2017-05-301-6/+9
| | | | | | | | | | | | | Take explicit note of what physical ports eth{0,1,2} refer to. Also repair port assignment: At some point between 4.9.20 and 4.9.29 the numbering changed. Keep previous port assignment that was: LAN = SFP+Switch WAN = standalone ethernet Also use the same assignment for Clearfog-Base to avoid confusion. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: clearfog: include DTB for all variants in imageJosua Mayer2017-05-301-3/+5
| | | | | | | Installing all armada-388-clearfog-* DTBs in the same sdcard image, it now becomes much easier to swap sdcards between different device variants. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: update boot-script to use generic variablesJosua Mayer2017-05-302-10/+44
| | | | | | | | | | | U-Boot provides standard variables for load addresses, and filesystem-agnostic load-commands. Furthermore thanks to distro-boot, the device and partition from which the system boots is known. The new boot-script makes use of all this information. Tested on the only board that uses this boot-script: Clearfog Pro Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* kernel: update kernel 4.9 to 4.9.29Koen Vandeputte2017-05-217-15/+15
| | | | | | | | | | | | | - Refresh all patches - Removed upstreamed - Adapted 1 Compile tested on: bcm53xx, cns3xxx, imx6, lantiq Run tested on: cns3xxx & imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [update from 4.9.28 to 4.9.29] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: ClearFog Base fix phy initMarko Ratkaj2017-05-141-0/+61
| | | | | | | Fix Marvell PHYs initialization issues and optimize logic for page changing during init Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: add ClearFog Base supportMarko Ratkaj2017-05-145-0/+36
| | | | | | | | | | Add support for SolidRun ClearFog Base board. The base model is a smaller version of ClearFog Pro without the DSA switch, replacing it with a second copper gigabit port, and only one PCIe socket. Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: add ClearFog Base device tree filesMarko Ratkaj2017-05-142-0/+725
| | | | | | | | | | | | Add device tree files for Solidrun ClearFog Base board. We also need to backport some improvements for Armada 388 MicroSoM. The base model is a smaller version of ClearFog Pro without the DSA switch, replacing it with a second copper gigabit port, and only one PCIe socket. Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: ClearFog renamed upstream to ClearFog ProMarko Ratkaj2017-05-145-11/+11
| | | | | | The conventional model is now known as the "Clearfog Pro" Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: ClearFog DT file renamed upstreamMarko Ratkaj2017-05-141-0/+80
| | | | | | | The conventional model is now known as the "Clearfog Pro". We keep the old armada-388-clearfog.dts file for compatibility reasons. Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* Revert "mvebu: remove linux 4.4 support"Felix Fietkau2017-04-1779-0/+14294
| | | | | | | | This reverts commit 51397d7d95d9f5e210a5557f65de1fa21e6f5921. There are some unresolved random crashes on WRT1900AC v1 that still need to be sorted out Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: remove linux 4.4 supportFelix Fietkau2017-04-1279-14294/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: update kernel 4.9 to 4.9.17Hauke Mehrtens2017-03-266-14/+14
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update kernel 4.9 to 4.9.14Hauke Mehrtens2017-03-124-12/+3
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: wrt3200acm enable SDIO interfaceHenryk Heisig2017-03-112-0/+11
| | | | | | add mwifiex-sdio package to wrt3200acm Signed-off-by: Henryk Heisig <hyniu@o2.pl>
* mvebu: add default sata triggerAnsuel Smith2017-03-083-0/+60
| | | | | | | | | | | Change dts file to add default sata trigger to sata led. Backport upstream accepted patch to add sata trigger to device tree source files already upstreamed. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [backport upstream accepted patch] Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: enable disk led triggerAnsuel Smith2017-03-081-0/+1
| | | | | | As we have a disk led we enable the disk trigger that work with the easata port Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* mvebu: add linux 4.9 supportFelix Fietkau2017-02-1662-1/+9799
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: append metadata to clearfog sd card imagesJonas Gorski2017-02-131-1/+1
| | | | | | | | | | | | | | Fixes the following issue: root@LEDE:/# sysupgrade /tmp/lede-mvebu-armada-388-clearfog-sdcard.img.gz Saving metaconfig... Image metadata not found Use sysupgrade -F to override this check when downgrading or flashing to vendor firmware Image check 'fwtool_check_image' failed. root@LEDE:/# Acked-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar71xx/ipq806x/mediatek/mvebu: fix network defaultsJo-Philipp Wich2017-02-071-2/+2
| | | | | | | | | | | After "73d923e base-files: emit tagged switch configuration by default" some default network configurations are broken because the lan and wan ifnames are forcibly set to untagged netdevs. Adjust the offending set_interfaces_lan_wan() calls to use the proper tagged device names. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mvebu: fix usb port ledsMathias Kresin2017-02-011-10/+15
| | | | | | | | | | | | | | | | | | | All mvebu boards have three USB LEDs. The first one is used for the USB1 port. There are two LEDs related to the second USB port. The top (bar) LED gets bright in case any USB device is connected to the second USB port. If the connected device is an USB 3 (SuperSpeed) device, the small dot LED bellow the "bar" LED gets also bright. While at it, use a name for the USB LEDs that matches the names printed on the case. Fixes: FS#423, FS#425 Signed-off-by: Kabuli Chana <newtownbuild@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: put u-boot images into image staging directoryJo-Philipp Wich2017-01-271-1/+1
| | | | | | | | | | | | Do not put the u-boot images into the kernel build directory as this directory might get removed after kernel updates while the u-boot packages InstallDev recipe is not getting re-executed because it is still considered current, leading to image build failures later on due to missing u-boot images. To ensure that built bootloader images persist over kernel version updates in the buildroot, put them into the new STAGING_DIR_IMAGE directory. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mvebu: set fan_ctrl.sh only on mambaHans Geiblinger2017-01-242-1/+23
| | | | | Signed-off-by: Hans Geiblinger <cybrnook2002yahoo.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
* uboot-mvebu: switch to u-boot.mkFelix Fietkau2017-01-242-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: simplify etc/board.d/02_networkPaul Wassi2017-01-132-9/+5
| | | | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at> [Álvaro]: also change WAN LEDs Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: several fixes for Linksys WRT3200ACMÁlvaro Fernández Rojas2017-01-131-44/+40
| | | | | | | | - Fix WLAN LEDs definition. - Fix USB pinctrl definition. - Remove SDHCI definition. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: remove the clearfog-bundleFelix Fietkau2017-01-131-13/+1
| | | | | | It is obsoleted by proper SD card image support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: work around an ethernet tx scheduling fairness issueFelix Fietkau2017-01-111-0/+36
| | | | | | | | | | | The hardware queue scheduling is apparently configured with fixed priorities, which creates a nasty fairness issue where traffic from one CPU can starve traffic from all other CPUs. Work around this issue by forcing all tx packets to go through one CPU, until this issue is fixed properly. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Fix up some leds on this seriesKabuli Chana2017-01-102-5/+5
| | | | | | correct ports, fix power led on rango, tested mamba,shelby,rango Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* kernel: remove ubifs xz decompression supportFelix Fietkau2017-01-091-2/+0
| | | | | | | It has been unused, and less useful than squashfs for cases where flash space usage matters. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: fix sysupgrade for Linksys WRT3200ACMVignesh Balasubramaniam2016-12-041-1/+1
| | | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
* mvebu: fix image validation errorMathias Kresin2016-12-041-2/+2
| | | | | | | | The name from the Device define will be used in the metadata. Due to typo/different spelling, this name might not match the one exported in /lib/mvebu.sh. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: fix typo in image metadata supportMathias Kresin2016-11-271-2/+2
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "mvebu: simplify etc/board.d/02_network"Felix Fietkau2016-11-251-1/+5
| | | | | | | This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d. According to reports, this introduces a regression on WRT3200ACM Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: simplify etc/board.d/02_networkPaul Wassi2016-11-241-5/+1
| | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* mvebu: use image metadata for firmware validationFelix Fietkau2016-11-242-22/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Add BQL patch for mvneta driver.Toke Høiland-Jørgensen2016-11-211-0/+83
| | | | | | | | This adds the patch submitted to upstream that adds BQL to the mvneta driver: https://patchwork.kernel.org/patch/9328413/. Helps latency under load when the physical link is saturated. Signed-off-by: Toke Høiland-Jørgensen <toke@toke.dk>
* mvebu: revert remove of mvsw61xx device tree nodesMathias Kresin2016-11-132-0/+53
| | | | | | | | | | The marvell,88e6352 and marvell,88e6172 compatible strings are used in target/linux/generic/files/drivers/net/phy/mvsw61xx.c. No idea why grep missed them when I searched for them. Thanks to Syrone Wong for noticing and reporting my mistake. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: dts: fix dtc compiler warningsMathias Kresin2016-11-122-53/+0
| | | | | | | | | | | Fixes invalid device tree parameters. Drop the mvsw61xx node used in mvebu device tree source files. It looks like some kind of ethernet switch cargo cult. Neither the marvell,88e6352 nor the marvell,88e6172 compatible strings can be found in any LEDE file or in the kernel sources. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update kernel 4.4 to version 4.4.30Stijn Segers2016-11-021-2/+2
| | | | | | | | | | This patch bumps the 4.4 kernel from .28 to .30 and refreshes the patches. Compile-tested on ar71xx, x86/64, ramips/mt7621, brcm47xx and kirkwood. Run-tested on ar71xx & ramips/mt7621, brcm47xx and kirkwood (last two confirmed by P. Wassi). Signed-off-by: Stijn Segers <francesco.borromini@inventati.org>
* mvebu: add support for the Linksys WRT3200ACM (Rango)Imre Kaloz2016-10-2411-16/+491
| | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2Imre Kaloz2016-10-241-1/+8
| | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
* switch to the new usbport LED triggerRafał Miłecki2016-10-191-1/+1
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mvebu: fix sysupgradeAaron Curley2016-10-041-0/+2
| | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Fixes FS#197. Signed-off-by: Aaron Curley <accwebs@gmail.com>
* kernel: update to v4.4.23Álvaro Fernández Rojas2016-09-301-9/+9
| | | | | | | Refresh patches for all targets that support kernel 4.4. compile/run-tested on brcm2708/bcm2710 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: add support for SFPJonas Gorski2016-09-2930-0/+6212
| | | | | | | | Add patches for SFP support and package it for ClearFog. Tested with a Juniper SFP module. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: disable MSI interruptsJonas Gorski2016-09-291-2/+0
| | | | | | | | | | | | | | | | MSI interrupts do not seem to be working on mvebu, and they break ath10k. Since nothing else seems to be using them, especially not mwlwifi, disable them until we can fix MSI interrupts. Works around the following issue: [ 9.001457] ath10k_pci 0000:02:00.0: failed to receive control response completion, polling.. [ 10.001453] ath10k_pci 0000:02:00.0: Service connect timeout [ 10.007126] ath10k_pci 0000:02:00.0: failed to connect htt (-110) [ 10.092224] ath10k_pci 0000:02:00.0: could not init core (-110) [ 10.098177] ath10k_pci 0000:02:00.0: could not probe fw (-110) Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add switch config for clearfog proJonas Gorski2016-09-261-0/+3
| | | | | | Check for switch0 existance and add default switch config if found. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: add sysupgrade support for clearfogJonas Gorski2016-09-265-8/+79
| | | | | | | | Add and enable sysupgrade support for clearfog boards, based on how the brcm2708 target does it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add switch node to clearfogJonas Gorski2016-09-262-1/+22
| | | | | | | | Add a switch node to clearfog to probe and initialize it on Clearfog Pro. This make the switch work and allows using all six switch ports. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>