aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mvebu/base-files
Commit message (Collapse)AuthorAgeFilesLines
* mvebu: use device-tree board detectionTomasz Maciej Nowak2019-05-1113-171/+68
| | | | | | | | Convert whole target to Device Tree based board detection instead of identifying devices by dts file name. With this we can drop mvebu.sh translation script and rely on common method for model detection. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: fix board_name condition in 79_move_configKlaus Kudielka2019-05-111-1/+1
| | | | | | | The correct board_name for the Turris Omnia is armada-385-turris-omnia. Fixes: 4e8345ff68 ("mvebu: base-files: autodetect upgrade device") Signed-off-by: Klaus Kudielka <klaus.kudielka@gmail.com>
* mvebu: sysupgrade: sdcard: keep user added partitonsTomasz Maciej Nowak2019-04-062-6/+77
| | | | | | | | Currently sysupgrade overwrites whole disk and destroys partitions added by user. Sync the sysupgrade code with the one present in x86 target to remedy this behaviour. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: base-files: autodetect upgrade deviceTomasz Maciej Nowak2019-04-062-10/+18
| | | | | | | Since some boards could be also booted from other mediums than SD card, lets make the upgrade block device autodetected. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: shrink amount of packages and reorganize themTomasz Maciej Nowak2019-04-061-4/+10
| | | | | | | | | Since most of devices using SD card image to boot, use ext4 as boot files system we can drop fat fs related packages. Also move packages which are added repeatedly across subtargets to their default packages, with droping the ones that are enabled in target kernel configugation. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: Fix typo in MACCHIATOBin detectionHauke Mehrtens2019-03-251-1/+1
| | | | | | The name in the device tree file is written with two C. Signed-off-by: Hauke Mehrtens <hauke.mehrtens@intel.com>
* mvebu: initial support for Marvell Armada 7k and 8k DB boardsDamir Samardzic2018-05-212-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for cortex-a72 based Armada DB-88F8040-Modular and DB-88F7040-Modular development boards. DB-88F8040-Modular specifications: - Quad-core ARMv8 Cortex A72 CPU (up to 2 GHz) - DDR4 DIMM - 64 bits + ECC - 2 x 128 Mb SPI NOR flash memory - 2 x 1G Ethernet port via RGMII (RJ45) - 2 x SD card ports (4 bit port on CP, 8 bit port on AP) - 2 SERDES modules with the following interfaces each: - 2 x SATA Rev 3.0 port (Port1 via SERDES module CON4 (active port), Port0 via SERDES Module CON2 or CON1 (optional port)) - 3 x PCI Express (PCIe) Gen 3.0 (Port2 via SERDES module CON5 (active port), Port1 via SERDES module CON7 (optional port), Port0 via SERDES module CON6 (optional port)) - 2 x USB3 (USB 2.0 backward compatible) host (via SERDES module CON9 and CON10) - 1 x 10G port over SFP+ connector (via SERDES module CON8) - 1 x MCI interface by two over USB Type C connector - 4 x serial COM port driven by the 88F8040 UART interface and converted to USB via FTDI IC - I2C Master Interface - CP I2C 2x EEPROM @ Address 0x50 and 0x57 - 1 x I/O Expander @ Address 0x21 - Sample at Reset (SatR) memory device @ Address 0x4C and 0x4E - I2C Slave Interface (via SERDES module) - Connection to each device on the board via an I2C multiplexer - JTAG interface for CPU emulator - Board dimensions: 270 mm x 240 mm (main + SERDES module) - SERDES Module Dimensions: 70 mm x 105 mm DB-88F7040-Modular specifications: - Quad-core ARMv8 Cortex A72 CPU - CPU core operating speed of up to 1.6 GHz for Dual Core, 1.4 GHz for Quad Core - DDR4 - 32 bit + ECC on Module - SLM1366-V1 (DB-DDR4-40B-MODULE) 4 GByte 32-bit - 1 x 128Mb SPI NOR flash memory - 2 x 1G Ethernet port: 1 over RGMII (RJ45) and 1 over SGMII - SD card 4 bits port on AP - eMMc Module on CP - 1 SERDES Modules with the following interfaces each: - 1 x SATA Rev 3.0 port (via SERDES module CON4) - 1 x PCI Express (PCIe) Gen 3.0 (via SERDES module CON5) - 2 x USB 3.0 (USB 2.0 backward compatible) host (via SERDES module CON9 and CON10) - 1 x 10G port over SFP+ connector (via SERDES module CON8) - 2 x MCi interface by one over USB Type C connector - 4 x Serial COM port driven by the 88F7040 UA - RT interface and converted to USB via FTDI IC - I2C Master Interface - 2 x EEPROM at address 0x57 and 0x50 in AP and 2 x EEPROM at address 0x57 and 0x50 in CP - 1 x I/O Expander at address 0x21 - Sample at Reset (SatR) memory device at address 0x4C and 0x4E - I2C Slave Interface (via SERDES module) - Connection to each device on the board via an I2C multiplexer - JTAG interface for CPU emulator - Board dimensions - 270 mm x 240 mm (main + SERDES module) - SERDES Module Dimensions - 70 mm x 105 mm Booting from USB flash drive (dd sdcard image to the flash drive): 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot manually (make sure to set correct dtb file name): setenv bootargs_root 'root=/dev/sda2 rw rootdelay=2 ip=dhcp' setenv fdtfile armada-7040-db.dtb setenv image_name Image setenv bootcmd 'usb start; ext4load usb 0:1 $kernel_addr $image_name; ext4load usb 0:1 $fdt_addr $fdtfile; setenv bootargs $console $mtdparts $bootargs_root; booti $kernel_addr - $fdt_addr' saveenv boot Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: initial support for Marvell Armada 3720 DB boardDamir Samardzic2018-05-212-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Marvell Armada cortex-a53 based DB-88F3720-DDR3-Modular development board. Specifications: - Dual core ARMv8 Cortex-A53 CPU (up to 1.0 GHz) - 4Gb 16-bit DDR3/3L DRAM memory - 128Mb SPI NOR flash memory - 8Gb eMMC NAND flash memory - 1 x SATA Rev 3.0 port - 1 x PCI Express (PCIe) Gen 2.0 or 1 x mini PCI Express (PCIe) Gen 2.0 - 1 x 1G Ethernet port via RGMII (RJ45) - 1 x SD card port - 1 x USB3 (USB2 backward) host\device port via type C connector - 1 x USB2 host port via type A connector - 1 x serial COM port driven by the 88F3720 UART interface and converted to USB via FTDI IC (option to connect the UART DB9 adapter) - I2C Master Interface: - 1 x EEPROM @ address 0x57 - 1 x I/O Expanders @ address 0x22 - Sample at Reset (SatR) memory device @ address 0x4C - RTC clock generator PT7C4337AWE @ address 0x68 - USB3 switch PI5USB30213XEA @ address 0x0D - ID component of PHY module @ address 0x24 - 1 x JTAG interface for CPU emulator - 1 x SETM and JTAG debug interface - 1 x power connector for HDD supply - 1 x 12V DC jack power connector - Board dimensions: 150 mm x 179 mm - LED interface for system status Booting from SD card: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually: setenv fdt_name armada-3720-db.dtb setenv image_name Image setenv bootcmd 'mmc dev 0; ext4load mmc 0:1 $kernel_addr $image_name;ext4load mmc 0:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: add support for WRT32X (venom)Michael Gray2018-05-1410-7/+20
| | | | | | | | | | | | | | | | | | Linksys WRT32X (Venom) is identical in hardware to the WRT3200ACM with a different flash layout and boots zImage rather than uImage. Specification: - Marvell Armada 385 88F6820 (2x 1.8GHz) - 256MB of Flash - 512MB of RAM - 2.4GHz (bgn) and 5GHz (an+ac wave 2) - 4x 1Gbps LAN + 1x 1Gbps WAN - 1x USB 3.0 and 1x USB 2.0/eSATA (combo port) Flash instruction: Apply factory image via web-gui. Signed-off-by: Michael Gray <michael.gray@lantisproject.com>
* mvebu: add support for MACCHIATObin (cortex-a72)Damir Samardzic2018-03-313-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Add initial support for Marvell MACCHIATObin, cortex-a72 based Marvell ARMADA 8040 Community board. Comes in two forms: Single Shot and Double Shot. Specifications: - Quad core Cortex-A72 (up to 2GHz) - DDR4 DIMM slot with optional ECC and single/dual chip select support - Dual 10GbE (1/2.5/10GbE) via copper or SFP 2.5GbE (1/2.5GbE) via SFP 1GbE via copper - SPI Flash - 3 X SATA 3.0 connectors - MicroSD connector - eMMC - PCI x4 3.0 slot - USB 2.0 Headers (Internal) - USB 3.0 connector - Console port (UART) over microUSB connector - 20-pin Connector for CPU JTAG debugger - 2 X UART Headers - 12V input via DC Jack - ATX type power connector - Form Factor: Mini-ITX (170 mm x 170 mm) More details at http://macchiatobin.net Booting from micro SD card: 1. reset U-Boot environment: env default -a saveenv 2. prepare U-Boot with boot script: setenv bootcmd "load mmc 1:1 0x4d00000 boot.scr; source 0x4d00000" saveenv or manually: setenv fdt_name armada-8040-mcbin.dtb setenv image_name Image setenv bootcmd 'mmc dev 1; ext4load mmc 1:1 $kernel_addr $image_name;ext4load mmc 1:1 $fdt_addr $fdt_name;setenv bootargs $console root=/dev/mmcblk1p2 rw rootwait; booti $kernel_addr - $fdt_addr' saveenv Signed-off-by: Damir Samardzic <damir.samardzic@sartura.hr>
* mvebu: Get rid of RTC hack for Turris Omnia.Rosen Penev2018-03-311-1/+1
| | | | | | As Solidrun's RTC patch got merged, this hack is no longer needed. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* mvebu: new subtarget cortex A53Tomasz Maciej Nowak2018-03-103-2/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit introduces new subtarget for Marvell EBU Armada Cortex A53 processor based devices. The first device is Globalscale ESPRESSObin. Some hardware specs: SoC: Marvell Armada 3700LP (88F3720) dual core ARM Cortex A53 processor up to 1.2GHz RAM: 512MB, 1GB or 2GB DDR3 Storage: SATA interface µSD card slot with footprint for an optional 4GB EMMC 4MB SPI NOR flash for bootloader Ethernet: Topaz Networking Switch (88E6341) with 3x GbE ports Connectors: USB 3.0 USB 2.0 µUSB port connected to PL2303SA (USB to serial bridge controller) for UART access Expansion: 2x 46-pin GPIO headers for accessories and shields with I2C, GPIOs, PWM, UART, SPI, MMC, etc MiniPCIe slot Misc: Reset button, JTAG interface Currently booting only from µSD card is supported. The boards depending on date of dispatch can come with various U-Boot versions. For the newest version 2017.03-armada-17.10 no manual intervention should be needed to boot OpenWrt image. For the older ones it's necessary to modify default U-Boot environment: 1. Interrupt boot process to run U-Boot command line, 2. Run following commands: (for version 2017.03-armada-17.06 and 2017.03-armada-17.08) setenv bootcmd "load mmc 0:1 0x4d00000 boot.scr; source 0x4d00000" saveenv (for version 2015.01-armada-17.02 and 2015.01-armada-17.04) setenv bootargs "console=ttyMV0,115200 root=/dev/mmcblk0p2 rw rootwait" setenv bootcmd "ext4load mmc 0:1 ${fdt_addr} armada-3720-espressobin.dtb; ext4load mmc 0:1 ${kernel_addr} Image; booti ${kernel_addr} - ${fdt_addr}" saveenv 3. Poweroff, insert SD card with OpenWrt image, boot and enjoy. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: add support for Turris OmniaRyan Mounce2018-03-104-2/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Turris Omnia and builds an eMMC sysupgrade image in the same format as the SolidRun ClearFog. An initramfs image in the simple yet Omnia-specific 'medkit' image format is also built in order to ease the initial flashing process. Notable hardware support omissions are support for switching between SFP cage and copper PHY, and RGB LED control. Due to a current limitation of DSA, only 1/2 CPU switch uplinks are used. Specifications: - Marvell Armada 385 1.6GHz dual-core ARMv7 CPU - 1GB DDR3 RAM - 8GB eMMC Flash - 5x Gigabit LAN via Marvell 88E6176 Switch (2x RGMII CPU ports) - 1x switchable RJ45 (88E1514 PHY) / SFP SGMII WAN - 2x USB 3.0 - 12x dimmable RGB LEDs controlled by independent MCU - 3x Mini PCIe slots - Optional Compex WLE200N2 Mini PCIe AR9287 2x2 802.11b/g/n (2.4GHz) - Optional Compex WLE900VX Mini PCIe QCA9880 3x3 802.11ac (2.4 / 5GHz) - Optional Quectel EC20 Mini PCIe LTE modem Flash instructions: If the U-Boot environment has been modified previously (likely manually via serial console), first use serial to reset the default environment. => env default -a => saveenv Method 1 - USB 'medkit' image w/o serial - Copy openwrt-mvebu-turris-omnia-sysupgrade.img.gz and omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz to the root of a USB flash drive formatted with FAT32 / ext2/3/4 / btrfs / XFS. Note that the medkit MUST be named omnia-medkit*.tar.gz - Disconnect other USB devices from the Omnia and connect the flash drive to either USB port. - Power on the Omnia and hold down the rear reset button until 4 LEDs are illuminated, then release. - Wait approximately 2 minutes for the Turris Omnia to flash itself with the temporary image, during which LEDs will change multiple times. - Connect a computer to a LAN port of the Turris Omnia with a DHCP client - (if necessary) ssh-keygen -R 192.168.1.1 - ssh root@192.168.1.1 $ mount /dev/sda1 /mnt $ sysupgrade /mnt/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself and you can remove the flash drive. Method 2 - TFTP w/ serial - Extract omnia-medkit-openwrt-mvebu-turris-omnia-initramfs.tar.gz and copy dtb + zImage to your TFTP server (rename if desired) - Connect Turris Omnia WAN port to DHCP-enabled network with TFTP server - Connect serial console and interrupt U-Boot => dhcp => setenv serverip <tftp_server_ip_here> => tftpboot 0x01000000 zImage => tftpboot 0x02000000 dtb => bootz 0x01000000 - 0x02000000 - OpenWrt will now boot from ramdisk - Download openwrt-mvebu-turris-omnia-sysupgrade.img.gz to /tmp/ $ sysupgrade /tmp/openwrt-mvebu-turris-omnia-sysupgrade.img.gz - Wait another minute for the final OpenWrt image to be flashed. The Turris Omnia will reboot itself. Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: base-files: moving on from net-toolsTomasz Maciej Nowak2018-03-021-4/+4
| | | | | | | Remove dependency on net-tools, replacing calls to ifconfig with iproute equivalent, in functions changing interface MAC addresses. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: rename clearfog sysupgrade script and functionsTomasz Maciej Nowak2018-03-022-5/+5
| | | | | | | | Cosmetic name change of ClearFog sysupgrade script and its functions to more generic sdcard. This way it won't be confusing for other future device additions. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* mvebu: remove fs declaration in mount commandsTomasz Maciej Nowak2018-03-022-2/+3
| | | | | | | Allows to have other file system for boot partition without breaking sysupgrade. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-161-10/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: Migrate uci config to new PCIe pathHauke Mehrtens2018-02-131-0/+41
| | | | | | | | | | | | | | | | | | | | The name of the PCIe controller node in device tree changed between kernel 4.9 and kernel 4.14. Migrate the configuration when an update from kernel 4.9 to 4.14 or back is done to the new name to make the existing wifi configuration compatible with the new names. This replaces the "pcie-controller" part with "pcie" on all nodes if the file exists in sys fs. This is not done in the uci-defualts, because they are getting executed to late in the boot process. The kernel module gets loaded before the uci-defaults scripts are executed. When the mwlwifi driver gets loaded it will trigger an event via hotplug to detect new devices and as the paths are not in the uci configuration they will be added again. When the migration is done before the script will detect that they are already there. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mvebu: Fix ClearFog sysupgrade board definitionsRyan Mounce2017-10-151-5/+2
| | | | | | | Remove redundancy for platform_do_upgrade_clearfog Fix platform_copy_config_clearfog to reflect -base/-pro split Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* mvebu: Sort 02_network alphabeticallyRyan Mounce2017-10-151-6/+6
| | | | Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-159-25/+14
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: do board detection during preinitMathias Kresin2017-07-152-1/+9
| | | | | | Do the board detection during preinit to unify it across all targets. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: automatically handle paths and symlinks for RAMFS_COPY_BINMatthias Schiffer2017-07-111-1/+1
| | | | | | | | | | | | Depending on busybox applet selection, paths of basic utiilties may differ, and may not work as symlinks to busybox. Simply using whatever binary is found in PATH and detecting symlinks automatically is more robust and easier to maintain. The list of binaries is also slightly cleaned up and duplicates are removed. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* mvebu: fix sysupgradeMatthias Schiffer2017-06-012-18/+8
| | | | | | | | | | | | | | | | | mvebu was modifying RAMFS_COPY_BIN and RAMFS_COPY_DATA from a sysupgrade_pre_upgrade hook. As the ramfs is created from stage2, this did not have an effect anymore after the staged sysupgrade changes. As it doesn't really hurt to copy fw_printenv and fw_setenv unconditionally, simply add them in /lib/upgrade/platform.sh, so stage2 will see them. Config copying is moved to a function called by platform_copy_config, where it belongs. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> Fixes: FS#821 Fixes: 30f61a34b4cf "base-files: always use staged sysupgrade"
* mvebu: clearfog: assign SFP port to WAN zoneJosua Mayer2017-05-301-1/+1
| | | | | | | | | The single SFP port is meant for direct media access to WAN, such as VDSL2, GPON). While it could also be used for in-home fiber, it is much more likely that the LAN is standard ethernet, especially considering that SFP is the onmly port that can go beyond 1Gbps. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: clearfog: document interface configurationJosua Mayer2017-05-301-6/+9
| | | | | | | | | | | | | Take explicit note of what physical ports eth{0,1,2} refer to. Also repair port assignment: At some point between 4.9.20 and 4.9.29 the numbering changed. Keep previous port assignment that was: LAN = SFP+Switch WAN = standalone ethernet Also use the same assignment for Clearfog-Base to avoid confusion. Signed-off-by: Josua Mayer <josua.mayer97@gmail.com>
* mvebu: add ClearFog Base supportMarko Ratkaj2017-05-143-0/+9
| | | | | | | | | | Add support for SolidRun ClearFog Base board. The base model is a smaller version of ClearFog Pro without the DSA switch, replacing it with a second copper gigabit port, and only one PCIe socket. Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: ClearFog renamed upstream to ClearFog ProMarko Ratkaj2017-05-143-4/+4
| | | | | | The conventional model is now known as the "Clearfog Pro" Signed-off-by: Marko Ratkaj <marko.ratkaj@sartura.hr>
* mvebu: add linux 4.9 supportFelix Fietkau2017-02-161-0/+20
| | | | | Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ar71xx/ipq806x/mediatek/mvebu: fix network defaultsJo-Philipp Wich2017-02-071-2/+2
| | | | | | | | | | | After "73d923e base-files: emit tagged switch configuration by default" some default network configurations are broken because the lan and wan ifnames are forcibly set to untagged netdevs. Adjust the offending set_interfaces_lan_wan() calls to use the proper tagged device names. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* mvebu: fix usb port ledsMathias Kresin2017-02-011-10/+15
| | | | | | | | | | | | | | | | | | | All mvebu boards have three USB LEDs. The first one is used for the USB1 port. There are two LEDs related to the second USB port. The top (bar) LED gets bright in case any USB device is connected to the second USB port. If the connected device is an USB 3 (SuperSpeed) device, the small dot LED bellow the "bar" LED gets also bright. While at it, use a name for the USB LEDs that matches the names printed on the case. Fixes: FS#423, FS#425 Signed-off-by: Kabuli Chana <newtownbuild@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: set fan_ctrl.sh only on mambaHans Geiblinger2017-01-242-1/+23
| | | | | Signed-off-by: Hans Geiblinger <cybrnook2002yahoo.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
* mvebu: simplify etc/board.d/02_networkPaul Wassi2017-01-132-9/+5
| | | | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at> [Álvaro]: also change WAN LEDs Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: Fix up some leds on this seriesKabuli Chana2017-01-101-4/+4
| | | | | | correct ports, fix power led on rango, tested mamba,shelby,rango Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* mvebu: fix sysupgrade for Linksys WRT3200ACMVignesh Balasubramaniam2016-12-041-1/+1
| | | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
* Revert "mvebu: simplify etc/board.d/02_network"Felix Fietkau2016-11-251-1/+5
| | | | | | | This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d. According to reports, this introduces a regression on WRT3200ACM Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: simplify etc/board.d/02_networkPaul Wassi2016-11-241-5/+1
| | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* mvebu: use image metadata for firmware validationFelix Fietkau2016-11-241-21/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add support for the Linksys WRT3200ACM (Rango)Imre Kaloz2016-10-248-14/+34
| | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2Imre Kaloz2016-10-241-1/+8
| | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
* mvebu: fix sysupgradeAaron Curley2016-10-041-0/+2
| | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Fixes FS#197. Signed-off-by: Aaron Curley <accwebs@gmail.com>
* mvebu: add switch config for clearfog proJonas Gorski2016-09-261-0/+3
| | | | | | Check for switch0 existance and add default switch config if found. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: add sysupgrade support for clearfogJonas Gorski2016-09-264-7/+78
| | | | | | | | Add and enable sysupgrade support for clearfog boards, based on how the brcm2708 target does it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Configure status LED for WRT1900ACSRujun Wang2016-06-151-0/+3
| | | | Signed-off-by: Rujun Wang <chinawrj@gmail.com>
* mvebu: configure switch on WRT1200AC and WRT1900ACv2/SClaudio Leite2016-05-231-6/+4
| | | | | | Also collapses the three identical configurations into one block. Signed-off-by: Claudio Leite <leitec@staticky.com>
* mvebu: add SolidRun ClearFog A1 supportLuka Perkov2016-02-172-0/+6
| | | | | | Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr> SVN-Revision: 48736
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* mvebu: fixup wifi macs for Linksys boardsImre Kaloz2015-12-101-0/+17
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 47820
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-08 08:11:15 +0000