aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mvebu/base-files
Commit message (Collapse)AuthorAgeFilesLines
...
* mvebu: fix usb port ledsMathias Kresin2017-02-011-10/+15
| | | | | | | | | | | | | | | | | | | All mvebu boards have three USB LEDs. The first one is used for the USB1 port. There are two LEDs related to the second USB port. The top (bar) LED gets bright in case any USB device is connected to the second USB port. If the connected device is an USB 3 (SuperSpeed) device, the small dot LED bellow the "bar" LED gets also bright. While at it, use a name for the USB LEDs that matches the names printed on the case. Fixes: FS#423, FS#425 Signed-off-by: Kabuli Chana <newtownbuild@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mvebu: set fan_ctrl.sh only on mambaHans Geiblinger2017-01-242-1/+23
| | | | | Signed-off-by: Hans Geiblinger <cybrnook2002yahoo.com> Signed-off-by: Felix Fietkau <nbd@nbd.name> [cleanup]
* mvebu: simplify etc/board.d/02_networkPaul Wassi2017-01-132-9/+5
| | | | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at> [Álvaro]: also change WAN LEDs Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: Fix up some leds on this seriesKabuli Chana2017-01-101-4/+4
| | | | | | correct ports, fix power led on rango, tested mamba,shelby,rango Signed-off-by: Kabuli Chana <newtownBuild@gmail.com>
* mvebu: fix sysupgrade for Linksys WRT3200ACMVignesh Balasubramaniam2016-12-041-1/+1
| | | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Signed-off-by: Vignesh Balasubramaniam <vigneshb.hp@gmail.com>
* Revert "mvebu: simplify etc/board.d/02_network"Felix Fietkau2016-11-251-1/+5
| | | | | | | This reverts commit 539ae47103b7de5cecb1a94beab0acb97ef7df1d. According to reports, this introduces a regression on WRT3200ACM Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: simplify etc/board.d/02_networkPaul Wassi2016-11-241-5/+1
| | | | | | | Unify switch configuration on Linksys WRTxx00AC series. LAN = eth0, WAN = eth1 Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* mvebu: use image metadata for firmware validationFelix Fietkau2016-11-241-21/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mvebu: add support for the Linksys WRT3200ACM (Rango)Imre Kaloz2016-10-248-14/+34
| | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* mvebu: add missing status LEDs for Linksys WRT1200AC and WRT1900ACv2Imre Kaloz2016-10-241-1/+8
| | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org>
* mvebu: fix sysupgradeAaron Curley2016-10-041-0/+2
| | | | | | | | | | | | | | sysupgrade command fails due to missing U-Boot environment-processing binaries on sysupgrade ramdisk. The missing binaries result in the following output: Switching to ramdisk... Performing system upgrade... ash: /usr/sbin/fw_printenv: not found ash: fw_setenv: not found ash: touch: not found cannot find target partition Fixes FS#197. Signed-off-by: Aaron Curley <accwebs@gmail.com>
* mvebu: add switch config for clearfog proJonas Gorski2016-09-261-0/+3
| | | | | | Check for switch0 existance and add default switch config if found. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* mvebu: add sysupgrade support for clearfogJonas Gorski2016-09-264-7/+78
| | | | | | | | Add and enable sysupgrade support for clearfog boards, based on how the brcm2708 target does it. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com> Acked-by: Felix Fietkau <nbd@nbd.name>
* mvebu: Configure status LED for WRT1900ACSRujun Wang2016-06-151-0/+3
| | | | Signed-off-by: Rujun Wang <chinawrj@gmail.com>
* mvebu: configure switch on WRT1200AC and WRT1900ACv2/SClaudio Leite2016-05-231-6/+4
| | | | | | Also collapses the three identical configurations into one block. Signed-off-by: Claudio Leite <leitec@staticky.com>
* mvebu: add SolidRun ClearFog A1 supportLuka Perkov2016-02-172-0/+6
| | | | | | Signed-off-by: Andrej Vlasic <andrej.vlasic@sartura.hr> SVN-Revision: 48736
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-112-2/+2
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* mvebu: fixup wifi macs for Linksys boardsImre Kaloz2015-12-101-0/+17
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 47820
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
* all: remove dummy ucidef_set_interface_loopback() from board.dJo-Philipp Wich2015-12-031-2/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47744
* board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()Jo-Philipp Wich2015-12-031-2/+1
| | | | | | | | | | | | This changes uci-defaults-new.sh, config_generate and all relevant board.d files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into a single function. Also removes now superfluous enable and reset arguments. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47721
* mvebu: switch network and led config defaults to board detection frameworkJo-Philipp Wich2015-11-303-11/+24
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47674
* Revert "mvebu: migrate led and network setup to board detection framework"Jo-Philipp Wich2015-11-222-9/+9
| | | | | | | | | Roll back the mvebu conversion to board detection code as we need to fix some strcutural issues first. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47597
* mvebu: migrate led and network setup to board detection frameworkJo-Philipp Wich2015-11-202-9/+9
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47541
* mvebu: add support for the Linksys WRT1900ACS (Shelby)Imre Kaloz2015-10-088-6/+17
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 47164
* This had been set in r44508 as a workaround for switch problems.Imre Kaloz2015-08-211-2/+1
| | | | | | | | | | | | | Now that the switch driver can handle two devices with the same MAC address in separate VLANs we can go back to using the same address on both interfaces. This is the Linksys firmware's default behavior. Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46700
* mvebu: add support for the Linksys boot counterImre Kaloz2015-08-192-14/+20
| | | | | | | | | | | | | The u-boot boot counter was never reset after a successful boot, which sometimes could make some variables become out of sync. This patch adds support for the boot counter and enables auto_recovery unconditionally. Signed-off-by: Jonas Gorski <jogo@openwrt.org> Signed-off-by: Rob Mosher <nyt-openwrt@countercultured.net> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 46690
* mvebu: make flashing more safeImre Kaloz2015-05-272-1/+18
| | | | | | | | | Turn on the auto recovery feature when flashing and turn it off on successful bootup. Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45792
* mvebu: better integrate xp-gpLuka Perkov2015-04-162-0/+6
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 45459
* mvebu: add support for the Linksys Caiman and CobraImre Kaloz2015-04-167-5/+33
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45456
* mvebu: better integrate 385-ap-dbLuka Perkov2015-04-152-2/+7
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 45452
* mvebu: migrate mamba support to the upstreamed codeImre Kaloz2015-04-128-10/+10
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45400
* mvebu: handle other SKUs as wellImre Kaloz2015-04-121-2/+11
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45396
* mvebu: reformat the damaged syscfg partition on the mambaImre Kaloz2015-04-121-1/+10
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45386
* mvebu: deal with the new path in the fan control script for Linux 4.0+Imre Kaloz2015-03-311-3/+11
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 45195
* mvebu: set default regdomainImre Kaloz2015-03-201-0/+30
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 44908
* mvebu: set default WRT1900AC switch configImre Kaloz2015-02-231-1/+4
| | | | | | | | | | This sets 'enable_vlan' and thus uses 802.1q VLANs, but without tagging on either interface. Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 44509
* mvebu: set WRT1900AC WAN interface MAC addressImre Kaloz2015-02-231-1/+2
| | | | | | | | | Toggles the LA bit on the WAN interface. Signed-off-by: Claudio Leite <leitec@staticky.com> Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 44508
* targets: base-files: diag.sh does not need to be executableLuka Perkov2015-02-071-0/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44305
* targets: files in uci-defaults do not need to be executablesLuka Perkov2015-02-071-0/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44304
* mvebu: temporary el cheapo' fan control scriptImre Kaloz2015-01-262-0/+21
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 44153
* mvebu: fixups for the new driverImre Kaloz2015-01-161-3/+3
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 43978
* add "preinit_regular" diag.sh set_state argumentJohn Crispin2014-12-151-0/+3
| | | | | | | | | | | | This new argument is used right after starting regular preinit (which happens if failsafe wasn't triggered). The main purpose of "preinit" argument is to indicate that failsafe can be triggered, however we were missing a way to inform user that we don't wait for a trigger anymore. With this change it's clear when failsafe mode can be triggered. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 43715
* handle sysupgrade tar files on the WRT1900ACImre Kaloz2014-07-142-5/+34
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41647
* add sysupgrade supportImre Kaloz2014-07-133-0/+131
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41630
* enable handling of the wan led on the WRT1900ACImre Kaloz2014-07-101-1/+1
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41555
* set led triggers for the Linksys WRT1900ACImre Kaloz2014-07-011-0/+22
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41436
* drop unneeded fileImre Kaloz2014-07-011-9/+0
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41433
* use the power led on the WRT1900AC for status reportingImre Kaloz2014-06-291-0/+29
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41383
* fixup mac addresses on the WRT1900ACImre Kaloz2014-06-292-0/+29
| | | | | | Signed-off-by: Imre Kaloz <kaloz@openwrt.org> SVN-Revision: 41382
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-01 03:31:03 +0000