aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mpc85xx
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: add support for Enterasys WS-AP3710iDavid Bauer2019-12-137-0/+310
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove CONFIG_LEGACY_PTY from kernel configDaniel Golle2019-12-092-4/+0
| | | | | | Having legacy PTYs enabled causes problems with procd-hotplug. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mpc85xx: add vendor to Makefile node name, derive SUPPORTED_DEVICESAdrian Schmutzler2019-11-271-15/+13
| | | | | | | | | | | | | | By adding the vendor to the Makefile device definition node name, one can derive the standard compatible used in SUPPORTED_DEVICES instead of having to specify it manually. Despite, this moves the naming scheme closer to what is used for other targets (ath79, ramips). Build-tested on all subtargets. Run-tested on TP-Link TL-WDR4900 v1. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: correct TP-LINK TL-WDR4900 MAC addressesDavid Bauer2019-10-152-4/+4
| | | | | | | | | | | | | | This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment. Previously, the MAC addrss was read for the ethernet from the "config" partition. However, the content of this partition is dependent on the firmware which was previously installed on the device. Switch the MAC address source to the U-Boot partition, where the MAC address is always present at a fixed partition. The partition was previously already used for the WiFi MAC-addresses. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: move MAC address patch functions to common libraryAdrian Schmutzler2019-10-141-13/+2
| | | | | | | | | This unifies MAC address patch functions and moves them to a common script. While those were implemented differently for different targets, they all seem to do the same. The number of different variants is significantly reduced by this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move calibration data extraction function to libraryAdrian Schmutzler2019-10-131-29/+7
| | | | | | | | | | | | | | | | | This moves the almost identical calibration data extraction functions present multiple times in several targets to a single library file /lib/functions/caldata.sh. Functions are renamed with more generic names to merge different variants that only differ in their names. Most of the targets used find_mtd_chardev, while some used find_mtd_part inside the extraction code. To merge them, the more abundant version with find_mtd_chardev is used in the common code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [rebase on latest master; add mpc85xx] Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: provide label MAC addressAdrian Schmutzler2019-09-192-0/+2
| | | | | | | This patch adds the label MAC address for some devices in mpc85xx. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-141-4/+4
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-142-2/+2
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: correct OCEDO Panda LED definitionDavid Bauer2019-08-051-2/+2
| | | | | | | WLAN0 and the unused LED are currently swapped. Fix this, so the LED behavior matches the other OCEDo devices. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-2/+2
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mpc85xx: split up DEVICE_TITLEMoritz Warning2019-07-161-5/+12
| | | | | | Splits up DEVICE_TITLE into DEVICE_VENDOR, DEVICE_MODEL and DEVICE_VARIANT. Signed-off-by: Moritz Warning <moritzwarning@web.de>
* mpc85xx: Use gzip compressed kernel on HiveAP-330Pawel Dembicki2019-07-071-1/+1
| | | | | | | | | | | | | | | | | | | After commit 1e41de2f48 ("mpc85xx: convert TL-WDR4900 v1 to simpleImage") XZ compression of zImage was enabled. This change exposed a problem with the HiveAP-330 images, which was fixed by foregoing the compression on the kernel altogether with commit 98089bb8ba8 ("mpc85xx: Use uncompressed kernel on the HiveAP-330"). This patch adds back the gzip compression of the kernel image by utilizing the generic OpenWRT uImage method instead of relying on the PowerPC bootwrapper script that did it previously. Compile-tested: p1020/hiveap-330 Tested-by: Chris Blake <chrisrblake93@gmail.com> [run-tested] Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [filled in even more text]
* mpc85xx: Use uncompressed kernel on the HiveAP-330Chris Blake2019-06-241-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It seems that newer builds of OpenWRT have a gzip kernel larger than 2MB~, which for some reason fails to boot on this board. However, we have 8MB of kernel space and currently the uncompressed kernel is 6.5MB~, so we have some space to grow until a better solution is worked out. Before: ## Booting kernel from Legacy Image at ee840000 ... Image Name: Linux-4.19.53 Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 2315724 Bytes = 2.2 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: OpenWrt fake ramdisk Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux RAMDisk Image (uncompressed) Data Size: 0 Bytes = 0 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at ec000000 Booting using the fdt blob at 0xec000000 Uncompressing Kernel Image ... Error: Bad gzipped data GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Loading Ramdisk to 10000000, end 10000000 ... OK Loading Device Tree to 00ffa000, end 00fffc78 ... OK ft_fixup_l2cache: FDT_ERR_NOTFOUND After: ## Booting kernel from Legacy Image at ee840000 ... Image Name: POWERPC OpenWrt Linux-4.19.53 Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux Kernel Image (uncompressed) Data Size: 6724584 Bytes = 6.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Loading init Ramdisk from Legacy Image at 02000000 ... Image Name: OpenWrt fake ramdisk Created: 2019-06-22 11:17:48 UTC Image Type: PowerPC Linux RAMDisk Image (uncompressed) Data Size: 0 Bytes = 0 kB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK ## Flattened Device Tree blob at ec000000 Booting using the fdt blob at 0xec000000 Loading Kernel Image ... OK OK Loading Ramdisk to 10000000, end 10000000 ... OK Loading Device Tree to 00ffa000, end 00fffc78 ... OK Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [75 cpl limit]
* treewide: kernel: bump some targets to 4.19Petr Štetiar2019-06-181-2/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Lets bump kernel to 4.19 on targets which were run tested or got ACKed so we've enough time to make it ready for next release: armvirt/32 (runtested in qemu) armvirt/64 (runtested in qemu) ath79/generic (runtested on Carambola2) gemini/generic (runtested on DIR-685, DNS-313, SQ201, SL93512R) imx6/generic (runtested on Apalis) ipq40xx/generic (runtested on nbg6617) malta/be64 (runtested in qemu) malta/be (runtested in qemu) malta/le (runtested in qemu) malta/le64 (runtested in qemu) mpc85xx/generic (runtested on TL-WDR4900) mpc85xx/p2020 (runtested on P2020RDB) mvebu/cortexa53 mvebu/cortexa72 mvebu/cortexa10 octeon/generic (runtested on EdgeRouter Lite) sunxi/cortexa53 (build tested only) sunxi/cortexa7 (runtested on Lime2-K) sunxi/cortexa8 (build tested only) tegra/generic x86/64 (runtested in qemu) Acked-by: Zoltan HERPAI <wigyori@uid0.hu> [sunxi] Tested-by: Linus Walleij <linus.walleij@linaro.org> [gemini] Tested-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [mvebu, tegra] Tested-by: Daniel Engberg <daniel.engberg.lists@pyret.net> [octeon] Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [mpc85xx/generic mpc85xx/p2020] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 4.19 to 4.19.50Koen Vandeputte2019-06-121-14/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.125 (FS#2305 FS#2297)Koen Vandeputte2019-06-122-15/+4
| | | | | | | | | | | | | | | | Refreshed all patches. This bump contains upstream commits which seem to avoid (not properly fix) the errors as seen in FS#2305 and FS#2297 Altered patches: - 403-net-mvneta-convert-to-phylink.patch - 410-sfp-hack-allow-marvell-10G-phy-support-to-use-SFP.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: re-enable TL-WDR4900v1 imagesPawel Dembicki2019-06-101-1/+1
| | | | | | | | | This reverts commit 324e94f31bfd ("mpc85xx: disable bricking TL-WDR4900v1 images") The previous commit fixes the TL-WDR4900v1. Enable the target again. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: convert TL-WDR4900 v1 to simpleImageChristian Lamparter2019-06-106-212/+106
| | | | | | | | | | | | | | | | | Converts the TP-Link WDR4900 v1 to use the simpleImage in the hopes of prolonging the life of the device. While at it, the patch makes the fdt.bin an ARTIFACT and sets the KERNEL_SIZE to 2684 KiB as a precaution since the stock u-boot is using a fixed kernel size. Note: Give the image some time, it will take much longer to extract and boot. [tested for 4.14/4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Co-authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* build: add a config option for enabling a testing version of the target kernelFelix Fietkau2019-05-111-0/+1
| | | | | | | If the target supports a newer kernel version that is not used by default yet, it can be enabled with this option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* layerscape: unbreak ehci-fsl interaction with mpc85xxChristian Lamparter2019-04-151-1/+1
| | | | | | | | | | Both targets have their own idea of how to use ehci-fsl. This patch reverts part of commit 68b8d3b0796d ("kernel: usb: add FSL EHCI package") and moves ehci-fsl back into kmod-usb2, while also making it hopefully useable for the mpc85xx target. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: disable bricking TL-WDR4900v1 imagesChristian Lamparter2019-04-151-1/+1
| | | | | | | | | | | | | | | | | | The current mpc85xx build is failing because the TL-WDR4900v1 kernel image no longer fits into the partition. Extending the kernel is not possible without updating u-boot's kernel loader commands. This patch disables the WDR4900v1 until the kernel image size issue is fixed so the buildbot can still compile the Sophos RED 15w Rev.1 . Installing the WDR4900v1 images would cause the routers to get bricked. For the discussion, please go to: <https://github.com/openwrt/openwrt/pull/1773> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: generic: Check kernel size for the TL-WDR4900Pawel Dembicki2019-04-131-0/+1
| | | | | | | | | | | TP-Link TL-WDR 4900 have u-boot with read-only env. Boot command read only 0x29F000 data from flash. Bigger images causes crc error. It can't be changed. This patch add kernel size checking. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [utilize KERNEL_SIZE]
* mpc85xx: clean up device package selectionDavid Bauer2019-04-131-4/+2
| | | | | | | Remove wireless and USB packages from the device-specific package selection as they are already selected by the target itself. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove USB support from kernelDavid Bauer2019-04-133-15/+1
| | | | | | | | | | | | This removes USB support from the compiled kernel. Because of this, the kernel is just small enough for the TP-Link WDR4900 to boot the resulting kernel. This is necessary to support the WDR4900 in the upcoming 19.xx release. In the long run, this should be fixed with a second stage bootloader, as the vendor bootloader only loads the first 2684k bytes. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.110Koen Vandeputte2019-04-081-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: Fix Aerohive HiveAP-330 initramfs imageChris Blake2019-03-021-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | At some point our initramfs image grew over 6MB, which is causing an issue when uncompressing in the stock bootloader: => bootm 0x5000000 - 0x1000000; Image Name: Linux-4.19.24 Created: 2019-02-23 1:58:20 UTC Image Type: PowerPC Linux Kernel Image (gzip compressed) Data Size: 6752470 Bytes = 6.4 MB Load Address: 00000000 Entry Point: 00000000 Verifying Checksum ... OK Booting using the fdt blob at 0x1000000 Uncompressing Kernel Image ... Error: inflate() returned -5 GUNZIP: uncompress, out-of-mem or overwrite error - must RESET board to recover Loading Device Tree to 00ffa000, end 00fffc78 ... OK To get around this, we need to move to an uncompressed image for the initramfs image. While this makes a larger image, it is thankfully bootable so people can then convert their devices to run OpenWRT. It's worth noting the non-initramfs image is under 3M, so it will be ages before we have any issues with the flashed kernel. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [keep commit message at less than 75 characters per line]
* mpc85xx: 4.19: add missing symbolPawel Dembicki2019-02-141-0/+1
| | | | | | | | OCEDO Panda was added in b368373f, but only for 4.14 config. This patch fix 4.19 build for generic and p2020 subtarget. Signed-off-by: Pawel Dembicki <p.dembicki@wb.com.pl>
* kernel: bump 4.19 to 4.19.18Koen Vandeputte2019-01-281-8/+4
| | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 031-v5.0-MIPS-BCM47XX-Setup-struct-device-for-the-SoC.patch - 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch Removed upstreamed hunk in: - 800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.96Koen Vandeputte2019-01-281-8/+4
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed patches: - 142-jffs2-Fix-use-of-uninitialized-delayed_work-lockdep-.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: add support for OCEDO PandaDavid Bauer2019-01-2611-0/+472
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: FSL P1020 (2x 800MHz E500 PPC) RAM: 1GB DDR3 FLASH: 256MiB NAND WiFi: 2x Atheros AR9382 2x2:2 abgn ETH: 2x BCM54616S - 1x BCM53128 8-port switch LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS) BTN: 1x RESET Installation ------------ 1. Download initrams kernel image, dtb binary and sysupgrade image. 2. Place initramfs kernel into tftp root directory. Rename to "panda-uimage-factory". 3. Place dtb binary into tftp root directory. Rename to "panda.fdt". 4. Start tftp server on 192.168.100.8/24. 5. Power up the device with the reset button pressed. It will download the initrams and dtb via tftp and boot into OpenWRT in RAM. 6. SSH into the device and remove the factory partitions. > ubirmvol /dev/ubi0 --name=kernel1 > ubirmvol /dev/ubi0 --name=rootfs1 > ubirmvol /dev/ubi0 --name=devicetree1 You will have around 60 MiB of free space with that. You can also delete "kernel2", "devicetree2", "rootfs2" and "storage" respectively in case you do not want to go back to the vendor firmware. 7. Modify the U-Boot bootcmd to allow for booting OpenWRT > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel && bootm 0x1000000" > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200 ubi.mtd=3,2048" > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt" 8. Transfer the sysupgrade image via scp into the /tmp directory. 9. Upgrade the device > sysupgrade -n /tmp/<imagename> Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: use generic diag.shDavid Bauer2019-01-264-46/+23
| | | | | | | | | | | | | This commit removes the target-specific diag.sh script. This way, the generic one is used for the target, which uses DT-aliases to specify the LEDs used. This way, we are also able to use different LEDs to indicate different states. We use green status LEDs for indicating boot and a running system. Where possible, the red status LED is used to indicate failsafe mode and a running upgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.19 to 4.19.16Stijn Tintel2019-01-171-8/+8
| | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch - backport/096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch - backport/424-v4.20-net-dsa-fix-88e6060-roaming.patch - hack/100-mtd-rawnand-qcom-fix-memory-corruption-that-causes-p.patch - pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch Update patch that no longer applies: - backport/343-netfilter-nft_flow_offload-handle-netdevice-events-f.patch Compile-tested: mesongx Runtime-tested: mesongx Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.14 to 4.14.93Stijn Tintel2019-01-141-2/+2
| | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch - pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch - brcm2708/950-0415-qmi_wwan-apply-SET_DTR-quirk-to-the-SIMCOM-shared-de.patch Compile-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64 Runtime-tested: ar71xx, ath79, brcm2708/bcm27{08,10}, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-1314-3/+419
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: disable initramfs image in TL-WDR4900Pawel Dembicki2019-01-131-0/+1
| | | | | | | | | | Initramfs image isn't required for this device and regular initramfs generation isn't work properly. It create not working binaries. This patch disable initramfs image for TL-WDR4900. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mpc85xx: add support for Freescale (NXP) P2020RDBPawel Dembicki2019-01-137-1/+411
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit add initial support for Freescale (NXP) P2020RDB Hardware: SoC: P2020 2x1GHz DRAM: 512-1GB DDR3 2 + 4 GBE (2 separate ports and four in VSC7385) Flash: 16MB NOR, 32MB NAND, 16MB SPI-NOR PCIE x1 and mPCIE x1 SD Reader Interfaces: GBE RJ45 x6 USB2.0 x1 UART x2 I2C x2 JTAG x1 SD x1 PCIE x2 (PCIE and mPCIE) Flash instructions: Place sysupgrade image to 0x80000 address in NOR. Eg. (no brakelines in setenv command): setenv 'firmware_flash tftpboot $loadaddr $firmwarefile; protect off $norfdtaddr +$filesize; erase $norfdtaddr +$filesize; cp.b $loadaddr $norfdtaddr $filesize; protect on $norfdtaddr +$filesize; cmp.b $loadaddr $norfdtaddr $filesize' setenv firmwarefile firmware.bin run firmware_flash Boot (no brakeline in setenv command): setenv bootcmd 'setenv bootargs root=/dev/mtdblock3 rw console=$consoledev, $baudrate rootfstype=squashfs $othbootargs; bootm $norfdtaddr' saveenv boot Known issues: -Switch is unmanaged (VSC 7385 is connected via eLBC, driver uses SPI) -No SD reader support Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [refreshed patches]
* mpc85xx: 4.19: refresh kernel configChristian Lamparter2019-01-051-67/+29
| | | | | | | This patch syncs the 4.19 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: 4.14: refresh kernel configChristian Lamparter2019-01-051-19/+24
| | | | | | | This patch syncs the 4.14 kernel config to the current generic configuration. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add kernel 4.19 supportPawel Dembicki2019-01-055-0/+526
| | | | | | | | | | | | | | | Copied config from 4.14 Add patches for 4.19 Drop patch 103-powerpc-fix-build-cross32ar.patch, because issue was fixed in upstream. Compiled: generic p1020 Compiled and tested: (unofficial) P2020, TP-Link TL-WDR4900 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* mpc85xx: tl-wdr4900-v1: convert to mtdsplit imagePawel Dembicki2019-01-053-52/+62
| | | | | | | | | | | | | | | Currently, the image creation process for the TP-Link tl-wdr4900-v1 needs a fixed sized kernel and places the rootfs partition at a fixed offset. With the upcoming move to 4.19 the kernel will no longer fit into the existing allocated space for the kernel partition. This patch converts the device to utilize the established tplink,firmware mtdsplitter, which can deal with a dynamic kernel/rootfs size. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* mpc85xx: workaround 4.14 cross compile issueRyan Mounce2018-10-201-0/+10
| | | | | | | | | | | Regression introduced with 4.10 by 43c9127d94d62a232ed33ed2eab8a08657ce5472 Build will fail if system 'ar' does not support deterministic builds. e.g. macOS with Xcode toolchain Appears to be fixed upstream in 4.18 by af3901cbbd3de182aafb8ee553c825c0074df6a2 Signed-off-by: Ryan Mounce <ryan@mounce.com.au>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-162-3/+3
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kernel: bump 4.14 to 4.14.76Koen Vandeputte2018-10-164-29/+29
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* mpc85xx: remove kernel 4.9 supportMagnus Kroken2018-10-115-516/+0
| | | | Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* mpc85xx: switch to kernel 4.14Magnus Kroken2018-10-111-1/+1
| | | | Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* mpc85xx: add kernel 4.14 supportMagnus Kroken2018-10-115-0/+521
| | | | | | | | | Based on patches previously submitted by Achim Gottinger: http://lists.infradead.org/pipermail/openwrt-devel/2018-June/012719.html Tested on TP-Link TL-WDR4900 v1. Signed-off-by: Magnus Kroken <mkroken@gmail.com>
* treewide: replace 'linux, stdout-path' with 'stdout-path'Christian Lamparter2018-09-291-1/+1
| | | | | | | | | | | | | | | This follows a similar upstream patch by Rob Herring: |commit 78e5dfea84dc15d69940831b3981b3014d17222e |Author: Rob Herring <robh@kernel.org> |Date: Wed Feb 28 16:44:06 2018 -0600 | powerpc: dts: replace 'linux,stdout-path' with 'stdout-path' | | 'linux,stdout-path' has been deprecated for some time in favor of | 'stdout-path'. Now dtc will warn on occurrences of 'linux,stdout-path'. | Search and replace all the of occurrences with 'stdout-path'. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add migration script for TP-Link TL-WDR4900 v1 WLAN PCI pathsMatthias Schiffer2018-09-041-0/+63
| | | | | | | | | | PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9; migrate config so existing wifi-iface definitions don't break. This is implemented as a hotplug handler rather than a uci-defaults script as the migration script must run before the 10-wifi-detect hotplug handler. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* WDR4900v1 remove dt node for absent hw crypto.Tim Small2018-07-071-0/+24
| | | | | | | | | | | | | | | | | | The WDR4900v1 uses the P1040 SoC, so the device tree pulls in the definition for the related P1010 SoC. However, the P1040 lacks the CAAM/SEC4 hardware crypto accelerator which the P1010 device tree defines. If left defined, this causes the CAAM drivers (if present) to attempt to use the non-existent device, making various crypto-related operations (e.g. macsec and ipsec) fail. This commit overrides the incorrect dt node definition in the included file. See also: - https://bugs.openwrt.org/index.php?do=details&task_id=1262 - https://community.nxp.com/thread/338432#comment-474107 Signed-off-by: Tim Small <tim@seoss.co.uk>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-10 14:23:43 +0000