aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mpc85xx/p1010
Commit message (Collapse)AuthorAgeFilesLines
* generic: backport initial LEDs hw control supportChristian Marangi2023-09-041-0/+1
| | | | | | | | | | | | | | Backport initial LEDs hw control support. Currently this is limited to only rx/tx and link events for the netdev trigger but the API got accepted and the additional modes are working on and will be backported later. Refresh every patch and add the additional config flag for QCA8K new LEDs support. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org> (cherry picked from commit 0a4b309f41062ef40706162ae53b6428982a0685)
* mpc85xx: add support for Aerohive BR200-WPPawel Dembicki2023-05-142-2/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive BR200-WP router to OpenWrt under the mpc85xx/p1010 subtarget. Hardware: - SoC: Freescale P1011 - NOR: Intel JS28F512M29EWH 64MB - Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - 2x LEDs - 1x Button - PoE PSE Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; setenv serverip 192.168.1.3; tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin; bootm 0x2004000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NOR. Note: MAC assigns are taken from stock firmware: Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID -------- -------------- -------- ----- ----------- ---- ---------- ---------- --------- Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 - Eth0 08ea:44XX:XXc0 wan U - - - - - Eth1 08ea:44XX:XXc2 access D - - - hive0 - Eth2 08ea:44XX:XXc3 access D - - - hive0 - Eth3 08ea:44XX:XXc4 access D - - - hive0 - Eth4 08ea:44XX:XXc5 access D - - - hive0 - Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - - Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 - Note2: PoE PSE could be managed with `realtek-poe` package. Example port config: config port option enable '1' option id '4' option name 'lan2' option poe_plus '0' option priority '2' config port option enable '1' option id '3' option name 'lan1' option poe_plus '0' option priority '1' Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (switch@0 -> switch@10, Device's quickstart says LEDs are amber and white => add function+color properties but keep labels around, use pr_info) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add support for Enterasys WS-AP3715iDavid Bauer2023-04-082-1/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1010 (1x e500 @ 800MHz) RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9) FLASH: 32M NOR (Spansion S25FL256S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035) UART: 115200 8N1 (RJ-45 Cisco) Installation ------------ 1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in the root directory of a TFTP server and serve it at 192.168.1.66/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Alter the bootcmd in U-Boot: $ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm" $ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000; bootm 0x2000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Boot the initramfs image $ run ramboot_openwrt 5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: fix incorrect kernel targetDavid Bauer2023-03-201-1/+1
| | | | | | | | | | | | | | | The wrapper-image for the WL-WDR4900 was used as a build-target for the kernel. This workd fine as long as only a single wrapper is used with the OpenWrt build-system. If additional wrappers are used, the build becomes racy in the wrapper-stage. The wrapper images actually do not represent a target. They are built based on the kernel configuration. Only copy the resulting images to avoid race-conditions as explained. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Watchguard Firebox T10David Bauer2023-03-071-0/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Freescale P1010 RAM: 512MB FLASH: 1 MB SPI-NOR 512 MB NAND ETH: 3x Gigabite Ethernet (Atheros AR8033) SERIAL: Cisco RJ-45 (115200 8N1) RTC: Battery-Backed RTC (I2C) Installation ------------ 1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI programmer. The SHA1 hash for the U-Boot password is currently unknown. A tool for patching U-Boot is available at https://github.com/blocktrron/t10-uboot-patcher/ You can also patch the unknown password yourself. The SHA1 hash is E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA 2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears. The patched password is '1234' (without quotation marks) 3. Download the OpenWrt initramfs image. Copy it to a TFTP server reachable at 10.0.1.13/24 and rename it to uImage. 4. Connect the TFTP server to ethernet port 0 of the Watchguard T10. 5. Download and boot the initramfs image by entering "tftpboot; bootm;" in U-Boot. 6. After OpenWrt booted, create a UBI volume on the old data partition. The "ubi" mtd partition should be mtd7, check this using $ cat /proc/mtd Create a UBI partition by executing $ ubiformat /dev/mtd7 -y 7. Increase the loadable kernel-size of U-Boot by executing $ fw_setenv SysAKernSize 800000 8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using scp. Install the image by using sysupgrade: $ sysupgrade -n <path-to-sysupgrade> Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might have to change the ethernet-port. 9. OpenWrt should now boot from the internal NAND. Enjoy. Signed-off-by: David Bauer <mail@david-bauer.net>
* mcp85xx: Switch TP-Link TL-WDR4900 v1 to DSAPawel Dembicki2023-02-201-0/+9
| | | | | | | | | This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch. Swconfig driver for QCA8327 switch is removed because this router is only one device which use Qualcom swconfig switch. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
* mpc85xx: enable NAND support for all subtargetsJosef Schlehofer2022-06-191-1/+0
| | | | | | | | | | | | | | In subtarget p2020, there wasn't enabled nand support, and because of that there weren't available tools from mtd-utils package, which has utilities for NAND flash memory even though reference board, which is the only currently supported device in p2020 subtarget has NAND [1]. All subtargets in mpc85xx has already enabled nand support, let's do it globally. [1] https://www.nxp.com/design/qoriq-developer-resources/p2020-reference-design-board:P2020RDB Signed-off-by: Josef Schlehofer <pepe.schlehofer@gmail.com>
* treewide: remove redundant ubifs kconfig symbolsRui Salvaterra2021-04-211-4/+0
| | | | | | | For the targets which enable ubifs, these symbols are already part of the generic kconfigs. Drop them from the target kconfigs. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* mpc85xx: add testing kernel 5.10Pawel Dembicki2021-03-011-2/+0
| | | | | | | | Subtargets p1010 and p1020 have already added. Compile and run tested on: P2020RDB Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* mpc85xx-p1010: add Kernel 5.10 supportDavid Bauer2021-02-201-0/+2
| | | | | | | | | | | | | | Tested on: Sophos RED 15W The TP-Link WL-WDR4900 needs to be disabled when 5.10 becomes the default kernel. When building with all kmods enabled, the resulting kernel image exceeds the maximum size the bootloader reads from the flash. For more information, see GitHub issue #1773 Signed-off-by: David Bauer <mail@david-bauer.net>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-101-4/+1
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-221-2/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* mpc85xx: rename generic subtarget to p1010David Bauer2020-05-183-0/+41
The mpc85xx-generic subtarget supports the QorIQ SoCs of the p1010 family. Rename the subtarget to reflect this affiliation as it's the case with the other mpc85xx subtargets. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2025-01-18 21:09:26 +0000