aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mpc85xx/base-files
Commit message (Collapse)AuthorAgeFilesLines
* mpc85xx: add support for Aerohive BR200-WPPawel Dembicki2023-05-141-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive BR200-WP router to OpenWrt under the mpc85xx/p1010 subtarget. Hardware: - SoC: Freescale P1011 - NOR: Intel JS28F512M29EWH 64MB - Memory: 2x Nanya NT5TU64M16GG-AC 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - 2x LEDs - 1x Button - PoE PSE Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; setenv serverip 192.168.1.3; tftpboot 0x2004000 openwrt-mpc85xx-p1010-aerohive_br200-wp-initramfs-kernel.bin; bootm 0x2004000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NOR. Note: MAC assigns are taken from stock firmware: Name MAC addr Mode State Chan(Width) VLAN Radio Hive SSID -------- -------------- -------- ----- ----------- ---- ---------- ---------- --------- Mgt0 08ea:44XX:XXc0 - U - 1 - hive0 - Eth0 08ea:44XX:XXc0 wan U - - - - - Eth1 08ea:44XX:XXc2 access D - - - hive0 - Eth2 08ea:44XX:XXc3 access D - - - hive0 - Eth3 08ea:44XX:XXc4 access D - - - hive0 - Eth4 08ea:44XX:XXc5 access D - - - hive0 - Wifi0 08ea:44XX:XXd0 access U 1(20MHz) - radio_ng0 - - Wifi0.1 08ea:44XX:XXd4 access D 1(20MHz) - radio_ng0 hive0 - Note2: PoE PSE could be managed with `realtek-poe` package. Example port config: config port option enable '1' option id '4' option name 'lan2' option poe_plus '0' option priority '2' config port option enable '1' option id '3' option name 'lan1' option poe_plus '0' option priority '1' Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (switch@0 -> switch@10, Device's quickstart says LEDs are amber and white => add function+color properties but keep labels around, use pr_info) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add support for Enterasys WS-AP3715iDavid Bauer2023-04-084-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1010 (1x e500 @ 800MHz) RAM: 256M DDR3 (2x Samsung K4B1G1646G-BCH9) FLASH: 32M NOR (Spansion S25FL256S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 2x Gigabit Ethernet (Atheros AR8033 / AR8035) UART: 115200 8N1 (RJ-45 Cisco) Installation ------------ 1. Grab the OpenWrt initramfs, rename it to ap3715.bin. Place it in the root directory of a TFTP server and serve it at 192.168.1.66/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Alter the bootcmd in U-Boot: $ setenv ramboot_openwrt "setenv ipaddr 192.168.1.1; setenv serverip 192.168.1.66; tftpboot 0x2000000 ap3715.bin; bootm" $ setenv boot_openwrt "sf probe 0; sf read 0x2000000 0x140000 0x1000000; bootm 0x2000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Boot the initramfs image $ run ramboot_openwrt 5. Transfer the OpenWrt sysupgrade image to the AP using SCP. Install using sysupgrade. $ sysupgrade -n <path-to-sysupgrade.bin> Signed-off-by: David Bauer <mail@david-bauer.net>
* Revert "mpc85xx: remove Watchguard T10 MAC override"David Bauer2023-04-031-0/+5
| | | | | | | | | | This reverts commit aa4a9058fbf4d2ca7ef3af9ebb5bbec896625e93. The assumption the bootloader fills out the MAC-address is not correct. The MAC-address has to be set from userspace based on information found in the device_id partition. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: remove Watchguard T10 MAC overrideDavid Bauer2023-03-201-5/+0
| | | | | | | | As the mac-address readout never worked, the mac-address fillout by the bootloader is sufficient. Remove the readout for the Watchguard T10 then. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: fix missing system importDavid Bauer2023-03-201-0/+1
| | | | | | | The mac-address accessor functions were not included in the sourced script. Fix this by importing the correct script path. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Watchguard Firebox T10David Bauer2023-03-073-1/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Freescale P1010 RAM: 512MB FLASH: 1 MB SPI-NOR 512 MB NAND ETH: 3x Gigabite Ethernet (Atheros AR8033) SERIAL: Cisco RJ-45 (115200 8N1) RTC: Battery-Backed RTC (I2C) Installation ------------ 1. Patch U-Boot by dumping the content of the SPI-Flash using a SPI programmer. The SHA1 hash for the U-Boot password is currently unknown. A tool for patching U-Boot is available at https://github.com/blocktrron/t10-uboot-patcher/ You can also patch the unknown password yourself. The SHA1 hash is E597301A1D89FF3F6D318DBF4DBA0A5ABC5ECBEA 2. Interrupt the bootmenu by pressing CTRL+C. A password prompt appears. The patched password is '1234' (without quotation marks) 3. Download the OpenWrt initramfs image. Copy it to a TFTP server reachable at 10.0.1.13/24 and rename it to uImage. 4. Connect the TFTP server to ethernet port 0 of the Watchguard T10. 5. Download and boot the initramfs image by entering "tftpboot; bootm;" in U-Boot. 6. After OpenWrt booted, create a UBI volume on the old data partition. The "ubi" mtd partition should be mtd7, check this using $ cat /proc/mtd Create a UBI partition by executing $ ubiformat /dev/mtd7 -y 7. Increase the loadable kernel-size of U-Boot by executing $ fw_setenv SysAKernSize 800000 8. Transfer the OpenWrt sysupgrade image to the Watchguard T10 using scp. Install the image by using sysupgrade: $ sysupgrade -n <path-to-sysupgrade> Note: The LAN ports of the T10 are 1 & 2 while 0 is WAN. You might have to change the ethernet-port. 9. OpenWrt should now boot from the internal NAND. Enjoy. Signed-off-by: David Bauer <mail@david-bauer.net>
* mcp85xx: Switch TP-Link TL-WDR4900 v1 to DSAPawel Dembicki2023-02-202-2/+16
| | | | | | | | | This patch introduces DSA support for TP-Link TL-WDR4900 v1 switch. Swconfig driver for QCA8327 switch is removed because this router is only one device which use Qualcom swconfig switch. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Nick Hainke <vincent@systemli.org> # TP Link WDR4900 v1 (5.15)
* mpc85xx: set WS-AP3825i mac-address in preinitDavid Bauer2022-04-261-0/+12
| | | | | | | | | The bootloader does seem to not correctly patch in the MAC address for eth0 / eth1 in some cases. While the root cause is not known, manually applying the MAC-Address in preinit does not hurt. Reported-by: Tom Herbers <freifunk@tomherbers.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: overhaul WS-AP3825i LED setupDavid Bauer2022-03-241-0/+19
| | | | | | | | | | | | As the LED controller is working now, we can make good use of the LEDs now. - Drop the model-name prefix - Rename eth0 / eth1 LEDs to LAN1 / LAN2, as they are labeled as such on the casing - Enable wired LEDs in userspace Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Extreme Networks WS-AP3825iMartin Kennedy2022-03-161-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware: - SoC: Freescale P1020 - CPU: 2x e500v2 @ 800MHz - Flash: 64MiB NOR (1x Intel JS28F512) - Memory: 256MiB (2x ProMOS DDR3 V73CAG01168RBJ-I9H 1Gb) - WiFi1: 2.4+5GHz abgn 3x3 (Atheros AR9590) - Wifi2: 5GHz an+ac 3x3 (Qualcomm Atheros QCA9890) - ETH: 2x PoE Gigabit Ethernet (2x Atheros AR8035) - Power: 12V (center-positive barrel) or 48V PoE (active or passive) - Serial: Cisco-compatible RJ45 next to 12V power socket (115200 baud) - LED Driver: TI LV164A - LEDs: (not functioning) - 2x Power (Green + Orange) - 4x ETH (ETH1 + ETH2) x (Green + Orange) - 2x WiFi (WiFi2 + WiFi1) Installation: 1. Grab the OpenWrt initramfs <openwrt-initramfs-bin>, e.g. openwrt-mpc85xx-p1020-extreme-networks_ws-ap3825i-initramfs-kernel.bin. Place it in the root directory of a DHCP+TFTP server, e.g. OpenWrt `dnsmasq` with configuration `dhcp.server.enable_tftp='1'`. 2. Connect to the serial port and boot the AP with options e.g. 115200,N,8. Stop autoboot in U-Boot by pressing Enter after 'Scanning JFFS2 FS:' begins, then waiting for the prompt to be interrupted. Credentials are identical to the one in the APs interface. By default it is admin / new2day: if these do not work, follow the OEM's reset procedure using the reset button. 3. Set the bootcmd so the AP can boot OpenWrt by executing: ```uboot setenv boot_openwrt "cp.b 0xEC000000 0x2000000 0x2000000; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go;" setenv bootcmd "run boot_openwrt" saveenv ``` If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing ```uboot setenv ipaddr <ipv4 client address>; setenv serverip <tftp server address>; tftpboot 0x2000000 <openwrt-initramfs-bin>; interrupts off; bootm start 0x2000000; bootm loados; fdt resize; fdt boardsetup; fdt chosen; bootm prep; bootm go; ``` 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. ```ash sysupgrade /tmp/<openwrt-sysupgrade-bin> ``` Notes: - We must step through the `bootm` process manually to avoid fdt relocation. To explain: the stock U-boot (and stock Linux) are configured with a very large CONFIG_SYS_BOOTMAPSZ (and the device's stock Linux kernel is configured to be able to handle it). The U-boot version predates the check for the `fdt_high` variable, meaning that upon fdt relocation, the fdt can (and will) be moved to a very high address; the default appears to be 0x9ffa000. This address is so high that when the Linux kernel starts reading the fdt at the beginning of the boot process, it encounters a memory access exception and panics[5]. While it is possible to reduce the highest address the fdt will be relocated to by setting `bootm_size`, this also has the side effect of limiting the amount of RAM the kernel can use[3]. - Because it is not relocated, the flattened device tree needs to be padded in the build process to guarantee that `fdt resize` has enough space. - The primary ethernet MAC address is stored (and set) in U-boot; they are shimmed into the device tree by 'fdt boardsetup' through the 'local-mac-address' property of the respective ethernet node, so OpenWrt does not need to set this at runtime. Note that U-boot indexes the ethernet nodes by alias, which is why the device tree explicitly aliases ethernet1 to enet2. - LEDs do not function under OpenWrt. Each of 8 LEDs is connected to an output of a TI LV164A shift register, which is wired to GPIO lines and operates through bit-banged SPI. Unfortunately, I am unable to get the spi-gpio driver to recognize the `led_spi` device tree node at all, as confirmed by patching in printk messages demonstrating spi-gpio.c::spi_gpio_probe never runs. It is possible to manually articulate the shift register by exporting the GPIO lines and stepping their values through the sysfs. - Though they do not function under OpenWrt, I have left the pinout details of the LEDs and shift register in the device tree to represent real hardware. - An archive of the u-boot and Linux source for the AP3825i (which is one device of a range of devices code-named 'CHANTRY') be found here[1]. - The device has an identical case to both the Enterasys WS-AP3725i and Adtran BSAP-2030[2] (and potentially other Adtran BSAPs). Given that there is no FCC ID for the board itself (only its WLAN modules), it's likely these are generic boards, and even that the WS-AP3725i is identical, with only a change in WLAN card. I have ordered one to confirm this. - For additional information: the process of porting the board is documented in an OpenWrt forum thread[4]. [1]: magnet:?xt=urn:btih:f5306a5dfd06d42319e4554565429f84dde96bbc [2]: https://forum.openwrt.org/t/support-for-adtran-bluesocket-bsap-2030/48538 [3]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/29 [4]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168 [5]: https://forum.openwrt.org/t/adding-openwrt-support-for-ws-ap3825i/101168/26 Tested-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Martin Kennedy <hurricos@gmail.com>
* mpc85xx: Patch HiveAP 330 u-boot to fix bootMartin Kennedy2022-02-191-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | When Kernel 5.10 was enabled for mpc85xx, the kernel once again became too large upon decompression (>7MB or so) to decompress itself on boot (see FS#4110[1]). There have been many attempts to fix booting from a compressed kernel on the HiveAP-330: - b683f1c36d8a ("mpc85xx: Use gzip compressed kernel on HiveAP-330") - 98089bb8ba82 ("mpc85xx: Use uncompressed kernel on the HiveAP-330") - 26cb167a5ca7 ("mpc85xx: Fix Aerohive HiveAP-330 initramfs image") We can no longer compress the kernel due to size, and the stock bootloader does not support any other types of compression. Since an uncompressed kernel no longer fits in the 8MiB kernel partition at 0x2840000, we need to patch u-boot to autoboot by running variable which isn't set by the bootloader on each autoboot. This commit repartitions the HiveAP, requiring a new COMPAT_VERSION, and uses the DEVICE_COMPAT_MESSAGE to guide the user to patch u-boot, which changes the variable run on boot to be `owrt_boot`; the user can then set the value of that variable appropriately. The following has been documented in the device's OpenWrt wiki page: <https://openwrt.org/toh/aerohive/hiveap-330>. Please look there first/too for more information. The from-stock and upgrade from a previous installation now becomes: 0) setup a network with a dhcp server and a tftp server at serverip (192.168.1.101) with the initramfs image in the servers root directory. 1) Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. If the password doesn't work. Try reseting the device by pressing and holding the reset button with the stock OS. 2) Once in U-Boot, set the new owrt_boot and tftp+boot the initramfs image: Use copy and paste! # fw_setenv owrt_boot 'setenv bootargs \"console=ttyS0,$baudrate\";bootm 0xEC040000 - 0xEC000000' # save # dhcp # setenv bootargs console=ttyS0,$baudrate # tftpboot 0x1000000 192.168.1.101:openwrt-mpc85xx-p1020-aerohive_hiveap-330-initramfs-kernel.bin # bootm 3) Once openwrt booted: carefully copy and paste this into the root shell. One step at a time # 3.0 install kmod-mtd-rw from the internet and load it opkg update; opkg install kmod-mtd-rw insmod mtd-rw i_want_a_brick=y # 3.1 create scripts that modifies uboot cat <<- "EOF" > /tmp/uboot-update.sh . /lib/functions/system.sh cp "/dev/mtd$(find_mtd_index 'u-boot')" /tmp/uboot cp /tmp/uboot /tmp/uboot_patched ofs=$(strings -n80 -td < /tmp/uboot | grep '^ [0-9]* setenv bootargs.*cp\.l' | cut -f2 -d' ') for off in $ofs; do printf "run owrt_boot; " | dd of=/tmp/uboot_patched bs=1 seek=${off} conv=notrunc done md5sum /tmp/uboot* EOF # 3.2 run the script to do the modification sh /tmp/uboot-update.sh # verify that /tmp/uboot and /tmp/uboot_patched are good # # my uboot was: (is printed during boot) # U-Boot 2009.11 (Jan 12 2017 - 00:27:25), Build: jenkins-HiveOS-Honolulu_AP350_Rel-245 # # d84b45a2e8aca60d630fbd422efc6b39 /tmp/uboot # 6dc420f24c2028b9cf7f0c62c0c7f692 /tmp/uboot_patched # 98ebc7e7480ce9148cd2799357a844b0 /tmp/uboot-update.sh <-- just for reference # 3.3 this produces the /tmp/u-boot_patched file. mtd write /tmp/uboot_patched u-boot 3) scp over the sysupgrade file to /tmp/ and run sysupgrade to flash OpenWrt: sysupgrade -n /tmp/openwrt-mpc85xx-p1020-aerohive_hiveap-330-squashfs-sysupgrade.bin 4) after the reboot, you are good to go. Other notes: - Note that after this sysupgrade, the AP will be unavailable for 7 minutes to reformat flash. The tri-color LED does not blink in any way to indicate this, though there is no risk in interrupting this process, other than the jffs2 reformat being reset. - Add a uci-default to fix the compat version. This will prevent updates from previous versions without going through the installation process. - Enable CONFIG_MTD_SPLIT_UIMAGE_FW and adjust partitioning to combine the kernel and rootfs into a single dts partition to maximize storage space, though in practice the kernel can grow no larger than 16MiB due to constraints of the older mpc85xx u-boot platform. - Because of that limit, KERNEL_SIZE has been raised to 16m. - A .tar.gz of the u-boot source for the AP330 (a.k.a. Goldengate) can be found here[2]. - The stock-jffs2 partition is also removed to make more space -- this is possible only now that it is no longer split away from the rootfs. - the console-override is gone. The device will now get the console through the bootargs. This has the advantage that you can set a different baudrate in uboot and the linux kernel will stick with it! - due to the repartitioning, the partition layout and names got a makeover. - the initramfs+fdt method is now combined into a MultiImage initramfs. The separate fdt download is no longer needed. - added uboot-envtools to the mpc85xx target. All targets have uboot and this way its available in the initramfs. [1]: https://bugs.openwrt.org/index.php?do=details&task_id=4110 [2]: magnet:?xt=urn:btih:e53b27006979afb632af5935fa0f2affaa822a59 Tested-by: Martin Kennedy <hurricos@gmail.com> Signed-off-by: Martin Kennedy <hurricos@gmail.com> (rewrote parts of the commit message, Initramfs-MultiImage, dropped bootargs-override, added wiki entry + link, uboot-envtools) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-061-1/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: tidy up 10-fix-wifi-macAdrian Schmutzler2020-08-131-9/+5
| | | | | | | This applies some cosmetic style fixes, mostly by removing useless echo commands. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-161-1/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mpc85xx: add support for Enterasys WS-AP3710iDavid Bauer2019-12-131-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: NXP P1020 (2x e500 @ 800MHz) RAM: 256M DDR3 (Micron) FLASH: 32M NOR (Spansion S29GL128S) BTN: 1x Reset WiFi: 1x Atheros AR9590 2.4 bgn 3x3 2x Atheros AR9590 5.0 an 3x3 ETH: 1x Gigabit Ethernet (Atheros AR8033) LED: System (green/red) - Radio{0,1} (green) LAN (connected to PHY) - GE blue - FE green Serial is a Cisco-compatible RJ45 next to the ethernet port. 115200-N-8 are the settings for OS and U-Boot. Installation ------------ 1. Grab the OpenWrt initramfs, rename it to 01C8A8C0.img. Place it in the root directory of a TFTP server and serve it at 192.168.200.200/24. 2. Connect to the serial port and boot the AP. Stop autoboot in U-Boot by pressing Enter when prompted. Credentials are identical to the one in the APs interface. By default it is admin / new2day. 3. Set the bootcmd so the AP can boot OpenWrt by executing $ setenv boot_openwrt "setenv bootargs; cp.b 0xee000000 0x1000000 0x1000000; bootm 0x1000000" $ setenv bootcmd "run boot_openwrt" $ saveenv If you plan on going back to the vendor firmware - the bootcmd for it is stored in the boot_flash variable. 4. Load the initramfs image to RAM and boot by executing $ tftpboot 0x1000000 192.168.200.200:01C8A8C0.img; bootm 5. Make a backup of the "firmware" partition if you ever wish to go back to the vendor firmware. 6. Upload the OpenWrt sysupgrade image via SCP to the devices /tmp folder. 7. Flash OpenWrt using sysupgrade. $ sysupgrade -n /tmp/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: correct TP-LINK TL-WDR4900 MAC addressesDavid Bauer2019-10-151-1/+1
| | | | | | | | | | | | | | This commit fixes TP-Link TL-WDR4900 v1 MAC address assignment. Previously, the MAC addrss was read for the ethernet from the "config" partition. However, the content of this partition is dependent on the firmware which was previously installed on the device. Switch the MAC address source to the U-Boot partition, where the MAC address is always present at a fixed partition. The partition was previously already used for the WiFi MAC-addresses. Reviewed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: move MAC address patch functions to common libraryAdrian Schmutzler2019-10-141-13/+2
| | | | | | | | | This unifies MAC address patch functions and moves them to a common script. While those were implemented differently for different targets, they all seem to do the same. The number of different variants is significantly reduced by this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move calibration data extraction function to libraryAdrian Schmutzler2019-10-131-29/+7
| | | | | | | | | | | | | | | | | This moves the almost identical calibration data extraction functions present multiple times in several targets to a single library file /lib/functions/caldata.sh. Functions are renamed with more generic names to merge different variants that only differ in their names. Most of the targets used find_mtd_chardev, while some used find_mtd_part inside the extraction code. To merge them, the more abundant version with find_mtd_chardev is used in the common code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [rebase on latest master; add mpc85xx] Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-141-4/+4
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-142-2/+2
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-2/+2
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mpc85xx: add support for OCEDO PandaDavid Bauer2019-01-263-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | CPU: FSL P1020 (2x 800MHz E500 PPC) RAM: 1GB DDR3 FLASH: 256MiB NAND WiFi: 2x Atheros AR9382 2x2:2 abgn ETH: 2x BCM54616S - 1x BCM53128 8-port switch LED: 5x LEDs (Power, WiFi1, WiFi2, N/D, SYS) BTN: 1x RESET Installation ------------ 1. Download initrams kernel image, dtb binary and sysupgrade image. 2. Place initramfs kernel into tftp root directory. Rename to "panda-uimage-factory". 3. Place dtb binary into tftp root directory. Rename to "panda.fdt". 4. Start tftp server on 192.168.100.8/24. 5. Power up the device with the reset button pressed. It will download the initrams and dtb via tftp and boot into OpenWRT in RAM. 6. SSH into the device and remove the factory partitions. > ubirmvol /dev/ubi0 --name=kernel1 > ubirmvol /dev/ubi0 --name=rootfs1 > ubirmvol /dev/ubi0 --name=devicetree1 You will have around 60 MiB of free space with that. You can also delete "kernel2", "devicetree2", "rootfs2" and "storage" respectively in case you do not want to go back to the vendor firmware. 7. Modify the U-Boot bootcmd to allow for booting OpenWRT > fw_setenv bootcmd_owrt "ubi part ubi && ubi read 0x1000000 kernel && bootm 0x1000000" > fw_setenv bootargs_owrt "setenv bootargs console=ttyS0,115200 ubi.mtd=3,2048" > fw_setenv bootcmd "run bootargs_owrt; run bootcmd_owrt" 8. Transfer the sysupgrade image via scp into the /tmp directory. 9. Upgrade the device > sysupgrade -n /tmp/<imagename> Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: use generic diag.shDavid Bauer2019-01-261-41/+0
| | | | | | | | | | | | | This commit removes the target-specific diag.sh script. This way, the generic one is used for the target, which uses DT-aliases to specify the LEDs used. This way, we are also able to use different LEDs to indicate different states. We use green status LEDs for indicating boot and a running system. Where possible, the red status LED is used to indicate failsafe mode and a running upgrade. Signed-off-by: David Bauer <mail@david-bauer.net>
* mpc85xx: add support for Sophos RED 15w Rev.1David Bauer2019-01-133-1/+35
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware ======== CPU: Freescale P1010 PowerPC RAM: 128M DDR3 NAND: 128MiB ETH: RTL8211F SGMII PHY RTL8367B 5-port RGMII switch (not connected to SoC - unmanaged) WiFi: SparkLan WPEA-121N - Atheros AR9382 2T2R abgn USB: 1x USB 2.0 LED: System, Router, Internet, Tunnel controllable LAN1-4, WAN, Power non-controllable BTN: None Installation ============ 1. Power on the device while attached to the Console port. 2. Halt the U-Boot by pressing Enter when prompted. 3. Set the correct bootcmd for booting OpenWRT: > setenv bootargs_owrt "setenv bootargs console=ttyS0,115200" > setenv bootcmd "run bootargs_owrt; nand read 0x1000000 0x300000 0x800000; bootm 0x1000000;" > saveenv 5. Rename OpenWRT initramfs image to 'kernel.bin' and place it in a TFTP server root-directory served on 192.168.1.2/24. Connect your computer to one of the LAN-ports. 4. Boot OpenWRT initramfs image with > run bootargs_owrt; tftpboot 0x1000000 192.168.1.2:kernel.bin; bootm 0x1000000; 6. (Optional) Make a Backup of 'sophos-os1', 'sophos-os2' and 'sophos-data' in case you ever want to go back to the vendor firmware. 7. Create Ubi Volume on mtd4 by executing > ubiformat /dev/mtd4 -y 8. Transfer OpenWRT sysupgrade image to the device via SCP and install it with > sysupgrade -n <openwrt-image-file> Back to Stock ============= If you want to go back to the stock firmware, here is the bootcmd of the vendor firmware: > setenv bootargs console=ttyS0,115200 root=/dev/mtdblock5; nand read 0xc00000 0x00300000 0x100000; nand read 0x1000000 0x00400000 0x00800000; bootm 0x1000000 - 0xc00000 Set it via 'setenv' from the U-Boot shell and don't forget to save it using 'saveenv'! After this, boot the OpenWRT initramfs image just like you would for installation. Write back the three vendor partitions using mtd. Reboot the device afterwards. Signed-off-by: David Bauer <mail@david-bauer.net> [refresh and reorder patches] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* mpc85xx: add migration script for TP-Link TL-WDR4900 v1 WLAN PCI pathsMatthias Schiffer2018-09-041-0/+63
| | | | | | | | | | PCI paths of the WLAN devices have changed between kernel 4.4 and 4.9; migrate config so existing wifi-iface definitions don't break. This is implemented as a hotplug handler rather than a uci-defaults script as the migration script must run before the 10-wifi-detect hotplug handler. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-161-10/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use image metadataMathias Kresin2017-10-251-90/+3
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: use the generic board detectMathias Kresin2017-10-257-53/+9
| | | | | | | | | | | | Use the values populated by the generic board detect function. The first compatible from the device tree source file will be the board name in userspace. The model property from the device tree source file will be the model name. Change the board name where used in the userspace and drop the target specific board detect, to use the generic one. Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: update HiveAP-330 dtsChris Blake2017-10-251-17/+0
| | | | | | | | | | | | | | | | | | | initramfs is not the proper name for this, as it stores a boot ramdisk and not a filesystem. Update the name to reflect it's usage correctly. If CMDLINE_OVERRIDE is enabled, the chosen bootargs aren't used at all. Drop them from the device tree source file to not cause confusion. Remove the noinitrd bootarg. Due to the empty ramdisk this parameter isn't required any longer: [ 0.000000] Initrd not found or empty - disabling initrd Use the LEDE mtd-mac-address* device tree properties to set the interfaces MAC-Addresses. Signed-off-by: Chris Blake <chrisrblake93@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: Add Aerohive HiveAP-330 Access PointChris Blake2017-10-145-5/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The following adds the Aerohive HiveAP-330 Access Point to LEDE under the mpc85xx/p1020 subtarget. Hardware: - SoC: Freescale P1020NSE2DFB - NAND: Intel JS28F512M29EWH 64MB - Memory: 2x ProMOS V59C1G01168QBJ3 128MB (Total of 256MB) - 2.4GHz WiFi: Atheros AR9390-AL1A - 5.0GHz WiFi: Atheros AR9390-AL1A - Eth1: Atheros AR8035-A PoE - Eth2: Atheros AR8035-A - TPM: Atmel AT97SC3204 - LED Driver: TI LP5521 Flashing: 1. Hook into UART (9600 baud) and enter U-Boot. You may need to enter a password of administrator or AhNf?d@ta06 if prompted. 2. Once in U-Boot, tftp boot the initramfs image: dhcp; tftpboot 0x1000000 192.168.1.101:lede- mpc85xx-p1020-hiveap-330-initramfs.zImage; tftpboot 0x6000000 192.168.1.101:lede-mpc85xx-p1020-hiveap-330.fdt; bootm 0x1000000 - 0x6000000; 3. Once booted, scp over the sysupgrade file and sysupgrade the device to flash LEDE to the NAND. sysupgrade /tmp/lede-mpc85xx-p1020-hiveap-330-sysupgrade.img Signed-off-by: Chris Blake <chrisrblake93@gmail.com>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: use the generic board_name functionMathias Kresin2017-07-154-17/+8
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: populate boardname and model earlierMathias Kresin2017-07-151-0/+0
| | | | | | | | | | | | | For targets using the generic board detection and board specific settings in diag.sh, the board name is still unset at the time the set_state() provided by diag.sh is called by 10_indicate_preinit. Change the execution order to ensure the boardname is populated before required the first time. Do the target specific board detection as early as possible, directly followed by the generic one to allow a seamless switch to the generic function for populating /tmp/sysinfo/. Signed-off-by: Mathias Kresin <dev@kresin.me>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-1/+1
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* mpc85xx: fix TL-WDR4900 mac address assignment to match original firmwareFelix Fietkau2016-02-071-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48645
* all: drop old uci-defaults.shJo-Philipp Wich2015-12-111-1/+1
| | | | | | | | | Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one and update all users accordingly. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47867
* all: remove redundant board.d/00_model filesJo-Philipp Wich2015-12-041-13/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47753
* all: remove dummy ucidef_set_interface_loopback() from board.dJo-Philipp Wich2015-12-031-2/+0
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47744
* board.d: remove redundant ucidef_set_interfaces_lan_wan() callsJo-Philipp Wich2015-12-031-1/+0
| | | | | | | | | | This removes calls to ucidef_set_interfaces_lan_wan() and ucidef_set_interfaces_lan() on boards where all relevant info can be inferred from the switch definition. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47722
* board.d: merge ucidef_add_switch() and ucidef_add_switch_ports()Jo-Philipp Wich2015-12-031-2/+1
| | | | | | | | | | | | This changes uci-defaults-new.sh, config_generate and all relevant board.d files in order combine ucidef_add_switch() and ucidef_add_switch_ports() into a single function. Also removes now superfluous enable and reset arguments. Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47721
* mpc85xx: fix typo added in r47676Jo-Philipp Wich2015-12-011-1/+1
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47681
* mpc85xx: record board id and model name in /etc/board.jsonJo-Philipp Wich2015-11-301-0/+13
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47680
* mpc85xx: convert to ucidef_add_switch_ports()Jo-Philipp Wich2015-11-301-2/+2
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47676
* mpc85xx: migrate network setup to board detection frameworkJo-Philipp Wich2015-11-201-7/+5
| | | | | | Signed-off-by: Jo-Philipp Wich <jow@openwrt.org> SVN-Revision: 47540
* mpc85xx: replace WDR4900 uci-defaults ethernet MAC address hack with DTS entryImre Kaloz2015-05-031-2/+0
| | | | | | | | | This also changes the MAC address to one of the adresses actually used by the stock firmware on one of the ethernet interfaces. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 45599
* targets: base-files: diag.sh does not need to be executableLuka Perkov2015-02-071-0/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44305
* targets: files in uci-defaults do not need to be executablesLuka Perkov2015-02-071-0/+0
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44304
* add "preinit_regular" diag.sh set_state argumentJohn Crispin2014-12-151-0/+4
| | | | | | | | | | | | This new argument is used right after starting regular preinit (which happens if failsafe wasn't triggered). The main purpose of "preinit" argument is to indicate that failsafe can be triggered, however we were missing a way to inform user that we don't wait for a trigger anymore. With this change it's clear when failsafe mode can be triggered. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 43715
* mpc85xx: fix WAN/LAN-MAC for TP-LINK TL-WDR4900 v1John Crispin2014-10-261-21/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This works around a bootloader issue where every device has the same lan/wan-mac 00:04:9f:ef:01:01 - with this patch we read the macs from config-partition during initial network setup. We have 9 valid macs stored in the partition, the 1st two are used for the radios, 3 and 4 are now used for WAN/LAN. on an already setup / running device we can get the real macs with . /lib/functions.sh . /lib/functions/system.sh echo "LAN = $(mtd_get_mac_binary config 338)" echo "WAN = $(mtd_get_mac_binary config 344)" see: https://dev.openwrt.org/ticket/14714 from the ticket / user klondike: U-Boot passed this commit https://gitorious.org/0xlab-kernel/u-boot/commit/ecd1a09b81f2ed6e6ba7bd1d0bfb0cc3d0ea2ad0 http://u-boot.10912.n7.nabble.com/U-Boot-PATCH-mpc83xx-remove-hardcoded-network-addresses-from-config-files-td44372.html I suppose to prevent this particular issue, but the WDR4900 may be using an old bootloader still affected. ^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^^ I have been checking the contents of the dtb on the flash, this particular bit is quite revealing: ethernet@b0000 { #address-cells = <0x1>; #size-cells = <0x1>; device_type = "network"; model = "eTSEC"; compatible = "fsl,etsec2"; fsl,num_rx_queues = <0x8>; fsl,num_tx_queues = <0x8>; local-mac-address = [00 00 00 00 00 00]; ^^^^^^^^^^^^^^^^^ interrupt-parent = <0x2>; phy-handle = <0x3>; phy-connection-type = "rgmii-id"; ptimer-handle = <0x4>; queue-group@0 { #address-cells = <0x1>; #size-cells = <0x1>; reg = <0xb0000 0x1000>; rx-bit-map = <0xff>; tx-bit-map = <0xff>; interrupts = <0x1d 0x2 0x1e 0x2 0x22 0x2>; }; }; I also have been checking the live device map to find this: root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b0000/local-mac-address 00000000 00 04 9f ef 01 01 |......| 00000006 root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b1000/local-mac-address * root@GHS-AP3:~# hexdump -C /proc/device-tree/soc@ffe00000/ethernet@b2000/local-mac-address * My conclussion is that U-Boot most likely finds the device and (as no valid MAC-address is provided) falls back to the default MAC provided by the old code, the kernel then receives thee modified device map from U-Boot and assumes this is the correct MAC for the device despite it obviously isn't. This can be seen at target/linux/mpc85xx/patches-3.10/140-powerpc-85xx-tl-wdr4900-v1-support.patch The enetaddr is filled up by using the device tree data by the process_boot_dtb function and used by the platform_fixups function to set the eth0 address (by calling dt_fixup_mac_address_by_alias("ethernet0", enetaddr); ). But instead we should be used the device address which to my understanding is provided in the mtd. Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com> SVN-Revision: 43074
* target/linux/*/base-files/lib/upgrade/platform.sh - wrong check for ARGCJohn Crispin2014-06-021-1/+1
| | | | | | | | | | | | | | | | | | | ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct var $# (=number of args) here. under normal conditions this had no impact, but we should at least correct it. the error was observable like this: root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh root@box:~ . /lib/upgrade/platform.sh root@box:~ . /lib/upgrade/common.sh root@box:~ platform_check_image /tmp/myfirmware.bin ash: bad number root@box:~ echo $? 0 Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com> SVN-Revision: 40915