aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.4 to 5.4.238Hauke Mehrtens2023-03-295-10/+10
| | | | | | | Compile-tested: armvirt/64, lantiq/xrx200 Run-tested: armvirt/64, lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.230Hauke Mehrtens2023-01-281-1/+1
| | | | | | | Compile-tested: x86/64 Run-tested: x86/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* generic: 5.4: refresh kernel patchesChristian Marangi2022-12-171-1/+1
| | | | | | Refresh kernel patches due to new spi nor patch. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* kernel: backport b53/bcm_sf2 changes from v5.8Rafał Miłecki2022-12-071-1/+1
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport b53/bcm_sf2 changes from v5.7Rafał Miłecki2022-12-071-2/+2
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport b53/bcm_sf2 changes from v5.6Rafał Miłecki2022-12-074-32/+32
| | | | | | This b53 backport significantly stabilizes switch traffic performance. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: backport b53/bcm_sf2 changes from v5.5Rafał Miłecki2022-12-071-1/+1
| | | | Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* kernel: bump 5.4 to 5.4.224Hauke Mehrtens2022-11-271-1/+1
| | | | | | | Compile-tested: x86/64 Run-tested: x86/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: add missing config symbolsDavid Bauer2022-11-271-0/+1
| | | | | Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 101c0c00a7143a1e50e4c0923f0af88b5176f6ed)
* kernel: bump 5.4 to 5.4.211Hauke Mehrtens2022-09-043-7/+7
| | | | | | | | | | | | | | Similar version was upstreamed: bcm27xx/patches-5.4/950-0392-tty-amba-pl011-Add-un-throttle-support.patch Manually adapted: ipq806x/patches-5.4/0063-2-tsens-support-configurable-interrupts.patch layerscape/patches-5.4/301-arch-0008-arm-add-new-non-shareable-ioremap.patch Compile-tested: x86/64 Run-tested: x86/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: mt7623: fixes kconfig for hwcryptoChukun Pan2022-07-151-1/+1
| | | | | | | | | | | The MediaTek's Crypto Engine driver has been replaced with the upstream Inside Secure's SafeXcel cryptographic engine driver, however kconfig has not been changed accordingly, this commit fixes it. Fixes: 127ad76 ("mediatek: switch over to extended upstream eip97 driver") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* mediatek: remove crypto-hw-mtk packageEneas U de Queiroz2022-07-151-23/+0
| | | | | | | | The MediaTek's Crypto Engine module is only available for mt7623, in which case it is built into the kernel. Signed-off-by: Eneas U de Queiroz <cotequeiroz@gmail.com> (cherry picked from commit 3f2d0703b60357e3ff1865783335be9f51528eb8)
* kernel: bump 5.4 to 5.4.203Hauke Mehrtens2022-07-032-3/+3
| | | | | | | | | | | | | | | Merged upstream: bcm27xx/patches-5.4/950-1014-Revert-mailbox-avoid-timer-start-from-callback.patch generic/backport-5.4/080-wireguard-0021-crypto-blake2s-generic-C-library-implementation-and-.patch Manually adapted: layerscape/patches-5.4/801-audio-0005-Revert-ASoC-fsl_sai-Add-support-for-SAI-new-version.patch oxnas/patches-5.4/100-oxnas-clk-plla-pllb.patch Compile-tested: lantiq/xrx200 Run-tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.192Hauke Mehrtens2022-05-181-1/+1
| | | | | | | Compile-tested: armvirt/64 Run-tested: armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.191Hauke Mehrtens2022-05-181-1/+1
| | | | | | | | | | | | | | | | Merged upstream: apm821xx/patches-5.4/150-ata-sata_dwc_460ex-Fix-crash-due-to-OOB-write.patch Similar patch merged upstream: bcm27xx/patches-5.4/950-0210-usb-xhci-Disable-the-XHCI-5-second-timeout.patch Manually adapted: layerscape/patches-5.4/801-audio-0008-Revert-ASoC-Remove-dev_err-usage-after-platform_get_.patch Compile-tested: armvirt/64 Run-tested: armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.179Hauke Mehrtens2022-02-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | Many changes were done in drivers/pinctrl/bcm/pinctrl-bcm2835.c between 5.4.171 and 5.4.179. The following 3 patches do not apply any more: * target/linux/bcm27xx/patches-5.4/950-0316-pinctrl-bcm2835-Add-support-for-BCM2711-pull-up-func.patch This was already integrated in kernel v5.4-rc1, it was never needed. * target/linux/bcm27xx/patches-5.4/950-0328-Revert-pinctrl-bcm2835-Pass-irqchip-when-adding-gpio.patch * target/linux/bcm27xx/patches-5.4/950-0362-pinctrl-bcm2835-Change-init-order-for-gpio-hogs.patch I think these were done to fix the problem which was really fixed in commit 75278f1aff5e ("pinctrl: bcm2835: Change init order for gpio hogs") from v5.4.175 target/linux/generic/backport-5.4/716-v5.5-net-sfp-move-fwnode-parsing-into-sfp-bus-layer.patch Move fwnode_device_is_available to the same position as in kernel 5.10. target/linux/layerscape/patches-5.4/302-dts-0083-arm64-ls1028a-qds-correct-bus-of-rtc.patch Applied in commit 65816c1034769e714edb70f59a33bc5472d9e55f ("arm64: dts: ls1028a-qds: move rtc node to the correct i2c bus") Compile-tested: lantiq/xrx200, bcm27xx/bcm2710 Run-tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.163Hauke Mehrtens2021-12-121-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: target/linux/mvebu/patches-5.4/001-PCI-aardvark-Wait-for-endpoint-to-be-ready-before-tr.patch target/linux/mvebu/patches-5.4/016-PCI-aardvark-Train-link-immediately-after-enabling-t.patch target/linux/mvebu/patches-5.4/017-PCI-aardvark-Improve-link-training.patch target/linux/mvebu/patches-5.4/018-PCI-aardvark-Issue-PERST-via-GPIO.patch target/linux/mvebu/patches-5.4/020-arm64-dts-marvell-armada-37xx-Set-pcie_reset_pin-to-.patch The following patch does not apply to upstream any more and needs some more work to make it work fully again. I am not sure if we are still able to set the UART to a none standard baud rate. target/linux/ath79/patches-5.4/921-serial-core-add-support-for-boot-console-with-arbitr.patch These patches needed manually changes: target/linux/generic/pending-5.4/110-ehci_hcd_ignore_oc.patch target/linux/ipq806x/patches-5.4/0065-arm-override-compiler-flags.patch target/linux/layerscape/patches-5.4/804-crypto-0016-MLKU-114-1-crypto-caam-reduce-page-0-regs-access-to-.patch target/linux/mvebu/patches-5.4/019-PCI-aardvark-Add-PHY-support.patch target/linux/octeontx/patches-5.4/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch All others updated automatically. Compile-tested on: malta/le, armvirt/64, lantiq/xrx200 Runtime-tested on: malta/le, armvirt/64, lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.150Hauke Mehrtens2021-10-025-34/+34
| | | | | | | | | | | | | | | | | | Manually rebased: generic/backport-5.4/370-netfilter-nf_flow_table-fix-offloaded-connection-tim.patch generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch Removed upstreamed: generic/backport-5.4/040-ARM-8918-2-only-build-return_address-if-needed.patch layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.142David Bauer2021-08-245-44/+44
| | | | | | | Compile-tested: ath79-generic ipq40xx-generic Run-tested: ipq40xx-generic Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.132Hauke Mehrtens2021-07-192-2/+2
| | | | | | | | | | | | Manually rebased layerscape/patches-5.4/805-display-0002-drm-rockchip-prepare-common-code-for-cdns-and-rk-dpi.patch All others updated automatically. Compile-tested on: ramips/mt7621 Runtime-tested on: ramips/mt7621 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: add missing config symbolsDavid Bauer2021-07-131-0/+3
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.128Hauke Mehrtens2021-06-271-1/+1
| | | | | | | | | | | | | | | Manually rebased bcm27xx/patches-5.4/950-0089-cgroup-Disable-cgroup-memory-by-default.patch Replaced with patch from Raspberry Pi kernel 5.10 patches mvebu/patches-5.4/002-PCI-aardvark-Don-t-rely-on-jiffies-while-holding-spi.patch Applied upstream All others updated automatically. Compile-tested on: ath79/generic, lantiq/xrx200, brcm27xx Runtime-tested on: ath79/generic, lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.124Hauke Mehrtens2021-06-065-35/+35
| | | | | | | | | | | | | Manually rebased generic/hack-5.4/662-remove_pfifo_fast.patch ramips/patches-5.4/0048-asoc-add-mt7620-support.patch All others updated automatically. Compile-tested on: armvirt/64, x86/generic, ath79/generic, ramips/mt7621 Runtime-tested on: armvirt/64, x86/generic, ath79/generic Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.114Hauke Mehrtens2021-05-021-1/+1
| | | | | | | | | | | | | | | | | | | | | | | Removed because in upstream* mvebu/patches-5.4/319-ARM-dts-turris-omnia-configure-LED-2--INTn-pin-as-interrupt-pin.patch Manually rebased* generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch Added new backport* generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch All others updated automatically. The new backport was included based on this[1] upstream commit that will be mainlined soon. This change is needed because Eric Dumazet's check for NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use napi_gro_frags(). Compile-tested on: x86/64, armvirt/64, ath79/generic Runtime-tested on: x86/64, armvirt/64, ath79/generic Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.111Hauke Mehrtens2021-04-114-42/+42
| | | | | | | | | | | | | | | | | | | | | Refreshed all patches. The following patches were manually changed: * 610-netfilter_match_bypass_default_checks.patch * 611-netfilter_match_bypass_default_table.patch * 802-can-0002-can-rx-offload-fix-long-lines.patch * 802-can-0003-can-rx-offload-can_rx_offload_compare-fix-typo.patch * 802-can-0004-can-rx-offload-can_rx_offload_irq_offload_timestamp-.patch * 802-can-0005-can-rx-offload-can_rx_offload_reset-remove-no-op-fun.patch * 802-can-0006-can-rx-offload-Prepare-for-CAN-FD-support.patch * 802-can-0018-can-flexcan-use-struct-canfd_frame-for-CAN-classic-f.patch The can-dev.ko model was moved in the upstream kernel. Compile-tested on: x86/64, armvirt/64, ath79/generic Runtime-tested on: x86/64, armvirt/64, ath79/generic Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2021-04-113-5/+0
| | | | | | | Move some disabled symbols found in armvirt target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> (cherry picked from commit 12e942b1fdda874542e0a4e6ea892969fedab975)
* kernel: bump 5.4 to 5.4.108Hauke Mehrtens2021-03-271-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: x86_64, ath79, lantiq Runtime-tested on: x86_64, ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.4 to 5.4.102Hauke Mehrtens2021-03-066-11/+11
| | | | | | | | | Refreshed all patches. Compile-tested on: ath79, lantiq, ipq40xx, x86_64 Runtime-tested on: ipq40xx, x86_64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-186-2/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c13c186646aff2badb51a43b248825d0fe5a0)
* mediatek: add Ubiquiti LED driverDavid Bauer2021-02-185-0/+242
| | | | | | | | | | | | Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED controller based on the Holtek HT32F52241 MCU. This driver is initially used by the Ubiquiti UniFi 6 LR, however judging from FCC pictures the MCU is also found on the U6-Mesh as well as the U6-Extender. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit c9137e2ddf97ede1db399dc38acff26feb48ba7e)
* target: use SPDX license identifiers on scriptsAdrian Schmutzler2021-02-102-7/+2
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-101-4/+2
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.96John Audia2021-02-081-1/+1
| | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Run-tested [*]: ramips/mt7621 (R6800, DIR-878 A1, EAP235-Wall) Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* treewide: drop shebang from non-executable lib filesAdrian Schmutzler2021-01-291-2/+0
| | | | | | | | | | | | This drops the shebang from another bunch of files in various /lib folders, as these are sourced and the shebang is useless. Fix execute bit in one case, too. This should cover almost all trivial cases now, i.e. where /lib is actually used for library files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: remove generic profilesAdrian Schmutzler2021-01-273-45/+0
| | | | | | | | | | We have support for reference boards available on this target, so support for an additional generic profile does not make much sense. Remove it to have one thing less to maintain. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 5.4 to 5.4.92John Audia2021-01-261-1/+1
| | | | | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64. Run-tested [*]: ath79/generic, octeon, ramips/mt7621, realtek. No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* config: limit CONFIG_PERF_EVENTS to top-level generic configsTony Ambardar2021-01-252-2/+0
| | | | | | Remove redundant target-level settings. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.90John Audia2021-01-192-2/+2
| | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
* kernel: bump 5.4 to 5.4.89John Audia2021-01-153-5/+5
| | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
* mediatek: remove unnecessary execute permission bitSungbo Eo2021-01-031-0/+0
| | | | | | | | | Kernel config does not need to be executable. 644 is enough. Fixes: 25d9df670b85 ("mediatek: add v5.4 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [split by targets] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.86Adrian Schmutzler2021-01-013-6/+6
| | | | | | | | | | | | | | | | | Removed upstreamed patches: pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch Manually merged: pending-5.4/611-netfilter_match_bypass_default_table.patch layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64 Run-tested: ipq806x/R7800, realtek Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-223-7/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: bump 5.4 to 5.4.85John Audia2020-12-221-1/+1
| | | | | | | | | | | | | All modifications made by update_kernel.sh run in a fresh clone without any existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: improve skb hash on the mtk ethernet driverFelix Fietkau2020-12-181-2/+2
| | | | | | | | The PPE only provides a 14 bit hash, however many uses of the skb hash expect the hash to use the full 32 bit range. Use jhash to extend the hash to the full size Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.82John Audia2020-12-091-1/+1
| | | | | | | | | | | | | | | | Removed since included upstream and could be reverse-applied by quilt: backport-5.4/315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch Remaining modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [build/run x86_64]
* kernel: bump 5.4 to 5.4.80John Audia2020-11-261-1/+1
| | | | | | | | | | | | | | | | | Removed since could be reverse-applied by quilt and found to be included upstream: backport-5.4/789-net-usb-qmi_wwan-Set-DTR-quirk-for-MR400.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/generic Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64 build/run]
* kernel: bump 5.4 to 5.4.77John Audia2020-11-187-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | Manually rebased patches: bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch generic-backport/744-v5.5-net-sfp-soft-status-and-control-support.patch layerscape/patches-5.4/819-uart-0005-tty-serial-fsl_lpuart-enable-dma-mode-for-imx8qxp.patch mvebu/patches-5.4/521-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch Removed: layerscape/patches-5.4/819-uart-0012-tty-serial-lpuart-add-LS1028A-support.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, lantiq/Easybox 904 xDSL, x86_64 Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL, x86_64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix mixed indent in DTS filesAdrian Schmutzler2020-11-165-141/+143
| | | | | | | | | mediatek frequently had mixed indent (tabs vs. spaces) in DTS files and DTS file kernel patches (probably due to careless copy/paste). The harmonizes these cases to tabs-only, as usual for DTS(I). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove default-state off for LEDsAdrian Schmutzler2020-11-164-11/+2
| | | | | | | | | default-state = "off" is default for LEDs, no need to specify it explicitly. https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-19 15:53:40 +0000