aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-186-2/+378
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c13c186646aff2badb51a43b248825d0fe5a0)
* mediatek: add Ubiquiti LED driverDavid Bauer2021-02-185-0/+242
| | | | | | | | | | | | Add a driver for controlling the RGB LED via Ubiquitis own "LEDBAR" LED controller based on the Holtek HT32F52241 MCU. This driver is initially used by the Ubiquiti UniFi 6 LR, however judging from FCC pictures the MCU is also found on the U6-Mesh as well as the U6-Extender. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit c9137e2ddf97ede1db399dc38acff26feb48ba7e)
* target: use SPDX license identifiers on scriptsAdrian Schmutzler2021-02-102-7/+2
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: use SPDX license identifiers on MakefilesAdrian Schmutzler2021-02-101-4/+2
| | | | | | Use SPDX license tags to allow machines to check licenses. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.96John Audia2021-02-081-1/+1
| | | | | | | | | | | | Ran update_kernel.sh in a fresh clone without any existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Run-tested [*]: ramips/mt7621 (R6800, DIR-878 A1, EAP235-Wall) Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* treewide: drop shebang from non-executable lib filesAdrian Schmutzler2021-01-291-2/+0
| | | | | | | | | | | | This drops the shebang from another bunch of files in various /lib folders, as these are sourced and the shebang is useless. Fix execute bit in one case, too. This should cover almost all trivial cases now, i.e. where /lib is actually used for library files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: remove generic profilesAdrian Schmutzler2021-01-273-45/+0
| | | | | | | | | | We have support for reference boards available on this target, so support for an additional generic profile does not make much sense. Remove it to have one thing less to maintain. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 5.4 to 5.4.92John Audia2021-01-261-1/+1
| | | | | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 Compile-tested [*]: ath79/{tiny,generic}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64. Run-tested [*]: ath79/generic, octeon, ramips/mt7621, realtek. No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* config: limit CONFIG_PERF_EVENTS to top-level generic configsTony Ambardar2021-01-252-2/+0
| | | | | | Remove redundant target-level settings. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.90John Audia2021-01-192-2/+2
| | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
* kernel: bump 5.4 to 5.4.89John Audia2021-01-153-5/+5
| | | | | | | | | | | | | | All modification made by update_kernel.sh in a fresh clone without existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86/64]
* mediatek: remove unnecessary execute permission bitSungbo Eo2021-01-031-0/+0
| | | | | | | | | Kernel config does not need to be executable. 644 is enough. Fixes: 25d9df670b85 ("mediatek: add v5.4 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [split by targets] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.86Adrian Schmutzler2021-01-013-6/+6
| | | | | | | | | | | | | | | | | Removed upstreamed patches: pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch Manually merged: pending-5.4/611-netfilter_match_bypass_default_table.patch layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64 Run-tested: ipq806x/R7800, realtek Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-223-7/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: bump 5.4 to 5.4.85John Audia2020-12-221-1/+1
| | | | | | | | | | | | | All modifications made by update_kernel.sh run in a fresh clone without any existing toolchains. Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: improve skb hash on the mtk ethernet driverFelix Fietkau2020-12-181-2/+2
| | | | | | | | The PPE only provides a 14 bit hash, however many uses of the skb hash expect the hash to use the full 32 bit range. Use jhash to extend the hash to the full size Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.82John Audia2020-12-091-1/+1
| | | | | | | | | | | | | | | | Removed since included upstream and could be reverse-applied by quilt: backport-5.4/315-v5.10-usbnet-ipeth-fix-connectivity-with-ios-14.patch Remaining modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [build/run x86_64]
* kernel: bump 5.4 to 5.4.80John Audia2020-11-261-1/+1
| | | | | | | | | | | | | | | | | Removed since could be reverse-applied by quilt and found to be included upstream: backport-5.4/789-net-usb-qmi_wwan-Set-DTR-quirk-for-MR400.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/generic Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64 build/run]
* kernel: bump 5.4 to 5.4.77John Audia2020-11-187-12/+12
| | | | | | | | | | | | | | | | | | | | | | | | Manually rebased patches: bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch generic-backport/744-v5.5-net-sfp-soft-status-and-control-support.patch layerscape/patches-5.4/819-uart-0005-tty-serial-fsl_lpuart-enable-dma-mode-for-imx8qxp.patch mvebu/patches-5.4/521-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch Removed: layerscape/patches-5.4/819-uart-0012-tty-serial-lpuart-add-LS1028A-support.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, lantiq/Easybox 904 xDSL, x86_64 Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL, x86_64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix mixed indent in DTS filesAdrian Schmutzler2020-11-165-141/+143
| | | | | | | | | mediatek frequently had mixed indent (tabs vs. spaces) in DTS files and DTS file kernel patches (probably due to careless copy/paste). The harmonizes these cases to tabs-only, as usual for DTS(I). Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove default-state off for LEDsAdrian Schmutzler2020-11-164-11/+2
| | | | | | | | | default-state = "off" is default for LEDs, no need to specify it explicitly. https://www.kernel.org/doc/Documentation/devicetree/bindings/leds/common.yaml Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.75John Audia2020-11-101-23/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased patches: bcm27xx: patches-5.4/950-0267-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch bcm53xx: patches-5.4/180-usb-xhci-add-support-for-performing-fake-doorbell.patch layerscape: patches-5.4/802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch patches-5.4/808-i2c-0002-MLK-10893-i2c-imx-add-irqf_no_suspend.patch patches-5.4/820-usb-0016-MLK-16735-usb-host-add-XHCI_CDNS_HOST-flag.patch Removed since could be reverse-applied by quilt: mediatek: patches-5.4/0700-arm-dts-mt7623-add-missing-pause-for-switchport.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86_64 Run-tested: ipq806x/R7800, x86_64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Curtis Deptuck <curtdept@me.com> [x86_64] Rebase of 802-can-0025-can-flexcan-add-LPSR-mode-support-for-i.MX7D.patch Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: Kevin Darbyshire-Bryant <kevin@darbyshire-bryant.me.uk>
* kernel: bump 5.4 to 5.4.73John Audia2020-11-011-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed patches: generic/pending-5.4 445-mtd-spinand-gigadevice-Only-one-dummy-byte-in-QUA.patch 446-mtd-spinand-gigadevice-Add-QE-Bit.patch pistachio/patches-5.4 150-pwm-img-Fix-null-pointer-access-in-probe.patch Manually rebased: layerscape/patches-5.4 801-audio-0011-Revert-ASoC-fsl_sai-add-of_match-data.patch 801-audio-0039-MLK-16224-6-ASoC-fsl_sai-fix-DSD-suspend-resume.patch 801-audio-0073-MLK-21957-3-ASoC-fsl_sai-add-bitcount-and-timestamp-.patch 820-usb-0009-usb-dwc3-Add-workaround-for-host-mode-VBUS-glitch-wh.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, mvebu (mamba, rango), x86_64, ramips/mt7621 Run-tested: ipq806x/R7800, mvebu (mamba, rango), x86_64, ramips (RT-AC57U) No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [alter 820-usb-0009-usb-dwc3-Add-workaround-for-host-mode-VBUS-glitch-wh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: remove support for kernel 4.19Adrian Schmutzler2020-10-3046-32563/+0
| | | | | | | We use 5.4 on all targets by default, and 4.19 has never been released in a stable version. There is no reason to keep it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.72John Audia2020-10-201-5/+5
| | | | | | | | | | | | All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* mediatek: rewrite flow offload codeFelix Fietkau2020-10-163-1244/+12
| | | | | | | | | The code is now much cleaner and works better than the old code. Preparation for submitting it upstream (though with a different API) Also add back MT7621 support and fix flow table coherence issues on MT7622 Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.71John Audia2020-10-151-1/+1
| | | | | | | | | | | | | | | All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, lantiq/Easybox 904 xDSL Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add lantiq test reports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move CONFIG_F2FS_CHECK_FS to generic kernel configHauke Mehrtens2020-10-111-1/+0
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Move CONFIG_F2FS_FS_SECURITY to generic kernel configHauke Mehrtens2020-10-111-1/+0
| | | | | | | Move the CONFIG_F2FS_FS_SECURITY kernel configuration option to the generic kernel configuration. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Remove 2FS_FS_XATTR and F2FS_STAT_FS symbols from target configsHauke Mehrtens2020-10-112-3/+0
| | | | | | | This config option was moved to the generic kernel configuration. Fixes: ab1bd576562b ("kernel: move F2FS_FS_XATTR and F2FS_STAT_FS symbols to generic") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: clean up XATTR config symbolsPaul Spooren2020-10-091-1/+0
| | | | | | | | | | | | | Extended attributes are required for overlayfs and have hence been long ago enabled for jffs2, but should be enabled unconditionally for all other filesystems which may potentially serve as overlayfs' upper directory. Previously it was inconsistently added in multiple targets. Add symbols to generic kernel config and remove all *_XATTR symbols from target configs. Signed-off-by: Paul Spooren <mail@aparcar.org> [keep things as they are for squashfs, improve commit message] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* kernel: bump 5.4 to 5.4.69John Audia2020-10-022-2/+2
| | | | | | | | | | | | | | | | | | | | | | Seemingly unneeded based on new upstream code so manually deleted: layerscape: 820-usb-0007-usb-dwc3-gadget-increase-timeout-value-for-send-ep-c.patch Manually merged: generic-hack: 251-sound_kconfig.patch All other modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711 Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add lantiq test report, minor commit message clarification] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.67John Audia2020-09-242-6/+2
| | | | | | | | | | | | | | All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x, lantiq/xrx200 and ath79/generic Run-tested: ipq806x (R7800), lantiq (Easybox 904 xDSL) No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add test on lantiq] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* target: update SPDX license namesAdrian Schmutzler2020-09-2239-39/+39
| | | | | | | SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to GPL-2.0-or-later. Reflect that in the SPDX license headers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: mt7622: select bluetooth module instead of firmwareChuanhong Guo2020-09-221-1/+1
| | | | Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: build btmtkuart as a kernel moduleChuanhong Guo2020-09-222-15/+12
| | | | | | | | bluetooth on mt7622 needs a firmware to start. It can't be built-in or it tries to load firmware before rootfs is mounted, and then fails. build it as a kernel module to fix that. Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* mediatek: mt7623: use bash for generating bootable imagesDavid Woodhouse2020-09-191-1/+1
| | | | | | | | | | | | | | | | | It turns out that 'echo -e' isn't portable; it doesn't work in the dash builtin echo and Ubuntu users are complaining. I can't even get octal (specified by POSIX) to work consistently because those variants of 'echo' which *do* support -e don't seem to interpret octalwithout it. I could switch to /bin/echo but using -e with that isn't actually portable *either* even though it works today. For now just stick with bash, and use its builtin. We may end up using something else entirely; perhaps perl. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* mediatek: fix missing pause on switch port for Banana Pi R2David Woodhouse2020-09-191-0/+27
| | | | | | This causes rx drops when running iperf. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* kernel: bump 5.4 to 5.4.66John Audia2020-09-191-1/+1
| | | | | | | | | | | | All modifications made by update_kernel.sh/no manual intervention needed Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64 No dmesg regressions, everything appears functional Signed-off-by: John Audia <graysky@archlinux.us> [add run test from PR] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: fix hardware flow offloadFelix Fietkau2020-09-171-1/+17
| | | | | | Add support for dealing with DSA ports Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ramips/mediatek: improve GRO performance, fix PPE packet parsingFelix Fietkau2020-09-133-108/+16
| | | | | | | | Backport upstream changes to initialize GDM settings and reset PPE Allow GMAC to recognize the special tag to fix PPE packet parsing Improve GRO performance by passing PPE L4 hash as skb hash Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.64John Audia2020-09-127-18/+18
| | | | | | | | | | | | | | | | | | | | | | Remove upstreamed patches: generic-backport 701-v5.5-net-core-use-listified-Rx-for-GRO_NORMAL-in-napi_gro.patch Manually merged: mediatek/patches-5.4 0603-net-dsa-mt7530-Extend-device-data-ready-for-adding-a.patch All other modifications made by update_kernel.sh Build-tested: ipq806x, lantiq/xrx200, mvebu, x86/64 Run-tested: ipq806x (R7800), mvebu (mamba, rango), lantiq/xrx200 (Easybox 904 xDSL), x86/64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add community build/run tests to commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek/ramips: remove an ethernet optimization patch that was reported to ↵Felix Fietkau2020-09-093-13/+13
| | | | | | | | cause a regression In some tests, crashes were observed Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: backport the latest version of the mt7531 support patchesFelix Fietkau2020-09-0911-1952/+2573
| | | | | | Fixes unknown unicast flooding issue Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: bump 5.4 to 5.4.63John Audia2020-09-063-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | Manually merged: hack-5.4 230-openwrt_lzma_options.patch bcm27xx 950-0283-hid-usb-Add-device-quirks-for-Freeway-Airmouse-T3-an.patch x86 011-tune_lzma_options.patch Remove upstreamed patches in collaboration with Ansuel Smith: ipq806x 093-1-v5.8-ipq806x-PCI-qcom-Add-missing-ipq806x-clocks-in-PCIe-driver.patch 093-2-v5.8-ipq806x-PCI-qcom-Change-duplicate-PCI-reset-to-phy-reset.patch 093-3-v5.8-ipq806x-PCI-qcom-Add-missing-reset-for-ipq806x.patch All other modifications made by update_kernel.sh Build-tested: bcm27xx/bcm2708, ipq806x, x86/64 Run-tested: ipq806x (R7800), x86/64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [update commit message/tested] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek/mt7622: adjust kernel cpu features to match the hardwareFelix Fietkau2020-09-061-15/+15
| | | | | | | Disable unnecessary errata/features Enable potentially needed ones Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: enable coherent DMA for ethernet and PCIFelix Fietkau2020-09-042-0/+191
| | | | | | Improves performance by eliminating the need for extra cache flushes Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: fix an irq handling issueFelix Fietkau2020-09-041-0/+24
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek/ramips: add patch to avoid unnecessary rearming of interruptsFelix Fietkau2020-09-042-10/+10
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 09:29:39 +0000