aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/mediatek/mt7622/base-files/etc/board.d/02_network
Commit message (Collapse)AuthorAgeFilesLines
* mediatek: Add support for Xiaomi Redmi Router AX6SRichard Huynh2022-03-211-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Also known as the "Xiaomi Router AX3200" in western markets, but only the AX6S is widely installation-capable at this time. SoC: MediaTek MT7622B RAM: DDR3 256 MiB (ESMT M15T2G16128A) Flash: SPI-NAND 128 MiB (ESMT F50L1G41LB or Gigadevice GD5F1GQ5xExxG) WLAN: 2.4/5 GHz 4T4R 2.4 GHz: MediaTek MT7622B 5 GHz: MediaTek MT7915E Ethernet: 4x 10/100/1000 Mbps Switch: MediaTek MT7531B LEDs/Keys: 2/2 (Internet + System LED, Mesh button + Reset pin) UART: Marked J1 on board VCC RX GND TX, beginning from "1". 3.3v, 115200n8 Power: 12 VDC, 1.5 A Notes: U-Boot passes through the ethaddr from uboot-env partition, but also has been known to reset it to a generic mac address hardcoded in the bootloader. However, bdata is also populated with the ethernet mac addresses, but is also typically never written to. Thus this is used instead. Installation: 1. Flash stock Xiaomi "closed beta" image labelled 'miwifi_rb03_firmware_stable_1.2.7_closedbeta.bin'. (MD5: 5eedf1632ac97bb5a6bb072c08603ed7) 2. Calculate telnet password from serial number and login 3. Execute commands to prepare device nvram set ssh_en=1 nvram set uart_en=1 nvram set boot_wait=on nvram set flag_boot_success=1 nvram set flag_try_sys1_failed=0 nvram set flag_try_sys2_failed=0 nvram commit 4. Download and flash image On computer: python -m http.server On router: cd /tmp wget http://<IP>:8000/factory.bin mtd -r write factory.bin firmware Device should reboot at this point. Reverting to stock: Stock Xiaomi recovery tftp that accepts their signed images, with default ips of 192.168.31.1 + 192.168.31.100. Stock image should be renamed to tftp server ip in hex (Eg. C0A81F64.img) Triggered by holding reset pin on powerup. A simple implementation of this would be via dnsmasq's dhcp-boot option or using the vendor's (Windows only) recovery tool available on their website. Signed-off-by: Richard Huynh <voxlympha@gmail.com> (cherry picked from commit 9f9477b2751231d57cdd8c227149b88c93491d93)
* mediatek: add support for Ruijie RG-EW3200GX PROLanghua Ye2022-03-051-1/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | X32 Pro is another product name for it in the Chinese market. Specifications: - SoC: MT7622B - RAM: 256MB - Flash: XMC XM25QH128C or Winbond WQ25Q128JVSQ 16MB SPI NOR - Ethernet: 5x1GbE - Switch: MT7531BE - WiFi: 2.4G: MT7622 5G: MT7915AN+MT7975AN - 3LEDs: System LED(blue) + Mesh LED(green) + Mesh LED(red) - 2Keys: Mesh button + Reset button - UART: Marked J19 on board. 3.3v, 115200n1 - Power: 12V 2.5A MAC addresses as verified by OEM firmware: use address source WAN *:F4 ethaddr@product_info LAN *:F5 5g *:F6 2g *:F7 Flash instruction: 1. Serve the initramfs.img using a TFTP server with address 10.10.10.3. 2. Interrupt the uboot startup process via UART. 3. Select "System Load Linux to SDRAM via TFTP" item. 4. (important) Back up firmware(mtd7) partitions with: dd if=/dev/mtd7 of=/tmp/firmware.bin and then download the firmware.bin image via SCP. 5. Flash the OpenWrt sysupgrade firmware. Recovery stock firmware: 1. Transfer the firmware.bin image to the device. 2. Flash the image with: mtd write firmware.bin firmware Signed-off-by: Langhua Ye <y1248289414@outlook.com>
* mediatek: rework and fix mt7622-rfb1-ubi supportFelix Fietkau2022-01-131-1/+2
| | | | | | | | Limit bmt remapping range to cover everything up to and including the kernel image, use the rest of the flash area for ubi. Fix partition table and sysupgrade support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek/mt7622: unifi-6-lr: fix ucidef network configuration typoMark Mentovai2021-11-191-1/+1
| | | | | | | | There's no such thing as ucidef_set_interfaces_lan. It's ucidef_set_interface_lan. Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Mark Mentovai <mark@moxienet.com>
* mediatek: add alternative bootchain variant for UniFi 6 LRDaniel Golle2021-04-091-1/+2
| | | | | | | | Builds images for the Ubiquiti Network UniFi 6 LR device running the U-Boot build added by the previous commits. Everything but MTD partitions is moved to dtsi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add support for Buffalo WSR-2533DHP2INAGAKI Hiroshi2021-03-151-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Buffalo WSR-2533DHP2. The device uses the Broadcom TRX image format with a special magic. To be able to boot the images or load them they have to be wrapped with different headers depending how it is loaded. There are multiple ways to install OpenWrt on this device. Boot ramdisk from U-Boot ---------------------------- This will load the image and not write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux to SDRAM via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-initramfs-kernel.bin 4. The system boots the image Write to flash from U-Boot ----------------------------- This will load the image over tftp and directly write it into the flash. 1. Stop boot menu with "space" key 2. Select "System Load Linux Kernel then write to Flash via TFTP." 3. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory-uboot.bin 4. The system writes this image into the flash and boots into it. Write to flash from Web UI ----------------------------- This will load the image over over the Web UI and write it into the flash 1. Open the Web UI 2. Go to "管理" -> "ファームウェア更新" 3. Select "ローカルファイル指定" and click "更新実行" 4. Load this image: openwrt-mediatek-mt7622-buffalo_wsr-2533dhp2-squashfs-factory.bin 5. The system writes this image into the flash and boots into it. Specifications ------------------- * SoC: MT7622 (4x4 2.4 GHz Wifi) * Wifi: MT7615 (4x4 5 GHz Wifi) * Flash: Winbond W29N01HZ 128MB SLC NAND * RAM 256MB * Ethernet: Realtek RTL8367S (5 x 1GBit/s, SoC via 2.5GBit/s) Co-Developed-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-061-1/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* mediatek: rework support for BananaPi BPi-R64Daniel Golle2021-02-281-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | **What's new** * Bring support for the Bananapi BPi-R64 to the level desirable for a nice hackable routerboard. * Use ARM Trusted Firmware A from source. (goodbye binary preloader) * Use Das U-Boot from source. (see previous commit) * Assemble SD-card image using OpenWrt image-commands. (no gen_sd_cruz_foo.sh added, this is not Raspbian) * Updated kernel options to support root filesystem. * Updated DTS to match OpenWrt LAN ports, known LEDs, buttons, ... * Detect root device, handle sysupgrade, config restore, ... * Wire up (known) LEDs and buttons in OpenWrt-fashion. * Build one set of images from SD-card and eMMC. * Hopefully provide a good example of how things can be done right from scratch. **Installation and images** * Have an empty SD-card at hand * Write stuff to the card, as root (card device is /dev/mmcblkX) - write header, gpt, bl2, atf, u-boot and recovery kernel: `cat *bpi-r64-boot-sdcard.img *bpi-r64-initramfs-recovery.fit > /dev/mmcblkX` - rescan partitions: `blockdev --rereadpt /dev/mmcblkX` - write main system to production partition: `cat *bpi-r64-squashfs-sysupgrade.fit > /dev/mmcblkXp5` * Installation to eMMC works using SD-card bootloader via TFTP When running OpenWrt of SD-card, issue this to trigger installation to eMMC: `fw_setenv bootcmd run emmc_init` Be prepared to serve the content of bin/targets/mediatek/mt7622 on TFTP server address 192.168.1.254. **What's missing** * The red LED is always on, probably a hardware bug. * AHCI (probably needs DTS changes) * Ship SD-card image ready with every needed for eMMC install. * The eMMC has a second, currently unused boot partition. This would be ideal to store the WiFi EEPROM and Ethernet MAC address(es). @sinovoip ideas? Thanks to Thomas Hühn @thuehn for providing the hardware! Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add alternative UBI NAND layout for Linksys E8450Daniel Golle2021-02-281-17/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The vendor flash layout of the Linksys E8450 is problematic as it uses the SPI-NAND chip without any wear-leveling while at the same time wasting a lot of space for padding. Use an all-UBI layout instead, storing the kernel+dtb+squashfs in uImage.FIT standard format in UBI volume 'fit', the read-write overlay in UBI volume 'rootfs_data' as well as reduntant U-Boot environments 'ubootenv' and 'ubootenv2', and a 'recovery' kernel+dtb+initramfs uImage.FIT for dual-boot. ** WARNING ** THIS PROCEDURE CAN EASILY BRICK YOUR DEVICE PERMANENTLY IF NOT CARRIED OUT VERY CAREFULLY AND EXACTLY AS DESCRIBED! Step 0 * Configure your PC to have the static IPv4 address 192.168.1.254/24 * Provide bin/targets/mediatek/mt7622 via TFTP Now continue EITHER with step 1A or 1B, depending on your preference (and on having serial console wired up or not). Step 1A (Using the vendor web interface (or non-UBI OpenWrt install)) In order to update to the new bootloader and UBI-based firmware, use the web browser of your choice to open the routers web-interface accessible on http://192.168.1.1 * Navigate to 'Configuration' -> 'Administration' -> 'Firmware Upgrade' * Upload the file openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and proceed with the upgrade. * Once OpenWrt comes up, use SCP to upload the new bootloader files to /tmp on the router: *-mt7622-linksys_e8450-ubi-preloader.bin *-mt7622-linksys_e8450-ubi-bl31-uboot.fip * Connect via SSH as you will now need to replace the bootloader in the Flash. ssh root@192.168.1.1 (the usual warnings) * First of all, backup all the flash now: for mtd in /dev/mtdblock*; do dd if=$mtd of=/tmp/$(basename $mtd); done * Then use SCP to copy /tmp/mtdblock* from the router and keep them safe. You will need them should you ever want to return to the factory firmware! * Now flow the uploaded files: mtd -e /dev/mtd0 write /tmp/*linksys_e8450-ubi-preloader.bin /dev/mtd0 mtd -e /dev/mtd1 write /tmp/*linksys_e8450-ubi-bl31-uboot.fip /dev/mtd1 If and only if both writes look like the completed successfully reboot the router. Now continue with step 2. Step 1B (Using the vendor bootloader serial console) * Use the serial to backup all /dev/mtd* devices before using the stock firmware (you got root shell when connected to serial). * Then reboot and select 'U-Boot Console' in the boot menu. * Copy the following lines, one by one: tftpboot 0x40080000 openwrt-mediatek-mt7622-linksys_e8450-ubi-preloader.bin tftpboot 0x40100000 openwrt-mediatek-mt7622-linksys_e8450-ubi-bl31-uboot.fip nand erase 0x0 0x180000 nand write 0x40080000 0x0 0x180000 reset Now continue with step 2 Step 2 Once the new bootchain comes up, the loader will initialize UBI and the ubootenv volumes. It will then of course fail to find any bootable volume and hence resort to load kernel via TFTP from server 192.168.1.254 while giving itself the address 192.168.1.1 The requested file is called openwrt-mediatek-mt7622-linksys_e8450-ubi-initramfs-recovery.itb and your TFTP server should provide exactly that :) It will be written to UBI as recovery image and booted. You can then continue and flash the production OS image, either by using sysupgrade in the booted initramfs recovery OS, or by using the bootloader menu and TFTP. That's it. Go ahead and mess around with a bootchain built almost completely from source (only DRAM calibration blobs are fitted in bl2, and the irreplacable on-chip ROM loader remains, of course). And enjoy U-Boot built with many great features out-of-the-box. You can access the bootloader environment from within OpenWrt using the 'fw_printenv' and 'fw_setenv' commands. Don't be afraid, once you got the new bootchain installed the device should be fairly unbrickable (holding reset button before and during power-on resets things and allows reflashing recovery image via TFTP) Special thanks to @dvn0 (Devan Carpenter) for providing amazingly fast infra for test-builds, allowing for `make clean ; make -j$(nproc)` in less than two minutes :) Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* mediatek: add Linksys E8450 supportJohn Crispin2021-02-281-3/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys E8450, also known as Belkin RT3200, is a dual-band IEEE 802.11bgn/ac/ax router based on MediaTek MT7622BV and MediaTek MT7915AN chips. FCC: K7S-03571 and K7S-03572 Hardware highlights: - CPU: MediaTek MT7622BV (2x ARM Cortex-A53 @ 1350 MHz max.) - RAM: 512MB DDR3 - Flash: 128MB SPI-NAND (2k+64) - Ethernet: MT7531BE switch with 5 1000Base-T ports CPU port connected with 2500Base-X - WiFi 2.4 GHz: 802.11bgn 4T4R built-in antennas MT7622VB built-in - WiFi 5 GHz: 802.11ac/ax 4T4R built-in antennas MT7915AN chip on-board via PCIe MT7975AN front-end - Buttons: Reset and WPS - LEDS: 3 user controllable LEDs, 4 wired to switch - USB: USB2.0, single port - no Bluetooth (supported by SoC, not wired on board) - Serial: JST PH 2.0MM 6 Pin connector inside device ----_____________---- [ GND RX - TX - - ] --------------------- - JTAG: unpopulated ARM JTAG 20-pin connector (works) This commit adds support for the device in a way that is compatible with the vendor firmware's bootloader and dual-boot flash layout, the resulting image can directly be flashed using the vendor firmware. Signed-off-by: Daniel Golle <daniel@makrotopia.org> Signed-off-by: John Crispin <john@phrozen.org> Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add support for Ubiquiti UniFi 6 LRDavid Bauer2021-02-181-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- MediaTek MT7622 512MB DDR3 RAM 64M SPI-NOR Flash (Winbond W25Q512JV) MediaTek MT7622 802.11bgn 4T4R WMAC MediaTek MT7915 802.11ax 4T4R Marvell AQR1112 100/1000/2500 NBase-T PHY Holtek HT32F52241 LED controller Reset Switch UART ---- CPU UART0 at the pinout next to the Holtek MCU. Pinout (first pin next to SoC / MCU) 0 3V3 1 RX 2 TX 3 GND Settings are 115200 8N1. Opening the case ---------------- Opening the case is not a nice task, as itis glued together. Insert a flat knife between the front and back casing below the ethernet port. Open up a gap this way and insert a flat scredriver, remove the knife. Work your way around the casing by applying force to seperate the front and back casing. This losens the glue and opens the plastic clips. Be gentle, as these clips are very cheap and break quickly. Installation ------------ 1. Connect to the booted device at 192.168.1.20 using username/password "ubnt". 2. Transfer the OpenWrt sysupgrade image to the device using SCP. 3. Check the mtd partition number for bs / kernel0 / kernel1 $ cat /proc/mtd 4. Set the bootselect flag to boot from kernel0 $ dd if=/dev/zero bs=1 count=1 of=/dev/mtdblock6 5. Write the OpenWrt sysupgrade image to both kernel0 as well as kernel1 $ dd if=openwrt.bin of=/dev/mtdblock8 $ dd if=openwrt.bin of=/dev/mtdblock9 6. Reboot the device. It should boot into OpenWrt. Signed-off-by: David Bauer <mail@david-bauer.net>
* mediatek: fix mt7622-rfb1 board supportFelix Fietkau2020-08-061-0/+3
| | | | | | | Make GPIO keys active-low. Add DSA support Signed-off-by: Felix Fietkau <nbd@nbd.name>
* mediatek: add mt7531 DSA supportJohn Crispin2020-06-071-0/+4
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: add bpi-r64 emmc supportJohn Crispin2020-06-071-1/+1
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* mediatke: add support for elecom-wrc-2533gentJohn Crispin2020-03-271-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MT7622-based Elecom WRC-2533gent router, with spi-nand storage and 512MB RAM. The device has the following specifications: * MT7622 (arm64 dual-core) * 512MB RAM (DDR3) * 4GB storage (spi-nand) * 5x 1Gbps Ethernet (RTL8337C switch) * 1x UART header * 1x USB 3.0 port * 5x LEDs * 1x reset button * 1x WPS button * 1x slider switch * 1x DC jack for main power (12V) The following has been tested and is working: * Ethernet switch * 2.4g and 5g wifi * USB 3.0 port * sysupgrade * buttons/leds Not working: * bluetooth firmware does not load even though it is present int he rootfs Signed-off-by: John Crispin <john@phrozen.org>
* mediatek: split base-files into subtargetsAdrian Schmutzler2020-01-141-0/+29
This splits some base-files across subtargets, as done previously on ath79 and ramips and also introduced for mt7629 subtarget here already. Most of the existing base-files content is specific to mt7623. While at it, apply the following fixes: - Remove lots of trailing whitespaces - Remove wildcard on unielec,u7623-02-emmc-512m - Remove inconsistent quotation marks in cases Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: John Crispin <john@phrozen.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-26 02:30:36 +0000