aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V)John Crispin2015-07-075-1/+185
| | | | | | | | lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V) Signed-off-by: Jannis Pinter <jannis@pinterjann.is> SVN-Revision: 46224
* lantiq: Add support for the BT Home Hub 5AJohn Crispin2015-07-077-2/+360
| | | | | | | | | | | | | | | u-boot support depends on the next "upstream" version ([0]) from Daniel Schwierzeck. Since the installation process is quite complicated a "how to" was added to the wiki: [1] [0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next [1] http://wiki.openwrt.org/toh/bt/homehub_v5a V2: Use the correct PCI interrupt (fixes 2.4GHz wifi) Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46223
* lantiq: Silence the printk when a PCIe error interrupt arrivesJohn Crispin2015-07-071-1/+1
| | | | | | | | | | Basically the only error I am seeing is "Correctable Error". Also newer lantiq PCIe drivers have this message wrapped in a "if debug enabled" block. So it should be safe to disable this warning. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46222
* lantiq: Make the MEI address available for kernel driversJohn Crispin2015-07-071-0/+1
| | | | | | | | Newer DSL driver versions depend on the address information. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46221
* lantiq: Change the data-type of mac address in ETOP driverJohn Crispin2015-07-072-10/+1
| | | | | | | | Make it consistent with the net_device struct and the xrx200 driver Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46219
* lantiq: Add support for linux 4.1John Crispin2015-07-0739-0/+19662
| | | | | | | | | | | | | | | | All (still relevant) patches were refresh. The following patches were dropped because they are applied upstream: - 0003-MIPS-lantiq-handle-vmmc-memory-reservation.patch - 0005-MIPS-lantiq-add-reset-controller-api-support.patch - 0006-MIPS-lantiq-reboot-gphy-on-restart.patch - 0009-MIPS-lantiq-command-line-work-around.patch - 0010-MIPS-lantiq-export-soc-type.patch - 0011-lantiq-add-support-for-xrx200-firmware-depending-on-.patch - 0037-MIPS-lantiq-move-eiu-init-after-irq_domain-register.patch Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 46216
* kernel: update 3.18 to 3.18.17Jonas Gorski2015-06-301-1/+1
| | | | | | | | | Changelog: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.17 Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46150
* kernel: update 3.18 to 3.18.16Jonas Gorski2015-06-174-10/+8
| | | | | | | | | | | Changelogs: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.15 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.16 Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46011
* lantiq: Backport gpio-stp-xway to fix the highest bits of the PHY LEDsJohn Crispin2015-06-051-0/+25
| | | | | | This fixes the LAN2 LED on Arcadyan VGV7510KW22. SVN-Revision: 45899
* lantiq: Add support for Arcadyan VGV7510KW22 (known as o2 Box 6431)John Crispin2015-06-058-0/+388
| | | | SVN-Revision: 45897
* lantiq: Make the CRC32 poly value configurable per deviceJohn Crispin2015-06-031-5/+5
| | | | | | | | | This also adds the old hardcoded value to the VGV7519BRN profile to make sure that images are still generated correctly. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 45882
* lantiq: fix VG3503J rootfs offsetJonas Gorski2015-06-011-1/+1
| | | | | | | | | | In r44391 the kernel partion size was increased to allow larger kernels, but the rootfs partition offset was missed. Fix this by setting the rootfs offset to the expected value. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45868
* lantiq: fix imagebuilderJohn Crispin2015-05-301-4/+14
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45851
* lantiq: Fix initialization of the PCI IRQs when PCIe is also enabledJohn Crispin2015-05-231-18/+19
| | | | | | | | | | There are already ifx_pcie_bios_{map_irq,plat_dev_init} hooks defined in ifxmips_pcie.c. Instead of defining a new hook we simply re-use the existing ones (this is basically what the lantiq BSP code does). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 45718
* lantiq: Fix PCIe bus when PCI is also enabled.John Crispin2015-05-231-10/+10
| | | | | | | | | | | The PCIe bus seems to require a hack/workaround when PCI is enabled as well. Unfortunately this is guarded by an CONFIG_IFX_PCI ifdef, which is only defined in lantiq's BSP code. The config symbol for the upstream lantiq PCI driver is CONFIG_PCI_LANTIQ. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 45717
* kernel: update 3.18 to 3.18.14Jonas Gorski2015-05-213-7/+7
| | | | | | | | | | | | | | Changelogs: * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.12 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.13 * https://www.kernel.org/pub/linux/kernel/v3.x/ChangeLog-3.18.14 Build tested on brcm63xx and ipq806x, runtested on brcm63xx. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 45711
* The ability to read MAC addresses from MTD is useful for other targets ↵Imre Kaloz2015-05-031-76/+0
| | | | | | | | besides ramips and lantiq as well. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net> SVN-Revision: 45596
* lantiq: remove arphaned folderJohn Crispin2015-03-273-56/+0
| | | | | | | | the new buildbot was picking this up as a valid target. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 45068
* lantiq/xrx200: cleanup default packagesJohn Crispin2015-03-176-52/+21
| | | | | | | Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44867
* lantiq: make xrx200 targets use the upstream dwc2 driverJohn Crispin2015-03-175-9/+9
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44857
* lantiq: drop 3.14 supportJohn Crispin2015-03-1647-17512/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44812
* lantiq: add a better fix to strip FCS from ethernet packets on XRX200Felix Fietkau2015-03-151-0/+25
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44771
* lantiq: enable atm-esi by default for xrx200Felix Fietkau2015-03-151-1/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 44769
* kenrel: refresh patchesJohn Crispin2015-03-119-268/+268
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44678
* lantiq: make the new dwc2 support only work for vr9John Crispin2015-03-111-4/+5
| | | | | | | | danube needs to be added Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44677
* lantiq: Convert Zyxel P-2812HNU-FX and TP-Link TD-W8970 to support dwc2John Crispin2015-03-113-1/+19
| | | | | | | | | | | | | | Here the device tree entry for ifxhcd is listed as compatible with one supported in dwc2 (after patching the dwc driver appropriately). A second entry is added to support the second core of the hcd. This entry is listed to be compatible with only dwc2. Done this way there should be backwards support for both hcd drivers (ltq-hcd and dwc2) Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44676
* lantiq: Use platform endianness when accessing dwc2 registersJohn Crispin2015-03-111-0/+3184
| | | | | | | | | | | | | | | | | | | | This patch switches calls to readl/writel to their dwc2_readl/dwc2_writel equivalents which preserve platform endianness. This patch is necessary to access dwc2 registers correctly on big endian systems such as the mips based SoCs made by Lantiq. Then dwc2 can be used to replace ifx-hcd driver for Lantiq platforms found e.g. in OpenWrt. The patch was autogenerated with the following commands: $EDITOR core.h sed -i "s/\<readl\>/dwc2_readl/g" *.c hcd.h hw.h sed -i "s/\<writel\>/dwc2_writel/g" *.c hcd.h hw.h Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44675
* lantiq: Add sensible hw-defaults for dwc2John Crispin2015-03-111-0/+45
| | | | | | | | | | | Lantiq driver does not work with autodetected fifo sizes so use ones from original ltq-hcd driver in dwc2. Other values can be autodetected. Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44674
* lantiq: Configure gpio power output pin when initializing dwc2 usbJohn Crispin2015-03-111-0/+35
| | | | | | | | | Port gpio code from original ltq-hcd driver to dwc2. Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44673
* lantiq: Add usb initialization bits from ltq-hcd to platform initJohn Crispin2015-03-111-0/+95
| | | | | | | | | | | | | | Add VR9 specific usb initialization bits from ltq-hcd to platform initialization. This patch is more of a proof-of-concept than production quality since the initialization registers are different on other lantiq platforms. Signed-off-by: Antti Seppälä <a.seppala@gmail.com> Signed-off-by: Vincent Pelletier <plr.vincent@gmail.com> SVN-Revision: 44672
* kernel: move KERNFS to generic configJohn Crispin2015-03-062-2/+0
| | | | | | | | KERNFS symbol is selected by SYSFS, so place it in generic config. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> SVN-Revision: 44615
* kernel: disable ARCH_NEEDS_CPU_IDLE_COUPLEDJohn Crispin2015-03-062-2/+0
| | | | | | | | | Disable ARCH_NEEDS_CPU_IDLE_COUPLED by-default in generic config, since only one platfrom (omap) needs them. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> SVN-Revision: 44614
* kernel: move MTD_SPLIT_SUPPORT to generic configJohn Crispin2015-03-062-2/+0
| | | | | | | | | | | CONFIG_MTD_SPLIT_SUPPORT symbol default value is 'y' and many platform specific configs explicitly enables it, while no one platform disables this symbol. So place it in generic config and remove from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> SVN-Revision: 44612
* kernel: remove GENERIC_NET_UTILS from platform configsJohn Crispin2015-03-062-2/+0
| | | | | | | | | | CONFIG_GENERIC_NET_UTILS is selected by CONFIG_NET and already enabled in generic config, so we don't need this symbol in platform specific configurations. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> SVN-Revision: 44611
* kernel: move CONFIG_MIPS_O32_FP64_SUPPORT to generic configsJonas Gorski2015-03-013-3/+0
| | | | | | | | | Most MIPS targets have it disabled, so move the symbol to the generic configs to keep target configs small. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 44583
* lantiq: disable buffered writes on Intel command set flashJohn Crispin2015-02-142-0/+22
| | | | | | | | | | | | Some Lantiq SoCs are not able to use buffered writes properly with Intel command set flash due to the way NOR addresses on EBU are manipulated. This patch disables buffered writes on those devices. The only device affected at the moment is ARV4510PW, others use AMD/Fujitsu command set. Signed-off-by: Matti Laakso <malaakso@elisanet.fi> SVN-Revision: 44451
* lantiq: Fix flash for targets with NO_XIPJohn Crispin2015-02-142-2/+2
| | | | | | | | | For targets with NO_XIP ltq_mtd->map[i].phys equals -1 and devm_ioremap fails. Fix this by using pdev->resource[i].start instead. Signed-off-by: Matti Laakso <malaakso@elisanet.fi> SVN-Revision: 44450
* lantiq: fix DGN3500 root deviceJohn Crispin2015-02-131-1/+1
| | | | | | Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44428
* lantiq: make m25p80 work againJohn Crispin2015-02-122-2/+12
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44421
* lantiq: fix mac addr assignment inside lantiq_etopJohn Crispin2015-02-121-6/+6
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44420
* lantiq: PCI should be enabled on vrx200John Crispin2015-02-121-1/+0
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44419
* lantiq: fix VG3503J partition table for newer kernelsJohn Crispin2015-02-112-3/+3
| | | | | | | | the kernel has increased and does not fit into the 1,5MB anymore. Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44391
* lantiq: td-w8970: fix failsafe modeJohn Crispin2015-02-091-0/+18
| | | | | | | | Fix failsafe mode for TD-W8970, register interface for preinit. Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44353
* lantiq: td-w8970: fix reset buttonJohn Crispin2015-02-091-2/+2
| | | | | | | | For TP-LINK TD-W8970 button should work as "reset", not "BTN_1". Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com> SVN-Revision: 44352
* lantiq: add 3.18 supportJohn Crispin2015-02-0949-349/+16771
| | | | | | Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 44348
* lantiq: fix patches after 3.14.32 bumpLuka Perkov2015-02-0810-65/+49
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 44320
* lantiq: correct value for fpi clock on ar9John Crispin2015-01-231-0/+21
| | | | | | | | | | | | | | | | | | | | | This adds a patch to target/linux/lantiq/patches-3.14 fixing a bug clock code on ar9. The current version returns the wrong value for the fpi clock frequency in some cases. See discussion for further details: https://lists.openwrt.org/pipermail/openwrt-devel/2015-January/030688.html I'm not sure about the patch naming and numbering convention. Do please let me know it this is not OK. Many thanks, Ben Mulvihill Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 44083
* lantiq: DGN3500 cleanupsJohn Crispin2015-01-182-3/+1
| | | | | | | | | This patch builds on the previous three to streamline support for the Netgear DGN3500. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44032
* lantiq: Restore call to orphaned etop functionJohn Crispin2015-01-181-16/+44
| | | | | | | | | It seems the call to ltq_get_eth_mac() disappeared at some point. This patch puts it where it currently most makes sense. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44031
* lantiq: Fix initscript issueJohn Crispin2015-01-181-1/+1
| | | | | | | | | Currently this initscript fails if the macaddr has any leading zeroes. This patch corrects the problem. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> SVN-Revision: 44029
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 18:39:02 +0000