aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: enable cpu temp driver for all vr9 boardsMathias Kresin2016-10-196-20/+4
| | | | | | | Only present on v1.2 vr9 SoCs but the driver takes care to not load on boards having a v1.1 SoC. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix thermal sensors driverMathias Kresin2016-10-191-5/+21
| | | | | | | | | | | | | | | | | | | | Read the temperature including the decimale place from the CGU_GPHY1_CR register. Decrement the temperature read from the register by 38.0 degree celsius. The temperature range of the sensor is -38.0 to +154 °C and the register value 0 is equal to -38.0 °C. This fixes the report of unrealistic temperatures as seen on all tested boards. Give the SoC a few milliseconds to get the first temperature value. On some rare occasions there is no temperature value in the register when read the first time after activation. This leads to a reported temperature of -38.0 °C on boot. Only version 1.2 of the vr9 SoC has a temperature sensor. Add a check to make sure the driver doesn't load on v1.1 vr9 SoCs. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: Sanitize device tree filesAndreas Eberlein2016-10-1956-656/+668
| | | | | | | | | | The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes. This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend. Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de> [sanitize all device tree files] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: Fix buttons for ARV752DPWAndreas Eberlein2016-10-191-5/+5
| | | | | | | | The GPIO for reset switch is wrong in definition. Further the key codes for the two additional buttons are ineffective. Both is fixed here. Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de>
* lantiq: use new build code for DGN3500Mathias Kresin2016-10-191-99/+36
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop lzma-loaderMathias Kresin2016-10-1924-2792/+0
| | | | | | It isn't used any more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: rework VG3503J imageMathias Kresin2016-10-193-79/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new image build code and remove the lzma loader. The lzma loader was used to cheat the signature validation of the bootloader and I found another way to do this. To migrate boards already using LEDE/OpenWrt to the new image the following steps need to be done once: VR9 # run reset_uboot_config VR9 # reset VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The mac address is printed on the label at the bottom of the case. The following steps are need to be done during first install: VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The image uses the uImage firmware splitter now instead of hardcoded kernel and rootfs partitions. The firmware partition size was extended to use flash space that was reserved for partitions required only by the ECI firmware. Due to the changes an upgrade to a later LEDE revision from a running LEDE is supported now. A default switch config was added and the device uses the same MAC addresses as the ECI firmware now instead of the same for all VG3503J. Signed-off-by: Mathias Kresin <dev@kresin.me>
* switch to the new usbport LED triggerRafał Miłecki2016-10-192-21/+21
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: use wpad-mini for WBMR boardsMathias Kresin2016-10-152-20/+2
| | | | | | | | | | The WBMR boards are the only ones in the whole tree selecting the wpad and hostapd-utils package by default. Remove the wps uci-default script as well, there is no obvious reason why the wps config need to be set only for this board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix ARV452CQW keysMathias Kresin2016-10-151-1/+1
| | | | | | Fix the typo in the gpio-keys-polled compatible string. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix lantiq-dsl output spamMathias Kresin2016-10-111-1/+1
| | | | | | | | | | | | | | | | | In case the adsl/vdsl service is disabled intentional, the output is cluttered with the following message multiple times if the status of the dsl line is queried: killall: vdsl_cpe_control: no process killed If the dsl line status is queried by LuCI, the logfile is spammed with the message. Fix the issue by using killall in quite mode. In quite mode killall still returns a non-zero value if the to be killed process can not be found so that existing logic based on the return value still works. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix BTHOMEHUBV2B default packagesMathias Kresin2016-10-061-1/+1
| | | | | | | | | | Due to the introduced double whitespace the default package selection isn't applied. This leads to errors like a not working networking because of a missing swconfig binary. Fixes FS#208. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fixup last commitsMathias Kresin2016-10-055-9/+9
| | | | | | | Revert the rename of unrelated device tree nodes. Rename the missed leds of the Speedport W 504V Typ A. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix usb leds/triggerMathias Kresin2016-10-054-8/+11
| | | | | | | | | | | Add USB led aliases to boards having an led which is meant to be used as USB led according to the manuals. Remove the kmod-ledtrig-usbdev from the default package selection for boards not having an USB led. Add the kmod-ledtrig-usbdev to boards where it is missing. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use aliases device tree node for ledsMathias Kresin2016-10-0536-285/+277
| | | | | | The chosen node is clearly the wrong place for aliases. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: cleanup led handling functionsMathias Kresin2016-10-053-19/+22
| | | | | | | | | Use a more generic name for the lantiq_get_dt_led_chosen function. Drop the lantiq_is_dt_led_chosen function. The lantiq_get_dt_led function can be used to achieve the same. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: apply alphabetical order to led fileMathias Kresin2016-10-051-12/+12
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* ntiq: make i2c-lantiqi driver compile againHauke Mehrtens2016-10-031-9/+9
| | | | | | | It missed some changes needed for kernel 4.4. This is only used by the Falcon SoC and not for the xRX SoCs. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: update to v4.4.23Álvaro Fernández Rojas2016-09-301-3/+3
| | | | | | | Refresh patches for all targets that support kernel 4.4. compile/run-tested on brcm2708/bcm2710 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* treewide: remove bad local shell variable declarationsJo-Philipp Wich2016-09-241-6/+1
| | | | | | | Local variable declarations outside of functions are illegal since the Busybox update to v1.25.0, therfore remove them from the appropriate places. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* lantiq: do not "local" variables outside of a functionMartin Blumenstingl2016-09-242-5/+5
| | | | | | | | | Older busybox versions allowed using the local keyword outside of functions, whereas 1.25.0 (which was introduced in 06fa1c46fc32) do not allow this anymore (leading to the following error when executing the script: "file: local: line nn: not in a function"). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* kernel: update kernel 4.4 to version 4.4.20Álvaro Fernández Rojas2016-09-151-1/+1
| | | | | | | Refresh patches for all targets that support kernel 4.4. Compile-tested on brcm2708 only. Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
* kernel: Backport pending appended DTB handling patchesDaniel Gimpelevich2016-09-121-0/+49
| | | | | | | | | | Backport patches from upstream Linux kernel which are making the kernel stores the appended dtb not in the same resisters as defined in the UHI specification, use a separate variable on MIPS. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us> [some modifications] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* cleanup ucidef_set_interface* usageMathias Kresin2016-09-101-2/+2
| | | | | | | | - quote the interface name - remove call of not existing function - remove the proto if it's the default proto Signed-off-by: Mathias Kresin <dev@kresin.me>
* use immediate set in target MakefilesMathias Kresin2016-09-101-1/+1
| | | | | | | | No functional change, it's just to have the same style everywhere. This way I don't need to use any regex magic to extract all subtargets for compile tests. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: apply alphabetical orderMathias Kresin2016-09-101-43/+43
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: cleanup default switch configMathias Kresin2016-09-101-32/+19
| | | | | | | | | | | | | | | | Add or fix the physical port number of switch ports to allow LuCI to display the ports in physical order. Remove the physical port number in case bridge port and physical port order are the same. Reorder the ucidef_add_switch parameter to be aligned with the switch port number. Remove board settings which are covered by the default case and remove comments. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: enable cpu temp driver for more tested boardsMathias Kresin2016-09-102-1/+9
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: use k as unit suffix for blocksizeMathias Kresin2016-09-041-2/+2
| | | | | | | Use k as unit suffix for kilobyte to have a the same unit regardless of the used filesystem. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix ath5k EEPROM loadingMathias Kresin2016-08-241-9/+27
| | | | | | | | | | With 12fe4b579801ea812b64fc7e689716cd39c895ec I switched the ath5k eeprom extraction to an alternate code path. Unfortunately this code seams to be broken since ages and broke the ath5k EEPROM extraction. Reported-by: Mohammed Berdai <mohammed.berdai@gmail.com> Signed-off-by: Mathias Kresin <dev@kresin.me> Acked-by: John Crispin <john@phrozen.org>
* lantiq: switch from 34k to 24kJonas Gorski2016-08-233-3/+3
| | | | | | | GCC treats 24kc and 34kc exactly the same and will generate identical code, so there is no need to tune to 34kc instead of 24kc. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* lantiq: fix building AVM/EVA sysupgrade images on NOR devicesMartin Blumenstingl2016-08-221-1/+3
| | | | | | | | | | | | Device/AVM unconditionally inherits Device/NAND, which changes the sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image as used in the Device/Default template). This moves the Device/NAND call to the FRITZ3370 device definition, as this is the only AVM/EVA device that uses NAND. Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR devices to ensure that the images are not discarded. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: generate switch configuration for BTHOMEHUBV2B.Sigurd Hogsbro2016-08-201-1/+8
| | | | | | | Split from HH3A as it appears to have a different switch. https://en.wikipedia.org/wiki/BT_Home_Hub#Models_and_technical_specifications Signed-off-by: Sigurd Hogsbro <sigurd@hogsbro.org>
* lantiq/xrx200-net: Add support for eth0 as WAN interfaceMartin Schiller2016-08-151-1/+1
| | | | | | | | Use priv->wan instead of priv->id as indicator if packets should go to the Ethernet WAN group (DPID=1) or not (DPID=0). This way, it's independant of interface names or indexes. Signed-off-by: Martin Schiller <mschiller@tdt.de>
* lantiq: add kmod-ledtrig-usbdev to device packages which have usb ledMatti Laakso2016-08-151-5/+5
| | | | | | | | By default USB LEDs are associated with usbdev trigger. However, not all devices which have USB LEDs have kmod-ledtrig-usbdev in their list of default packages. Add it to the relevant devices. Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
* lantiq/xrx200-net: add interrupt for second DMA TX channel to vr9.dtsiMartin Schiller2016-08-151-1/+1
| | | | Signed-off-by: Martin Schiller <mschiller@tdt.de>
* lantiq/xrx200-net: fix "tx ring full" error by introducing second DMA TX channelMartin Schiller2016-08-151-17/+31
| | | | | | | | | | With an own DMA TX channel for each network device (eth0 + eth1) there won't be any "tx ring full" errors any more. This patch also move the spinlocks to the channel level instead of locking the whole xrx200_hw structure. Signed-off-by: Martin Schiller <mschiller@tdt.de>
* lantiq: fix some ethernet driver SMP issuesFelix Fietkau2016-08-111-10/+16
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: enable cpu temp driver for selected boardsMathias Kresin2016-08-103-0/+12
| | | | | | | | According to the author of the cpu temp driver, not all xrx200 boards have a cpu temperature sensor. For that reason enable the sensor only for tested boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: board.d: set lan mac address only where necessaryMathias Kresin2016-08-101-16/+8
| | | | | | | Do not set the lan mac address for boards which having the lan mac address already set in device tree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop duplicate and now unused "lantiq, eth-mac" bindingMathias Kresin2016-08-101-52/+1
| | | | | | | | | | | | The device tree binding and the associated code duplicates functionality already patched into the etop driver. The compatible string isn't used any more. Therefore the whole code can be dropped. The "mac-increment" property allowed to increment a mac address received via kernel cmdline. This functionality isn't used by any device and should be added as etop driver device tree property if required again. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the etop driver DT bindings onlyMathias Kresin2016-08-1014-81/+25
| | | | | | | Use the generic mtd-mac-address dts property to get a mac address from flash instead of the lantiq specific one. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix mac address incrementsMathias Kresin2016-08-1012-12/+1
| | | | | | | | | | | | Use the same mac address increment in device tree source file and userspace. Don't add a mac address increment to either the only mtd mac-address or to all mac-addresses. Fix a typo in the TDW89X0.dtsi file to add an increment. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop orphaned eeprom-handling code branchesMathias Kresin2016-08-101-97/+71
| | | | | | | | | | All device tree nodes are using the named properties now and the code path handling the reg property isn't required any more. The code related to the ath,eep-flash property has been reformatted to be better readable. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use ath, eep-flash/mac-offset for ath eep nodesMathias Kresin2016-08-105-15/+15
| | | | | | | No functional change, just easier to get what's the purpose of the hex values. Signed-off-by: Mathias Kresin <dev@kresin.me>
* Revert "kernel: remove long obsolete gpio spi controller driver patch"Felix Fietkau2016-08-041-3/+3
| | | | This reverts commit 9e62a7668c4085563a907da51a08819c88d04f33.
* kernel: remove long obsolete gpio spi controller driver patchFelix Fietkau2016-08-041-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: add cpu temperatur sensor driver for xrx200Florian Eckert2016-08-033-0/+171
| | | | Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
* build: remove MIPS dsp/dsp2 CPU_SUBTYPEFelix Fietkau2016-08-033-3/+0
| | | | | | | There does not seem to be any meaningful difference in generated code. This will save some time and space on snapshot builds Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: enable missing ath10k firmware for BT Home Hub 5AFelix Fietkau2016-08-011-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 15:10:18 +0000