aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq
Commit message (Collapse)AuthorAgeFilesLines
...
* lantiq: kernel 4.14: cleanup dts filesMathias Kresin2018-02-2055-4194/+4033
| | | | | | | Move common used parts to dtsi. Add labels to nodes and reference nodes via labels in dts files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: fix usbMathias Kresin2018-02-202-0/+62
| | | | | | | | | | On danube the USB0 registers are at 1e101000 similar to all other lantiq SoCs. On Danube and AR9 the USB core is connected to the AHB bus, hence we need to enable the AHB Bus as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: autoselect matching vr9 rev firmwareMathias Kresin2018-02-201-0/+45
| | | | | | | | | | | | Add a custom xrx200 ethernet phy compatible to load the firmware matching the vr9 revision without specifing an expected revision. We have quite a few boards in the tree were later produced ones are using a more recent vr9. It is impossible to distinguish which revision of the vr9 is used without opening the case and removing a heatsink for some of them. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: don't use CPU interrupt controller IPI IRQ domain supportMathias Kresin2018-02-201-0/+271
| | | | | | | | | | | | | | | | This reverts kernel commit 1eed40043579 ("MIPS: smp-mt: Use CPU interrupt controller IPI IRQ domain support"). With the patch applied, the kernel hangs during boot if SMP is active. The Lantiq IRQ controller gets registered first and it directly handles the MIPS native SW1/2 and HW0 - HW5 IRQs. It looks like this controller already registers IRQ 0 - 7 and the generic driver only gets the following IRQs starting later. The upstream discussion can be found at https://www.linux-mips.org/archives/linux-mips/2017-05/msg00059.html. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: select MFD SYSCON for aseMathias Kresin2018-02-201-0/+24
| | | | | | Enable syscon to use it for the RCU MFD on Amazon SE as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: update patches and configHauke Mehrtens2018-02-2035-3208/+333
| | | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: kernel 4.14: copy patches, config and dts filesHauke Mehrtens2018-02-20114-0/+28761
| | | | | | | This just copies the patches, configuration and dts files into the directories hich are used for kernel 4.14. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: make dts files and kernel config kernel version specificMathias Kresin2018-02-2080-2/+1
| | | | | | | | | | Move the devicetree source files to a kernel specific directory in preparation of adding kernel 4.14 support. Rename the subtarget kernel config files to match a specific kernel version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: rename gphy firmwareMathias Kresin2018-02-2019-30/+30
| | | | | | | | | | Rename the gphy firmware to match the name requested by kernel 4.14 and update the devicetree source files to use the new name. Update the u-boot lantiq Makefile to be compatible with the new names as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: move nand_do_upgrade call to platform_do_upgradeMathias Kresin2018-02-161-3/+4
| | | | | | | | | | Calling nand_do_upgrade() from platform_pre_upgrade() was deprecated with 30f61a34b4cf ("base-files: always use staged sysupgrade"). Update the platform upgrade code to use platform_do_upgrade() for NAND images as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: remove obsolete sysupgrade watchdog killMathias Kresin2018-02-161-9/+0
| | | | | | | | | The watchdog kill command was meant for busybox watchdog. Busybox watchdog was replaced by the procd watchdog mid 2013 with commit df7ce9301a25 ("busybox: disable the watchdog utility by default"), which makes the kill command obsolete since quite some time. Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: replace uses of OpenWrt with $(VERSION_DIST)Felix Fietkau2018-02-051-1/+1
| | | | | | This makes the distribution name more configurable. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: add config option KERNEL_MIPS_FPU_EMULATORYousong Zhou2018-01-291-1/+0
| | | | | | | To make it more accessible for nodejs users to configure and run a build on mips target lacking hardware fpu Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* lantiq: create ATM/PTM interfaces with dsl as netdev nameMathias Kresin2018-01-102-1/+13
| | | | | | | | | | | | | | | | | | | | | Renaming an atm etherbride using 'ip link' (via hotplug) is racy since the original netdev might disappear before br2684ctl has finished appling it's setting: local2.notice br2684ctl[1667]: Interface "nas0" created sucessfully local2.notice br2684ctl[1667]: Communicating over ATM 0.8.35, encapsulation: LLC kern.info kernel: dsl0: renamed from nas0 kern.err kernel: br2684:br2684_regvcc: tried to attach to non-existent device local2.err br2684ctl[1667]: Could not configure interface:No such device or address By passing the final used netdev name to br2684ctl_wrap another race condition workaround will be enabled again. Change the lantiq ptm driver to create a netdev with the name dsl as well. Albeit the rename via 'ip link' works fine so far, using a different approach for ptm then atm could be confusing. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix wbmr-hp-g300h image metadataMathias Kresin2018-01-041-2/+2
| | | | | | | The Annex A and Annex B version are using the same (old) userspace boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix dts compatible stringThomas Nixon2017-12-292-2/+2
| | | | | | | | | | This was broken in 7bab49fd ("lantiq: add compatible strings to dts files"), causing for the dm200 garbled serial output during boot, and likely other issues. Signed-off-by: Thomas Nixon <tom@tomn.co.uk> [fix the compat string of the P2601HNFX as well] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: remove DSL_ChipSetHWVersion from status informationMartin Schiller2017-12-231-4/+2
| | | | | | | | | | | | The value DSL_ChipSetHWVersion is fetched from the dsl frontend via the dsl_control service, but not really provided by the dsl frontend firmware and for now always "UNKNOWN". The lantiq support told us that this information wouldn't be provided in the foreseeable future, so let's remove this useless "UNKNOWN" information. Signed-off-by: Martin Schiller <ms@dev.tdt.de>
* kernel: Update kernel 4.9 to 4.9.70Hauke Mehrtens2017-12-192-2/+2
| | | | | | Runtime tested on lantiq. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: sync image filename with boardnameMathias Kresin2017-12-162-185/+227
| | | | | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. While at it, normalise the image filenames by using only lower case characters and bin as file extension for sysupgrade images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop unused variable from image build codeMathias Kresin2017-12-161-3/+0
| | | | | | | Remove the DEVICE_PROFILE variable. The variable isn't used at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the generic board detectMathias Kresin2017-12-161-19/+0
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add missing model namesMathias Kresin2017-12-161-0/+1
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: remove the former board name from device tree modelMathias Kresin2017-12-1660-60/+60
| | | | | | | Remove the former used board name from the device model property and use the model name as it is. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the compatible string as board nameMathias Kresin2017-12-169-67/+131
| | | | | | | | | | | Use the first compatible string as board name in userspace. Add the new board name as well as the former used board name to the image metadata to keep compatibilty with already deployed installations. Don't add the former used boardname for boards which exists only in master or evaluation boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop SoC name from eval boards compatible stringMathias Kresin2017-12-1611-11/+11
| | | | | | Keep it in the same format as used for the other eval boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add compatible strings to dts filesMathias Kresin2017-12-1653-0/+59
| | | | | | The compatible string is mandetory for devicetree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: unify get_dt_led helper functionChristian Lamparter2017-12-143-23/+10
| | | | | | | | | | | | | | Lantiq and IPQ806X (which includes IPQ40XX) both define the same custom function {ipq806x|lantiq}_get_dt_led. This patch moves the function into the base-file package at lib/functions/leds.sh to make it more accessible for other targets as well. Cc: Mathias Kresin <dev@kresin.me> Cc: John Crispin <john@phrozen.org> Cc: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-1/+3
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: dgn3500 drop worldwide suffixMathias Kresin2017-12-111-6/+6
| | | | | | | | | | Remove the WW suffix, everything without a region suffix is world wide anyway. While at it, normalise the image filenames by using only lower case characters. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: nand: drop ubifs imagesMathias Kresin2017-12-112-2/+2
| | | | | | | | | | | | | | | Users are confused which image type they should use and there are more drawbacks than adavantages in using a r/w ubifs rootfs in constrast to a read-only squashfs rootfs like: - less available free flash space due to better compression of squashfs images - no support for factory reset due to r/w filesystem - possibility to break failsafe due to r/w filesystem Therefore, drop support for r/w ubifs rootfs images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* merge: targets: update image generation and targetsZoltan HERPAI2017-12-081-1/+1
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* kernel: bump 4.9 to 4.9.67Stijn Tintel2017-12-071-1/+1
| | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch - generic/190-3-5-e1000e-Fix-return-value-test.patch - generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch - generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch - ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function Update patches that no longer apply: - layerscape/815-spi-support-layerscape.patch - ramips/0099-pci-mt7620.patch Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.9 to 4.9.63Koen Vandeputte2017-11-221-1/+1
| | | | | | | | | | | Refreshed all patches. Removed upstreamed parts. Compile-tested: cns3xxx, imx6, mvebu, layerscape Run-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* lantiq: add missing macaddr retrieval for Netgear DGN3500Daniel Gimpelevich2017-11-081-0/+2
| | | | | | | The MAC addresses were not being set for LAN and WAN. This will now use the same MAC mechanism as the rest of the target. Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
* lantiq: xway: rename nas0/ptm0 to dsl0Mathias Kresin2017-10-253-9/+2
| | | | | | | | | | | This change makes it possible to configure the wan/dsl ppp interface settings independantly from the used TC-Layer (ATM/PTM). By using dsl0 as interface name as for the xrx200 we can get rid of a few conditionals which were introduced because of the different default TC-Layer in xway and xrx200. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: match default adsl annex and firmwareMathias Kresin2017-10-251-2/+31
| | | | | | | | | | Set a default Annex matching the the annex of the selected adsl firmware. Set Annex B for xrx200 board which are known to have an ADSL hybrid for Annex B. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add missing default lan interfaceMathias Kresin2017-10-251-0/+2
| | | | | | | | | With removing the boards from the the default case to fix the xDSL WAN MAC-Address, the setting for the default LAN interface wasn't added. Fixes: 92a12c434ca3 ("lantiq: fix avm fritz box mac addresses") Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ARV752DPW22: fix wireless mac addressMathias Kresin2017-10-181-0/+1
| | | | | | | | | | The ARV752DPW22 has the same generic mac address in the EEPROM as it was already noticed for other lantiq boards using a ralink wireless. Use the base mac address from the boardconfig partition as it is done by the stock firmware. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ARV752DPW22: set correct wireless led triggerMathias Kresin2017-10-181-0/+3
| | | | | | | The ARV752DPW22 has a ralink based wireless and can not use the ath9k only phy0tpt trigger. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: rename nas0/ptm0 to dsl0Martin Schiller2017-10-153-2/+59
| | | | | | | | | | | | | This change makes it possible to configure the wan/dsl ppp interface settings independantly from the used TC-Layer (ATM/PTM). Now you can move a device from an ADSL/ATM port to an VDSL/PTM port without any configuration changes for example. Signed-off-by: Martin Schiller <ms@dev.tdt.de> [use the dsl0 interface name for the default netdev trigger in 01_led, add ip dependency] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: update and refresh patchesStijn Tintel2017-10-082-37/+36
| | | | | | | | | | The lantiq patch 0028-NET-lantiq-various-etop-fixes.patch and sunxi patch 0051-stmmac-form-4-11.patch no longer applied after applying the the "generalize napi_complete_done()" patch. Update them so they apply, and refresh patches while at it. Fixes: 9aeb7ce8dc5 ("generic: net: generalize napi_complete_done") Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* lantiq: drop phy id specfic compatible stringMathias Kresin2017-10-072-3/+3
| | | | | | | | | | | | With kernel commit 7630ea4bda18 ("Documentation: net: phy: improve explanation when to specify the PHY ID") the purpose of using phy id specific compatibles was clarified. Remove the phy id specific compatibles since they are meant to be used if the phy reports an incorrect or no phy id at all. Reported-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: remove gen_nand compatible stringMathias Kresin2017-10-077-7/+7
| | | | | | | | | | | | | The generic nand driver fails to load with: gen_nand 14000000.nand-parts: platform_nand_data is missing gen_nand: probe of 14000000.nand-parts failed with error -22 and the xway-nand driver is used afterwards. Drop the gen_nand compatible to get rid of the error message. Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: add mktplinkfw2 hardcoded values to makefileThibaut VARÈNE2017-10-061-3/+12
| | | | | | | | | | | This patch adds all the board-specific values currently hardcoded in mktplinkfw2.c back to the respective device declarations in the makefiles. The rationale is to avoid modifying the source code every time a new board or board variant is added. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* lantiq: ase: enable USB and wirelessMathias Kresin2017-10-041-2/+4
| | | | | | | | | | Add the missing USB related kernel config options to target config. Enable wireless as well, wireless is supported via USB. Fixes compile/packaging errors with the libertas wireless kernel module. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ase: fix SPI supportMathias Kresin2017-10-043-1/+2
| | | | | | | | | | Do not disable SPI in the subtarget, otherwise the SPI driver can not be used. Disable SPI by default and enable it in the board specific device tree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: select PCI support in subtargetsMathias Kresin2017-10-044-8/+23
| | | | | | | | | | | | | | | | AmazonSE and Falcon do not have support for PCI and it can't be unselected in the subtarget kernel config. This way the enabled PCI support is inherit from the higher level config to the subtarget. If CONFIG_PCI is selected, PCI_SUPPORT will be autoselected as well and all packages depending on this config symbol will be build and at least some of them fail due to missing pci functions. The issue can be observed if all kmods and all non-shared packages are build. Fix the issue by enabling PCI support only in subtargets with PCI support. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: ase: cleanup kernel configMathias Kresin2017-10-041-2/+0
| | | | | | | | The subtarget kernel config options CONFIG_CC_OPTIMIZE_FOR_SIZE and CONFIG_HAVE_IRQ_EXIT_ON_IRQ_STACK are already set by the target or global kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xway: cleanup kernel configMathias Kresin2017-10-041-29/+0
| | | | | | | | | | CONFIG_SPI_LANTIQ was replaced by CONFIG_SPI_LANTIQ_SSC with the switch to the upstreamed driver. All other removed subtarget kernel config options are already set by the target specific or global kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: cleanup kernel configMathias Kresin2017-10-041-3/+8
| | | | | | | | | | | CONFIG_MTSCHED & CONFIG_PERFCTRS were never defined in the kernel. CONFIG_LANTIQ_PHY was replaced by CONFIG_INTEL_XWAY_PHY with the switch to the upstreamed driver. Add autoselected dependecies to the kernel config. Signed-off-by: Mathias Kresin <dev@kresin.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-06-29 14:52:25 +0000