aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/image
Commit message (Collapse)AuthorAgeFilesLines
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-2/+2
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix DM200 boot with fake uImage headersThomas Nixon2018-03-181-0/+4
| | | | | | | | | | | | | | The latest bootloader versions load the firmware into memory and call `chk_dniimg` (defined in Netgear GPL release), which expects to find three consecutive block-aligned uImages. Add two fake uImage headers after the kernel to fool this check. This wastes up to 128k of space for alignment. The alternative would be to put the rootfs in a second uImage, but this would limit the firmware size to 0x710000 (the number of bytes loaded and verified by the bootloader) instead of 0x7b0000 (the size of the firmware partition). Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* lantiq: fix AVM initramfs imageValentin Spreckels2018-03-181-0/+1
| | | | | | Create an initramfs that can be used with the EVA bootloader. Signed-off-by: Valentin Spreckels <Valentin.Spreckels@Informatik.Uni-Oldenburg.DE>
* lantiq: make dts files and kernel config kernel version specificMathias Kresin2018-02-201-2/+1
| | | | | | | | | | Move the devicetree source files to a kernel specific directory in preparation of adding kernel 4.14 support. Rename the subtarget kernel config files to match a specific kernel version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: replace uses of OpenWrt with $(VERSION_DIST)Felix Fietkau2018-02-051-1/+1
| | | | | | This makes the distribution name more configurable. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix wbmr-hp-g300h image metadataMathias Kresin2018-01-041-2/+2
| | | | | | | The Annex A and Annex B version are using the same (old) userspace boardname. Update the SUPPORTED_DEVICES to allow an update from lede-17.01. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: sync image filename with boardnameMathias Kresin2017-12-162-185/+227
| | | | | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. While at it, normalise the image filenames by using only lower case characters and bin as file extension for sysupgrade images. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop unused variable from image build codeMathias Kresin2017-12-161-3/+0
| | | | | | | Remove the DEVICE_PROFILE variable. The variable isn't used at all. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the compatible string as board nameMathias Kresin2017-12-162-0/+60
| | | | | | | | | | | Use the first compatible string as board name in userspace. Add the new board name as well as the former used board name to the image metadata to keep compatibilty with already deployed installations. Don't add the former used boardname for boards which exists only in master or evaluation boards. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-1/+3
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: dgn3500 drop worldwide suffixMathias Kresin2017-12-111-6/+6
| | | | | | | | | | Remove the WW suffix, everything without a region suffix is world wide anyway. While at it, normalise the image filenames by using only lower case characters. Signed-off-by: Mathias Kresin <dev@kresin.me>
* merge: targets: update image generation and targetsZoltan HERPAI2017-12-081-1/+1
| | | | Signed-off-by: Zoltan HERPAI <wigyori@uid0.hu>
* build: add mktplinkfw2 hardcoded values to makefileThibaut VARÈNE2017-10-061-3/+12
| | | | | | | | | | | This patch adds all the board-specific values currently hardcoded in mktplinkfw2.c back to the respective device declarations in the makefiles. The rationale is to avoid modifying the source code every time a new board or board variant is added. Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* lantiq: ACMP252: clean up device modulesDaniel Golle2017-08-291-4/+7
| | | | | | | Install kmod-rt2800-pci instead of only the rt2x00 library. Fixes missing wireless interface on AudioCodes AC-MP252. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* lantiq: add Netgear DM200 supportThomas Nixon2017-07-071-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear DM200 is an inexpensive VDSL modem: CPU: VRX220 MIPS 34Kc 5.6 @ 500Mhz RAM: 64MiB Flash: 8MiB Ethernet: 1x100M DSL: VDSL2+, ADSL2+ reset button, 3x bi-color LEDs Serial port is 115200 baud, on the 4 pin header; pins from the bottom to top are GND, RX, TX. To upgrade from the vendor firmware, upload factory.img The DM200 bootloader supports flashing over TFTP; hold the reset button while powering on the device, and wait for the power light to start flashing green before releasing. The device is now listening on 192.168.0.1/24, and can be sent a factory.img or a netgear image with a TFTP put. Once the image is loaded, it will be written to the flash, and the device will reboot; this will take a few minutes. Thanks to Edward O'Callaghan and Baptiste Jonglez, who implemented their own ports for this device and provided valuable feedback. Signed-off-by: Thomas Nixon <tom@tomn.co.uk>
* lantiq: use img file extension for DGN3500 factory imagesMathias Kresin2017-07-041-5/+5
| | | | | | | | The Netgear UI in basic mode refuses the upgrade file if the the fileextension is not img. The expert/advanced mode accepts any fileextension. Use img to make it work in any case. Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: move mktplinkfw2 related commands to image-commands.mkPiotr Dymacz2017-06-291-17/+8
| | | | | | | | | There are already two targets (lantiq, ramips) which use mktplinkfw2 tool for creating images. This de-duplicates code, introduces two new build commands: tplink-v2-header, tplink-v2-image and makes use of them in place of old, (sub)target specific ones. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* build: move lzma2eva build step to image-commands.mkMathias Kresin2017-06-241-3/+4
| | | | | | | Move it to image-commands.mk so that it can used by other targets with eva based boards as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add Allnet ALL0333CJ supportTino Reichardt2017-06-031-0/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Allnet ADSL2+ Modem ALL0333CJ. Specifications: - SoC: Amazon-SE - RAM: 16MB - Storage: 4MB NOR FLash - LEDs: Power, Ethernet, DSL (Sync) - Buttons: 1x Reset Button (not currently supported, will be done) - 1x Ethernet-Port: 1x RJ45 10/100BaseTX - 1x WAN-Port: AnnexB & J, G.992.1(ADSL), G.992.3(ADSL2), G.992.5(ADSL2+) Installation: - can be done via telnet+tftp or serial console - default passwords: - via telnet (root:admin) - via webinterface http://172.16.1.254:8235/ (admin:coolwhite) Installation via telnet / tftp: host: # your own host must have an tftpd daemon, then do this: host: ifconfig eth0:172 172.16.1.1 up host: # telnet to allnet modem, root:admin host: telnet 172.16.1.254 modem: # kill this daemon, it spams your console modem: killall dsl_cpe_control modem: # change to some place in ram: modem: cd /ramdisk/tftp_upload modem: # load lede-lantiq-ase-ALL0333CJ-squashfs-sysupgrade.bin alias uImage modem: tftp -g -r uImage 172.16.1.1 modem: # load these extra tools from your tftpd via: modem: # source: https://github.com/mcmilk/uboot-utils/releases/download/0.1/mips32.tar.gz modem: tftp -g -r flashwrite 172.16.1.1 modem: tftp -g -r fw_setenv 172.16.1.1 modem: tftp -g -r fw.conf 172.16.1.1 modem: ln -s fw_setenv fw_printenv modem: chmod +x * modem: ./fw_setenv disable_recovery y modem: ./fw_setenv kernel_addr 0xb0010000 modem: ./flashwrite /dev/mtd/1 uImage 0 Installation via serial line at uboot: uboot: # erase everything exept bootloader uboot: protect on b0000000 +10000; protect on b03f0000 +10000 uboot: erase all uboot: # get new firmware via tftp: uboot: tftpboot 0x80100000 uImage; setenv kernel_addr 0xb0010000 uboot: # copy to flash: uboot: cp.b 0x80100000 $(kernel_addr) $(filesize) uboot: # disable proprietary image checking: uboot: setenv disable_recovery=y; saveenv uboot: # reboot with LEDE ;) uboot: reset Ethernet works as expected, DSL syncronization does not work properly currently, I am working on this issue. Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
* lantiq: enable Netgear DGN1000B image buildTino Reichardt2017-06-031-0/+14
| | | | | | | | | | | Enable the building of Netgear DGN1000B images. I have an example device here, but it was not tested currently. Also WLAN and USB is not ready in the moment. This is just the proper way, so that developing on this device is known to be done in the near future. Signed-off-by: Tino Reichardt <milky-lede@mcmilk.de>
* lantiq: add support for the Alpha ASL56026Alex Maclean2017-03-081-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ASL56026 is a VDSL2 router with dual 100mbit ethernet, also known as the ECI B-FOCuS V-2FUb/I. CPU: Lantiq XRX268 v1.1 at 333MHz Modem: Lantiq VRX208 RAM: 32MiB DDR2 at 167MHz Flash: 8MiB NOR, Spansion S29GL064N90TF04 UART is at JP1: Pin 1 TX Pin 2 GND Pin 3 +3.3V Pin 4 NC Pin 5 RX Boot selection pins are exposed via several resistor jumpers: boot_sel0 is at J15, on the rear of the board. Default is high. boot_sel1 is at J3, next to the flash - it is also the flash CE# pin. Default is low. boot_sel2 is at J12, directly below the SoC. Default is low. boot_sel3 is at J16, on the rear of the board. Default is low. The boot_sel pins should never be shorted, the jumper must be moved or a lower value resistor used to change the pull (existing resistors are 4k7, 1k should work) To install with the stock bootloader you must break the built in image selection process which uses at least the following vars: f_upgrade_addr, f_upgrade2_addr, loadaddr, kernel_addr, activeregion, committedregion This is done by setting loadaddr and both f_upgrade_addr vars to the same address: VR9 # setenv loadaddr 0xB0040000 VR9 # setenv f_upgrade_addr 0xB0040000 VR9 # setenv f_upgrade2_addr 0xB0040000 VR9 # saveenv Then flash the firmware image: VR9 # tftpboot 0x81000000 lede-lantiq-xrx200-ASL56026-squashfs-sysupgrade.bin VR9 # erase B0040000 +${filesize} VR9 # cp.b 0x81000000 0xB0040000 ${filesize} Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* lantiq: clarify VG3503J nameAlex Maclean2017-03-081-1/+1
| | | | | | | Append the ECI model to the device name, to avoid confusion with the older model. Signed-off-by: Alex Maclean <monkeh@monkeh.net>
* lantiq: select kmod-mt7603 instead of kmod-mt76 for WBMR-300HPDFelix Fietkau2017-02-271-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix brnImage signature for the VGV7510KW22BRN imagesMathias Kresin2017-01-281-2/+2
| | | | | | | | The VGV7510KW22BRN and VGV7519BRN do not have the same brnImage signature. It was accidentally changed with ba42c1d ("lantiq: un-macro the image building code"). Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix falcon buildJohn Crispin2016-12-251-1/+1
| | | | | | | | | The following commit changed the build templates name but forgot to update the TARGET_DEVICES variable properly. commit f9226158bed52aeae408730 (lantiq: rename EASY98000 to EASY98000NOR) Signed-off-by: John Crispin <john@phrozen.org>
* lantiq: rename EASY98000 to EASY98000NORHauke Mehrtens2016-12-241-2/+1
| | | | Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: use ath9k device tree bindings binding/owl-loaderMartin Blumenstingl2016-11-292-16/+17
| | | | | | | | | | | | | | | | | This moves the extraction of the eeprom/calibration data to a hotplug firmware script. Additionally it modifies all .dts to configure ath9k directly from within the .dts. The owl-loader approach enables support on devices with exotic eeprom data locations (such as unaligned positions on the flash or data inside an UBI volume). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> [add ath9k caldata mac address patcher] [fixes DGN3500 wifi mac] [fixes BTHOMEHUBV3A wifi mac] [set invalid mac for BTHOMEHUB2B, FRITZ3370, FRITZ7320 & FRITZ7360SL to restore previous random mac behavior] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add Falcon supportHauke Mehrtens2016-11-271-0/+81
| | | | | | | | | | | | This adds support for the Intel Falcon SoC for GPON. Support for the Falcon SoC was removed in commit c8218363951 svn rev: 40392 from OpenWrt, this commit adds it again. This patch adds a new subtarget for the Falcon SoC, but it still misses all the drivers needed to control the GPON part. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: add swconfig to the default packagesMathias Kresin2016-11-271-44/+26
| | | | | | | | | | | | The DEVICE_PACKAGES are not included in the initramfs image in case TARGET_PER_DEVICE_ROOTFS is set. This might produces initramfs images with a not working network configuration because of a missing swconfig. Workaround the issues by adding the essential swconfig package to the default packages selection and deselect swconfig for boards not having swconfig included before via device packages. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add missing metadata for tp-link imagesFelix Fietkau2016-11-211-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: use dwc2 by default on danubeBen Mulvihill2016-11-211-13/+13
| | | | | | Use dwc2 by default on all danube boards. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
* lantiq: run append-metadata before check-size to fix build errorsFelix Fietkau2016-11-191-4/+4
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: append metadata to imagesFelix Fietkau2016-11-191-5/+6
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: add tapi/vmmc to VGV7519 defaultsdpeddi2016-11-161-2/+2
| | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net>
* lantiq: add tapi/vmmc to VGV7510KW22 defaultsEddi De Pieri2016-11-161-2/+2
| | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net>
* lantiq: use new build code for DGN3500Mathias Kresin2016-10-191-99/+36
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: drop lzma-loaderMathias Kresin2016-10-1924-2792/+0
| | | | | | It isn't used any more. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: rework VG3503J imageMathias Kresin2016-10-191-50/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Use the new image build code and remove the lzma loader. The lzma loader was used to cheat the signature validation of the bootloader and I found another way to do this. To migrate boards already using LEDE/OpenWrt to the new image the following steps need to be done once: VR9 # run reset_uboot_config VR9 # reset VR9 # setenv ethaddr AA:BB:CC:DD:EE:FF VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The mac address is printed on the label at the bottom of the case. The following steps are need to be done during first install: VR9 # setenv preboot ping 1.1.1.1\;bootm 0xb001f000 VR9 # saveenv VR9 # tftp 0x81000000 lede-lantiq-xrx200-VG3503J-squashfs-sysupgrade.bin VR9 # erase 0xb0020000 $(filesize) VR9 # cp.b 0x81000000 0xb0020000 $(filesize) The image uses the uImage firmware splitter now instead of hardcoded kernel and rootfs partitions. The firmware partition size was extended to use flash space that was reserved for partitions required only by the ECI firmware. Due to the changes an upgrade to a later LEDE revision from a running LEDE is supported now. A default switch config was added and the device uses the same MAC addresses as the ECI firmware now instead of the same for all VG3503J. Signed-off-by: Mathias Kresin <dev@kresin.me>
* switch to the new usbport LED triggerRafał Miłecki2016-10-192-21/+21
| | | | | | | This makes init.d script handle existing UCI entries using the new trigger. It also switches all targets to use its package. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* lantiq: use wpad-mini for WBMR boardsMathias Kresin2016-10-151-4/+2
| | | | | | | | | | The WBMR boards are the only ones in the whole tree selecting the wpad and hostapd-utils package by default. Remove the wps uci-default script as well, there is no obvious reason why the wps config need to be set only for this board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix BTHOMEHUBV2B default packagesMathias Kresin2016-10-061-1/+1
| | | | | | | | | | Due to the introduced double whitespace the default package selection isn't applied. This leads to errors like a not working networking because of a missing swconfig binary. Fixes FS#208. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix usb leds/triggerMathias Kresin2016-10-051-5/+5
| | | | | | | | | | | Add USB led aliases to boards having an led which is meant to be used as USB led according to the manuals. Remove the kmod-ledtrig-usbdev from the default package selection for boards not having an USB led. Add the kmod-ledtrig-usbdev to boards where it is missing. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: use k as unit suffix for blocksizeMathias Kresin2016-09-041-2/+2
| | | | | | | Use k as unit suffix for kilobyte to have a the same unit regardless of the used filesystem. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix building AVM/EVA sysupgrade images on NOR devicesMartin Blumenstingl2016-08-221-1/+3
| | | | | | | | | | | | Device/AVM unconditionally inherits Device/NAND, which changes the sysupgrade image to sysupgrade-tar (instead of a "raw" sysupgrade image as used in the Device/Default template). This moves the Device/NAND call to the FRITZ3370 device definition, as this is the only AVM/EVA device that uses NAND. Additionally we have to define the IMAGE_SIZE for the AVM/EVA NOR devices to ensure that the images are not discarded. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: add kmod-ledtrig-usbdev to device packages which have usb ledMatti Laakso2016-08-151-5/+5
| | | | | | | | By default USB LEDs are associated with usbdev trigger. However, not all devices which have USB LEDs have kmod-ledtrig-usbdev in their list of default packages. Add it to the relevant devices. Signed-off-by: Matti Laakso <matti.laakso@outlook.com>
* lantiq: enable missing ath10k firmware for BT Home Hub 5AFelix Fietkau2016-08-011-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* image: add a helper variable for getting kernel/rootfs from within image ↵Felix Fietkau2016-07-312-5/+5
| | | | | | Build/* templates Signed-off-by: Felix Fietkau <nbd@nbd.name>
* build: rename sysupgrade-nand to sysupgrade-tarJo-Philipp Wich2016-07-291-1/+1
| | | | | | | Now that the "sysupgrade-nand" step is used by non-NAND targets as well, rename it to "sysupgrade-tar" to make it more generic. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* lantiq: fix image creation of P2812HNUF3 & BTHOMEHUBV3AMathias Kresin2016-07-221-2/+2
| | | | | | | | Both devices were converted to the new image build code but still using the LegacyDevice define. Therefore an image isn't created for the mentioned devices. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: convert remaining xway NAND devices to new image build codeFelix Fietkau2016-07-201-65/+8
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 08:18:15 +0000