aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/lantiq/dts/VGV7519.dtsi
Commit message (Collapse)AuthorAgeFilesLines
* lantiq: make dts files and kernel config kernel version specificMathias Kresin2018-02-201-298/+0
| | | | | | | | | | Move the devicetree source files to a kernel specific directory in preparation of adding kernel 4.14 support. Rename the subtarget kernel config files to match a specific kernel version. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: rename gphy firmwareMathias Kresin2018-02-201-2/+2
| | | | | | | | | | Rename the gphy firmware to match the name requested by kernel 4.14 and update the devicetree source files to use the new name. Update the u-boot lantiq Makefile to be compatible with the new names as well. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: add compatible strings to dts filesMathias Kresin2017-12-161-0/+2
| | | | | | The compatible string is mandetory for devicetree source file. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: xrx200: use vlan for ethernet wan portMathias Kresin2017-03-111-10/+0
| | | | | | | | | | | | | | | | | | | | | | | Using the lantiq,wan device tree property for one interface node and the lantiq,switch device tree property for another interface node at the same time was never intended/isn't supported at the moment. The property is meant to be used in two phy operation mode where one phy is assigned to an interface without lantiq,* device tree property and the other phy is assigned to an interface with the lantiq,wan device property to have two netdevs. If both properties are used at the same time, the lantiq,wan interface is shown as independent netdev but not able to operate independent. The port needs to be managed via swconfig. These dependency is not obvious and fooled already a lot of users. Add a default WAN vlan for xrx200 devices having an ethernet WAN port and remove the lantiq,wan device tree property. Leave it up to the user to set the ethernet WAN port as default WAN interface or to use this port as additional LAN port. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: enable SMP for XRX200Felix Fietkau2017-02-011-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* lantiq: fix console printHauke Mehrtens2017-01-051-1/+1
| | | | | | | | | | | | | | | | | | The boot loader of many boards provides a kernel boot argument with a broken console parameter to the kernel. This will be taken before the stdout-path defined in device tree and the serial will not work on this board. Multiple boards are affected by this problem, so revert this patch for all boards. Later we can remove the boot arguments from the device tree again, after the individual board was checked to work. This partly reverts this commit: commit 4995c64857a09c4cc92238ba0bd52cdb06c4c581 Author: Martin Blumenstingl <martin.blumenstingl@googlemail.com> Date: Sun Dec 11 21:55:00 2016 +0100 lantiq: specify console using stdout-path instead of cmdline argument Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* lantiq: remove "init" kernel command line parameter from bootargsMartin Blumenstingl2016-12-121-1/+1
| | | | | | | | | | /etc/preinit has been the default init-script for a very long time (at least since Linux 2.6.30 in OpenWrt). Remove the kernel command line "init" parameter to get rid of duplicate and inconsistent definitions of this parameter (some boards, like FRITZ3370 for example did not use it at all, while it's just copy and paste on others). Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: specify console using stdout-path instead of cmdline argumentMartin Blumenstingl2016-12-121-1/+1
| | | | | | | | Use devicetree's /chosen/stdout-path instead of the kernel command line (embedded in the .dts-files) to specify the serial console. Using the chosen node is recommended on devicetree based platforms. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
* lantiq: fix image validation errorsMathias Kresin2016-12-041-3/+0
| | | | | | | The boards did not have the name set that is expected during metadata validation on sysupgrade. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix button keys codes used in dtsMathias Kresin2016-11-271-1/+1
| | | | | | Use keycodes that matches the intended use case based on the label. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: enable VMMC for VGV7519dpeddi2016-11-161-1/+10
| | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net>
* treewide: dts: use keycode defines from input dt-bindingMathias Kresin2016-11-131-0/+2
| | | | | | | | | | | | | | | | | | | | | All compiled device tree files not mentioned are binary identical to the former ones. Fix the obvious decimal/hex confusion for the power key of ramips/M2M.dts. Due to the include of the input binding header, the BTN_* node names in: - ramips/GL-MT300A.dts - ramips/GL-MT300N.dts - ramips/GL-MT750.dts - ramips/Timecloud.dts will be changed by the compiler to the numerical equivalent. Move the binding include of lantiq boards to the file where they are used the first time to hint the user where the values do come from. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use the device tree bindings from rt2x00 driverMathias Kresin2016-11-091-10/+14
| | | | | | | | | | | | | Set a device specific wireless mac address for ARV7506PW11, VGV7519 and VGV7510KW22. The one from the EEPROM is a generic one and the same on all boards. Use the wifi@0,0 label and the pci0,0 compatible string for the ARV7519PW and ARV7525PW since the pci vendor and device id is unknown. It should work anyway since the compatible string isn't evaluated (yet). Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: fix VGV7519 and VGV7510KW22 mac addressesMathias Kresin2016-11-091-1/+1
| | | | | | | | | | | | | | | | | The VGV7510KW22 stock firmware uses the following mac-addresses: lan (ifno 1): AA:BB:CC:DD:EE:60 wlan (ifno 2): AA:BB:CC:DD:EE:61 atm0 (ifno 3): AA:BB:CC:DD:EE:62 atm1/wan (ifno 4): AA:BB:CC:DD:EE:63 The VGV7519 stock firmware uses the following mac-addresses: lan: AA:BB:CC:DD:EE:EF wlan: AA:BB:CC:DD:EE:EF wan: AA:BB:CC:DD:EE:EE Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: cleanup dts filesMathias Kresin2016-11-031-7/+1
| | | | | | | | | | | | | | - remove not existing properties - remove properties having the same values as the included dtsi - remove nodes which are disabled in the included dtsi and not enabled in dts - replace the deprecated pinctrl-* compatible strings - use the same labels for nodes as the included dtsi - move common used vr9 pci properties to vr9.dtsi - remove the unused stp node from HomeHub 2B devcie tree source file - fix spaces vs. tabs and remove superfluous linebreaks Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: enable cpu temp driver for all vr9 boardsMathias Kresin2016-10-191-4/+0
| | | | | | | Only present on v1.2 vr9 SoCs but the driver takes care to not load on boards having a v1.1 SoC. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: Sanitize device tree filesAndreas Eberlein2016-10-191-26/+26
| | | | | | | | | | The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes. This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend. Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de> [sanitize all device tree files] Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: use aliases device tree node for ledsMathias Kresin2016-10-051-8/+8
| | | | | | The chosen node is clearly the wrong place for aliases. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: enable cpu temp driver for more tested boardsMathias Kresin2016-09-101-1/+5
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7519 - get mac address from board_config partitionMathias Kresin2016-05-271-2/+3
| | | | | | | Use the mac address stored in the board_config partition instead of a static one. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7519 - add vlan supportMathias Kresin2016-05-271-0/+1
| | | | | | Add the lantiq,switch property to enable vlans and setup them up. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7519 - add second usb portMathias Kresin2016-05-271-0/+5
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7519 - cleanup pinmux configurationMathias Kresin2016-05-271-15/+3
| | | | | | | | | | | | Cleanup the pinmux configuration by removing the unused spi node. Nothing is connected to the SPI bus on devices. The stp_out pinmux child node covers the same GPIOs as the already used stp group. The same applies to the gphy-leds_out pinmux node and the "gphy0 led1" as well as "gphy1 led0" groups. Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7519 - remove/merge redundant parts in dtsMathias Kresin2016-05-271-34/+20
| | | | Signed-off-by: Mathias Kresin <dev@kresin.me>
* lantiq: VGV7510KW22/VGV7519 update spi pinmux groupJohn Crispin2016-02-081-1/+1
| | | | | | | | | | | | | With the backport of the kernel 4.5 pinctrl-xway patches (3551609d & 826bca29) the pinmux group "spi" was splitted into "spi_di", "spi_do" & "spi_clk". But the no longer existing group "spi" is still used by some device tree source files. This fixes the detection of the wireless chipset of the VGV7510KW22. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48658
* lantiq: Move the definition of the xrx200-net node to vr9.dtsiFelix Fietkau2016-01-291-92/+81
| | | | | | | | | | This removes a lot of duplicate register and interrupt definitions by moving the xrx200-net definition to vr9.dtsi and making all devices re- use it. Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com> SVN-Revision: 48547
* lantiq: use devicename:colour:function led naming schemeJohn Crispin2016-01-011-35/+35
| | | | | | | | | | | | | | | | The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48042
* lantiq: add support for indicating the boot state using three ledsJohn Crispin2016-01-011-3/+5
| | | | | | | | | | | | | | The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
* lantiq: define default leds in dts filesJohn Crispin2016-01-011-5/+13
| | | | | | | | | | - ARV7525PW: use the power led as dsl led as done by the stock firmware - FRITZ3370: use the info led as internet led - FRITZ7320: use the power led as dsl led as done by the stock firmware Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48037
* vgv7519: support more recent board release with vrx288 v1.2John Crispin2014-10-261-1/+2
| | | | | | | | The existance of this new board has been confirmed and tested by the guy on this commit https://github.com/openwrt-vgv7519/uboot-bin/commit/76fdd8e638f81e324ffe77856481bd147398f6e8 SVN-Revision: 43072
* lantiq: allow pcie to be disabled by dts + vgv7519 fix pci irq + disable ↵John Crispin2014-10-141-1/+5
| | | | | | | | pcie by dts Signed-off-by: Eddi De Pieri <eddi@depieri.net> SVN-Revision: 42907
* lantiq - vgv7519: load rt5362 eeprom from bootloader param patitionJohn Crispin2014-10-061-0/+7
| | | | SVN-Revision: 42824
* lantiq - vgv7519: enable pci busJohn Crispin2014-10-061-2/+3
| | | | SVN-Revision: 42823
* lantiq - vgv7519: remove spi_cs4, since the board use this line for ↵John Crispin2014-10-061-1/+1
| | | | | | something else SVN-Revision: 42822
* lantiq - vgv7519: fix open-drain configuration for stpJohn Crispin2014-10-061-8/+6
| | | | SVN-Revision: 42821
* lantiq - vgv7519: add pci-rst entry into dtsJohn Crispin2014-10-061-0/+6
| | | | SVN-Revision: 42820
* lantiq - vgv7519: remove exin definition copied from dev-board dtsJohn Crispin2014-10-061-8/+0
| | | | SVN-Revision: 42819
* lantiq - vgv7519: we don't have pcie bus so we don't need the reset device ↵John Crispin2014-10-061-5/+0
| | | | | | tree for this board SVN-Revision: 42818
* lantiq - vgv7519: we don't have dual minipci-card so we don't need gnt1-req1 ↵John Crispin2014-10-061-4/+0
| | | | | | for pci handling SVN-Revision: 42817
* lantiq - vgv7519: fix gphy led configuration (this set correct alt function ↵John Crispin2014-10-061-2/+11
| | | | | | to gpio and let peripherials on pci bus to comes up) SVN-Revision: 42816
* lantiq: fix board_id/boardname for VGV7519John Crispin2014-07-161-0/+3
| | | | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net> SVN-Revision: 41672
* lantiq: vgv7519 add missing wps label to dtsJohn Crispin2014-07-141-0/+1
| | | | | | Signed-off-by: Eddi De Pieri <eddi@depieri.net> SVN-Revision: 41655
* lantiq: fixup vgv7519 usb supportJohn Crispin2014-06-161-1/+1
| | | | | | | | https://dev.openwrt.org/ticket/16800 Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 41213
* lantiq: add support for VGV7519 KPN Experia box v8John Crispin2013-09-301-0/+307
Signed-off-by: Maikel Bloemendal <mbloemendal@gmail.com> Signed-off-by: John Crispin <blogic@openwrt.org> SVN-Revision: 38266
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-09 22:36:06 +0000