openwrt/upstream - upstream openwrt

	Commit message (Collapse)	Author	Age	Files	Lines
*	lantiq: Sanitize device tree files	Andreas Eberlein	2016-10-19	1	-19/+19
\| \| \| \| \| \| \| \| \| \|	The device tree file of ARV752DPW uses numbers/hex values for gpio states and input event codes. This cleans it up and uses the available macros from header files. This way the functions are easier to read and comprehend. Signed-off-by: Andreas Eberlein <foodeas@aeberlein.de> [sanitize all device tree files] Signed-off-by: Mathias Kresin <dev@kresin.me>
*	lantiq: use aliases device tree node for leds	Mathias Kresin	2016-10-05	1	-7/+7
\| \| \| \| \| \|	The chosen node is clearly the wrong place for aliases. Signed-off-by: Mathias Kresin <dev@kresin.me>
*	lantiq: mac address setting on BTHOMEHUBV3A	Ben Mulvihill	2016-07-05	1	-2/+1
\| \| \| \| \| \| \| \| \| \|	Rename uboot environment partition on BT Home Hub 3A so that mac address setting works correctly. Also, the mac address field in the ath9k calibration data is not used, and should not be referenced in the dts. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
*	lantiq: move partitions into partion table node	blogic	2016-05-10	1	-25/+31
\| \| \| \| \| \| \| \| \| \|	Starting with kernel 4.4, the use of partitions as direct subnodes of the mtd device is discouraged and only supported for backward compatiblity reasons. Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 49280
*	lantiq: remove read-only flag on two partitions on BTHOMEHUBV3A	John Crispin	2016-04-26	1	-2/+0
\| \| \| \| \| \| \| \| \| \| \|	Remove read-only flag on two partitions on BTHOMEHUBV3A: uboot-config - otherwise fw_setenv command cannot be used. ath9k-cal - so that ath9k calibration data can be copied to the partition on a newly installed board. Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 49250
*	lantiq: use devicename:colour:function led naming scheme	John Crispin	2016-01-01	1	-9/+9
\| \| \| \| \| \| \| \| \| \| \| \| \| \| \| \|	The leds of the following boards are not renamed due to lack of manuals/informations: - ARV7519PW - ARV7510PW22 - ARV4510PW The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't match the leds from the manual or pictures (e.g. there shouldn't be a wps led). Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48042
*	lantiq: add support for indicating the boot state using three leds	John Crispin	2016-01-01	1	-4/+8
\| \| \| \| \| \| \| \| \| \| \| \| \| \|	The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to indicate the current boot state. This patch adds support for such cases. The existing led sequences should be the same as before. Boards which are using a led different from power (like TDW89x0) are changed to switch of the led after boot Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48041
*	lantiq: define default leds in dts files	John Crispin	2016-01-01	1	-3/+8
\| \| \| \| \| \| \| \| \| \|	- ARV7525PW: use the power led as dsl led as done by the stock firmware - FRITZ3370: use the info led as internet led - FRITZ7320: use the power led as dsl led as done by the stock firmware Signed-off-by: Mathias Kresin <openwrt@kresin.me> SVN-Revision: 48037
*	lantiq: BT Home Hub3A - device tree	John Crispin	2015-01-08	1	-0/+210
	BT Home Hub3A - device tree Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com> SVN-Revision: 43877