| Commit message (Collapse) | Author | Age | Files | Lines |
|
|
|
|
|
| |
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48046
|
|
|
|
|
|
| |
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48045
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The leds of the following boards are not renamed due to lack of
manuals/informations:
- ARV7519PW
- ARV7510PW22
- ARV4510PW
The leds of the ARV4518PWR01* boards are unchanged, since the leds doesn't
match the leds from the manual or pictures (e.g. there shouldn't be a wps led).
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48042
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The BTHOMEHUBV5A has a RGB power led, where every colour is perfect to
indicate the current boot state. This patch adds support for such cases.
The existing led sequences should be the same as before.
Boards which are using a led different from power (like TDW89x0) are
changed to switch of the led after boot
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48041
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
dsl_control (dsl_notify.sh) is the only process which is aware of the
state of the atm/ptm interface. Use the dsl led exclusive for the dsl
line state.
On boards which don't have a distinct internet and a dsl led, let the
netdev status of the atm interface trigger the shared led.
Triggering the shared led according to the status of the ppp interface
isn't suitable, since the led would be switched of if the ppp
connection goes down, but the line is still in sync.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48040
|
|
|
|
|
|
|
|
| |
Use the power leds defined in the dts file instead of hardcoded led names.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48039
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Remove all now double defined leds from the led board file. Use pppoe
as default for all broadband connections, since it's the default in
OpenWrt now.
Rename the the wifi leds to make sure, the not applicable default
values get overwritten.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48038
|
|
|
|
|
|
|
|
| |
The workaround shouldn't be in the default configuration.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 48032
|
|
|
|
|
|
|
|
|
|
| |
- Use common OpenWrt blink patterns instead of custom ones
- Add preinit_regular hook
- Handle the TDW89X0 that does not have a configurable power LED
Signed-off-by: Vittorio Gambaletta <openwrt@vittgam.net>
SVN-Revision: 47914
|
|
|
|
|
|
|
|
|
| |
Replace former uci-defaults.sh implementation with the uci-defaults-new.sh one
and update all users accordingly.
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47867
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
The switch to uci-defaults-new.sh revealed a bug in the former used
uci-defaults.sh, which failed to add leds with colons in the led name.
This bug isn't any longer present in uci-defaults-new.sh and therefore
all via DT defined leds will be added to /etc/config/system with their initial
on/off state, regardless whether they are already added by the board specific
led mappings.
This results for a BTHOMEHUBV5A into the following led configuration:
- soc:blue:power is added as led_power with the initial state "switched on"
- soc:blue:power is added as led_soc_blue_power with the initial state "switched off"
With the final result of a switched off power led after boot.
The only led that needs to be added is the BTHOMEHUBV5A specific dimmed led.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47850
|
|
|
|
|
|
|
|
|
|
|
| |
Starting with r47755 the pppoe wan interface section isn't any longer added to
the network config on firstboot, using the default configuration. Since the
commit message does not mention such a change, I assume that this wasn't
intentionally.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47793
|
|
|
|
|
|
| |
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47785
|
|
|
|
|
|
|
|
|
| |
Now that we have redistributable vdsl/adsl firmware blobs in /lib/firmware,
we can drop the dsl_fw partition and extend the firmware partition.
Signed-off-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 47783
|
|
|
|
|
|
|
|
| |
loading vr9 drivers
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 47764
|
|
|
|
|
|
| |
Signed-off-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47755
|
|
|
|
|
|
|
|
|
|
| |
Whenever two processes were executing different commands at the same
time then one of the commands sometimes got the response of the other
command.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 47213
|
|
|
|
|
|
|
|
|
| |
This patch fixes a wrong non pre-emptive crc errors output of
dsl_control.sh status.
Signed-off-by: Luca Debernardi <luca.debernardi@gmail.com>
SVN-Revision: 47172
|
|
|
|
|
|
|
|
| |
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Reported-by: Jo-Philipp Wich <jow@openwrt.org>
SVN-Revision: 47152
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Fixes ARV7519RW22 flash register (only 1 flash).
Power LED is green, not red.
Rename message LEDs to internet.
Add LEDs configuration (lan, wan, power).
Enable switch VLANs.
Fix secondary USB.
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
Signed-off-by: José Vázquez Fernández <ppvazquezfer@gmail.com>
SVN-Revision: 47132
|
|
|
|
|
|
|
|
|
| |
The device is similar to the TD-W8970, beside a different Atheros 2.4 GHz
wireless chip and the additional, PCI connected, WAVE300 5 GHz wireless.
Signed-off-by: Mathias Kresin <openwrt@kresin.me>
SVN-Revision: 47130
|
|
|
|
|
|
|
| |
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Reported-by: Sylwester Petela <sscapi@gmail.com>
SVN-Revision: 47127
|
|
|
|
|
|
|
|
| |
Meanwhile BTHOMEHUBV5A board was added.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46941
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
As explained in recent sysupgrade/nand.sh commits, current NAND
sysupgrade is a bit misleading because of nand_do_platform_check
behavior. It leaves a special mark in /tmp/sysupgrade-nand-path
triggering some diffent code path in nand_upgrade_stage1.
The plan is to have the check function only check the image and nothing
else. Then platform code (platform_pre_upgrade) should trigger NAND
specific upgrade path. This is what this patch implements.
Please note that because of current nand_upgrade_stage1 implementation
this patch doesn't change any behaior yet. It only prepares lantiq
target for changing nand_do_platform_check (it will be possible after
preparing all other targets as well).
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
SVN-Revision: 46939
|
|
|
|
|
|
|
|
|
| |
Signed-off-by: Florian Eckert <Eckert.Florian@googlemail.com>
Signed-off-by: Helge Mader <hmader@tdt.de>
Tested-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Andre Heider <a.heider@gmail.com>
SVN-Revision: 46917
|
|
|
|
|
|
|
|
| |
lantiq: Add support for Arcadyan ARV8539PW22 (Speedport W 504V)
Signed-off-by: Jannis Pinter <jannis@pinterjann.is>
SVN-Revision: 46224
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
u-boot support depends on the next "upstream" version ([0]) from
Daniel Schwierzeck.
Since the installation process is quite complicated a "how to" was
added to the wiki: [1]
[0] https://github.com/danielschwierzeck/u-boot-lantiq/tree/openwrt/v2014.01-next
[1] http://wiki.openwrt.org/toh/bt/homehub_v5a
V2: Use the correct PCI interrupt (fixes 2.4GHz wifi)
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
SVN-Revision: 46223
|
|
|
|
| |
SVN-Revision: 45897
|
|
|
|
|
|
|
|
| |
Fix failsafe mode for TD-W8970, register interface for preinit.
Signed-off-by: Cezary Jackiewicz <cezary.jackiewicz@gmail.com>
SVN-Revision: 44353
|
|
|
|
|
|
|
|
|
| |
This patch builds on the previous three to streamline support for the
Netgear DGN3500.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44032
|
|
|
|
|
|
|
|
|
| |
Currently this initscript fails if the macaddr has any leading zeroes.
This patch corrects the problem.
Signed-off-by: Daniel Gimpelevich <daniel@gimpelevich.san-francisco.ca.us>
SVN-Revision: 44029
|
|
|
|
|
|
|
|
| |
Add profile and userspace for P2812HNUF1/3, switch from UBI_GLUEBI to UBI_BLOCK
Signed-off-by: Sylwester Petela <sscapi@gmail.com>
SVN-Revision: 43987
|
|
|
|
|
|
|
|
| |
BT Home Hub 3A - userspace
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 43879
|
|
|
|
|
|
|
|
| |
This fixes the adsl led on the Home Hub 2B.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 43876
|
|
|
|
|
|
| |
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 43256
|
|
|
|
|
|
|
|
| |
settings
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 43255
|
|
|
|
|
|
| |
Signed-off-by: Eddi De Pieri <eddi@depieri.net>
SVN-Revision: 43109
|
|
|
|
|
|
|
|
|
|
| |
lantiq_dsl.sh didn't work with VDSL chipsets for now, fix that by
detecting whether vdsl_cpe_control or dsl_cpe_control should be used.
Also add missing quotes around shell string comparision.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
SVN-Revision: 43101
|
|
|
|
| |
SVN-Revision: 42824
|
|
|
|
|
|
|
|
|
|
| |
make the notify script aware of this.
https://dev.openwrt.org/ticket/18005
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42798
|
|
|
|
|
|
|
|
|
|
|
| |
fix inclusion of functions.sh in dsl_fs init script
without this, the following error is seen during build:
./etc/init.d/dsl_fs: line 4: /lib/functions.sh: No such file or directory
Signed-off-by: Thomas Langer <thomas.langer@lantiq.com>
SVN-Revision: 42575
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 42544
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
- use full board name
- rename uboot-env partition
- add dsl_fw partition
- remove unneeded pinmux groups
- move gigabit ethernet to LAN
- load mac address from mtd
Signed-off-by: Álvaro Fernández Rojas <noltari@gmail.com>
SVN-Revision: 42180
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41638
|
|
|
|
|
|
|
|
|
|
|
| |
Run lantiq_board_detect from lantiq_board_name and lantiq_board_model.
This was the one thing missing from r41474 for sysupgrade board
detection to work properly.
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41567
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Enables SysupgradeNAND for BTHOMEHUBV2B.
Depends on the following patches:
http://patchwork.openwrt.org/patch/5817/
http://patchwork.openwrt.org/patch/5848/
http://patchwork.openwrt.org/patch/5851/
Many thanks everyone for your help the last couple of days.
Ben
Signed-off-by: Ben Mulvihill <ben.mulvihill@gmail.com>
SVN-Revision: 41566
|
|
|
|
|
|
| |
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 41472
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
ARGC is a 'C-ism', but not known/valid in shell-syntax - insert the correct
var $# (=number of args) here. under normal conditions this had no impact,
but we should at least correct it. the error was observable like this:
root@box:~ [ -e "/etc/functions.sh" ] && . /etc/functions.sh
root@box:~ [ -e "/lib/functions.sh" ] && . /lib/functions.sh
root@box:~ . /lib/upgrade/platform.sh
root@box:~ . /lib/upgrade/common.sh
root@box:~ platform_check_image /tmp/myfirmware.bin
ash: bad number
root@box:~ echo $?
0
Signed-off-by: Bastian Bittorf <bittorf@bluebottle.com>
SVN-Revision: 40915
|
|
|
|
|
|
|
|
| |
gzipped tarfile
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
SVN-Revision: 40715
|
|
|
|
|
|
|
|
|
|
|
| |
* atm module needs to be loaded before linux-atm
* use absolute firmware paths
* extended validation
* add a script for mounting an optional firmware partition
Signed-off-by: John Crispin <blogic@openwrt.org>
SVN-Revision: 40460
|