aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood/patches-4.4
Commit message (Collapse)AuthorAgeFilesLines
* kirkwood: add ZyXEL NSA325 deviceAlberto Bursi2017-02-111-0/+238
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add ZyXEL NSA325 2-Bay Media Server The ZyXEL NSA325 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1600Mhz - SDRAM memory: 512MB DDR2 400Mhz - Gigabit ethernet: Marvell Alaska - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II ports (internal) - 2 USB 2.0 ports (back) - 1 USB 3.0 port (front) - Fan (fixed speed) - hardware watchdog in a mcu Basically a bigger, more powerful version of NSA310, installation is the same as they share the same flash layout. A notable difference is that there is a hardware watchdog in a mcu on the board, which is disabled by default in the LEDE u-boot. The watchdog is also disabled with a GPIO activation through raw register change when kwbooting or it would reset the board before the new uboot was transferred. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
* kirkwood: add ZyXEL NSA310bAlberto Bursi2017-01-243-10/+226
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kernel: bump to 4.4.40Hauke Mehrtens2017-01-061-5/+5
| | | | | | | Refresh patches on all 4.4 supported platforms. Compile & run tested: lantiq/xrx200 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kirkwood: fix ubi partition nameFelix Fietkau2016-12-303-9/+10
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: refresh patchesLuka Perkov2016-03-141-4/+2
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 49022
* kirkwood: add 4.4 supportLuka Perkov2016-03-1410-0/+1036
Dropped patches because they applied upstream: - 120-iomega_ix2_200.patch - 150-pogoplug_e02.patch Tested on dockstar and goflexnet. Signed-off-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 49019