aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood/image
Commit message (Collapse)AuthorAgeFilesLines
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-2/+2
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* kirkwood: add support for Iomega Storcenter ix2-200Ademar Arvati Filho2018-07-301-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Iomega Storcenter ix2-200 is a dual SATA NAS powered by a Marvell Kirkwood SoC clocked at 1GHz. It has 256MB of RAM and 32MB of flash memory, 3x USB 2.0 and 1x 1Gbit/s NIC Specification: - SoC: Marvell Kirkwood 88F6281 - CPU/Speed: 1000Mhz - Flash-Chip: Hynix NAND - Flash size: 32 MiB,erase size:16 KiB,page size:512,OOB size:16 - RAM: 256MB - LAN: 1x 1000 Mbps Ethernet - WiFi: none - 3x USB 2.0 - UART: for serial console Installation instructions - easy steps: 1. download factory.bin and copy into tftp server 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv setenv serverip 192.168.1.1 setenv ipaddr 192.168.1.13 tftpboot 0x00800000 factory.bin nand erase 0x100000 $(filesize) nand write 0x00800000 0x100000 $(filesize) run bootcmd ``` 3. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Installation steps nand bad blocks proof: 1. download initramfs-uImage and copy into usb ext2 partition ``` mkfs.ext2 -L ext2 /dev/sdh1 mount -t ext2 /dev/sdh1 /mnt cp initramfs-uImage /mnt/initramfs.bin umount /mnt ``` 2. access uboot environment with serial cable and run ``` setenv mainlineLinux yes setenv arcNumber 1682 setenv console 'console=ttyS0,115200n8' setenv mtdparts 'mtdparts=orion_nand:0x100000@0x000000(u-boot)ro,0x20000@0xA0000(u-boot environment)ro,0x300000@0x100000(kernel),0x1C00000@0x400000(ubi)' setenv bootargs_root 'root=' setenv bootcmd 'setenv bootargs ${console} ${mtdparts} ${bootargs_root}; nand read.e 0x800000 0x100000 0x300000; bootm 0x00800000' saveenv usb reset; ext2load usb 0:1 0x00800000 /initramfs.bin; bootm 0x00800000 ``` 3. log into openwrt and sysupgrade to install into flash ``` sysupgrade -n /tmp/sysupgrade.bin ``` 4. access openwrt by dhcp ip address assigned by your router (p.ex: 192.168.1.13) Signed-off-by: Ademar Arvati Filho <arvati@hotmail.com>
* kirkwood: support for buttons in Audi and ViperAlberto Bursi2018-05-151-2/+2
| | | | | | | | | | | | Both these devices have a wps and a reset button on GPIO pins, which need kmod-gpio-button-hotplug package to work. Add this package to their default package config. Troubleshooted and tested on a Viper. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: sort occurrences of boardame alphabeticallyMathias Kresin2018-01-091-59/+59
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: add pogoplug v4Alberto Bursi2018-01-091-0/+7
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | also known as POGO-V4-A3-02 or POGO-V4-A3-01 SoC: Marvell 88F6192 800Mhz SDRAM memory: 128MB Gigabit ethernet: 1 Marvell 88E1310 Flash memory: 128MB 2 status LEDs (one green one red) 1 "Eject" button on the back (used as "Reset" button) 1 USB 2.0 port (on upper side) 1 sata slot (power + data) for 2.5'' drives (upper side) 2 USB 3.0 ports from a controller on PCIe x1 of the SoC 1 full-size SDcard slot (fits a whole SD card into it) This device supports the (linux-only) kwboot tool to send a new uboot over serial console, so it is easy to unbrick in case the uboot is erased and the device won't boot. ----- Install instructions: ----- Since it's not possible to get ssh access to these devices, the only way to take control is to solder pins to get TTL serial access. Case can be opened by removing screws beneath two rubber feet at back of device, then lifting while prying the sides of the upper part out to unhook a latch on each side about 2/3rds of the way toward the front. Serial connection pins are those labeled "J11", left of SD as you face SD opening. Pins are (from left to right, i.e. the first in the list is the nearest to the SD slot) GND, Rx, Tx. Do not connect +V pin if you use a USB (self-powered) TTL-to-USB dongle. Any USB TTL-to-USB converter will work. Baud rate is 115200, parity "none", databits "8", flow control "none". Stock uboot is unable to read ubi partitions (nor usb) so we will replace it first with our uboot. Start a TFTP server at IP address 169.254.254.254, and place the uboot.kwb file in the folder of the server. Start the serial session and then power up the device. As soon as you see text on the serial start pressing random letter keys to stop the boot process. If you see something like the following line you can proceed: CE>> Otherwise if text is still scrolling by you missed the opportunity, pull the plug and try again. write printenv ethaddr The uboot will write something like this: ethaddr=00:50:43:00:02:02 This is the device's MAC address, also present in the sticker under the device. Write this down as we will need to add it in the new uboot configuration. Use the following commands to load the new uboot: tftp 0x20000 u-boot.kwb If the uboot confirms that the transfer was successful, then you can write it to flash with the following commands: nand erase 0 0x200000 nand write 0x20000 0 0x1c0000 if after the last command the uboot wrote "xxxx bytes written: OK" then it was written correctly and we can proceed. If it did not go well, try again or ask assistence in forums. Shutting down or rebooting at this time will brick the device, to unbrick it you will need to use the kwboot tool from a Linux PC or Virtual Machine. Now write: reset and press enter, the device will reboot and you should see again text scrolling by. Press a random key to stop it, and now you should see pogoplugv4> We now add the MAC address back, write: setenv ethaddr '00:50:43:00:02:02' Confirm that the uboot has understood by writing printenv ethaddr If all looks ok, save the setting with saveenv At this point the uboot is configured, and we only need to load the firmware in the flash memory. Follow the steps below in "Firmware recovery procedure". ---- Firmware recovery procedure ---- The new uboot allows easy recovery from a bad firmware upgrade where you can't access the device anymore over ssh or luci. Take a USB flash drive formatted as FAT32, and copy the initramfs image file in it (it will have "initramfs" in the file name), then rename it as "initramfs.bin". Insert the USB drive in the USB 2.0 port of the pogoplug (the port at the top). Power up the device, and wait for it to finish booting. The uboot should find and load the "initramfs.bin" from usb and if you are connected with serial you should see the linux kernel boot log (text scrolling by). Once it is done, press Enter and you will be greeted by the OpenWRT banner. If you were not connected with serial just wait a bit and, you will be able to access it with ssh or luci web interface (once you find its IP). The recovery "initramfs" images are run from RAM, so you will have to do a normal sysupgrade (firmware upgrade) to write a firmware image to flash memory. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: sync image filename with boardnameMathias Kresin2018-01-091-34/+42
| | | | | | | | | | Use <manufacturer>_<modelname> as image name. Use the BOARD_NAME variable to ensure that the former used boardname is still used as the subdirectory name for the sysupgrade-tar image, to not break sysupgrade from earlier versions. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: use the generic board detectMathias Kresin2018-01-091-0/+11
| | | | | | | Drop the target specific detection function in favour of the generic one provided by base-files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: use image metadataMathias Kresin2018-01-091-1/+2
| | | | | | | Append and enforce image metadata. Remove the device specific image checks, they are replaced by image metadata. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: cleanup image build codeMathias Kresin2018-01-091-26/+8
| | | | | | | | | | | | | | Drop NAND_BLOCKSIZE, UBI_OPTS and UBIFS_OPTS. They are either used by not supported filesystems or by the legacy image build code. Add common used options/images to the default build code and override the options where necessary. Don't export the kernel image, it isn't required by any board. While at it, change the file extension for the sysupgrade images to bin. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-1/+11
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kirkwood: add support for Cisco ON100Makoto Takeuchi2017-06-121-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Cisco ON100 device is a Kirkwood based router: SoC: Marvell 88F6282 1600Mhz SDRAM memory: 512MB DDR3 1333Mhz Gigabit ethernet: 2x Marvell 88E1310 (over RGMII) Flash memory: 512MB 2 bi-colour status LEDs (green/red) 1 Reset button 1 USB 2.0 port (on back) 1 SDIO slot (on back) This commit adds a target profile of "Cisco Systems ON100" under the target system "Marvell Kirkwood". Flashing can be performed over tftp, once "dhcp" has been issued: tftpboot ${loadaddr} lede-kirkwood-on100-squashfs-factory.bin nand erase 0x0c0000 ${filesize} nand write ${loadaddr} 0x0c0000 ${filesize} Once flashed, set environment variables to boot: setenv bootcmd nand read \${loadaddr} 0x0c0000 0x540000\; setenv bootargs \; bootm saveenv Signed-off-by: Makoto Takeuchi <mak0@lxsys.co.uk>
* kirkwood: add ZyXEL NSA325 deviceAlberto Bursi2017-02-111-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch add ZyXEL NSA325 2-Bay Media Server The ZyXEL NSA325 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1600Mhz - SDRAM memory: 512MB DDR2 400Mhz - Gigabit ethernet: Marvell Alaska - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II ports (internal) - 2 USB 2.0 ports (back) - 1 USB 3.0 port (front) - Fan (fixed speed) - hardware watchdog in a mcu Basically a bigger, more powerful version of NSA310, installation is the same as they share the same flash layout. A notable difference is that there is a hardware watchdog in a mcu on the board, which is disabled by default in the LEDE u-boot. The watchdog is also disabled with a GPIO activation through raw register change when kwbooting or it would reset the board before the new uboot was transferred. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it> Signed-off-by: Felix Fietkau <nbd@nbd.name> [remove dead code]
* kirkwood: add ZyXEL NSA310bAlberto Bursi2017-01-241-1/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NSA310 device is a Kirkwood based NAS: - SoC: Marvell 88F6702 1200Mhz - SDRAM memory: 256MB DDR2 400Mhz - Gigabit ethernet: Realtek (over pcie) - Flash memory: 128MB - 1 Power button - 1 Power LED (blue) - 5 Status LED (green/red) - 1 Copy/Sync button - 1 Reset button - 2 SATA II port (1 internal and 1 external) - 2 USB 2.0 ports (1 front and 1 back) - Smart fan The stock u-boot cannot read ubi so it should be replaced with the LEDE/OpenWRT's u-boot or with a u-boot from here https://github.com/mibodhi/u-boot-kirkwood This device's boot ROM supports "kwboot" tool (in mainline u-boot, built automatically if CONFIG_KIRKWOOD is declared) that sends an uboot image to the board over serial connection, it is very easy to unbrick. The stock bootloader can use usb and read from FAT filesystems, so the installation process is simple, place the uboot file on a USB flashdrive formatted as FAT (here it is "openwrt-kirkwood-nsa310.bin", then connect TTL to the board and write the following commands in the bootloader console: usb reset fatload usb 0 0x1000000 openwrt-kirkwood-nsa310.bin nand write 0x1000000 0x00000 0x100000 reset Now you are rebooting in the new u-boot, write this in its console to install the firmware: usb reset fatload usb 0 0x2000000 lede-kirkwood-nsa310b-squashfs-factory.bin nand erase.part ubi nand write 0x2000000 ubi 0x600000 If your firmware file is bigger than 6 MiBs you should write its size in hex instead of 0x600000 above, or remove that number entirely (it will take a while in this case). If you are using another uboot that can read ubi, set mtdparts like this mtdparts=mtdparts=orion_nand:0x00c0000(uboot),0x80000(uboot_env),0x7ec0000(ubi) And set your bootcmd to be like this bootcmd=run setenv bootargs; ubi part ubi; ubi read 0x800000 kernel; bootm 0x800000 Then you can install the firmware as described above. After you installed (or configured) the u-boot for booting the firmware, write the device's mac address in the ethaddr u-boot env. The MAC address is usually on a sticker under the device (one of the two codes is the serial), it should begin with "107BEF" as it is assigned to ZyXEL. write in the u-boot console (use your MAC address instead of the example) setenv ethaddr 10:7B:EF:00:00:00 saveenv to save the mac address in the u-boot. Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* kirkwood: only add UBI EOF markers for devices that need itFelix Fietkau2017-01-111-1/+2
| | | | | | Fixes issues where the second-stage u-boot already uses UBI. Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: clean up profiles, move to image makefileFelix Fietkau2016-12-241-8/+11
| | | | | | Adds support for per-device rootfs Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: remove legacy image build codeFelix Fietkau2016-12-241-96/+0
| | | | | | This has been mostly non-functional for a while now Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: convert iconnect, ib62x0 and pogoplug_e02 to the new image build codeFelix Fietkau2016-12-241-4/+19
| | | | | | | Update the correspoding u-boot configs to stop relying on kernel-in-rootfs, which was removed a while back Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: fix uimage creation for some kirkwood devicesbobafetthotmail2016-09-191-1/+0
| | | | | | | | | because with the current system I'm getting fake uImages that are actually a renamed zImage, and that's plain wrong. This fixes bug https://bugs.lede-project.org/index.php?do=details&task_id=131 and https://bugs.lede-project.org/index.php?do=details&task_id=139 Signed-off-by: Alberto Bursi <alberto.bursi@outlook.it>
* image: remove padding parameter from append-kernel/append-rootfsMathias Kresin2016-09-131-2/+2
| | | | | | | | | | | Using pad-to instead of passing the optional padding to append-kernel or append-rootfs. It could be that the value of a variable is passed. In case the variable is empty no error is thrown. Furthermore the purpose of the extra parameter is hard to get without reading the code. Signed-off-by: Mathias Kresin <dev@kresin.me>
* image: add KERNEL_SIZE to the default device varsMathias Kresin2016-09-131-1/+0
| | | | | This reverts commit ec37a565878fd79d4127cbb843c17ce3b8dc97c0 and fixes the underlying issue.
* build: drop UBI EOF marker from images by defaultFelix Fietkau2016-09-121-0/+1
| | | | | | | | Only add them where they are actually required. Should help with compatibility issues with stock U-Boot images that access UBI Signed-off-by: Felix Fietkau <nbd@nbd.name>
* image: use k as unit suffix for blocksizeMathias Kresin2016-09-041-1/+1
| | | | | | | Use k as unit suffix for kilobyte to have a the same unit regardless of the used filesystem. Signed-off-by: Mathias Kresin <dev@kresin.me>
* build: rename sysupgrade-nand to sysupgrade-tarJo-Philipp Wich2016-07-291-1/+1
| | | | | | | Now that the "sysupgrade-nand" step is used by non-NAND targets as well, rename it to "sysupgrade-tar" to make it more generic. Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* image: remove shell calls from legacy ubi/ubifs image codeFelix Fietkau2016-07-251-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: fix UBIFS_OPTS variable in image buildFelix Fietkau2016-07-251-1/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: remove obsolete code for including kernel/dtb in rootfsFelix Fietkau2016-07-201-45/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: remove obsolete ubinize.cfg fileFelix Fietkau2016-07-201-13/+0
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: clean up redundant variables in the image building codeFelix Fietkau2016-07-201-15/+9
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: get rid of useless ubifs/ubi option variablesFelix Fietkau2016-07-201-33/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* image.mk: clean up redundant code related to DEVICE_DTSFelix Fietkau2016-07-151-2/+1
| | | | | | | | It is used by a core build template, so the variable should be initialized and added to DEVICE_VARS in the core. Same for DEVICE_DTS_DIR Signed-off-by: Felix Fietkau <nbd@nbd.name>
* image: clean up UBI related device variable definitionsFelix Fietkau2016-07-141-1/+1
| | | | | | | Move UBI related variable export to core, since the variables are used by a core Build/ template Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kernel: Move append-dtb to common image-commandsBen Whitten2016-06-221-4/+0
| | | | | | This build step is used by various targets, move it to a common section. Signed-off-by: Ben Whitten <ben.whitten@gmail.com>
* kirkwood: install kernel binaries into bin/ for use with external storageFelix Fietkau2016-06-071-0/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: move ubi/ubifs options to the image makefileFelix Fietkau2016-05-191-0/+36
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* linux/kirkwood: migrate goflexhome/goflexnet to new ubi styleLuka Perkov2016-03-141-7/+13
| | | | | | | | Also using the new image build step format Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 49013
* kirkwood/dockstar: use ubi(kernel, squashfs, ubifs) imagesLuka Perkov2016-03-141-4/+1
| | | | | | | | | | | | | | | | | | | The new image requires `bootz` because of devicetree appending. To flash a new image boot initramfs: tftpboot 0x800000 openwrt-kirkwood-dockstar-initramfs-kernel.bin bootz 0x800000 # detach if already attached ubidetach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}') # scp openwrt-kirkwood-dockstar-squashfs-factory.bin /tmp ubiformat -f /tmp/openwrt-kirkwood-dockstar-squashfs-factory.bin # attach is important to resize rootfs_data otherwise it wont boot ubiattach -p /dev/$(grep ubi /proc/mtd|awk -F: '{print $1}') Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 49010
* kirkwood: add DEVICE_VAR KERNEL_IN_UBI for kernel as volume in ubi imagesLuka Perkov2016-03-141-1/+16
| | | | | | | | depending on KERNEL_IN_UBI, the image.mk will create a ubi volume for the kernel Signed-off-by: Alexander Couzens <lynxis@fe80.eu> SVN-Revision: 49009
* targets: add kernel image dependencies on device tree filesFelix Fietkau2016-01-061-0/+1
| | | | | | Signed-off-by: Felix Fietkau <nbd@openwrt.org> SVN-Revision: 48146
* kirkwood: add Linksys routers to default profileLuka Perkov2015-11-111-2/+2
| | | | | | Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47458
* kirkwood: rename EA3500/EA4500 profilesLuka Perkov2015-11-101-2/+2
| | | | | | | | Match the engineering board names now used elsewhere. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47436
* kirkwood: generate factory images for Linksys EA[34]500Luka Perkov2015-11-101-6/+39
| | | | | | | | | This is done with the new image generation system and board names. It also generates a sysupgrade.tar image. Signed-off-by: Claudio Leite <leitec@staticky.com> SVN-Revision: 47432
* kirkwood: add initial support for NSA310sLuka Perkov2015-11-011-0/+3
| | | | | | | Signed-off-by: Tony Dinh <mibodhi@gmail.com> Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 47330
* kirkwood: image: Remove custom mkfs targz override as base should be fine nowFelix Fietkau2015-10-311-5/+0
| | | | | | | | | It was wrong anyway, missing file sort order parameter which was fixed in base month ago. Signed-off-by: Petr Štetiar <ynezz@true.cz> SVN-Revision: 47313
* kirkwood: image: Refactor sanitize_profile_name using PROFILE_SANITIZED varFelix Fietkau2015-10-311-18/+14
| | | | | | Signed-off-by: Petr Štetiar <ynezz@true.cz> SVN-Revision: 47309
* image: fix jffs2(_nand) image generationJonas Gorski2015-08-051-2/+3
| | | | | | | | | | | | Variables dependend on JFFS2_BLOCKSIZE and NANDBLOCK_SIZE are used for template generation, so need to be present before inclusion of image.mk in target image Makefiles. So move all declarations to before any includes. Fixes: r42878 ("image.mk: clean up and parallelize mkfs calls") Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46564
* kirkwood: add support for the Seagate GoflexHomeLuka Perkov2015-05-081-0/+3
| | | | | | | | Add Support for the Seagate GoflexHome <http://wiki.openwrt.org/toh/seagate/goflexhome> Signed-off-by: L. D. Pinney <ldpinney@gmail.com> SVN-Revision: 45647
* kirkwood: add sheevaplug and derivativesLuka Perkov2014-12-171-0/+12
| | | | | | | | | | | | Add kirkwood FDT: - SheevaPlug - SheevaPlug with eSATA - GuruplugServerPlus - Topkick1281P2 Signed-off-by: Gérald Kerma <drEagle@doukki.net> SVN-Revision: 43735
* kirkwood: sort 110-nas profileLuka Perkov2014-12-111-3/+3
| | | | | | Signed-off-by: Luka Perkov <luka@openwrt.org> SVN-Revision: 43642
* kirkwood: Add support for Iomega StorCenter ix2-200John Crispin2014-11-261-0/+3
| | | | | | Signed-off-by: Richard Kunze <richard.kunze@web.de> SVN-Revision: 43391
* kirkwood: add support for Linksys EA3500Luka Perkov2014-11-101-0/+3
| | | | | | | | http://wiki.openwrt.org/toh/linksys/ea3500 Signed-off-by: Dan Walters <dan@walters.io> SVN-Revision: 43230
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-07 02:30:00 +0000