aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/kirkwood/config-5.4
Commit message (Collapse)AuthorAgeFilesLines
* kirkwood: refresh kernel configSungbo Eo2021-02-051-63/+2
| | | | | | Refresh config with make kernel_oldconfig. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-221-3/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-061-1/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* kirkwood: add support for Check Point L-50Pawel Dembicki2020-07-111-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Check Point L-50 from 600/1100 series routers. Specification: -CPU: Marvell Kirkwood 88F6281 1200MHz -RAM: 512MB -Flash: NAND 512MB -WiFi: mPCIe card based on Atheros AR9287 b/g/n -WAN: 1 Gigabit Port (Marvell 88E1116R PHY) -LAN: 9 Gigabit Ports (2x Marvell 88E6171(5+4)) -USB: 2x USB2.0 -Express card slot -SD card slot -Serial console: RJ-45 115200 8n1 -Unsupported DSL Known issues: -DSL not supported -Expresscard not tested Installation: Step one -> backup: make backup u-boot and env for revert stock posibility make backup dsl_mac_addr, dmz_mac_addr, eth1addr, ethaddr and all lanX_mac_addr Step two -> Use kwboot tool to upload openwrt u-boot to RAM: run kwboot: "kwboot -B 115200 /dev/ttyUSB0 -b u-boot.kwb -p -t" end start u-boot Step three -> Restore macs (e.g. below): setenv eth1addr 00:1C:XX:XX:XX:6C setenv ethaddr 00:1C:XX:XX:XX:6B setenv lan1_mac_addr 00:1C:XX:XX:XX:6C setenv lan2_mac_addr 00:1C:XX:XX:XX:6D setenv lan3_mac_addr 00:1C:XX:XX:XX:6E setenv lan4_mac_addr 00:1C:XX:XX:XX:6F setenv lan5_mac_addr 00:1C:XX:XX:XX:70 setenv lan6_mac_addr 00:1C:XX:XX:XX:71 setenv lan7_mac_addr 00:1C:XX:XX:XX:72 setenv lan8_mac_addr 00:1C:XX:XX:XX:73 setenv dmz_mac_addr 00:1C:XX:XX:XX:74 setenv dsl_mac_addr 00:1C:XX:XX:XX:75 Step four -> flash u-boot: mw 0x0800000 0xffff 0x100000 nand erase 0x0 100000 tftp 0x0800000 openwrt-kirkwood-l50-u-boot.kwb nand write 0x0800000 0x0 0x100000 saveenv Step five -> run initramfs image: tftpboot 0x02000000 openwrt.bin; bootm 0x02000000; Step six -> install sysupgrade OpenWrt image: copy to /tmp/ sysupgrade image run sysupgrade Back to stock: Restore original u-boot end env. Install factory image via stock u-boot. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: add support for Zyxel NSA310SPawel Dembicki2020-07-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Zyxel NSA310S is a NAS based on Marvell kirkwood SoC. Specification: - Processor Marvell 88F6702 1 GHz - 256MB RAM - 128MB NAND - 1x GBE LAN port (PHY: Marvell 88E1318) - 2x USB 2.0 - 1x SATA - 3x button - 7x leds - serial on J1 connector (115200 8N1) (GND-NOPIN-RX-TX-VCC) Known issues: - no kernel module for RTC. [*] - buzzer (connected to MPP43) need to be drived by 1kHz signal - no kernel module for internal MCU connected via I2C[**] [*] Karoly Pocsi made simple, unofficial driver for HT1382. It can be found here: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ [**] Karoly Pocsi found how CPU talk with MCU: It is possible to query the MCU-controlled fan speed and temperature: i2cget -y 0x0 0x0a 0x07 i2cget -y 0x0 0x0a 0x08 The first value (0x07) is the temperature in ° C, the second (0x08) is the time in milliseconds to complete one fan revolution (rpm = 60,000 / value). Info translated from: https://www.madadmin.com/zyxel-nsa320s-es-debian-linux-4-resz/ Installation: TFTP: 1. Run serial console and go to u-boot. 2. Copy u-boot via tftp and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftp 0x0800000 nsa310s-u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 3. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 4. Copy and run initramfs image => setenv ipaddr 192.168.1.2 => setenv serverip 192.168.1.4 => tftpboot zyxel_nsa310s-initramfs-uImage => bootm 0x800000 5. Download sysupgrade image and perform sysupgrade USB: 1. Prepare usb fat32 drive with u-boot.kwb and initramfs image. Stick it to USB 2.0 port. 2. Run serial console and go to u-boot. 3. Copy u-boot from usb and write to NAND: => mw 0x0800000 0xffff 0x100000 => nand erase 0x0 100000 => usb start => fatload usb 0 0x0800000 u-boot.kwb => nand write 0x0800000 0x0 0x100000 => reset 4. Run new u-Boot, repair bootcmd and restore MAC address from sticker => setenv ethaddr AA:BB:CC:DD:EE:FF => saveenv 5. Copy and run initramfs image: => usb start => fatload usb 0 0x0800000 initramfs-uImage => bootm 0x800000 6. Download sysupgrade image and perform sysupgrade. Based on work ThBexx <thomas.beckler@hotmail.com> DTS based on dropped support in 0ebdf0c. Tested-by: Lech Perczak <lech.perczak@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [NSA310s -> NSA310S in DEVICE_MODEL] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kirkwood: refresh kernel configPawel Dembicki2020-06-141-9/+4
| | | | | | | | It was made by running "make kernel_oldconfig". Suggested-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move ext4 support to modulesPawel Dembicki2020-06-141-2/+0
| | | | | | | | | | | | Ext4 support is built in kirkwood kernel. This patch moves ext4 support to modules and enables it for devices with SATA interface. Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [rebase] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move usb support to modulesPawel Dembicki2020-06-141-5/+0
| | | | | | | | | | | | | | | USB support built in kernel isn't required for booting. This patch move USB support to modules. CONFIG_USB_STORAGE is removed because it can be found in kmod-usb-storage and all usb support for this targed is moved to kmods. Tested-by: Cezary Jackiewicz <cezary@eko.one.pl> [nsa310] Tested-by: Alberto Bursi <bobafetthotmail@gmail.com> [nsa325, ea4500] Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [keep CONFIG_SCSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kirkwood: move mmc/sd features to modulesPawel Dembicki2020-06-141-3/+0
| | | | | | | | | | All devices are using nand images. Built-in MMC/SD modules are not needed anymore. Run tested: pogo v4 Reviewed-by: Sungbo Eo <mans0n@gorani.run> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: move sata features to modulesPawel Dembicki2020-06-141-1/+0
| | | | | | | | | | All devices are using nand images. Built-in SATA modules are not needed anymore. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [only move CONFIG_SATA_MV] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: Pawel Dembicki <paweldembicki@gmail.com> [pogo v4]
* kirkwood: switch from swconfig to dsaPawel Dembicki2020-04-281-2/+9
| | | | | | | | | | | | | | | | | | | | | | This patch removes support for swconfig and switches to dsa driver. swconfig and switch drivers are removed. DSA driver is enabled and configuration is adjusted. In kirkwood only two devices have switches: Linksys EA3500 and EA4500. WAN MAC configuration in 02_network is required because otherwise WAN would have the same MAC address as lan interfaces. In swconfig solution the WAN address was assigned in u-Boot to eth1. Now, as eth1 is disabled and wan is part of the switch, we have to set it manually. Compile tested: EA3500, EA4500 Run tested: EA4500 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [minor commit title/message adjustments, remove swconfig package for devices] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move TEO governor to generic configTomasz Maciej Nowak2020-03-171-1/+0
| | | | | | | | This new symbol popped up in few places. Disable it in generic config. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed merge conflict in generic/config-5.4] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: 5.4: remove some dup config options already set in genericYousong Zhou2020-03-101-6/+0
| | | | | | | This furthers 860652f4b9da ("kernel: 5.4: move some kconfig options to generic") Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kirkwood: initial refresh 5.4 configPawel Dembicki2020-03-031-16/+38
| | | | | | Refreshed kernel config with updated NAND config. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* kirkwood: copy files and config from 4.19 to 5.4Pawel Dembicki2020-03-031-0/+344
This commit is simple copy config, files and patches from 4.19 to 5.4 kernel. No changes was done. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>