aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq807x/base-files/etc/board.d/02_network
Commit message (Collapse)AuthorAgeFilesLines
* ipq807x: Add ZyXEL NBG7815André Valentin2023-01-191-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZyXEL NBG7815 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1 GB 2x Nanya NT5CC256M16ER-EK * Storage: * 8MB serial flash Winbond W25Q64DW * 4GB eMMC flash Kingston EMMC04G-M627 * Ethernet: * 4x1G RJ45 ports (QCA8074A) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * 1x10G RJ45 port (AQR113C) with 1x status LED * Switch: Qualcomm Atheros QCA8075 * WLAN: * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 2x 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate * Bluetooth CSR8811 using HSUART, currently unsupported * USB: 1x USB3.0 Type-A port * LED-s currently not supported: * White * Dark Blu * Amber * Purple * Purple and dark blue * Red * Buttons: * 1x Soft reset * Power: 12V DC Jack Installation instructions: * Disconnect WAN * Reset device to factory defaults by pushing reset button 15 sec, LEDs should lit orange color. * After 5-10 minutes, when the LEDs turn constant dark blue, put your LAN cable and connect at address 192.168.123.1 by telnet on port 23 * Login with NBG7815 login: root password: nbg7815@2019 * cd /tmp/ApplicationData * wget -O openwrt-ipq807x-generic-zyxel_nbg7815-squashfs-sysupgrade.bin http://... * wget https://github.com/itorK/nbg7815_tools/blob/main/flash_to_openwrt.sh * run flash_to_openwrt.sh If you can't use wget, you can transfer the files via nc. See https://openwrt.org/inbox/toh/zyxel/nbg7815_armor_g5 for installation details. Bluetooth usage: * you need at least package bluez-utils, recommended bluez-daemon * run following commands to enable and start hciattach /dev/ttyMSM1 bcsp hciconfig hci0 up Many thanks to itorK for his work on this device: https://github.com/itorK/openwrt/tree/nbg7815 Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq807x: add Dynalink DL-WRX36Dirk Buchwalder2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Dynalink DL-WRX36 is a AX WIFI router with 4 1G and 1 2.5G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 256MB Nand • Ethernet: 4x 1G RJ45 ports (QCA8075) + 1 2.5G Port (QCA8081) • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 802.11a/b/g/n/ac/ax 2402 PHY rate • 1x USB 3.0 • 1 gpio-controlled dual color led (blue/red) • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard (J1004) the connector size is a 4-pin 2.0 mm JST PH. RX/TX is working, u-boot bootwait is active, secure boot is enabled. Notes: - Serial is completely deactivated in the stock firmware image. - This commit adds only single partition support, that means sysupgrade is upgrading the current rootfs partition. - Installation can be done by serial connection or SSH access on OEM firmware Installation Instructions: Most part of the installation is performed from an initramfs image running OpenWrt, and there are two options to boot it. Boot initramfs option 1: Using serial connection (3.3V) 1. Stop auto boot to get to U-boot shell 2. Transfer initramfs image to device (openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb) Tested using TFTP and a FAT-formatted USB flash drive. 3. Boot the initramfs image # bootm Boot initramfs option 2: From SSH access on OEM firmware 1. Copy the initramfs image to a FAT-formatted flash drive (tested on single-partition drive) and connect it to device USB port. 2. Change boot command so it loads the initramfs image on next boot Fallback to OEM firmware is provided. # fw_setenv bootcmd 'usb start && fatload usb 0:1 0x44000000 openwrt-ipq807x-generic-dynalink_dl-wrx36-initramfs-uImage.itb && bootm 0x44000000; bootipq' 3. Reboot the device to boot the initramfs # reboot Install OpenWrt from initramfs image: 1. Use SCP (or other way) to transfer OpenWrt factory image 2. Connect to device using SSH (on a LAN port) 3. Check MTD partition table. rootfs and rootfs_1 should be mtd18 and mtd20 depending on current OEM slot. # cat /proc/mtd 4. Do a ubiformat to both rootfs partitions: # ubiformat /dev/mtd18 -y -f /path_to/factory_image # ubiformat /dev/mtd20 -y -f /path_to/factory_image 5. Set U-boot env variable: mtdids # fw_setenv mtdids 'nand0=nand0' 6. Get offset of mtd18 to determine current OEM slot - If current OEM slot is 1, offset is 16777216 (0x1000000) - If current OEM slot is 2, offset is 127926272 (0x7a00000) # cat /sys/class/mtd/mtd18/offset 7. Set U-boot env variable: mtdparts If current OEM slot is 1, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x1000000(fs),0x6100000@0x7a00000(fs_1)' If current OEM slot is 2, run: # fw_setenv mtdparts 'mtdparts=nand0:0x6100000@0x7a00000(fs),0x6100000@0x1000000(fs_1)' 8. Set U-boot env variable: bootcmd # fw_setenv bootcmd 'setenv bootargs console=ttyMSM0,115200n8 ubi.mtd=rootfs rootfstype=squashfs rootwait; ubi part fs; ubi read 0x44000000 kernel; bootm 0x44000000#config@rt5010w-d350-rev0' 9. Reboot the device # reboot Note: this PR adds only single partition support, that means sysupgrade is upgrading the current rootfs partition Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Edgecore EAP102Matthew Hagan2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq807x: Add Xiaomi AX9000Robert Marko2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Xiaomi AX9000 is a premium 802.11ax "tri"-band router/AP. Specifications: * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 1024MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: * 4x1G RJ45 ports (QCA8075) with 1x status LED per port * 1x2.5G RJ45 port (QCA8081) with 1x status LED * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 4x4@40MHz 802.11b/g/n/ax 1147 Mbps PHY rate * 5.8GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402Mbps PHY rate * 5GHz: PCI based Qualcomm QCN9024 4x4@160MHz 802.11a/b/g/n/ac/ax 4804Mbps PHY rate * USB: 1x USB3.0 Type-A port * LED-s: * System (Blue and Yellow) * Network (Blue and Yellow) * RGB light bar on top in X shape * Buttons: * 1x Power switch * 1x Soft reset * 1x Mesh button * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/ax9000#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd21 and mtd22 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd22 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd21 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax9000-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq807x: add QNAP 301wDirk Buchwalder2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Edimax CAX1800Dirk Buchwalder2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Edimax CAX1800 is a 802.11 ax dual-band AP with PoE. AP can be ceiling or wall mount. Specifications: • CPU: Qualcomm IPQ8070A Quad core Cortex-A53 1.4GHz • RAM: 512MB of DDR3 • Storage: 128MB NAND (contains rootfs) / 8MB NOR (contains art and uboot-env) • Ethernet: 1x 1G RJ45 port (QCA8072) PoE • WLAN: 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate 5GHz: Qualcomm QCN5054 2x2 802.11a/b/g/n/ac/ax 1201 PHY rate • LEDs: 3 x GPIO-controlled System-LEDs (form one virtual RGB System-LED) black_small_square Buttons: 1x soft reset black_small_square Power: 12V DC jack or PoE (802.3af ) An unpopulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, but it drops only to a limited shell . Installation Instructions: black_small_square obtain serial access black_small_square stop auto boot black_small_square tftpboot the initramfs image (serverip is set to 192.168.99.8 in uboot) black_small_square bootm black_small_square copy openwrt-ipq807x-generic-edimax_cax1800-squashfs-nand-factory.ubi to the device black_small_square write the image to the NAND: black_small_square cat /proc/mtd and look for rootfs partition (should be mtd0) black_small_square ubiformat /dev/mtd0 -f -y openwrt-ipq807x-generic-edimax_cax1800-squashfs- nand-factory.ubi black_small_square reboot Note: Device is not using dual partitioning (NAND contains other partitions with different manufacture data etc.) Draytek VigorAP 960C and Lancom LW-600 both look similar, but I haven't checked them. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Redmi AX6Zhijun You2023-01-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
* ipq807x: add Xiaomi AX3600Robert Marko2023-01-161-0/+28
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-26 02:31:58 +0000