aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq807x/base-files/etc/board.d/01_leds
Commit message (Collapse)AuthorAgeFilesLines
* ipq807x: add support for Netgear WAX218Alexandru Gagniuc2023-03-201-0/+5
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Netgear WAX218 is a 802.11ax AP claiming AX3600 support. It is wall or ceiling mountable. It can be powered via PoE, or a 12 V adapter. The board has footprints for 2.54mm UART headers. They're difficult to solder because the GND is connected to a large copper plane. Only try soldering if you are very skilled. Otherwise, use pogo pins. Specifications: --------------- * CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz * RAM: 366 MB of RAM available to OS, not sure of total amount * Storage: Macronix MX30UF2G18AC 256MB NAND * Ethernet: * 2.5G RJ45 port (QCA8081) with PoE input * WLAN: * 2.4GHz/5GHz with 8 antennas * LEDs: * Power (Amber) * LAN (Blue) * 2G WLAN (Blue) * 5G WLAN (Blue) * Buttons: * 1x Factory reset * Power: 12V DC Jack * UART: Two 4-pin unpopulated headers near the LEDs * "J2 UART" is the CPU UART, 3.3 V level Installation: ============= Web UI method ------------- Flashing OpenWRT using the vendor's Web UI is problematic on this device. The u-boot mechanism for communicating the active rootfs is antiquated and unreliable. Instead of setting the kernel commandline, it relies on patching the DTS partitions of the nand node. The way partitions are patched is incompatible with newer kernels. Newer kernels use the SMEM partition table, which puts "rootfs" on mtd12. The vendor's Web UI will flash to either mtd12 or mtd14. One reliable way to boot from mtd14 and avoid boot loops is to use an initramfs image. 1. In the factory web UI, navigate to System Manager -> Firmware. 2. In the "Local Firmware Upgrade" section, click Browse 3. Navigate and select the 'web-ui-factory.fit' image 4. Click "Upload" 5. On the following page, click on "Proceed" The flash proceeds at this point and the system will reboot automatically to OpenWRT. 6. Flash the 'nand-sysupgrade.bin' using Luci or the commandline SSH method ---------- Enable SSH using the CLI or Web UI. The root account is locked out to ssh, and the admin account defaults to Netgear's CLI application. So we need to get creative: First, make sure the device boots from the second firmware partition: ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 1 Then reboot the device, and run the update: scp -O -o kexalgorithms=diffie-hellman-group14-sha1 \ -o hostkeyalgorithms=ssh-rsa \ netgear_wax218-squashfs-nand-factory.ubi \ admin@<ipaddr>:/tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/ubiformat /dev/mtd12 -f /tmp/openwrt.ubi ssh -okexalgorithms=diffie-hellman-group14-sha1 admin@<ipaddr> \ /usr/sbin/fw_setenv active_fw 0 Now reboot the device, and it should boot into a ready-to-use OpenWRT. Signed-off-by: Alexandru Gagniuc <mr.nuke.me@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Francisco G Luna <frangonlun@gmail.com>
* ipq807x: add Edgecore EAP102Matthew Hagan2023-01-161-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Edgecore EAP102 is a wall/ceiling mountable AP. The AP can be powered by either PoE or AC adapter. Device info: - IPQ8071-A SoC - 1GiB RAM - 256MiB NAND flash - 32MiB SPI NOR - 2 Ethernet ports - 1 Console port - 2GHz/5GHz AX WLAN - 2 USB 2.0 ports Install instructions: Prerequistes - TFTP server, preferrably within 192.168.1.0/24 Console cable plugged in (115200 8N1 no flow control) 1. Power on device and interrupt u-boot to obtain u-boot CLI 2. set serverip to IP address of the TFTP server: `setenv serverip 192.168.1.250` 3. Download image from TFTP server: `tftpboot 0x44000000 openwrt-ipq807x-generic-edgecore_eap102-squashfs-nand-factory.ubi` 4. Flash ubi image to both partitions and reset: `sf probe imxtract 0x44000000 ubi nand device 0 nand erase 0x0 0x3400000 nand erase 0x3c00000 0x3400000 nand write $fileaddr 0x0 $filesize nand write $fileaddr 0x3c00000 $filesize reset` Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq807x: add QNAP 301wDirk Buchwalder2023-01-161-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | QNAP 301w is a AX WIFI router with 4 1G and 2 10G ports. Specifications: • CPU: Qualcomm IPQ8072A Quad core Cortex-A53 2.2GHz • RAM: 1024MB of DDR3 • Storage: 4GB eMMC (contains kernel and rootfs) / 8MB NOR (contains art and u-boot-env) • Ethernet: 4x 1G RJ45 ports + 2 10G ports (Aquantia AQR113C) • WLAN: 2.4GHz: Qualcomm QCN5024 4x4 (40 MHz) 802.11b/g/n/ax 1174 Mbps PHY rate 5GHz: Qualcomm QCN5054 4x4 (80 MHz) or 2x2 (160 MHz) 802.11a/b/g/n/ac/ax 2402 PHY rate • LEDs: 7 x GPIO-controlled dual color LEDs + 2 GPIO-controlled single color LEDs • Buttons: 1x soft reset / 1x WPS • Power: 12V DC jack A poulated serial header is onboard. RX/TX is working, bootwait is active, secure boot is not enabled. SSH can be activated in the stock firmware, hold WPS button til the second beep (yes the router has a buzzer) SSH is available on port 22200, login with user admin and password "mac address of the router". Installation Instructions: • obtain serial access (https://openwrt.org/inbox/toh/qnap/301w#serial) • stop auto boot • setenv serverip 192.168.10.1 • setenv ipaddr 192.168.10.10 • tftpboot the initramfs image (openwrt-ipq807x-generic-qnap_301w-initramfs-fit-uImage.itb) • bootm • make sure that current_entry is set to "0": "fw_printenv -n current_entry" should be print "0". If not, do "fw_setenv current_entry 0" • copy openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin to the device to /tmp folder • sysupgrade -n /tmp/openwrt-ipq807x-generic-qnap_301w-squashfs-sysupgrade.bin this flashes openwrt to the first kernel and rootfs partition (mmcblk0p1 / mmcblk0p4) • reboot Note: this leaves the second kernel / rootfs parition untouched. So if you want to go back to stock, stop u-boot autoboot, "setenv current_entry 1" , "saveenv", "bootipq". Stock firmware should start from the second partition. Then do a firmwareupgrade in the stock gui, that should overwrite the openwrt in the first partitions Make 10G Aquantia phy's work: The aquantia phy's need a firmware to work. This can either be loaded in linux with a userspace tool or in u-boot. I was not successfull to load the firmware in linux (aq-fw-download) but luckily there is aq_load_fw available in u-boot. But first the right firmware needs to write to the 0:ETHPHYFW mtd partition (it is empty on my device) Grab the ethphy firmware image from: https://github.com/kirdesde/nbg7815_gpl/blob/master/target/linux/ipq/ipq807x_64/prebuilt_images/AQR_ethphyfw.mbn and scp that to openwrt. Check the 0:ETHPHYFW partition number: cat /proc/mtd|grep "0:ETHPHYFW", should be mtd10. Backup the 0:ETHPHYFW partition: dd if=/dev/mtd10 of=/tmp/ethphyfw.backup, scp ethphyfw.backup to a save place. Write the new firmware image to the 0:ETHPHYFW partition: "mtd erase /dev/mtd10", "mtd -n write AQR_ethphyfw.mbn /dev/mtd10". Reboot to u-boot. Check if aq_load_fw is working: "aq_load_fw 0", that checks the firmware and if successfull, loads iram and dram to one of the aquantia phy's. If that worked, add the aq_load_fw to the bootcmd: setenv bootcmd "aq_load_fw 0 && aq_load_fw 8 && bootipq" "saveenv" "reset" Board reboots and the firmware load to both phy's should start and then openwrt boots. Check if the 10G ports work. Note: lan port labeled "10G-2" is configured as WAN port as per default. All other port are in the br-lan. This can be changed in the network config. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de>
* ipq807x: add Redmi AX6Zhijun You2023-01-161-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Redmi AX6 is a budget 802.11ax dual-band router/AP Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 128MB NAND * Ethernet: 4x1G RJ45 ports (QCA8075) * WLAN: * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LEDs: * System (Blue/Yellow) * Network (Blue/Yellow) *Buttons: 1x soft reset *Power: 12V DC jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_redmi_ax6_ax3000#ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-redmi_ax6-initramfs-factory.ubi && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-redmi_ax6-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Zhijun You <hujy652@gmail.com>
* ipq807x: add Xiaomi AX3600Robert Marko2023-01-161-0/+16
Xiaomi AX3600 is a budget 802.11ax dual-band router/AP. Specifications: * CPU: Qualcomm IPQ8071A Quad core Cortex-A53 1.4GHz * RAM: 512MB of DDR3 * Storage: 256MB of parallel NAND * Ethernet: 4x1G RJ45 ports (QCA8075) with 1x status LED per port * WLAN: * PCI based Qualcomm QCA9889 1x1 802.11ac Wawe 2 for IoT * 2.4GHz: Qualcomm QCN5024 2x2 802.11b/g/n/ax 574 Mbps PHY rate * 5GHz: Qualcomm QCN5054 4x4@80MHz or 2x2@160MHz 802.11a/b/g/n/ac/ax 2402 PHY rate * LED-s: * System (Blue and Yellow) * IoT (Blue) * Network (Blue and Yellow) * Buttons: 1x Soft reset * Power: 12V DC Jack Installation instructions: Obtaining SSH access is mandatory https://openwrt.org/inbox/toh/xiaomi/xiaomi_ax3600#obtain_ssh_access Installation is done by the ubiformat method, through SSH: 1. Open an SSH shell to the router 2. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi to the /tmp directory 3. Check which rootfs partition is your router booted in (0 = rootfs | 1 = rootfs_1): nvram get flag_boot_rootfs 4. Find the rootfs and rootfs_1 mtd indexes respectively: cat /proc/mtd Please confirm if mtd12 and mtd13 are the correct indexes from above! 5. Use the command ubiformat to flash the opposite mtd with UBI image: If nvram get flag_boot_rootfs returned 0: ubiformat /dev/mtd13 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=1 && nvram set flag_last_success=1 && nvram commit otherwise: ubiformat /dev/mtd12 -y -f /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-initramfs-factory.ubi -s 2048 -O 2048 && nvram set flag_boot_rootfs=0 && nvram set flag_last_success=0 && nvram commit 6. Reboot the device by: reboot Previous commands flashed an ubinized OpenWrt initramfs that will serve as the intermediate step since OpenWrt uses unified rootfs in order to fully utilize NAND and provide enough space for packages. Continue in order to pernamently flash OpenWrt: 7. SSH into OpenWrt from one of the LAN ports 8. Copy the file openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin to the /tmp directory 9. Sysupgrade the device: sysupgrade -n /tmp/openwrt-ipq807x-generic-xiaomi_ax3600-squashfs-sysupgrade.bin Device will reboot with OpenWrt, and then sysupgrade can be used to upgrade the device when desired. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-10 15:41:57 +0000