aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 5.10 to 5.10.111John Audia2022-04-171-1/+1
| | | | | | | | | | | | | | | Removed upstreamed: pending-5.10/850-0003-PCI-aardvark-Fix-support-for-MSI-interrupts.patch apm821xx/patches-5.10/150-ata-sata_dwc_460ex-Fix-crash-due-to-OOB-write.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us> (cherry picked from commit 0085dd6cb5e3c57dd22994c22ce893575711b6f7)
* ipq806x: fix wrong CPU OPP for ipq8062Ansuel Smith2022-04-171-16/+16
| | | | | | | | | | Fix wrong CPU OPP for ipq8062. Revision of the SoC added an extra 25mV for every pvs. Also fix the voltage min/max value that were wrong. Reviewed-by: Robert Marko robimarko@gmail.com Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> (cherry picked from commit 3f0d87fd69b13f7d1fa06bdcc951a2896a0a9360)
* ipq806x: fix USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-171-14/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The existing device tree has incorrect definitions for usb3_0 and usb3_1 and the blocks they depend upon: their addresses and interrupts are swapped. However, their clocks and resets are not. The result is that the USB blocks are non-functional if only one of them is enabled. This fix backports the definitions from mainline Linux 5.15 to OpenWrt's 5.10 dtsi additions. See the relevant mainline code here: https://github.com/torvalds/linux/blob/v5.17/arch/arm/boot/dts/qcom-ipq8064.dtsi#L1062-L1148 This fix does not break existing ports. But some ports may have enabled both USB blocks even thought their board only implements one, because enabling a single USB block would not have worked before this fix. This means that revisiting all ports of ipq806x devices that implement a single USB port is advised. This work must be done by maintainers that can determine which USB block corresponds to the implemented port on their hardware. Note that this fix swaps the names of the hardware ports. This is unfortunate, but will happen anyway when switching to kernel 5.15. Thus, it is best to do this ASAP, before users get to depend on port names. It is strongly recommended that this fix is backported to 22.03 before its release. This will minimize the number of users affected by the port name swap. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> (cherry picked from commit 284f2c2ae0e569660effa61c9f8d0f6459a2ae19)
* ipq806x: remove non-working fixes for USB bug in 5.10 dtsi additionsRodrigo Balerdi2022-04-172-4/+0
| | | | | | | These workarrounds are incomplete and non-functional, and thus not needed. Signed-off-by: Rodrigo Balerdi <lanchon@gmail.com> (cherry picked from commit 3a4d972d43987e1ab0f697817c0f68d1a4a706dc)
* kernel: bump 5.10 to 5.10.110John Audia2022-04-101-1/+1
| | | | | | | | | | | | | | | | | | | Removed upstreamed: generic/backport-5.10/350-v5.18-MIPS-pgalloc-fix-memory-leak-caused-by-pgd_free.patch generic/pending-5.10/850-0014-PCI-aardvark-Fix-reading-PCI_EXP_RTSTA_PME-bit-on-em.patch ipq40xx/patches-5.10/105-ipq40xx-fix-sleep-clock.patch All patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Compile-/run-tested: ath79/generic (Archer C7 v2). Signed-off-by: Daniel Golle <daniel@makrotopia.org> [rebased in 22.03 tree] Signed-off-by: John Audia <graysky@archlinux.us> (cherry picked from commit b92ec82235b996ece32bc84af177adf1a4dcb90e)
* ipq806x: fix TP-Link Archer VR2600v bootloopingChristian Lamparter2022-03-161-1/+2
| | | | | | | | | | | | | | | | Timo Schroeder reported: "The TP-Link Archer VR2600v is stuck in a boot loop on written snapshot image. It's able to boot using the snapshot uimage though, but there ath10k firmware can't be found. 21.02.2 release version doesn't have either problem." The VR2600v has a 512 byte header at the beginning of the firmware that needs to be accounted for. Fixes: f6a01d7f5c3d ("ipq806x: convert TP-Link Archer VR2600v to denx,uimage") Reported-by: Timo Schroeder <der.timosch@gmail.com> References: <https://github.com/openwrt/openwrt/issues/9467> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: provide ramoops for R7800/XR500 by defaultHannu Nyman2022-03-081-2/+2
| | | | | | | | | | | | | Add kmod-ramoops to the default set of device packages in R7800 and XR500, so that the ramoops kernel crash logs are provided by default for these routers. The capability was earlier defined by 97158fe1 and cf346dfa, but the feature was not yet turned on by default. The possible kernel crashes are stored into /sys/fs/pstore/* Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* kernel: 5.10: allocate last level PTEs in high memoryRui Salvaterra2022-03-011-1/+1
| | | | | | | | | | Enable support for allocating user space page table entries in high memory [1], for the targets which support this feature. This saves precious low memory (permanently mapped, the only type of memory directly accessible by the kernel). [1] https://www.kernel.org/doc/html/latest/vm/highmem.html Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.102John Audia2022-03-011-19/+19
| | | | | | | | | | | | | | | Removed upstreamed: bcm4908/patches-5.10/180-i2c-brcmstb-fix-support-for-DSL-and-CM-variants.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.102&id=f333c1916fd6b55900029bf8f918cc00009e2111 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.101John Audia2022-03-011-1/+1
| | | | | | | | | | | | | | | | | Removed upstreamed: pending-5.10/841-USB-serial-option-add-ZTE-MF286D-modem.patch[1] bcm27xx/950-0592-drm-vc4-Allow-DBLCLK-modes-even-if-horz-timing-is-od.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=7113440a36c741efd7c76e3d70b3634100120cdb 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.101&id=21c890ca8eaecea06cabb92be2a53a6f26f56383 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <graysky@archlinux.us>
* ipq806x: base-files: asrock: fix bootcount includePetr Štetiar2022-02-281-1/+1
| | | | | | | | | | | | | | | Fixes following warning message during image building process: Finalizing root filesystem... root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling boot root-ipq806x/lib/upgrade/asrock.sh: line 1: /lib/functions.sh: No such file or directory Enabling bootcount Fixes #9350 Fixes: 98b86296e67d ("ipq806x: add support for ASRock G10") Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq806x: Increase kernel size to 4 MB for EA8500/EA7500v1Hannu Nyman2022-02-263-9/+27
| | | | | | | | | | | | | | | | | | | Increase the kernel size from 3 MB to 4 MB for EA8500 and EA7500v1. * modify the common .dtsi * modify the kernel size in the image recipes Define compat-version 2.0 to force factory image usage for sysupgrade. Add explanation message. Reenable both devices. As for 4MiB (and not more): Hannu Nyman noted that: "We have lots of ipq806x devices with 4 MB kernel, so will need action at that point in future in any case. (Assuming that the bootloader did not have a 4 MB limit that has been tested...)" Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi> (squashed, added 4MiB notice of support in ipq806x) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: kernel crash log ramoops storage for R7800 and XR500Hannu Nyman2022-02-241-0/+9
| | | | | | | | | | | | Define the kernel crash log storage ramoops/pstore feature for R7800 and its sister XR500. Reference to the ramoops admin guide in upstream Linux: https://www.kernel.org/doc/html/v5.10/admin-guide/ramoops.html Tested with R7800. Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: disable Linksys EA7500v1 and EA8500Christian Lamparter2022-02-201-0/+2
| | | | | | | | | | | | The kernel of both images will no longer fit into the 3072KiB / 3MiB kernel partition: |Image Name: ARM OpenWrt Linux-5.10.100 |Created: Sat Feb 19 00:11:55 2022 |Image Type: ARM Linux Kernel Image (uncompressed) |Data Size: 3147140 Bytes = 3073.38 KiB = 3.00 MiB Disable both targets for now, until a solution is available. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: update defconfigJohn Audia2022-02-191-7/+1
| | | | | | | | | | | | Enabled `CONFIG_ALL_KMODS` and ran `make kernel_menuconfig` against ipq806x to update defconfig. The removed symbols are in fact present in target/linux/generic/config-5.10. CONFIG_MDIO_DEVRES was likely added due to this: <https://elixir.bootlin.com/linux/v5.10.100/source/drivers/net/phy/Kconfig#L16> Signed-off-by: John Audia <graysky@archlinux.us>
* ipq806x: TP-Link VR2600v convert legacy partitioningChristian Lamparter2022-02-191-88/+92
| | | | | | | | | | | | | This device still had the legacy flash partitioning. This is a problem, because neither the nvmem-cells for mac-address and calibration. Nor the denx,uimage mtd-splitter compatible would be picked up. The patch also changes the node-names of the flash and partition nodes to hopefully meet all the current FDT trends. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: Enlarge D7800 flash - use netgear partitionMike Lothian2022-02-082-7/+4
| | | | | | | | | | | | | | | | | | | | | | Increase the available flash memory size in Netgear R7800 by repurposing the unused "netgear" partition that is located after the firmware partition. Available flash space for kernel+rootfs+overlay increases by 68 MB from 32 MB to 100 MB. In a typical build, overlay space increases from 15 to 85, increasing the package installation possibilities greatly. Reverting to the OEM firmware is still possible, as the OEM firmware contains logic to initialise the "netgear" partition if its contents do not match expectations. In OEM firmware, "netgear" contains 6 UBI sub-partitions that are defined in /etc/netgear.cfg and initialisation is done by /etc/preinit This is based on https://github.com/openwrt/openwrt/commit/fb8a578aa70572b3e56b64d296e22c2931e77b69 Signed-off-by: Mike Lothian <mike@fireburn.co.uk>
* target/linux: replace egrep with grep -ERosen Penev2022-02-071-1/+1
| | | | | | | egrep is deprecated and replaced by grep -E. The latter is used throughout the tree. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq806x: convert TP-Link Archer VR2600v to denx,uimageChristian Lamparter2022-02-063-11/+7
| | | | | | | | | | | | | | | | | | | | | The recent device-tree modification that added pre-cal nvmem-cells pushed the device's kernel+dtb over the allotted 3072k KERNEL_SIZE. > WARNING: Image file tplink_vr2600v-uImage is too big: 3147214 > 3145728 There was a previous kernel partition size upgrade: commit 0c967d92b3d9 ("ipq806x: increase kernel partition size for the TP-Link Archer VR2600v") It has been seemingly upgraded from a 2048k KERNEL_SIZE in the past. The commit talks about using the MTD_SPLIT_TPLINK_FW. But looking at the image make recipe, there is no code that adds a TPLINK header. So instead the board will use "denx,umimage". This requires MTD_SPLIT_UIMAGE_FW, but this is present thanks to some NEC devices. (Maybe the MTD_CONFIG_ARGS can be removed as well? But it could be there because of the padding at the beginning. This needs testing.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: G10: use ASROCK's wifi calibration dataChristian Lamparter2022-02-051-0/+26
| | | | | | | | brings back the ath10k QCA9980 wifi nodes to which it adds ASROCK's wifi calibration data. These are now provided by the ath10k_firmware.git's board-2.bin. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq806x: utilize nvmem-cells for pre-calibration dataChristian Lamparter2022-02-0511-139/+169
| | | | | | | | | | | | | converts extraction entries from 11-ath10k-caldata into nvmem-cells in the individual board's device-tree file. The patch also moves previously existing referenced nvmem-cells data nodes which were placed at the end back into the partitions node. As well as removing some duplicated properties from qcom-ipq8065-xr500.dts's art (the included nighthawk.dtsi defines those already). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.10 to 5.10.96Rui Salvaterra2022-02-011-2/+2
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: convert remaining mtd-mac-address-incrementSungbo Eo2022-02-011-1/+1
| | | | | | | | | | Commit d284e6ef0f06 ("treewide: convert mtd-mac-address-increment* to generic implementation") renamed "mtd-mac-address-increment" property to "mac-address-increment". Convert remaining usages that have been added after that. Fixes: f44e933458b1 ("ipq806x: provide WiFI mac-addresses from dts") Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* kernel: move bootargs-append patch to genericSungbo Eo2022-01-292-14/+2
| | | | | | | | | | This moves bootargs-append support patch from ipq40xx and ipq806x to generic. This way we can append additional boot arguments from DTS instead of only being able to overwrite them. This is a preparation for kirkwood support of ipTIME NAS1. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq806x: Netgear D7800: Fix RAM and enable PCIe #2David Woodhouse2022-01-211-1/+15
| | | | | | | This board has 512MiB of RAM like the R7800, and the VDSL modem is attached to the second PCIe port. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
* ipq806x: janitorial work, respect line lengthsAlex Lewontin2022-01-081-19/+41
| | | | | | | This commit breaks up some lines so that they are shorter than 74 charcters. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ipq806x: modularize generic subtargetAlex Lewontin2022-01-082-430/+431
| | | | | | | | This commit moves the device profiles within the ipq806x/generic subtarget into their own includable .mk file, to support eventually having subtargets other than generic. Signed-off-by: Alex Lewontin <alex.c.lewontin@gmail.com>
* ipq806x: ASRock g10: fix bogus read errorsStefan Lippers-Hollmann2022-01-021-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Properly declare that the g10 is booting from NAND and define its correct (larger than on other devices-) boot_pages_size, to prevent the kernel from constantly falling over missing OOB error correction for the bootloader. This patch prevents a constant slew of (bogus) read errors reported by the kernel and keeping the CPU busy and fixes: blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 8 op 0x0:(READ) flags 0x80700 phys_seg 3 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 16 op 0x0:(READ) flags 0x80700 phys_seg 2 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 24 op 0x0:(READ) flags 0x80700 phys_seg 1 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 0 op 0x0:(READ) flags 0x0 phys_seg 1 prio class 0 Buffer I/O error on dev mtdblock0, logical block 0, async page read blk_update_request: I/O error, dev mtdblock0, sector 32 op 0x0:(READ) flags 0x80700 phys_seg 8 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 40 op 0x0:(READ) flags 0x80700 phys_seg 7 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 48 op 0x0:(READ) flags 0x80700 phys_seg 6 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 56 op 0x0:(READ) flags 0x80700 phys_seg 5 prio class 0 blk_update_request: I/O error, dev mtdblock0, sector 64 op 0x0:(READ) flags 0x80700 phys_seg 4 prio class 0 Buffer I/O error on dev mtdblock0, logical block 1, async page read Buffer I/O error on dev mtdblock1, logical block 0, async page read Buffer I/O error on dev mtdblock1, logical block 1, async page read Buffer I/O error on dev mtdblock2, logical block 0, async page read Buffer I/O error on dev mtdblock2, logical block 1, async page read Buffer I/O error on dev mtdblock3, logical block 0, async page read Buffer I/O error on dev mtdblock3, logical block 0, async page read Buffer I/O error on dev mtdblock4, logical block 0, async page read Buffer I/O error on dev mtdblock4, logical block 1, async page read Suggested-by: Ansuel Smith <ansuelsmth@gmail.com> Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* kernel: 5.10: consolidate mac80211 crypto optionsSergey Ryazanov2021-12-171-7/+0
| | | | | | | | | | | | | | | | | | | | | | Each of - CRYPTO_AEAD2 - CRYPTO_AEAD - CRYPTO_GF128MUL - CRYPTO_GHASH - CRYPTO_HASH2 - CRYPTO_HASH - CRYPTO_MANAGER2 - CRYPTO_MANAGER - CRYPTO_NULL2 either directly required for mac80211 crypto support, or directly selected by such options. Support for the mac80211 crypto was enabled in the generic config since c7182123b9 ("kernel: make cryptoapi support needed by mac80211 built-in"). So move the above options from the target configs to the generic config to make it clear why do we need them. CC: Felix Fietkau <nbd@nbd.name> Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: filter out both Clang and LLD versionsSergey Ryazanov2021-12-171-1/+0
| | | | | | | | Both CLANG_VERSION and LLD_VERISON are autogenerated runtime configuration options, so add them to the kernel configuration filter and remove from generic and per-target configs to keep configs clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: bump 5.10 to 5.10.83John Audia2021-12-122-9/+9
| | | | | | | | | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0024-ARM-dts-BCM5301X-Fix-I2C-controller-interrupt.patch[1] bcm53xx/patches-5.10/033-v5.16-0025-ARM-dts-BCM5301X-Add-interrupt-properties-to-GPIO-no.patch[2] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=b2cd6fdcbe0a5cb44e4610a08cc58261d494a885 2. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.83&id=9db1d4a3c2700e1cc84c3d61199411d75c2a3ec6 Build system: x86_64* Build-tested: bcm2711/RPi4B, ipq806x/R7800† Run-tested: bcm2711/RPi4B, ipq806x/R7800† * Had to revert 7c99085bd69742f66207d61e9f2da5ec4f8f9d2f in order to build (latest bump of ca-certificates) † Had to revert 7f1edbd41295dff9f2127b169fbc086c0fb2c14e in order to build (binutils 2.37, https://bugs.openwrt.org/index.php?do=details&task_id=4149) Signed-off-by: John Audia <graysky@archlinux.us>
* ipq806x: revert SDC clock changes for NBG6817 MMCShane Synan2021-12-052-24/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Revert the SDC "CLK_SET_RATE_GATE" changes to the SDC clock regulator structures. See https://elinux.org/images/b/b8/Elc2013_Clement.pdf > if ((clk->flags & CLK_SET_RATE_GATE) && clk->prepare_count) { > > For this particular clock, setting its rate is possible only if the > clock is ungated (not yet prepared) This fixes the MMC failing to initialize on newer ZyXEL NBG6817 hardware revisions with Kingston MMC. Older revisions should hopefully be unaffected. Check MMC hardware details with: cd /sys/block/mmcblk0/device/ && \ tail -v cid date name manfid fwrev hwrev oemid rev Known problematic MMC names (broken before this commit): * M62704 (dated 12/2018) via myself * M62704 (dated 11/2018) via Drake Stefani Known unaffected MMC names (already working without this commit): * S10004 (dated 12/2015) via slh Without enabling dynamic debugging, this error manifests in the kernel hardware serial console as the following: [ 2.746605] mmc0: error -110 whilst initialising MMC card […trimmed other messages…] [ 2.877832] Waiting for root device /dev/mmcblk0p5... Enabling Linux dynamic kernel debugging provides additional messages. For guidance, see the Linux kernel documentation: https://www.kernel.org/doc/html/latest/admin-guide/dynamic-debug-howto.html First, enable dynamic debugging in OpenWRT's configuration: 1. Run "make menuconfig" 2. Select "Global build settings --->" 3. Select "Kernel build options --->" 4. Enable "Compile the kernel with dynamic printk" via spacebar 5. Save and exit (arrow key to "Exit" until prompted to save, save) Alternatively, set "CONFIG_KERNEL_DYNAMIC_DEBUG=y" in your .config. Then, turn on dynamic debugging at boot: Modify bootargs in target/linux/ipq806x/files/arch/arm/boot/dts/qcom-ipq8065-nbg6817.dts to add… bootargs = "[…existing bootargs…] dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8"; For example: chosen { - bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1"; + bootargs = "rootfstype=squashfs,ext4 rootwait noinitrd fstools_ignore_partname=1 dyndbg=\"file drivers/mmc/* +p\" dynamic_debug.verbose=1 loglevel=8"; append-rootblock = "root=/dev/mmcblk0p"; Then, compile and flash the resulting build. If you are testing before this commit on newer MMC hardware, be prepared to recover! NOTE: If you have hardware serial console access, you don't need to use TFTP recovery to change the active boot partition. Reboot to working alternative partition via serial console: 1. Connect to hardware serial console * See https://openwrt.org/toh/zyxel/nbg6817#serial 2. Interrupt boot at "Hit any key to stop autoboot:" 3. Run "ATSE NBG6817" 4. Copy the result (e.g. "001976FE4B04") * Changes with **every boot** - can't reuse this 5. On your local system, run "./zyxel-uboot-password-tool.sh <copied value here>" * Example: "./zyxel-uboot-password-tool.sh 001976FE4B04" 6. Run the command provided by the password tool * Example: "ATEN 1,910F129B" * Changes with **every boot** - can't reuse this 7. Run "ATGU" * You now have full u-boot shell until next boot - unlocking is not remembered 8. Run either "run boot_mmc" (for booting partition set "FF") or "run boot_mmc_1" (for booting partition set "01") * These commands are not affected by dual-boot partition flags NOTE: This will NOT set the dual-boot partition flag. You'll need to fix that manually. The "nbg6817-dualboot" script may help: https://github.com/pkgadd/nbg6817/blob/master/nbg6817-dualboot zyxel-uboot-password-tool.sh - sourced from commit 459c8c9ef816156107e297964d088ddee2b4eef5: ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ a )) printf "ATEN 1,%X\n" $p Kernel serial console log BEFORE commit with dynamic debug enabled: […trimmed…] [ 3.171343] mmci-pl18x 12400000.sdcc: designer ID = 0x51 [ 3.171397] mmci-pl18x 12400000.sdcc: revision = 0x0 [ 3.175811] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz [ 3.181134] mmci-pl18x 12400000.sdcc: No vqmmc regulator found [ 3.186788] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio) [ 3.192902] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2 [ 3.215609] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0 [ 3.227532] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v [ 3.247518] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0 […trimmed…] [ 3.997725] mmc0: req done (CMD2): -110: 00000000 00000000 00000000 00000000 [ 4.003631] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000 [ 4.003659] mmc0: error -110 whilst initialising MMC card [ 4.016481] mmc0: clock 0Hz busmode 2 powermode 0 cs 0 Vdd 0 width 1 timing 0 Notice how the initial clock is 52 MHz, which is incorrect - MMC requires negotiation to enable higher speeds. Kernel serial console log AFTER commit with dynamic debug enabled: […trimmed…] [ 3.168996] mmci-pl18x 12400000.sdcc: designer ID = 0x51 [ 3.169051] mmci-pl18x 12400000.sdcc: revision = 0x0 [ 3.173492] mmci-pl18x 12400000.sdcc: clocking block at 96000000 Hz [ 3.178808] mmci-pl18x 12400000.sdcc: No vqmmc regulator found [ 3.184702] mmci-pl18x 12400000.sdcc: mmc0: PL180 manf 51 rev0 at 0x12400000 irq 41,0 (pio) [ 3.190573] mmci-pl18x 12400000.sdcc: DMA channels RX dma1chan1, TX dma1chan2 [ 3.217873] mmc0: clock 0Hz busmode 2 powermode 1 cs 0 Vdd 21 width 1 timing 0 [ 3.229250] mmci-pl18x 12400000.sdcc: Initial signal voltage of 3.3v [ 3.249111] mmc0: clock 400000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 0 […trimmed…] [ 4.392652] mmci-pl18x 12400000.sdcc: irq0 (data+cmd) 00000000 [ 4.392785] mmc0: clock 52000000Hz busmode 2 powermode 2 cs 0 Vdd 21 width 1 timing 1 [ 4.406554] mmc0: starting CMD6 arg 03b70201 flags 0000049d […trimmed…] Now, the MMC properly initializes and later switches to high speed. Thanks to: * Ansuel for maintaining/help with the IPQ806x platform, kernel code * slh for additional debugging and suggestions * dwfreed for confirming newer MMC details, clock frequency * robimarko for device driver debug printing help, clock debugging * Drake for testing and confirmation with their own newer NBG6817 ...and anyone else I missed! Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com> Tested-by: Shane Synan <digitalcircuit36939@gmail.com>
* ipq806x: sysupgrade: drop unnecessary UBI to UBI logicBjørn Mork2021-12-031-17/+1
| | | | | | | | | | | | | The purpose of this code seems to be to avoid issues caused by partially overwriting an existing UBI partition, where some of the erase counters would be reset but not the unmodified ones. This problem has been solved in a more generic way by the UBI EOF marker. This ensures that any old PEBs after the marker are properly initialized. It is therefore unnecessary to erase the whole partition before flashing a new OpenWrt factory image. Signed-off-by: Bjørn Mork <bjorn@mork.no>
* ipq806x: add support for Cisco Meraki MR42/MR52Matthew Hagan2021-11-289-1/+755
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MR42 and MR52 are two similar IPQ806x based devices from the Cisco Meraki "Cryptid" series. MR42 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9992 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 1x AR8033 PHY - PoE/AC power MR52 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9994 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 2x AR8033 PHYs - PoE/AC power (MR42 Only) Installation via diagnostic mode: If you can successfully complete step 1 then you can continue to install via this method without having to open the device. Otherwise please use the standard UART method. Please note that when booting via TFTP, some Ethernet devices, in particular those on laptops, will not connect in time, resulting in TFTP boot not succeeding. In this instance it is advised to connect via a switch. 1. Hold down reset at power on and keep holding, after around 10 seconds if the orange LED changes behaviour to begin flashing, proceed to release reset, then press reset two times. Ensure that the LED has turned blue. Note that flashing will occur on some devices, but it will not be possible to change the LED colour using the reset button. In this case it will still be possible to continue with this install method. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving mr42_u-boot.mbn and openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained from [1]. 3. Use telnet and connect to 192.168.1.1. Run the following commands to install u-boot. Note that all these commands are critical, an error will likely render the device unusable. Option 3.1: If you are sure you have set up the TFTP server correctly you can run this script on the device. This will download and flash the u-boot image immediately: `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn` Once completed successfully, power off the device. Option 3.2: If you are unsure the TFTP server is correctly set up you can obtain the image and flash manually: 3.2.1. `cd /tmp` 3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn` 3.2.3. Confirm file has downloaded correctly by comparing the md5sum: `md5sum mr42_u-boot.mbn` 3.2.4. The following are the required commands to write the image. `echo 1 > /sys/devices/platform/msm_nand/boot_layout mtd erase /dev/mtd1 nandwrite -pam /dev/mtd1 mr42_u-boot.mbn echo 0 > /sys/devices/platform/msm_nand/boot_layout` Important: You must observe the output of the `nandwrite` command. Look for the following to verify writing is occurring: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` If you do not see this then do not power off the device. Check your previous commands and that mr42_u-boot.mbn was downloaded correctly. Once you are sure the image has been written you can proceed to power off the device. 4. Hold the reset button and power on the device. This will immediately begin downloading the appropriate initramfs image and boot into it. Note: If the device does not download the initramfs, this is likely due to the interface not being brought up in time. Changing Ethernet source to a router or switch will likely resolve this. You can also try manually setting the link speed to 10Mb/s Half-Duplex. 5. Once a solid white LED is displayed on the device, continue to the UART installation method, step 6. Standard installation via UART - MR42 & MR52 1. Disassemble the device and connect a UART header. The header pinout is as follows: 1 - 3.3v 2 - TXD 3 - RXD 4 - GND Important: You should only connect TXD, RXD and GND. Connecting 3.3v may damage the device. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb. Separately obtain the respective sysupgrade image. 3. Run the following commands, preferably from a Linux host. The mentioned files, including ubootwrite.py and u-boot images, can be obtained from [1]. `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin` The default for "--serial" option is /dev/ttyUSB0. 4. Power on the device. The ubootwrite script will upload the image to the device and launch it. The second stage u-boot will in turn load the initramfs image by TFTP, provided the TFTP server is running correctly. This process will take about 13 minutes. Once a solid white LED is displayed, the image has successfully finished loading. Note: If the image does not load via TFTP, try again with the Ethernet link to 10Mb/s Half-Duplex. 5. (MR42 only) Do not connect over the network. Instead connect over the UART using minicom or similar tool. To replace u-boot with the network enabled version, please run the following commands. Note that in the provided initramfs images, the u-boot.mbn file is located in /root: If you have not used the provided initramfs, you must ensure you are using an image with "boot_layout" ECC configuration enabled in the Kernel. This will be version 5.10 or higher. If you do not do this correctly the device will be bricked. `insmod mtd-rw i_want_a_brick=1 mtd erase /dev/mtd8 nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn` After running nandwrite, ensure you observe the following output: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` 6. (Optional) If you have no further use for the Meraki OS, you can remove all other UBI volumes on ubi0 (mtd11), including diagnostic1, part.old, storage and part.safe. You must not remove the ubi1 ART partition (mtd12). `for i in diagnostic1 part.old storage part.safe ; do ubirmvol /dev/ubi0 -N $i done` 7. Proceed to flash the sysupgrade image via luci, or else download or scp the image to /tmp and use the sysupgrade command. [1] The mentioned images and ubootwrite.py script can be found in this repo: https://github.com/clayface/openwrt-cryptid [2] The modified u-boot sources for the MR42 and MR52 are available: https://github.com/clayface/U-boot-MR52-20200629 Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add gsbi2_i2c labelMatthew Hagan2021-11-281-0/+9
| | | | | | gsbi2_i2c is used by the Meraki MR42 so we need to expose a label here. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: backport GMAC_AHB_RESET deassert patchesMatthew Hagan2021-11-282-0/+139
| | | | | | | | | Add backports of the following patches: "net: stmmac: explicitly deassert GMAC_AHB_RESET" and "ARM: dts: qcom: add ahb reset to ipq806x-gmac" Required for Meraki MR42/MR52. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add GSBI nodes to ipq8064-dtsi-addidionsMatthew Hagan2021-11-283-51/+96
| | | | | | | | | Rather than having separate patches for each GSBI node added, this patch consolidates the existing GSBI1 patch into 083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes, required for the MR42 and MR52 respectively, are added. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* kernel: bump 5.10 to 5.10.82John Audia2021-11-271-2/+2
| | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch Manually rebased: ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.81John Audia2021-11-271-1/+1
| | | | | | | | | | | | | Manually rebased: octeontx/patches-5.10/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.80Rui Salvaterra2021-11-191-3/+3
| | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1] bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2] lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3] lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4] lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5] lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6] Manually rebased: ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0 [5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f [6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.10: packet mangling code only for ar8216 driverMathias Kresin2021-11-021-0/+1
| | | | | | | | Only the ar8216 switch driver uses the packet mangling code. Update the kernel configs accordingly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: ecw5410: use bootloader provided MAC-sRobert Marko2021-10-312-4/+2
| | | | | | | | | | | Currently, we are overriding the bootloader provided MAC-s as the ethernet aliases are reversed so MAC-s were fixed up in userspace. There is no need to do that as we can just fix the aliases instead and get rid of MAC setting via userspace helper. Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: ecw5410: fix PCI1 radio caldataRobert Marko2021-10-311-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | ECW5410 has 2 QCA9984 cards, one per PCI controller. They are located at PCI adresses 0001:01:00.0 and 0002:01:00.0. Currently, pre-cal is not provided for 0001:01:00.0 at all,but for 0000:01:00.0 which is incorrect and causes the ath10k driver to not be able to fetch the BMI ID and use that to fetch the proper BDF but rather fail with: [ 12.029708] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 12.031816] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 12.037660] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 13.173898] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 13.174015] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.189304] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc35 [ 15.492322] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Edgecore-ECW541 from ath10k/QCA9984/hw1.0/board-2.bin [ 15.543883] ath10k_pci 0001:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0 [ 15.543920] ath10k_pci 0001:01:00.0: failed to fetch board file: -12 [ 15.552281] ath10k_pci 0001:01:00.0: could not probe fw (-12) So, provide the pre-cal for the actual PCI card and not the non-existent one. Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: ecw5410: drop GPIO based MDIO1 nodeRobert Marko2021-10-311-19/+10
| | | | | | | | | | | | It looks like this is a leftover before there was a proper MDIO driver. Since both PHY-s are connected to the HW MDIO bus there is no reason for this to exist anymore, especially since it uses the same pins as the HW controller and has the pinmux for the set to "MDIO" so this worked by pure luck as GPIO MDIO would probe first and override the HW driver. Move the GMAC3 to simply use the same MDIO bus phandle. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: consolidate 11-ath10k-caldataAdrian Schmutzler2021-10-301-26/+12
| | | | | | | After the ath10k_patch_mac lines have been removed, a lot of blocks can be consolidated. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: remove transition workarounds for qcom-smem partitionsAdrian Schmutzler2021-10-304-56/+10
| | | | | | | | | | | | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switched to normalizing the partition names to lower case. While both 5.4 and 5.10 were supported in the target, we carried a workaround to support both of them. Since the target has dropped 5.4 recently, those can be removed now. Ref: 2db9dded0a1a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions") 435dc2e77e3b ("ipq806x: ecw5410: case-insensitive qcom-smem partitions") f70e11cd974e ("ipq806x: g10: case-insensitive qcom-smem partitions") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: provide WiFI mac-addresses from dtsAnsuel Smith2021-10-308-12/+216
| | | | | | | | | | Use nvmem framework for supported mac-address stored in nvmem cells and drop mac patch function for hotplug script for supported devices. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [rebase, move to correct node for d7800, include xr500] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.10 to 5.10.76Rui Salvaterra2021-10-303-3/+3
| | | | | | | | | | | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1] Manually rebased: bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch Note: although automatically rebaseable, the last patch has been edited to avoid conflicting bit definitions. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: add support for Netgear Nighthawk Pro Gaming XR500Peter Geis2021-10-269-448/+545
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear Nighthawk Pro Gaming XR500. It is the successor to the Netgear Nighthawk R7800 and shares almost identical hardware to that device. The stock firmware is a heavily modified version of OpenWRT. Specifications: SoC: Qualcomm Atheros IPQ8065 RAM: 512 MB Storage: 256 MiB NAND Flash Wireless: 2x Qualcomm Atheros QCA9984 Ethernet: 2x 1000/100/10 dedicated interfaces Switch: 5x 1000/100/10 external ports USB: 2x 3.0 ports More information: Manufacturer page: https://www.netgear.com/gaming/xr500/ Almost identical to Netgear R7800 Differences (r7800 > xr500): Flash: 128MiB > 256MiB Removed esata swapped leds: usb1 (gpio 7 > 8) usb2 (gpio 8 > 26) guest/esata (gpio 26 > 7) MAC addresses: On the OEM firmware, the mac addresses are: WAN: *:50 art 0x6 LAN: *:4f art 0x0 (label) 2G: *:4f art 0x0 5G: *:51 art 0xc Installation: Install via Web Interface (preferred): Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img Install via TFTP recovery: 1.Turn off the power, push and hold the reset button (in a hole on backside) with a pin 2.Turn on the power and wait till power led starts flashing white (after it first flashes orange for a while) 3.Release the reset button and tftp the factory img in binary mode. The power led will stop flashing if you succeeded in transferring the image, and the router reboots rather quickly with the new firmware. 4.Try to ping the router (ping 192.168.1.1). If does not respond, then tftp will not work either. Uploading the firmware image with a TFTP client $ tftp 192.168.1.1 bin put openwrt-ipq806x-netgear_xr500-squashfs-factory.img Note: The end of the last partition is at 0xee00000. This was chosen by the initial author, but nobody was able to tell why this particular arbitrary size was chosen. Since it's not leaving too much empty space and it's the only issue left, let's just keep it for now. Based on work by Adam Hnat <adamhnat@gmail.com> ref: https://github.com/openwrt/openwrt/pull/3215 Signed-off-by: Peter Geis <pgwipeout@gmail.com> [squash commits, move common LEDs to DTSI, remove SPDX on old files, minor whitespace cleanup, commit message facelift, add MAC address overview, add Notes, fix MAC addresses, use generic name for partition nodes in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: remove obsolete Kernel 5.4Paul Spooren2021-10-0246-8294/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>