aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add support for Cisco Meraki MR42/MR52Matthew Hagan2021-11-289-1/+755
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MR42 and MR52 are two similar IPQ806x based devices from the Cisco Meraki "Cryptid" series. MR42 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9992 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 1x AR8033 PHY - PoE/AC power MR52 main features: - IPQ8068 1.4GHz - 512MB RAM - 128MB NAND - 2x QCA9994 (2.4 & 5GHz) - 1x QCA9889 (2.4 & 5GHz) - 2x AR8033 PHYs - PoE/AC power (MR42 Only) Installation via diagnostic mode: If you can successfully complete step 1 then you can continue to install via this method without having to open the device. Otherwise please use the standard UART method. Please note that when booting via TFTP, some Ethernet devices, in particular those on laptops, will not connect in time, resulting in TFTP boot not succeeding. In this instance it is advised to connect via a switch. 1. Hold down reset at power on and keep holding, after around 10 seconds if the orange LED changes behaviour to begin flashing, proceed to release reset, then press reset two times. Ensure that the LED has turned blue. Note that flashing will occur on some devices, but it will not be possible to change the LED colour using the reset button. In this case it will still be possible to continue with this install method. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving mr42_u-boot.mbn and openwrt-ipq806x-generic-meraki_mr42-initramfs-fit-uImage.itb, obtained from [1]. 3. Use telnet and connect to 192.168.1.1. Run the following commands to install u-boot. Note that all these commands are critical, an error will likely render the device unusable. Option 3.1: If you are sure you have set up the TFTP server correctly you can run this script on the device. This will download and flash the u-boot image immediately: `/etc/update_uboot.sh 192.168.1.250 mr42_u-boot.mbn` Once completed successfully, power off the device. Option 3.2: If you are unsure the TFTP server is correctly set up you can obtain the image and flash manually: 3.2.1. `cd /tmp` 3.2.2. `tftp-hpa 192.168.1.250 -m binary -c get mr42_u-boot.mbn` 3.2.3. Confirm file has downloaded correctly by comparing the md5sum: `md5sum mr42_u-boot.mbn` 3.2.4. The following are the required commands to write the image. `echo 1 > /sys/devices/platform/msm_nand/boot_layout mtd erase /dev/mtd1 nandwrite -pam /dev/mtd1 mr42_u-boot.mbn echo 0 > /sys/devices/platform/msm_nand/boot_layout` Important: You must observe the output of the `nandwrite` command. Look for the following to verify writing is occurring: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` If you do not see this then do not power off the device. Check your previous commands and that mr42_u-boot.mbn was downloaded correctly. Once you are sure the image has been written you can proceed to power off the device. 4. Hold the reset button and power on the device. This will immediately begin downloading the appropriate initramfs image and boot into it. Note: If the device does not download the initramfs, this is likely due to the interface not being brought up in time. Changing Ethernet source to a router or switch will likely resolve this. You can also try manually setting the link speed to 10Mb/s Half-Duplex. 5. Once a solid white LED is displayed on the device, continue to the UART installation method, step 6. Standard installation via UART - MR42 & MR52 1. Disassemble the device and connect a UART header. The header pinout is as follows: 1 - 3.3v 2 - TXD 3 - RXD 4 - GND Important: You should only connect TXD, RXD and GND. Connecting 3.3v may damage the device. 2. Set your IP to 192.168.1.250. Set up a TFTP server serving openwrt-ipq806x-generic-meraki_(mr42|mr52)-initramfs-fit-uImage.itb. Separately obtain the respective sysupgrade image. 3. Run the following commands, preferably from a Linux host. The mentioned files, including ubootwrite.py and u-boot images, can be obtained from [1]. `python ubootwrite.py --write=(mr42|mr52)_u-boot.bin` The default for "--serial" option is /dev/ttyUSB0. 4. Power on the device. The ubootwrite script will upload the image to the device and launch it. The second stage u-boot will in turn load the initramfs image by TFTP, provided the TFTP server is running correctly. This process will take about 13 minutes. Once a solid white LED is displayed, the image has successfully finished loading. Note: If the image does not load via TFTP, try again with the Ethernet link to 10Mb/s Half-Duplex. 5. (MR42 only) Do not connect over the network. Instead connect over the UART using minicom or similar tool. To replace u-boot with the network enabled version, please run the following commands. Note that in the provided initramfs images, the u-boot.mbn file is located in /root: If you have not used the provided initramfs, you must ensure you are using an image with "boot_layout" ECC configuration enabled in the Kernel. This will be version 5.10 or higher. If you do not do this correctly the device will be bricked. `insmod mtd-rw i_want_a_brick=1 mtd erase /dev/mtd8 nandwrite -pam /dev/mtd8 /root/mr42_u-boot.mbn` After running nandwrite, ensure you observe the following output: `Writing data to block 0 at offset 0x0 Writing data to block 1 at offset 0x20000 Writing data to block 2 at offset 0x40000` 6. (Optional) If you have no further use for the Meraki OS, you can remove all other UBI volumes on ubi0 (mtd11), including diagnostic1, part.old, storage and part.safe. You must not remove the ubi1 ART partition (mtd12). `for i in diagnostic1 part.old storage part.safe ; do ubirmvol /dev/ubi0 -N $i done` 7. Proceed to flash the sysupgrade image via luci, or else download or scp the image to /tmp and use the sysupgrade command. [1] The mentioned images and ubootwrite.py script can be found in this repo: https://github.com/clayface/openwrt-cryptid [2] The modified u-boot sources for the MR42 and MR52 are available: https://github.com/clayface/U-boot-MR52-20200629 Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add gsbi2_i2c labelMatthew Hagan2021-11-281-0/+9
| | | | | | gsbi2_i2c is used by the Meraki MR42 so we need to expose a label here. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: backport GMAC_AHB_RESET deassert patchesMatthew Hagan2021-11-282-0/+139
| | | | | | | | | Add backports of the following patches: "net: stmmac: explicitly deassert GMAC_AHB_RESET" and "ARM: dts: qcom: add ahb reset to ipq806x-gmac" Required for Meraki MR42/MR52. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* ipq806x: add GSBI nodes to ipq8064-dtsi-addidionsMatthew Hagan2021-11-283-51/+96
| | | | | | | | | Rather than having separate patches for each GSBI node added, this patch consolidates the existing GSBI1 patch into 083-ipq8064-dtsi-additions.patch. In addition, GSBI6 and GSBI7 I2C nodes, required for the MR42 and MR52 respectively, are added. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* kernel: bump 5.10 to 5.10.82John Audia2021-11-271-2/+2
| | | | | | | | | | | | | | | | Removed upstreamed: bcm53xx/patches-5.10/033-v5.16-0014-ARM-dts-NSP-Fix-mpcore-mmc-node-names.patch Manually rebased: ipq806x/patches-5.10/086-ipq8064-fix-duplicate-node.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.81John Audia2021-11-271-1/+1
| | | | | | | | | | | | | Manually rebased: octeontx/patches-5.10/0004-PCI-add-quirk-for-Gateworks-PLX-PEX860x-switch-with-.patch All other patches automatically rebased. Build system: x86_64 Build-tested: bcm2711/RPi4B, ipq806x/R7800 Run-tested: bcm2711/RPi4B, ipq806x/R7800 Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.80Rui Salvaterra2021-11-191-3/+3
| | | | | | | | | | | | | | | | | | | | | | Deleted (upstreamed): ath79/patches-5.10/921-serial-core-add-support-for-boot-console-with-arbitr.patch [1] bcm53xx/patches-5.10/033-v5.15-0012-ARM-dts-BCM5301X-Fix-memory-nodes-names.patch [2] lantiq/patches-5.10/0016-mtd-rawnand-xway-Keep-the-driver-compatible-with-on-.patch [3] lantiq/patches-5.10/0110-MIPS-lantiq-dma-add-small-delay-after-reset.patch [4] lantiq/patches-5.10/0111-MIPS-lantiq-dma-reset-correct-number-of-channel.patch [5] lantiq/patches-5.10/0112-MIPS-lantiq-dma-fix-burst-length-for-DEU.patch [6] Manually rebased: ipq806x/patches-5.10/0065-arm-override-compiler-flags.patch [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=47462c5e600fbaffd755cd13dedd80d04e41ff83 [2] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=2fde76df1885a6bec04317e457121326070450eb [3] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=9b366f5221d8aa64b22f35be137a5749326444ce [4] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=5af57ce8a6155fe3e4270d28d171abf8903bebc0 [5] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=b92a5df2c7adc79a57481445f67de0c1c716581f [6] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.10.80&id=6b72caabc47011d03f44064452b2c65e8ed18326 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: 5.10: packet mangling code only for ar8216 driverMathias Kresin2021-11-021-0/+1
| | | | | | | | Only the ar8216 switch driver uses the packet mangling code. Update the kernel configs accordingly. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: ecw5410: use bootloader provided MAC-sRobert Marko2021-10-312-4/+2
| | | | | | | | | | | Currently, we are overriding the bootloader provided MAC-s as the ethernet aliases are reversed so MAC-s were fixed up in userspace. There is no need to do that as we can just fix the aliases instead and get rid of MAC setting via userspace helper. Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: ecw5410: fix PCI1 radio caldataRobert Marko2021-10-311-2/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | ECW5410 has 2 QCA9984 cards, one per PCI controller. They are located at PCI adresses 0001:01:00.0 and 0002:01:00.0. Currently, pre-cal is not provided for 0001:01:00.0 at all,but for 0000:01:00.0 which is incorrect and causes the ath10k driver to not be able to fetch the BMI ID and use that to fetch the proper BDF but rather fail with: [ 12.029708] ath10k 5.10 driver, optimized for CT firmware, probing pci device: 0x46. [ 12.031816] ath10k_pci 0001:01:00.0: enabling device (0140 -> 0142) [ 12.037660] ath10k_pci 0001:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0 [ 13.173898] ath10k_pci 0001:01:00.0: qca9984/qca9994 hw1.0 target 0x01000000 chip_id 0x00000000 sub 168c:cafe [ 13.174015] ath10k_pci 0001:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0 [ 13.189304] ath10k_pci 0001:01:00.0: firmware ver 10.4b-ct-9984-fW-13-5ae337bb1 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc35 [ 15.492322] ath10k_pci 0001:01:00.0: failed to fetch board data for bus=pci,vendor=168c,device=0046,subsystem-vendor=168c,subsystem-device=cafe,variant=Edgecore-ECW541 from ath10k/QCA9984/hw1.0/board-2.bin [ 15.543883] ath10k_pci 0001:01:00.0: failed to fetch board-2.bin or board.bin from ath10k/QCA9984/hw1.0 [ 15.543920] ath10k_pci 0001:01:00.0: failed to fetch board file: -12 [ 15.552281] ath10k_pci 0001:01:00.0: could not probe fw (-12) So, provide the pre-cal for the actual PCI card and not the non-existent one. Fixes: 59f0a0f ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: ecw5410: drop GPIO based MDIO1 nodeRobert Marko2021-10-311-19/+10
| | | | | | | | | | | | It looks like this is a leftover before there was a proper MDIO driver. Since both PHY-s are connected to the HW MDIO bus there is no reason for this to exist anymore, especially since it uses the same pins as the HW controller and has the pinmux for the set to "MDIO" so this worked by pure luck as GPIO MDIO would probe first and override the HW driver. Move the GMAC3 to simply use the same MDIO bus phandle. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: consolidate 11-ath10k-caldataAdrian Schmutzler2021-10-301-26/+12
| | | | | | | After the ath10k_patch_mac lines have been removed, a lot of blocks can be consolidated. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: remove transition workarounds for qcom-smem partitionsAdrian Schmutzler2021-10-304-56/+10
| | | | | | | | | | | | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switched to normalizing the partition names to lower case. While both 5.4 and 5.10 were supported in the target, we carried a workaround to support both of them. Since the target has dropped 5.4 recently, those can be removed now. Ref: 2db9dded0a1a ("ipq806x: nbg6817: case-insensitive qcom-smem partitions") 435dc2e77e3b ("ipq806x: ecw5410: case-insensitive qcom-smem partitions") f70e11cd974e ("ipq806x: g10: case-insensitive qcom-smem partitions") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: provide WiFI mac-addresses from dtsAnsuel Smith2021-10-308-12/+216
| | | | | | | | | | Use nvmem framework for supported mac-address stored in nvmem cells and drop mac patch function for hotplug script for supported devices. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [rebase, move to correct node for d7800, include xr500] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.10 to 5.10.76Rui Salvaterra2021-10-303-3/+3
| | | | | | | | | | | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0145-xhci-add-quirk-for-host-controllers-that-don-t-updat.patch [1] Manually rebased: bcm27xx/patches-5.10/950-0355-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch Note: although automatically rebaseable, the last patch has been edited to avoid conflicting bit definitions. [1] https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=linux-5.10.y&id=b6f32897af190d4716412e156ee0abcc16e4f1e5 Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: add support for Netgear Nighthawk Pro Gaming XR500Peter Geis2021-10-269-448/+545
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear Nighthawk Pro Gaming XR500. It is the successor to the Netgear Nighthawk R7800 and shares almost identical hardware to that device. The stock firmware is a heavily modified version of OpenWRT. Specifications: SoC: Qualcomm Atheros IPQ8065 RAM: 512 MB Storage: 256 MiB NAND Flash Wireless: 2x Qualcomm Atheros QCA9984 Ethernet: 2x 1000/100/10 dedicated interfaces Switch: 5x 1000/100/10 external ports USB: 2x 3.0 ports More information: Manufacturer page: https://www.netgear.com/gaming/xr500/ Almost identical to Netgear R7800 Differences (r7800 > xr500): Flash: 128MiB > 256MiB Removed esata swapped leds: usb1 (gpio 7 > 8) usb2 (gpio 8 > 26) guest/esata (gpio 26 > 7) MAC addresses: On the OEM firmware, the mac addresses are: WAN: *:50 art 0x6 LAN: *:4f art 0x0 (label) 2G: *:4f art 0x0 5G: *:51 art 0xc Installation: Install via Web Interface (preferred): Utilize openwrt-ipq806x-netgear_xr500-squashfs-factory.img Install via TFTP recovery: 1.Turn off the power, push and hold the reset button (in a hole on backside) with a pin 2.Turn on the power and wait till power led starts flashing white (after it first flashes orange for a while) 3.Release the reset button and tftp the factory img in binary mode. The power led will stop flashing if you succeeded in transferring the image, and the router reboots rather quickly with the new firmware. 4.Try to ping the router (ping 192.168.1.1). If does not respond, then tftp will not work either. Uploading the firmware image with a TFTP client $ tftp 192.168.1.1 bin put openwrt-ipq806x-netgear_xr500-squashfs-factory.img Note: The end of the last partition is at 0xee00000. This was chosen by the initial author, but nobody was able to tell why this particular arbitrary size was chosen. Since it's not leaving too much empty space and it's the only issue left, let's just keep it for now. Based on work by Adam Hnat <adamhnat@gmail.com> ref: https://github.com/openwrt/openwrt/pull/3215 Signed-off-by: Peter Geis <pgwipeout@gmail.com> [squash commits, move common LEDs to DTSI, remove SPDX on old files, minor whitespace cleanup, commit message facelift, add MAC address overview, add Notes, fix MAC addresses, use generic name for partition nodes in DTS] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: remove obsolete Kernel 5.4Paul Spooren2021-10-0246-8294/+0
| | | | | | | With the upgrade to Kernel 5.10 per default the old version is no longer required to be in tree. Signed-off-by: Paul Spooren <mail@aparcar.org>
* kernel: bump 5.4 to 5.4.150Hauke Mehrtens2021-10-021-1/+1
| | | | | | | | | | | | | | | | Manually rebased: generic/pending-5.4/800-bcma-get-SoC-device-struct-copy-its-DMA-params-to-th.patch mvebu/patches-5.4/021-arm64-dts-marvell-armada-37xx-Move-PCIe-comphy-handl.patch Removed upstreamed: layerscape/patches-5.4/819-uart-0004-MLK-18137-fsl_lpuart-Fix-loopback-mode.patch All others updated automatically. Compile-tested on: lantiq/xrx200, armvirt/64 Runtime-tested on: lantiq/xrx200, armvirt/64 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 5.10 to 5.10.67Rui Salvaterra2021-09-301-1/+1
| | | | | | | Deleted (upstreamed): bcm27xx/patches-5.10/950-0312-vc4_hdmi-Set-HD_CTL_WHOLSMP-and-HD_CTL_CHALIGN_SET.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: switch to kernel 5.10Ansuel Smith2021-09-121-2/+1
| | | | | | | | | Move kernel version to 5.10 as has been tested by many users with positive feedback. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> [Tested on: ipq8064/g10; ipq8065/nbg6817] Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* kernel: Set CONFIG_RCU_CPU_STALL_TIMEOUT=21Hauke Mehrtens2021-09-092-2/+0
| | | | | | | | | | | | The default value for CONFIG_RCU_CPU_STALL_TIMEOUT was changed from 60 seconds to 21 seconds in 2012 in the upstream kernel. Some targets already use 21 seconds. This patch changes the default value in the generic configuration to 21 seconds and removes the target specific configuration options. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Acked-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: add missing enclosing partitions block for TP-Link C2600Filip Matijević2021-08-301-146/+152
| | | | | | | | | | | | | | | | | | | | The partitions that have compatible property set are skipped by mtd if they are not contained inside a partitions node and this breaks fetching MAC address from "default-mac" partition. Fix this by defining all the partitions inside partitions node with compatible = "fixed-partitions" as nvmem requires the standard partitions scheme to work correctly. Fixes: FS#3945 Fixes: cd36d71655ee ("ipq806x/dts: Add Archer C2600 DTS") Fixes: 0458a8993ca1 ("ipq806x: convert mtd-mac-address to nvmem implementation") Signed-off-by: Filip Matijević <filip.matijevic.pz@gmail.com> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com> [adjust commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move two symbols to the generic kconfigsRui Salvaterra2021-08-292-4/+0
| | | | | | | CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them to the generic kconfigs. And resort the generic kconfigs while at it. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: Askey RT4230W REV6: use usual writing for pcie partChukun Pan2021-08-251-3/+5
| | | | | | | | The problem has been fixed in f47cb405cafd ("ipq806x: fix pci broken on bootm command"), now the pcie part can be written in the usual way. Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: Askey RT4230W REV6: fix caldata scriptChukun Pan2021-08-241-2/+6
| | | | | | | | | | The partition name in the device dts is '0:ART'. Be independent to prevent this part from becoming incorrect once the kernel v5.4 gone. Fixes: da8428d277cd ("ipq806x: add support for Askey RT4230W REV6") Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
* ipq806x: fix min<>target opp-microvolt DTS mixupShane Synan2021-08-215-96/+105
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Rearrange all voltage triplets for "opp_table0" to match the specifications. "opp-microvolt" and "opp-microvolt-<name>" triplets are in order of <target min max>, and NOT <min target max>. Previously, the CPU would *always* spend its time at the "minimum" voltage, ignoring the actual intended target. This is a regression from previous behavior. On an NBG6817 with a Qualcomm CPU of PVS bin #2... (see &opp_table0 -> opp-1725000000 -> opp-microvolt-speed0-pvs2-v0) * Before: /usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_* ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <== 1260000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <== 1200000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <== 1140000 * After: /usr/bin/tail -n +1 /sys/kernel/debug/opp/cpu0/opp\:1725000000/supply-0/u_volt_* ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_max <== 1260000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_min <== 1140000 ==> /sys/kernel/debug/opp/cpu0/opp:1725000000/supply-0/u_volt_target <== 1200000 To check voltages and frequencies at run time, use... /bin/cat /sys/kernel/debug/regulator/regulator_summary && /bin/cat /sys/kernel/debug/clk/clk_summary | grep "hfpll" See https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/tree/Documentation/devicetree/bindings/opp/opp.txt?h=v5.4.142#n91 Fixes: 1e25423be8ac ("ipq806x: refresh dtsi patches") Signed-off-by: Shane Synan <digitalcircuit36939@gmail.com> Reviewed-by: Ansuel Smith <ansuelsmth@gmail.com> [commit message style cleanup, another kernel refresh] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-1911-26/+196
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* treewide: convert mtd-mac-address-increment* to generic implementationAnsuel Smith2021-07-193-4/+4
| | | | | | | | | | | | | Rework patch 681-NET-add-mtd-mac-address-support to implement only the function to read the mac-address from mtd. Generalize mtd-mac-address-increment function so it can be applied to any source of of_get_mac_address. Rename any mtd-mac-address-increment to mac-address-increment. Rename any mtd-mac-address-increment-byte to mac-address-increment-byte. This should make simplify the conversion of target to nvmem implementation. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* treewide: call check-size before append-metadataAdrian Schmutzler2021-07-101-1/+1
| | | | | | | | | | sysupgrade metadata is not flashed to the device, so check-size should be called _before_ adding metadata to the image. While at it, do some obvious wrapping improvements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ipq806x: fix dedicated cpufreq driverAnsuel Smith2021-06-304-34/+38
| | | | | | | | | 2 small fix for the dedicated cpufreq driver: - Fix index wrongly used as the current cpu - Exit early if a bad freq is detected. In the current state the freq is applied anyway even with invalid state. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix missing 1.4ghz cache freq for ipq8065 SoCAnsuel Smith2021-06-301-0/+11
| | | | | | | | With the new implementation of the dedicated cpufreq driver, the 1.4 Ghz was only dropped and not added to the ipq8065 SoC. Fix this to improve performance. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: fix missing changes in 5.4 for new cpufreq implementationAnsuel Smith2021-06-302-25/+57
| | | | | | | | | | The new cpufreq dedicated driver changed the node structure on how the cache should be defined in the dts. The 5.4 dtsi addition patch has not been updated to follow the new implementation. Fix this to restore correct cache scaling and restore any performance regression. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: refresh config for kernel 5.4John Audia2021-06-281-66/+2
| | | | | | | | | | * With kernel 5.4.128, ran: make kernel_menuconfig CONFIG_TARGET=generic * Manually added back CONFIG_LEDS_TRIGGER_DISK=y so as not to revert f93fcf8923aa ("ipq806x: enable disk-activity LED trigger") Signed-off-by: John Audia <graysky@archlinux.us> [minor commit title/message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix LAN and WAN port assignments on TP-Link AD7200Alex Henrie2021-06-061-1/+4
| | | | | | | | LAN port 4 was swapped with the WAN port and the remaining three LAN ports were numbered in reverse order from their labels on the case. Fixes: 1a775a4fd033 ("ipq806x: add support for TP-Link Talon AD7200") Signed-off-by: Alex Henrie <alexhenrie24@gmail.com>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-051-6/+6
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: add support for Askey RT4230W REV6Lauro Moreno2021-06-057-11/+333
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Askey RT4230W REV6 (Branded by Spectrum/Charter as RAC2V1K) At this time, there's no way to reinstall the stock firmware so don't install this on a router that's being rented. Specifications: Qualcomm IPQ8065 1 GB of RAM (DDR3) 512 MB Flash (NAND) 2x Wave 2 WiFi cards (QCA9984) 5x 10/100/1000 Mbps Ethernet (Switch: QCA8337) 1x LED (Controlled by a microcontroller that switches it between red and blue with different patterns) 1x USB 3.0 Type-A 12V DC Power Input UART header on PCB - pinout from top to bottom is RX, TX, GND, 5V Port settings are 115200n8 More information: https://forum.openwrt.org/t/askey-rac2v1k-support/15830 https://deviwiki.com/wiki/Askey_RAC2V1K To check what revision your router is, restore one of these config backups through the stock firmware to get ssh access then run "cat /proc/device-tree/model". https://forum.openwrt.org/t/askey-rac2v1k-support/15830/17 The revision number on the board doesn't seem to be very consistent so that's why this is needed. You can also run printenv in the uboot console and if machid is set to 177d, that means your router is rev6. Note: Don't install this if the router is being rented from an ISP. The defined partition layout is different from the OEM one and even if you changed the layout to match, backing up and restoring the OEM firmware breaks /overlay so nothing will save and the router will likely enter a bootloop. How to install: Method 1: Install without opening the case using SSH and tftp You'll need: RAC2V1K-SSH.zip: https://github.com/lmore377/openwrt-rt4230w/blob/master/RAC2V1K-SSH.zip initramfs and sysupgrade images Connect to one of the router's LAN ports Download the RAC2V1K-SSH.zip file and restore the config file that corresponds to your router's firmware (If you're firmware is newer than what's in the zip file, just restore the 1.1.16 file) After a reboot, you should be able to ssh into the router with username: "4230w" and password: "linuxbox" or "admin". Run the following commannds fw_setenv ipaddr 10.42.0.10 #IP of router, can be anything as long as it's in the same subnet as the server fw_setenv serverip 10.42.0.1# #IP of tftp server that's set up in next steps fw_setenv bootdelay 8 fw_setenv bootcmd "tftpboot initramfs.bin; bootm; bootipq" Don't reboot the router yet. Install and set up a tftp server on your computer Set a static ip on the ethernet interface of your computer (use this for serverip in the above commands) Rename the initramfs image to initramfs.bin, and host it with the tftp server Reboot the router. If you set up everything right, the router led should switch over to a slow blue glow which means openwrt is booted. If for some reason the file doesn't get loaded into ram properly, it should still boot to the OEM firmware. After openwrt boots, ssh into it and run these commands: fw_setenv bootcmd "setenv mtdids nand0=nand0 && setenv mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" fw_setenv bootdelay 2 After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Method 2: Install with serial access (Do this if something fails and you can't boot after using method 1) You'll need: initramfs and sysupgrade images Serial access: https://openwrt.org/inbox/toh/askey/askey_rt4230w_rev6#opening_the_case Install and set up a tftp server Set a static ip on the ethernet interface of your computer Download the initramfs image, rename it to initramfs.bin, and host it with the tftp server Connect the wan port of the router to your computer Interrupt U-Boot and run these commands: setenv serverip 10.42.0.1 (You can use whatever ip you set for the computer) setenv ipaddr 10.42.0.10 (Can be any ip as long as it's in the same subnet) setenv bootcmd "setenv mtdids nand0=nand0 && set mtdparts mtdparts=nand0:0x1A000000@0x2400000(firmware) && ubi part firmware && ubi read 0x44000000 kernel 0x6e0000 && bootm" saveenv tftpboot initramfs.bin bootm After openwrt boots up, figure out a way to get the sysupgrade file onto it (scp, custom build with usb kernel module included, wget, etc.) then flash it with sysupgrade. After it finishes flashing, it should reboot, the light should start flashing blue, then when the light starts "breathing" blue that means openwrt is booted. Signed-off-by: Lauro Moreno <lmore377@gmail.com> [add entry in 5.10 patch, fix whitespace issues] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix warning about tsens debugfs already registeredAnsuel Smith2021-05-232-0/+95
| | | | | | Backport a pending patch already reviewed that fix some warning about tsens debugs already registered. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: reduce pci IO space to 64kAnsuel Smith2021-05-232-25/+46
| | | | | | | | | With some talk with the ARM maintainer, it was notice that enlarging the limit to the current value is VERY wrong and clash with other memory. A better solution would be to reduce the IO space from 1MB to 64K as probably it's a long lasting typo and even x86 arch doesn't have a IO space that big. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.4 to 5.4.120John Audia2021-05-231-1/+1
| | | | | | | | | | | | | | | Removed upstreamed: generic/pending-5.4/770-02-net-ethernet-mtk_eth_soc-fix-rx-vlan-offload.patch All other patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Note that since I rebased the previous commit, I removed my Run-tested line although I confirm building the image successfully. Signed-off-by: John Audia <graysky@archlinux.us>
* kernel: bump 5.10 to 5.10.38Rui Salvaterra2021-05-223-106/+7
| | | | | | | | | | | | | | | | | | Automatically refreshed: apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch generic/backport-5.10/610-v5.13-31-net-ethernet-mtk_eth_soc-fix-parsing-packets-in-GDM.patch generic/backport-5.10/610-v5.13-32-net-ethernet-mtk_eth_soc-add-support-for-initializin.patch generic/backport-5.10/610-v5.13-33-net-ethernet-mtk_eth_soc-add-flow-offloading-support.patch generic/hack-5.10/204-module_strip.patch generic/hack-5.10/911-kobject_add_broadcast_uevent.patch ipq806x/patches-5.10/104-1-drivers-thermal-tsens-Add-VER_0-tsens-version.patch ipq806x/patches-5.10/104-8-drivers-thermal-tsens-Add-support-for-ipq8064-tsens.patch Deleted (reverse-appliable): generic/backport-5.10/610-v5.13-37-net-ethernet-mtk_eth_soc-fix-RX-VLAN-offload.patch ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.37Rui Salvaterra2021-05-142-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Automatically refreshed: ath79/patches-5.10/0032-MIPS-ath79-sanitize-symbols.patch bcm63xx/patches-5.10/322-MIPS-BCM63XX-switch-to-IRQ_DOMAIN.patch bcm63xx/patches-5.10/434-nand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch bmips/patches-5.10/001-v5.11-mips-bmips-select-ARCH_HAS_RESET_CONTROLLER.patch bmips/patches-5.10/041-v5.13-mtd-rawnand-brcmnand-fix-OOB-R-W-with-Hamming-ECC.patch bmips/patches-5.10/202-mips-bmips-disable-ARCH_HAS_SYNC_DMA_FOR_CPU_ALL.patch bmips/patches-5.10/600-mips-bmips-add-pci-support.patch generic/backport-5.10/103-v5.13-MIPS-select-CPU_MIPS64-for-remaining-MIPS64-CPUs.patch generic/hack-5.10/301-mips_image_cmdline_hack.patch generic/hack-5.10/402-mtd-blktrans-call-add-disks-after-mtd-device.patch generic/hack-5.10/902-debloat_proc.patch generic/pending-5.10/300-mips_expose_boot_raw.patch generic/pending-5.10/495-mtd-core-add-get_mtd_device_by_node.patch generic/pending-5.10/630-packet_socket_type.patch ipq806x/patches-5.10/0072-add-ipq806x-with-no-clocks.patch ipq806x/patches-5.10/099-1-mtd-nand-raw-qcom_nandc-add-boot_layout_mode-support.patch lantiq/patches-5.10/0001-MIPS-lantiq-add-pcie-driver.patch lantiq/patches-5.10/0023-NET-PHY-add-led-support-for-intel-xway.patch lantiq/patches-5.10/0152-lantiq-VPE.patch Deleted (reverse-appliable): bmips/patches-5.10/052-v5.13-gpio-guard-gpiochip_irqchip_add_domain-with-GPIOLIB_.patch generic/backport-5.10/499-v5.13-mtd-don-t-lock-when-recursively-deleting-partitions.patch Deleted (alternative upstream fix): ramips/patches-5.10/330-fix-pci-init-mt7620.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.36Rui Salvaterra2021-05-143-5/+5
| | | | | | | | | | | | | | | | | | | | | Automatically refreshed: apm821xx/patches-5.10/802-usb-xhci-force-msi-renesas-xhci.patch ath79/patches-5.10/410-spi-ath79-Implement-the-spi_mem-interface.patch bcm63xx/patches-5.10/143-gpio-fix-device-tree-gpio-hogs-on-dual-role-gpio-pin.patch generic/pending-5.10/465-m25p80-mx-disable-software-protection.patch ipq806x/patches-5.10/0069-arm-boot-add-dts-files.patch ipq806x/patches-5.10/101-dwmac-ipq806x-qsgmii-pcs-all-ch-ctl.patch ipq806x/patches-5.10/106-5.13-net-stmmac-Set-FIFO-sizes-for-ipq806x.patch Deleted (empty or reverse-appliable): ath79/patches-5.10/411-spi-ath79-add-SPI_MASTER_GPIO_SS-flag.patch ath79/patches-5.10/0050-spi-ath79-remove-spi-master-setup-and-cleanup-assign.patch ath79/patches-5.10/0054-spi-sync-up-initial-chipselect-state.patch Manually refreshed: ath79/patches-5.10/0033-spi-ath79-drop-pdata-support.patch Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq806x: base-files: asrock: fix bootcount includePetr Štetiar2021-05-131-5/+2
| | | | | | | | | | | | | | | | | | | | | Fixes following error while executing the init script on the buildhost: Enabling boot ./etc/init.d/bootcount: line 5: /lib/upgrade/asrock.sh: No such file or directory Enabling bootcount While at it fix following shellcheck issue: base-files/etc/init.d/bootcount line 11: if [ $? -eq 0 ]; then ^-- SC2181: Check exit code directly with e.g. 'if mycmd;', not indirectly with $?. Cc: Ansuel Smith <ansuelsmth@gmail.com> Cc: Pawel Dembicki <paweldembicki@gmail.com> Cc: Christian Lamparter <chunkeey@gmail.com> Fixes: 98b86296e67d ("ipq806x: add support for ASRock G10") References: https://gitlab.com/ynezz/openwrt/-/jobs/1243290743#L1444 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.10 to 5.10.35Kevin Darbyshire-Bryant2021-05-0914-96/+44
| | | | | | | | | | Refresh kernel patches. Built under MacOS Run tested: x86_64 (apu2) Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ipq806x: Bring missing patches from 5.4 to 5.10Mark Mentovai2021-05-092-0/+119
| | | | | | | | | | | | | | Kernel 5.10 support for ipq806x was added at the same time that these patches were developed for kernel 5.4. This carries the patches forward to kernel 5.10. fa731838c524 ipq806x: dwmac: clear forced speed during probe 75ca641f1b84 ipq806x: Add "snps,dwmac" to all gmac compatible= d62825dd77b3 ipq806x: dwmac: set forced speed when using fixed-link Signed-off-by: Mark Mentovai <mark@moxienet.com> Run-tested: ipq806x/ubnt,unifi-ac-hd Cc: Ansuel Smith <ansuelsmth@gmail.com>
* ipq806x: Add mising devices to kernel 5.10Mark Mentovai2021-05-091-1/+6
| | | | | | | | | | | | | | d53be2a2e981 migrated 0069-arm-boot-add-dts-files.patch from patches-5.4 to patches-5.10, but a subsequent patch in that set, 1e25423be8ac, erroneously removed several devices: ipq8062/nec,wg2600hp3 from 3bb16185737c ipq8064/asrock,g10 from 98b86296e67d ipq8064/ubnt,unifi-ac-hd from 4e46beb31342 Signed-off-by: Mark Mentovai <mark@moxienet.com> Run-tested: ipq806x/ubnt,unifi-ac-hd Cc: Ansuel Smith <ansuelsmth@gmail.com>
* kernel: bump 5.4 to 5.4.117John Audia2021-05-093-30/+10
| | | | | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us>
* ipq806x: ecw5410: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-082-4/+20
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: g10: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-082-3/+15
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: nbg6817: case-insensitive qcom-smem partitionsStefan Lippers-Hollmann2021-05-083-6/+24
| | | | | | | | The out-of-tree qcom-smem patches traditionally displayed mtd partition names in upper case, starting with the new mainline qcom-smem support in kernel v5.10, it switches to normalizing the partition names to lower case. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-31 17:58:41 +0000