aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x
Commit message (Collapse)AuthorAgeFilesLines
* ipq8065: adjust SS USB PHY power settingsPavel Kubelun2018-01-171-0/+11
| | | | | | | | | | | According to QSDK ipq8065 has different SS USB PHY power settings. Adjust it according to QSDK settings. It also corresponds to oem Netgear R7800 tarball for soc ver >= 2. https://github.com/paul-chambers/netgear-r7800/blob/eeac2e10190f6f45e32e4c7012c4babc351898d8/git_home/linux.git/sourcecode/arch/arm/mach-msm/board-ipq806x.c#L2494 Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: add phy 1 master reset controlPavel Kubelun2018-01-172-12/+26
| | | | | | | In current state only phy 0 master reset is controlled. Add the phy 1 reset. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: usb: Control USB master resetPavel Kubelun2018-01-172-0/+67
| | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=eggplant&id=a86bda9f8a7965f0cedd347a9c04800eb9f41ea3 Commit message: "During removal of the glue layer(dwc3-of-simple), USB master reset is set to active and during insertion it is de-activated." Change-Id: I537dc810f6cb2a46664ee674840145066432b957 Signed-off-by: Vasudevan Murugesan <vmuruges@codeaurora.org> (cherry picked from commit 4611e13580a216812f85f0801b95442d02eeb836)" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: dwc3: Fix power_on and power_off sequencePavel Kubelun2018-01-171-29/+58
| | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=d316437c9cdb70023a760342678f32e27241725a The commit fixes: - dwc3 phy module unloading - possibly fixes FS#177 when some devices were improperly enumerated as HS while being SS thus stucking the driver during boot. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: Update HSIO recommended usb phy settingsPavel Kubelun2018-01-171-15/+77
| | | | | | | | | | | | | | | | Picking commit from QSDK https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/drivers/phy/phy-qcom-dwc3.c?h=eggplant&id=cf82fdf4bdd081cd81bb081f7815b915bc8bb851 The comit adjusts USB dwc3 phy default values as per QSDK recomendation and allows to set it through DT. Commit message: "SoC version based values will be recovered from the device node. If device node does not have such values, defaults are applied. Change-Id: Ia77b5b7fe95ce1a433885df1761091bced98d989 Signed-off-by: Gokul Sriram Palanisamy <gpalan@codeaurora.org>" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* Revert "ipq8064: Fix dwc3 module unloading"Pavel Kubelun2018-01-171-11/+3
| | | | | | | | Preparing for proper fixes thus reverting commits: - 8db079a9ff1756059250b801617a20baba214684 "ipq8064: Fix dwc3 module unloading" - c75f059b0c4d09dd0da60e14c4933a9f645266d1 "ipq8064: Fix dwc3 module unloading" Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: update clk and cpufreq driversPavel Kubelun2018-01-1716-814/+388
| | | | | | | | | | | | | A newer clk and cpufreq drivers for ipq806x platform had been sent upstream. A change that i have noticed is that now it's possible to set min, cur and max frequencies from sysfs (previously it was bugged and caused nothing). Following patches are removed: - 0036-clk-Avoid-sending-high-rates-to-downstream-clocks-du.patch - seems it was dropped from the patchset by current committer. - 0044-clk-qcom-krait-Remove-CLK_IS_ROOT.patch - already applied to the driver itself in the corresponding patch. - 0057-clk-qcom-Add-regmap-mux-div-clocks-support.patch - seem to be irrelevant to ipq806x. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: force 2nd pci slot into gen1 modePavel Kubelun2018-01-1710-13/+17
| | | | | | | | | | | | | | According to QSDK and OEM tarballs (checked c2600, r7500v2, r7800) 2nd pci slot (pci1, 2,4 GHz card)) on ap148 based boards should operate in gen1 mode. EA8500 is an exception and according to GPL pcie0 should operate in gen1 mode. In previous commit we've added the support for this option, so enable it in DT for affected devices. QSDK ref: https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=f3b07fe309027c52fc163149500cedddd707c506 While at it move the phy transmit termination offset value into dtsi file as it's platform specific. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix wireless regressionPavel Kubelun2018-01-1710-308/+734
| | | | | | | | | | | | | | | | In current state there's huge regression on ipq806x target that causes the device to transmit broken/malformed frames that are not corrected/detected by error control mechanisms and other less severe issues. https://bugs.lede-project.org/index.php?do=details&task_id=1197 This finally had been narrowed down to patch 0071-pcie-qcom-fixes.patch Meanwhile QSDK contains a handful of commits that add support for ipq806x to upstream qcom pcie driver https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/log/drivers/pci/host/pcie-qcom.c?h=eggplant Unfortunately qca developers do not bother to push it upstream. Using those commits instead of lede 0071 patch fixes mentioned issue and probably many others as it seems that corrupted data has been originating within pcie misconfiguration. Fixes: FS#1197 and probably others Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: drop ubifs supportMathias Kresin2018-01-152-10/+1
| | | | | | | | Ubifs is disabled for all boards except the evaluation boards and the Fritz!Box 4040 anyway. According the author, the ubifs support for the Fritz!Box 4040 wasn't enabled on purpose. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop legacy image leftoversMathias Kresin2018-01-151-24/+0
| | | | | | | Remove leftover code used for legacy images. There are no relevant binary differences for the images after removing the legacy leftovers. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: unset filesystem specific build command by defaultMathias Kresin2018-01-151-0/+1
| | | | | | | | | | | | | Initialise the filesystem specific build command. Otherwise it will be unintended inherit to following images and will cause a wrong image format. The issue is around for ages but was only recently triggered due to the added support for the Openmesh a42. Fixes: FS#1276 Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: remove unnecessary filesystem specific buildMathias Kresin2018-01-151-1/+1
| | | | | | The Openmesh factory image doesn't need a squashfs specific build command. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: use bin file extension for sysupgrade-tar imagesMathias Kresin2018-01-151-8/+8
| | | | | | | Use the file extension bin for sysupgrade-tar images to unify the file extension across the target/tree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-137-1/+388
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: enable gpio watchdog supportSven Eckelmann2018-01-131-0/+2
| | | | | | | | | The kernel driver gpio-wdt or the userspace tool om-watchdog can be used to trigger external gpio watchdog chips. The gpio-wdt driver has the benefit that it can be configured together with the rest of the device in the DTS and better integrates in the OpenWrt via procd. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-136-170/+169
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-1310-153/+87
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: sync image filename with dt compatible stringLuis Araneda2018-01-131-28/+28
| | | | | | | Use <manufacturer>_<modelname> as image name for board using the devicetree compat string as boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add a helper variable with the vendor name strippedLuis Araneda2018-01-131-0/+1
| | | | | | | | | | This will allow to maintain the current syntax for LEDs config when switching to a device tree compatible string boardname. None of the current boards use a comma in the boardname, so they will be unaffected. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: add missing dt compatible string to ap-dk04 boardLuis Araneda2018-01-131-1/+2
| | | | | | Compatible string is mandatory to dts files Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: drop partitial supported boardsMathias Kresin2018-01-134-364/+1
| | | | | | | | | There are only artifacts for these boards in our tree and not even partial support. Drop teh stale files. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.9 to 4.9.75Kevin Darbyshire-Bryant2018-01-101-2/+2
| | | | | | | | | | | | | Refresh patches Fixes: CVE-2017-5754 aka Meltdown Tested-on: ar71xx Archer C7 v2 Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Koen Vandeputte <koen.vandeputte@ncentric.com> [fix conflict after 4.14 bump] Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq806x: drop kernel 4.4 leftoversMathias Kresin2018-01-0910-3628/+0
| | | | | | | | Remove the kernel 4.4 specific devicetree source files. Fixes: 3a3564ead5e4 ("ipq806x: remove v4.4 support") Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: unify get_dt_led helper functionChristian Lamparter2017-12-142-17/+4
| | | | | | | | | | | | | | Lantiq and IPQ806X (which includes IPQ40XX) both define the same custom function {ipq806x|lantiq}_get_dt_led. This patch moves the function into the base-file package at lib/functions/leds.sh to make it more accessible for other targets as well. Cc: Mathias Kresin <dev@kresin.me> Cc: John Crispin <john@phrozen.org> Cc: Hannu Nyman <hannu.nyman@iki.fi> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: add only one device when appending to TARGET_DEVICESLuis Araneda2017-12-121-3/+14
| | | | | | | | | This will avoid some conflicts when doing a git rebase or merge, specially when adding support to a new device. Signed-off-by: Luis Araneda <luaraneda@gmail.com> [drop brcm47xx changes which rename the images] Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.9 to 4.9.67Stijn Tintel2017-12-071-1/+1
| | | | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - generic/190-1-5-e1000e-Fix-error-path-in-link-detection.patch - generic/190-3-5-e1000e-Fix-return-value-test.patch - generic/190-4-5-e1000e-Separate-signaling-for-link-check-link-up.patch - generic/190-5-5-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - ramips/0102-MIPS-ralink-Fix-MT7628-pinmux.patch - ramips/0103-MIPS-ralink-Fix-typo-in-mt7628-pinmux-function Update patches that no longer apply: - layerscape/815-spi-support-layerscape.patch - ramips/0099-pci-mt7620.patch Compile-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Runtime-tested on ar71xx, brcm2708/bcm2708, octeon and x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.9 to 4.9.63Koen Vandeputte2017-11-221-1/+1
| | | | | | | | | | | Refreshed all patches. Removed upstreamed parts. Compile-tested: cns3xxx, imx6, mvebu, layerscape Run-tested: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: ipq4019: enable usb phyRoman Yeryomin2017-11-171-1/+1
| | | | | | Run tested on ap-dk01.2-c1 Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ip806x: nbg6817: sysupgrade support both targets for kernel/ rootfs partitionsStefan Lippers-Hollmann2017-10-291-1/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | With this commit and the previous "nbg6817: don't hardcode the rootfs location by using append-rootblock instead" applied, it is possible to boot- and sysupgrade from both dual-boot sets (the primary mmcblk0p4+mmcblk0p5 or the alternative mmcblk0p7+mmcblk0p8). However the sysupgrade support does not toggle between both dual-boot sets between firmware upgrades so far. The partition map of the eMMC used in the nbg6817 is: Found valid GPT with protective MBR; using GPT. Disk /dev/mmcblk0: 7471104 sectors, 3.6 GiB Logical sector size: 512 bytes Disk identifier (GUID): XXX Partition table holds up to 12 entries First usable sector is 34, last usable sector is 7471070 Partitions will be aligned on 2-sector boundaries Total free space is 1 sectors (512 bytes) Number Start (sector) End (sector) Size Code Name 1 34 8225 4.0 MiB FFFF rootfs_data 2 8226 16417 4.0 MiB FFFF romd 3 16418 18465 1024.0 KiB FFFF header 4 18466 26657 4.0 MiB FFFF kernel 5 26658 157729 64.0 MiB FFFF rootfs 6 157730 159777 1024.0 KiB FFFF header_1 7 159778 167969 4.0 MiB FFFF kernel_1 8 167970 299041 64.0 MiB FFFF rootfs_1 9 299042 823329 256.0 MiB FFFF bu1 10 823330 7471069 3.2 GiB FFFF bu2 rootfs_data is the ext4 formatted overlay of the OEM firmware, LEDE ignores it due to its (too) small size. romd/ bu1 are initialized with zeroes (0x00) and unused. bu2 is formatted with ext4 and used for streamboost and other optional functionality by the OEM firmware, it is reformatted during factory resets of the OEM firmware. header/ header_1 contains version information for the corresponding vendor firmwares installed to kernel/rootfs or kernel_1/ rootfs_1, the format hasn't been completely reverse engineered so far and remains left untouched by LEDE: V1.00(ABCS.2)C0: 00000000 00 00 a7 74 01 32 f0 00 56 31 2e 30 30 28 41 42 |...t.2..V1.00(AB| 00000010 43 53 2e 32 29 43 30 00 ff ff ff ff ff ff ff ff |CS.2)C0.........| 00000020 ff ff ff ff ff ff ff ff 00 00 d5 dc 4e 42 47 36 |............NBG6| 00000030 38 31 37 00 ff ff ff ff ff ff ff ff ff ff ff ff |817.............| 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000060 ff ff ff ff ff ff ff ff ff ff ff ff 00 00 22 a3 |..............".| 00000070 00 1c 70 00 ff ff ff ff ff ff ff ff ff ff ff ff |..p.............| 00000080 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000800 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00100000 V1.00(ABCS.5)C0: 00000000 00 00 bf 94 01 46 d8 00 56 31 2e 30 30 28 41 42 |.....F..V1.00(AB| 00000010 43 53 2e 35 29 43 30 00 ff ff ff ff ff ff ff ff |CS.5)C0.........| 00000020 ff ff ff ff ff ff ff ff 00 00 d6 5a 4e 42 47 36 |...........ZNBG6| 00000030 38 31 37 00 ff ff ff ff ff ff ff ff ff ff ff ff |817.............| 00000040 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00000060 ff ff ff ff ff ff ff ff ff ff ff ff 00 00 c0 2c |...............,| 00000070 00 1c 58 00 ff ff ff ff ff ff ff ff ff ff ff ff |..X.............| 00000080 ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff ff |................| * 00010000 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 |................| * 00100000 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ip806x: nbg6817: don't hardcode the rootfs location by using ↵Stefan Lippers-Hollmann2017-10-291-1/+2
| | | | | | | | | | | | | | | | | | | append-rootblock instead This changes the cmdline from: Kernel command line: root=/dev/mmcblk0p5 rootfstype=squashfs,ext4 rootwait noinitrd Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) to Kernel command line: rootfstype=squashfs,ext4 rootwait noinitrd root=/dev/mmcblk0p5 Bootloader command line (ignored): board=NBG6817 root=/dev/mmcblk0p5 rootwait zld_ver=2.04 console=ttyHSL1,115200n8 mtdparts=m25p80:0xC0000(SBL)ro,0x40000(TZ)ro,0x40000(RPM)ro,0x80000(u-boot)ro,0x10000(env)ro,0x10000(ART)ro,0x10000(dualflag),0x210000(reserved) As a consequence booting from the alternative dual-boot partition set (root=/dev/mmcblk0p8) becomes possible. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: ipq4019: add ap-dk01.1-c1 board supportRoman Yeryomin2017-10-305-1/+151
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | AP-DK01.1-C1 is QCA dev board with: - ipq4018 quad core ARM @716.8MHz, 2x2 dual (11n+11ac) radio - 256MB RAM - 32MB SPI flash - QCA8075 multiport ethernet phy (WAN port, 4x LAN ports) First installation via u-boot: sf probe sf erase 0x180000 0x1a00000 tftpboot 0x84000000 lede-ipq806x-AP-DK01.1-C1-squashfs-sysupgrade.bin sf write 0x84000000 0x180000 $filesize Further upgrades via sysupgrade. Changes: - add partitions - set memory size to 256MB - add reserved memory mapping - add correct compatible string - add image generation - extract pre-cal data from ART partition Compile and run tested. Wirespeed NAT can be achieved with spreading rx interrupts over different cores. Wifi speed is ~550Mbps @5GHz in open air. Note: AP-DK01.1-C1 is fully compatible with AP-DK01.2-C1, which has ipq4028 instead of ipq4018 on board. Changes since v2: - based on dts(i) rework/cleanup submitted: http://lists.infradead.org/pipermail/lede-dev/2017-October/009596.html - precise reserved memory mapping - more precise description - compatible string Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: fix maximum cpu speedRoman Yeryomin2017-10-302-9/+13
| | | | | | | | Supported frequencies of all ipq40xx chips are 48, 200, 500 and 716.8 MHz. Previous 666MHz setting was most likely related to instability of early chips/boards made before mass production. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: remove spi chip node from ap-dk01 dtsiRoman Yeryomin2017-10-304-20/+17
| | | | | | All ap-dk01 boards have different spi chips, thus no point in keeping it in dtsi. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: move ap-dk01 networking entries to dtsiRoman Yeryomin2017-10-304-70/+32
| | | | | | That is mdio/ethernet and wifi are present on all ap-dk01 boards. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: remove counter entry from ap-dk01 boardsRoman Yeryomin2017-10-303-15/+0
| | | | | | There is no code implementing "qcom,qca-gcnt", so no point in keeping it. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: move ap-dk01 tcsr nodes to dtsiRoman Yeryomin2017-10-304-85/+42
| | | | | | tcsr configuration is the same for all ap-dk01 boards Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: remove crypto nodes from board dtsRoman Yeryomin2017-10-303-24/+0
| | | | | | | | | crypto and cryptobam are already present in dtsi used by these boards: - fritz4040 - nbg6617 - rt-ac58u Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: move xo and timer nodes to SoC dtsiRoman Yeryomin2017-10-302-0/+105
| | | | | | xo and timer are common thing and it makes more sense to keep them in SoC dtsi Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: ipq4019: dts: fix pinctrl node nameRoman Yeryomin2017-10-303-1/+56
| | | | Signed-off-by: Roman Yeryomin <roman@advem.lv>
* ipq806x: nbg6817: sync MAC addresses to the upstream valuesStefan Lippers-Hollmann2017-11-032-2/+5
| | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 calculates all MAC addresses based on the ethaddr value stored in the U-Boot environment (0:APPSBLENV). No MAC addresses are stored in the ART partition and the generated MAC addresses for the wlan interfaces alternate randomly between 12:34:56:78:90:12 and 00:03:7f:12:34:56. interface new/ OEM MAC old MAC wlan-2.4g (phy1): ethaddr undefined wlan-5g (phy0): ethaddr + 1 undefined lan : ethaddr + 2 ethaddr wan : ethaddr + 3 ethaddr + 1 This patch defines stable MAC addresses for the wlan interfaces for the first time instead of generating them at random. The previously defined values for lan/ wan are changed to follow the settings of the OEM firmware. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: nbg6817: add kmod-fs-ext4 to device packagesStefan Lippers-Hollmann2017-11-031-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | The ZyXEL NBG6817 uses an eMMC flash for the rootfs, which is split into the readonly squashfs and ext4 for the overlay. This adds the required package to the device packages to allow mounting the overlay by default. /dev/root on /rom type squashfs (ro,relatime) proc on /proc type proc (rw,nosuid,nodev,noexec,noatime) sysfs on /sys type sysfs (rw,nosuid,nodev,noexec,noatime) tmpfs on /tmp type tmpfs (rw,nosuid,nodev,noatime) /dev/loop0 on /overlay type ext4 (rw,noatime,data=ordered) overlayfs:/overlay on / type overlay (rw,noatime,lowerdir=/,upperdir=/overlay/upper,workdir=/overlay/work) tmpfs on /dev type tmpfs (rw,nosuid,relatime,size=512k,mode=755) devpts on /dev/pts type devpts (rw,nosuid,noexec,relatime,mode=600,ptmxmode=000) debugfs on /sys/kernel/debug type debugfs (rw,noatime) mountd(pid1040) on /tmp/run/blockd type autofs (rw,relatime,fd=7,pgrp=1,timeout=30,minproto=5,maxproto=5,indirect) Before this commit, the ext4 based overlayfs could not be mounted, which left only the tmpfs based/ volatile emergency overlay in place. Fixes: https://forum.lede-project.org/t/zyxel-nbg6817-flashing-from-oem/768 Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* treewide: do not use IMG_PREFIX in Image/PrepareJonas Gorski2017-10-261-2/+2
| | | | | | | | | | | | | | IMG_PREFIX can be modified in ImageBuilder by passing EXTRA_IMAGE_NAME on command line, but Image/Prepare is not run in ImageBuilder. This causes missing files when IMG_PREFIX is used for target file names in Image/Prepare, then as source file names in Image/BuildKernel or Image/Build. Fix this by using a fixed output file name in Image/Prepare, and copy to the expected file name in Image/BuildKernel instead, which is run by ImageBuilder. Signed-off-by: Jonas Gorski <jonas.gorski@gmail.com>
* ipq806x: fix Zyxel NBG6817 WiFi buttonTolga Cakir2017-10-251-2/+3
| | | | | | | | Zyxel NBG6817 features a WiFi button, which becomes functional by setting correct GPIO. It is a switch-type button, so it emits KEY_RFKILL on each ON and OFF state. This is achieved by setting input-type to EV_SW. Signed-off-by: Tolga Cakir <tolga@cevel.net>
* kernel: bump 4.9 to 4.9.58Stijn Tintel2017-10-231-2/+2
| | | | | | | | Refresh patches. Compile-tested: ar71xx, octeon, x86/64. Runtime-tested: octeon, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: update 4.9 to 4.9.50Stijn Tintel2017-09-182-72/+64
| | | | | | | | | | | | Refresh patches. Compile-tested on ipq8065/nbg6817 and x86/64. Runtime-tested on ipq8065/nbg6817 and x86/64. Fixes CVE-2017-1000251. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be> [adapt qcom_nandc.c patches to match upstream changes, test ipq8065/nbg6817] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: Archer C2600: fix switch ports numberingBaptiste Jonglez2017-08-241-1/+4
| | | | | | | The order of LAN ports shown in Luci is reversed compared to what is written on the case of the device. Fix the order so that they match. Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* kernel: update 4.9 to 4.9.44Stijn Tintel2017-08-173-3/+3
| | | | | | | | | | | | | | | Refresh patches. Adapt 704-phy-no-genphy-soft-reset.patch. Remove brcm2708/950-0005-mm-Remove-the-PFN-busy-warning.patch. Compile-tested on brcm2708/bcm2708 and x86/64. Runtime-tested on brcm2708/bcm2708 and x86/64. Fixes the following vulnerabilities: - CVE-2017-7533 - CVE-2017-1000111 - CVE-2017-1000112 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* treewide: use only board_name function to get nameMathias Kresin2017-07-151-1/+1
| | | | | | | | | | | | Do not parse /tmp/sysinfo/board_name, /proc/cpuinfo or the device tree compatible string directly. Always use the board_name function to get the board name. The admswconfig package still reads /proc/cpuinfo directly. The code looks somehow broken and the whole adm5120 which uses this package looks unmaintained. Leave it as it is for now. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: drop target board_name functionsMathias Kresin2017-07-151-9/+0
| | | | | | They are not used any longer. Signed-off-by: Mathias Kresin <dev@kresin.me>