aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/patches-4.14
Commit message (Collapse)AuthorAgeFilesLines
* kernel: bump 4.14 to 4.14.172Koen Vandeputte2020-03-094-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.171Koen Vandeputte2020-02-241-1/+1
| | | | | | | | | | | | Refreshed all patches. Fixes: - CVE-2013-1798 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: fix bug in L2 cache scalingAnsuel Smith2020-02-231-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It has been notice a buf in L2 cache scaling where the scaling is not done proprely if the frequency is set to the initial state before the new frequency. From: https://patchwork.kernel.org/patch/10565443/ * The clocks are set to aux clock rate first to make sure the * secondary mux is not sourcing off of QSB. The rate is then set to * two different rates to force a HFPLL reinit under all * circumstances. In the initial stage of boot to force a new frequency to apply, is needed to first set the frequency back to the lowest one (aux_rate) and then to the target one. This force and make sure the controller actually switch the frequency to the right one. Apply the same mechanism to L2 frequency scaling. Before scaling to the target frequency, first set the frequency to the aux_rate to force the transition, then scale it to the target frequency. Doing the wrong way can produce unexpected results and could lock the scaling mechanism until a full reboot is done (Causing a full reset by the krait-cc driver) From: https://git.kernel.org/pub/scm/linux/kernel/git/next/linux-next.git/commit/?id=77612720a2362230af726baa4149c40ec7a7fb05 When the Hfplls are reprogrammed during the rate change, the primary muxes which are sourced from the same hfpll for higher frequencies, needs to be switched to the 'safe secondary mux' as the parent for that small window. This is done by registering a clk notifier for the muxes and switching to the safe parent in the PRE_RATE_CHANGE notifier and back to the original parent in the POST_RATE_CHANGE notifier. This should apply also to L2 scaling... as we can't relly use the notifier, we manually do this on L2 scaling. Tested-By: Marc Benoit <marcb62185@gmail.com> [19.07: R7800] Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> [nbg6817/ipq8065] Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com> (cherry picked from commit 5ab9c0b388e9cf2537ef23d6e9baaf5730a14a1c)
* kernel: bump 4.14 to 4.14.159Koen Vandeputte2019-12-241-3/+3
| | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 302-0002-dmaengine-dw-implement-per-channel-protection-contro.patch Fixes: - CVE-2019-19332 Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.158Koen Vandeputte2019-12-101-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 400-mtd-add-rootfs-split-support.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.156Koen Vandeputte2019-11-294-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.155Koen Vandeputte2019-11-224-5/+5
| | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 707-dpaa-ethernet-support-layerscape.patch Remove upstreamed: - 034-v4.20-MIPS-BCM47XX-Enable-USB-power-on-Netgear-WNDR3400v3.patch - 001-4.21-01-BCM63XX-fix-switch-core-reset-on-BCM6368.patch - 073-qcom-ipq4019-fix-cpu0-s-qcom-saw2-reg-value.patch Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.154Koen Vandeputte2019-11-191-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 902-debloat_proc.patch - 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch - 807-usb-support-layerscape.patch - 809-flexcan-support-layerscape.patch - 816-pcie-support-layerscape.patch Remove upstreamed: - 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch New symbols: X86_INTEL_MPX X86_INTEL_MEMORY_PROTECTION_KEYS CONFIG_X86_INTEL_TSX_MODE_OFF X86_INTEL_TSX_MODE_ON X86_INTEL_TSX_MODE_AUTO SGL_ALLOC Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.120Koen Vandeputte2019-05-211-2/+2
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 103-MIPS-perf-ath79-Fix-perfcount-IRQ-assignment.patch - 060-fix-oxnas-rps-dt-match.patch Altered patches: - 0067-generic-Mangle-bootloader-s-kernel-arguments.patch - 006-mvebu-Mangle-bootloader-s-kernel-arguments.patch - 996-generic-Mangle-bootloader-s-kernel-arguments.patch Compile-tested on: ar71xx, cns3xxx, imx6, mvebu, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.108Koen Vandeputte2019-03-271-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 950-0033-i2c-bcm2835-Add-debug-support.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.102Koen Vandeputte2019-02-221-1/+1
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch Remove upstreamed hunks: - 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch Fixes: - CVE-2018-1000026 Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.99Koen Vandeputte2019-02-143-4/+4
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 950-0434-mmc-bcm2835-Recover-from-MMC_SEND_EXT_CSD.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.91Koen Vandeputte2019-01-071-1/+1
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: add support for Buffalo WXR-2533DHPINAGAKI Hiroshi2019-01-011-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
* kernel: bump 4.14 to 4.14.86Koen Vandeputte2018-12-101-23/+19
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: Add support for IPQ8064 AP161 boardRam Chandra Jangir2018-11-261-1/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU - RAM: 512MB DDR3 System Memory - NOR Flash: 32MB SPI NOR - NAND Flash: 256MB NAND - Ethernet: 5 x 1G via QCA8337N - USB: 2 x USB 3.0 SuperSpeed - PCIe: 3x Mini PCIe 2.0 Slots Three PCIE2.0 connectors can connect two or three radio cards such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN How to flash via u-boot console: tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin nand erase 0x1340000 0x4000000 nand write 0x44000000 0x1340000 $filesize setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’ saveenv bootm Further upgrades via sysupgrade. Tested on IPQ8064 AP161 Board: 1) NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ipq8064: pinctrl: Fixed missing RGMII pincontrol definitionsRam Chandra Jangir2018-11-261-0/+54
| | | | Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* kernel: bump 4.14 to 4.14.81Koen Vandeputte2018-11-144-19/+16
| | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed patches: - 081-spi-bcm-qspi-switch-back-to-reading-flash-using-smal.patch Altered patches: - 0054-cpufreq-dt-Handle-OPP-voltage-adjust-events Compile-tested on: cns3xxx, imx6, ipq806x, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.79Koen Vandeputte2018-11-051-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.74Koen Vandeputte2018-10-041-8/+8
| | | | | | | | | | | | | Refreshed all patches. Fixes CVE: - CVE-2018-7755 Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-261-3/+3
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch - 0013-MIPS-ath79-fix-system-restart.patch - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.67Koen Vandeputte2018-08-281-1/+1
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed patches: - 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq806x: drop gpio export patchMathias Kresin2018-06-281-166/+0
| | | | | | The hack isn't used by any board. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.51Kevin Darbyshire-Bryant2018-06-262-9/+9
| | | | | | | | | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Refresh patches. Remove patch that can be reverse applied: mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch Update patch that no longer applied: ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch Compiled-tested-for: lantiq, ramips Run-tested-on: lantiq BT hh5a, ramips MIR3g Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Michael Yartys <michael.yartys@protonmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-191-7/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* kernel: bump 4.14 to 4.14.43Koen Vandeputte2018-05-2451-844/+847
| | | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Michael Yartys <michael.yartys@protonmail.com>
* ipq806x: drop "mtd: nand: add Winbond manufacturer and chip"Stefan Lippers-Hollmann2018-05-221-38/+0
| | | | | | The W25N01GV NAND is currently not used in any ipq806x device. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* kernel: iqp806x low latency kernel does not bootMarc Benoit2018-05-221-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It keeps failing (R7800) with the stack trace below BUG: scheduling while atomic: kworker/0:1/26/0x00000002 (unwind_backtrace) from [<c02121d0>] (show_stack+0x10/0x14) (show_stack) from [<c03932e4>] (dump_stack+0x7c/0x9c) (dump_stack) from [<c0239b90>] (__schedule_bug+0x5c/0x80) (__schedule_bug) from [<c05b7260>] (__schedule+0x50/0x3f4) (__schedule) from [<c05b76a8>] (schedule+0xa4/0xd4) (schedule) from [<c05ba430>] (schedule_hrtimeout_range_clock+0xc8/0x100) (schedule_hrtimeout_range_clock) from [<c05ba480>] (schedule_hrtimeout_range+0x18/0x20) (schedule_hrtimeout_range) from [<c05b9f78>] (usleep_range+0x48/0x50) (usleep_range) from [<c03f333c>] (__clk_hfpll_enable+0x44/0xd0) (__clk_hfpll_enable) from [<c03f3474>] (clk_hfpll_set_rate+0xac/0xc4) (clk_hfpll_set_rate) from [<c03ec390>] (clk_change_rate+0xf4/0x1fc) (clk_change_rate) from [<c03ec510>] (clk_core_set_rate_nolock+0x78/0x94) (clk_core_set_rate_nolock) from [<c03ec54c>] (clk_set_rate+0x20/0x30) (clk_set_rate) from [<c0424168>] (dev_pm_opp_set_rate+0x190/0x26c) (dev_pm_opp_set_rate) from [<c04a8548>] (set_target+0x40/0x108) (set_target) from [<c04a4.140>] (__cpufreq_driver_target+0x3f4/0x488) (__cpufreq_driver_target) from [<c04a7494>] (od_dbs_timer+0xcc/0x154) (od_dbs_timer) from [<c04a7998>] (dbs_work_handler+0x2c/0x54) (dbs_work_handler) from [<c02309e8>] (process_one_work+0x1c0/0x2f0) (process_one_work) from [<c02319a8>] (worker_thread+0x2a4/0x404) (worker_thread) from [<c0235944>] (kthread+0xd8/0xe8) (kthread) from [<c020eef0>] (ret_from_fork+0x14/0x24) Signed-off-by: Marc Benoit <marcb62185@gmail.com> [slh: rebase for kernel v4.14 as well] Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: add kernel 4.14 supportRam Chandra Jangir2018-05-2253-0/+19010
- Rebased the patches for 4.14 - Dropped spi-qup and 0027, 0028, 0029 clk patches since it's already included in upstream. Tested on IPQ AP148 Board: 1) NOR boot and NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org> Tested-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>