aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/files-4.9/arch
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add ipq806x specific tsens driverPavel Kubelun2017-03-271-59/+332
| | | | | | | | | | | | | | | | | Current upstream driver doesnt fully support ipq806x devices ipq806x has 11 sensors, the upstream one doesn't allow to check sensors 0-4, only 5-10. A specific driver for ipq806x has been found in Qualcomm SDK repo. https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c089e464cd7ce652419a0dc44d7959ce4d24b8a5 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c23d94b702c4182862e7f5051a2b7d00bb922a29 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=742f3684b62a6b9f082cb49404b1a92dc0b16bf5 https://source.codeaurora.org/quic/qsdk/oss/kernel/linux-msm/commit/?h=release/endive_preview_cc&id=c0a9b2e2a382c152fa128f5b864c800dd6dfb311 Merging it into LEDE with this commit. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-221-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add ipq4019 supportChristian Lamparter2017-03-224-0/+1914
| | | | | Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: remove scm firmware clocksPavel Kubelun2017-03-201-4/+1
| | | | | | | | | | | | | | At the moment as a workaround definition for scm firmware in DT is used as if it is apq8064 board. This leads to incomplete scm firmware initialization and as a result cpuidle driver fails to configure. By design unlike other qcom boards ipq do not use clocks to connect to scm. Considering this we're removing from DT and scm driver clocks for ipq boards. As a result cpuidle does not produce errors about failed configuration anymore. Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: fix ethernet DMA parameters with linux 4.9Felix Fietkau2017-03-131-0/+22
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: fix pcie with linux 4.9Felix Fietkau2017-03-131-3/+3
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: re-enable the RAM clock for gcc on 4.9Felix Fietkau2017-03-131-2/+2
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: fix NAND support for linux 4.9Felix Fietkau2017-03-137-343/+397
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: clean up dts patching in 4.9Felix Fietkau2017-03-132-0/+1271
| | | | | | | | | Do not patch upstream files, overwrite them entirely. The upstream files are buggy for a number of devices and this significantly simplifies the patch structure Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: clean up dts patchFelix Fietkau2017-03-0811-0/+3864
Move dts files to files/, remove useless patch chunks Signed-off-by: Felix Fietkau <nbd@nbd.name>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-16 05:17:06 +0000