aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/base-files
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add support for NEC Platforms Aterm WG2600HP3Yanase Yuki2020-12-253-2/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Platforms Aterm WG2600HP3 is a dual-band router based on Qualcomm IPQ8062. Specification ------------- - SoC: Qualcomm IPQ8062 - RAM: 512MiB - Flash memory: SPI-NOR 32MiB (Cypress S25FL256S) - Wi-Fi: Qualcomm QCA9984 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm QCA9984 (5GHz, 36ch - 64ch, 100ch - 140ch) - Ethernet: 4x 100/1000 Mbps (1x WAN, 4x LAN) - LED: 6x green LED, 6x red LED - Input: 2x tactile switch, 1x SP3T slide switch - Serial console: 115200bps, through-hole J3 - [ ] [GND] [ ] [TX] [RX] ----> DC jack - Power: DC 12V 1.5A This device does not support VHT160 and VHT80+80. Custom BDFs are required to limit VHT capabilities. Flash instructions ------------------ 1. Setup TFTP server (IP address: 192.168.1.2) 2. Put initramfs image into TFTP server directory 3. Connect WG2600HP3 lan port and computer that runs TFTP server 4. Connect to the serial console 5. Interrupt booting by Esc key (password: chiron) 6. Execute the following commands # setenv bootcmd "nboot 0x44000000 1 0x860000" # saveenv # setenv ipaddr 192.168.1.1 # setenv serverip 192.168.1.2 # tftpboot 0x44000000 openwrt-ipq806x-generic-nec_wg2600hp3-initramfs-uImage 7. After booting OpenWrt initramfs image, backup SPI-NOR flash memory 8. Erase firmware partition # mtd erase firmware 9. Run sysupgrade Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq806x: remove unneeded empty linesAdrian Schmutzler2020-12-222-2/+0
| | | | | | This removes two unneeded empty lines in base-files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: add support for ASRock G10Christian Lamparter2020-12-227-4/+108
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ASRock G10 is a 2.4/5 GHz band 11ac "Gaming" router, based on Qualcomm IPQ8064. Specifications: SoC: Qualcomm IPQ8064 CPU: Dual-Core A15 @ (384 - 1,400 MHz, 2C2T) DRAM: 512 MiB (~467 MiB available) NAND: 128 MB (Micron MT29F1G08ABBEAH4) WLAN0: 4T4R 5 GHz Wlan (QCA9980) WLAN1: 4T4R 2.4 GHz Wlan (QCA9980) ETH: 5x 10/100/1000 Mbps Ethernet (QCA8337) INPUT: Reset Button, WPS 2.4G and WPS 5G Button LEDS: 1 multicolor status LED USB: 2x USB 3.0 Type-A POWER: 12VDC/3A AC Adapter + dedicated Power Switch UART: Setting is 115200-8-N-1. 1x4 .1" unpopulated header on the PCB (J6 - very tiny silkscreen next to TX). Pinout: 1. 3v3 (Square - best skipped!), 2. RX, 3. GND, 4. TX WARNING: The serial port needs a TTL/RS-232 3.3v level converter! (Depending on the serial adapter RX and TX might need to be swapped). Note about the IR-Remote: There's a 8-Bit MCU (SONIX SN8F25E21SG) which is controlling the IR-Remote and is fed by the IR-Photodiode. The SoC can talk to the device via I2C. The vendor's GPL archive comes with the source of the interface driver for this as a (character driver), the main control software is however a blob. Installation Instructions: 1. Download factory image to disk 2. Apply factory image via stock web-gui Back to stock: 1. Login to router via ssh 2. run "asrock_g10_back_to_factory" script from /sbin Notes: - If something goes wrong durring sysupgrade, router will go back to factory image. - Asrock G10 uses partition layout from smem. So partition layout can be normal or alternate. - 900-arm-add-cmdline-override.patch was copied from 102-powerpc-add-cmdline-override.patch from powerpc target. Knowledge about BOOTCONFIG partition was based on user "jmomo" post from old OpenWrt forum (Post #50): https://forum.archive.openwrt.org/viewtopic.php?id=65956&p=2 Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [bump to 5.4, add factory image, fix sysupgrade, convert partition layout to smem, remove ipq-wifi-asrock-g10 and use ART, minor fixes] Co-Authored-by: Pawel Dembicki <paweldembicki@gmail.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> Tested-by: Lukasz Ostapiuk <palibrzuch@gmail.com>
* ipq806x: remove model name from LED labelsAdrian Schmutzler2020-10-072-24/+30
| | | | | | | | | | Like in the previous patches for ath79 and ramips, this will remove the "devicename" from LED labels in ipq806x. The devicename is removed in DTS files and 01_leds, and a migration script is added. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: fix support of Edgecore ECW5410 supportAdrian Schmutzler2020-09-191-2/+2
| | | | | | | | | | | | | | | | This fixes several stylistic and functional errors of the recently added Edgecore ECW5410: - fix call in 11-ath10k-caldata - use hex notation in 11-ath10k-caldata - remove redundant definitions from DTS that are already in DTSI - use proper sorting in image/Makefile - use DEVICE_VENDOR/DEVICE_MODEL instead of DEVICE_TITLE - use SOC instead of DEVICE_DTS Fixes: 59f0a0fd839e ("ipq806x: add Edgecore ECW5410 support") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: sort entries in lib/upgrade/platform.shAdrian Schmutzler2020-09-171-3/+3
| | | | | | Apply alphabetic sorting like in the other files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: remove empty default casesAdrian Schmutzler2020-09-171-2/+0
| | | | | | There is no apparent reason to have an empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: sort entries in 02_networkAdrian Schmutzler2020-09-171-5/+5
| | | | | | Apply alphabetic sorting like in the other files. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: add Edgecore ECW5410 supportRobert Marko2020-09-175-0/+33
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5410 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ8068 ARMv7 2x Cortex A-15 - RAM: 256MB(225 usable) DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB S34MS01G2 Parallel NAND - Ethernet: 2 x 1G via 2x AR8033 PHY-s connected directly to GMAC2 and GMAC3 via SGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: 2x QCA9994 AC Wawe 2 (1x 2GHz bgn, 1x 5GHz acn) - CC2540 BLE - UART console on RJ45 next to ethernet ports exposed. Its Cisco pin compatible, 115200 8n1 baud. Installation instructions: Through stock firmware or initramfs. 1.Connect to console 2. Login with root account, if password is unknown then interrupt the boot with f and reset it in failsafe. 3. Transfer factory image 4. Flash the image with ubiformat /dev/mtd1 -y -f <your factory image path> This will replace the rootfs2 with OpenWrt, if you are currently running from rootfs2 then simply change /dev/mtd1 to /dev/mtd0 Note Initramfs: 1. Connect to console 2. Transfer the image from TFTP server with tftpboot, or by using DHCP advertised image with dhcp command. 3. bootm 4. Run ubiformat /dev/mtd1 You need to interrupt the bootloader after rebooting and run: run altbootcmd This will switch your active rootfs partition to one you wrote to and boot from it. So if rootfs1 is active, then it will change it to rootfs2. This will format the rootfs2 partition, if your active partition is 2 then simply change /dev/mtd1 with /dev/mtd0 If you dont format the partition you will be writing too, then sysupgrade will find existing UBI rootfs and kernel volumes and update those. This will result in wrong ordering and OpenWrt will panic on boot. 5. Transfer sysupgrade image 6. Flash with sysupgrade -n. Note that sysupgrade will write the image to rootfs partition that is not currently in use. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq806x: enable Linksys EA8500 eth1 interfacePawel Dembicki2020-07-111-1/+1
| | | | | | | | | | | | | At this moment Linksys EA8500 uses only eth0. This patch change switch registers, which allow to use eth1 as lan and eth0 as wan. The method work with similar Linksys EA7500V1 and it work with EA8500. Suggested-by: Sungbo Eo <mans0n@gorani.run> Tested-by: Brian Onn <brian.a.onn@gmail.com> Tested-by: Adrian Panella <ianchi74@outlook.com> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq806x: add support for Linksys EA7500 V1Pawel Dembicki2020-07-084-0/+11
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Linksys EA7500 V1 router. Specification: - CPU: Qualcomm IPQ8064 - RAM: 256MB - Flash: NAND 128MB - WiFi: QCA9982 an+ac + QCA9983 bgn - Ethernet: 5 GBE Ports (WAN+ 4xLAN) (QCA8337) - USB: 1x USB 3.0 1x USB2.0 - Serial console: RJ-45 115200 8n1 (1V8 Voltage level) - 2 Buttons - 1 LED Known issues: - Some devices won't flash via web gui Installation: - Newer stock images doesn't allow to install custom firmware. - Please downgrade software to 1.1.2 version. Official firmware: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.gpg.img - Do it two times to downgrade all stored images. - Apply factory image via web-gui. Serial + TFTP method: - downgrade to 1.1.2 two times - connect ehternet and serial cable - set ip address of tftp server to 192.168.1.254 - put openwrt factory image to tftp folder and rename it to macan.bin - stop device while booting in u-boot - run command: "run flashimg" - run command: "setenv boot_part 1" - run command "saveenv" - reset Back to stock: - Please use old non-gpg image like this 1.1.2: https://downloads.linksys.com/downloads/firmware/FW_EA7500_1.1.2.172843_prod.img - ssh to router and copy image to tmp - use sysupgrade -n -F Tested by github users: @jack338c and @grzesiczek1 Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> [removed i2c4_pins, mdio0_pins, nand_pins, rgmii2_pins from DTSI] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-161-1/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: EA8500 fix boot partition detectionSamantha Collard2020-05-311-2/+0
| | | | | | | Remove extraneous code that disabled boot partition detection. Fixes: b3770eaca39f ("mtd: base-files: Unify dual-firmware devices (Linksys)") Signed-off-by: Samantha Collard <sammyrc34@gmail.com>
* ipq806x: read both WG2600HP MAC addresses from flashYanase Yuki2020-03-161-1/+1
| | | | | | | | | WG2600HP has its WLAN MAC addresses at PRODUCTDATA 0xc and 0x12, so use them both directly. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> [commit title/message clarification] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: remove useless case within default case for upgradeAdrian Schmutzler2020-03-161-1/+0
| | | | | | | The default case will catch anything left, there is no need to explicitly add any device to it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq806x: use switch trigger for WAN LED on NETGEAR boardsDavid Bauer2019-11-041-1/+1
| | | | | | | | | With this commit, the WAN LED is triggered by the switch port state instead of the eth0 netdev. Otherwise, the LED is always illuminated, regardless of the WAN port link state. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: use a single ath10k MAC patching function with checksumAdrian Schmutzler2019-10-151-14/+14
| | | | | | | | | | | | | | | | While all ath10k eeproms have a checksum field, so far two functions for patching ath10k MAC address have been present (and been used). This merges code to provide a single function ath10k_patch_mac in caldata.sh, having its name in accordance with ath9k functions. By doing so, correct MAC patching for current and future ath10k devices should be ensured. This patch adds checksum adjustments for several targets on ath79 and lantiq. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move MAC address patch functions to common libraryAdrian Schmutzler2019-10-141-25/+0
| | | | | | | | | This unifies MAC address patch functions and moves them to a common script. While those were implemented differently for different targets, they all seem to do the same. The number of different variants is significantly reduced by this patch. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move calibration data extraction function to libraryAdrian Schmutzler2019-10-131-46/+16
| | | | | | | | | | | | | | | | | This moves the almost identical calibration data extraction functions present multiple times in several targets to a single library file /lib/functions/caldata.sh. Functions are renamed with more generic names to merge different variants that only differ in their names. Most of the targets used find_mtd_chardev, while some used find_mtd_part inside the extraction code. To merge them, the more abundant version with find_mtd_chardev is used in the common code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> [rebase on latest master; add mpc85xx] Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: move xor() from caldata extraction to functions.shAdrian Schmutzler2019-10-131-16/+1
| | | | | | | | The xor() function is defined in each of the caldata extraction scripts for several targets. Move it to functions.sh to reduce duplicate code. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use new procd sysupgrade $UPGRADE_BACKUP variableRafał Miłecki2019-09-051-1/+1
| | | | | | | | | | It's a variable set by procd that should replace hardcoded /tmp/sysupgrade.tgz. This change requires the most recent procd with the commit 0f3c136 ("sysupgrade: set UPGRADE_BACKUP env variable"). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: when copying a backup file always specify dest nameRafał Miłecki2019-09-051-1/+1
| | | | | | | $CONF_TAR shouldn't be assumed to always point to the sysupgrade.tgz. This change makes code more generic and allows refactoring $CONF_TAR. Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: don't hardcode "sysupgrade.tgz" file nameRafał Miłecki2019-09-051-1/+1
| | | | | | | | 1) Add BACKUP_FILE and use it when copying an archive to be restored after sysupgrade (on the next preinit). 2) Use CONF_TAR for copying backup prepared by the /sbin/sysupgrade Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq806x: Replace backticks by $(...)Adrian Schmutzler2019-08-312-4/+4
| | | | | | This replaces deprecated backticks by more versatile $(...) syntax. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sync bootcount scripts across targetsChuanhong Guo2019-08-171-3/+1
| | | | | | | | | | | | | | | This commit made the following changes to sync all bootcount scripts: 1. use boot() instead of start() This script only needs to be executed once when boot is complete. use boot() to make this explicit. 2. drop sourcing of /lib/functions.sh This is aready done in /etc/rc.common. 3. ramips: replace board name checking with a case Signed-off-by: Chuanhong Guo <gch981213@gmail.com>
* treewide: convert WiFi caldata size and offset to hexadecimalAdrian Schmutzler2019-08-141-18/+18
| | | | | | | | | | | | | | This changes size and offset set for WiFi caldata extraction and MAC address adjustment to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-cal-data in DTS files. Since dd cannot deal with hexadecimal notation, one has to convert back to decimal by simple $(($hexnum)). Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: convert MAC address location offsets to hexadecimalAdrian Schmutzler2019-08-141-10/+10
| | | | | | | | | | | | | This changes the offsets for the MAC address location in mtd_get_mac_binary* and mtd_get_mac_text to hexadecimal notation. This will be much clearer for the reader when numbers are big, and will also match the style used for mtd-mac-address in DTS files. (e.g. 0x1006 and 0x5006 are much more useful than 4102 and 20486) Acked-by: Alexander Couzens <lynxis@fe80.eu> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: sysupgrade: get rid of platform_nand_pre_upgrade()Rafał Miłecki2019-07-222-10/+6
| | | | | | | | | | | 1) nand_do_upgrade() is always called by a target code 2) nand_do_upgrade() starts with calling platform_nand_pre_upgrade() It means there is no need for the platform_nand_pre_upgrade() callback at all. All code that was present there could bo moved & simplly called by a target right before the nand_do_upgrade(). Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* treewide: sysupgrade: don't use $ARGV in platform_do_upgrade()Rafał Miłecki2019-07-171-6/+6
| | | | | | | stage2 passes image path to platform_do_upgrade() as an argument so it can be simply accessed using $1 Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-183-38/+51
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* ipq806x: fix LED configuration for NEC Aterm WG2600HPINAGAKI Hiroshi2019-02-281-1/+1
| | | | | | | NEC WG2600HP uses port1 on QCA8337 as a WAN port, so "0x2" should be used as a portmask instead of "0x1e" for "WAN" LED configuration. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for Buffalo WXR-2533DHPINAGAKI Hiroshi2019-01-015-0/+63
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WXR-2533DHP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. The U-Boot on WXR-2533DHP employs a complicated dual firmware protection scheme against corruptions of the kernel and rootfs images. See the notes in buffalo.sh for details. specifications: - Qualcomm IPQ8064 (384 - 1,400 MHz, 2C2T) - 512 MB of RAM (DDR3) - 256 MB of Flash (NAND) - 4T4R 2.4/5 GHz Wlan (QCA9980) - 5x 10/100/1000 Mbps Ethernet - 10x LEDs, 8x keys (6x buttons, 2x slide-switches) - 2x USB 3.0 Type-A - 12VDC/4A AC Adapter - UART through-hole on PCB - J3: Vcc, GND, TX, RX from USB port side - 115200n8 Boot instructions for the initramfs image: 1. Prepare the TFTP server with the initramfs image renamed to "wxr2300dhp-initramfs.uImage" and IP address "192.168.11.10". 2. Press the "AOSS" button while powering on the WXR-2533DHP. 3. Wait until the "Wireless" LED flashes before releasing the AOSS button. The WXR-2533DHP will grab the image from TFTP server and will boot it. Flashing instructions: To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. Then wait ~120 seconds to let it finish the flashing process. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded message]
* ipq806x: add ath10k calibration data MAC addresses patchingChristian Lamparter2018-12-152-35/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Ben Greear reported in his patch: |Subject: netgear r7800: Fix mac address of radios. | |Reloading the driver causes the phyX to change, and that |caused the MAC address to change. This is because all ODM/OEMs except QCA bothered to write the correct MAC address for the ath10k wifi into the calibration data. This patch copies over the MAC patching helper functions from ipq40xx's target/linux/ipq40xx/base-files/etc/hotplug.d/firmware/11-ath10k-caldata file and converts all the devices to patch the correct MACs into the extracted calibration data before it gets sent to the driver, which sets up the device with the correct MAC address. It also removes the entries in the 10_fix_wifi_mac file as they have served their purpose for good. Please note the C2600: There is conflicting information on what the offset for the second wifi is supposed to be. This patch uses what was specified in 10_fix_wifi_mac. According to Ben Greear this method is save to use with the stock firmware too. As he explained that the stock firmware messes up rx-bssid mask calculation when the MAC is changed after the first vif is created. Reported-by: Ben Greear <greearb@candelatech.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* apm821xx, ath79, ipq40xx, ipq806x, lantiq, ramips: base-files: Use generic ↵Petr Štetiar2018-12-061-46/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | diag.sh I wanted to add status LEDs support to my imx6 based board and have found out, that I could use diag.sh script found in ramips platform, which seems to be also shared in a few other platforms: 4801276bc2078c5bcf03003c831e3b0a target/linux/ramips/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ipq40xx/base-files/etc/diag.sh 4801276bc2078c5bcf03003c831e3b0a target/linux/ath79/base-files/etc/diag.sh And @chunkeey suggested to me, that I can also add lantiq, ipq806x and apm821xx to the list of platforms which could share this generic diag.sh. I've extended the base diag.sh in a way, that if it detects any of the DTS LED aliases, then it would use the generic DTS set_led_state code. The code in platform's diag.sh has moved to base-files package in this commit: base-files: diag.sh: Make it more generic towards DTS so it could be reused Signed-off-by: Petr Štetiar <ynezz@true.cz> Tested-by: Christian Lamparter <chunkeey@gmail.com> (apm821xx and ipq40xx)
* ipq806x: Add support for IPQ8064 AP161 boardRam Chandra Jangir2018-11-262-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specification: - SoC: Qualcomm Atheros IPQ8064 ARM-v7 Dual Core SMP CPU - RAM: 512MB DDR3 System Memory - NOR Flash: 32MB SPI NOR - NAND Flash: 256MB NAND - Ethernet: 5 x 1G via QCA8337N - USB: 2 x USB 3.0 SuperSpeed - PCIe: 3x Mini PCIe 2.0 Slots Three PCIE2.0 connectors can connect two or three radio cards such as the CUS260 for 2.4 GHz WLAN and the CUS239 for 802.11ac WLAN How to flash via u-boot console: tftpboot 0x44000000 openwrt-ipq806x-qcom_ipq8064-ap161-squashfs-nand-factory.bin nand erase 0x1340000 0x4000000 nand write 0x44000000 0x1340000 $filesize setenv bootargs ‘console=ttyMSM0,115200 ubi.mtd=ubi root=/dev/ubiblock0_1’ saveenv bootm Further upgrades via sysupgrade. Tested on IPQ8064 AP161 Board: 1) NAND boot 2) Tested USB and PCIe interfaces 3) WDOG test 4) cpu frequency scaling 5) ethernet, 2G and 5G WiFi 6) ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* hotplug: Allow configuring radio name.Ben Greear2018-11-261-0/+21
| | | | | | | | | | | | | This way the radio (phy) name can be the same through module reloads. To set the desired name: uci set wireless.@wifi-device[0].phyname=wiphy0 I guess this only works on ipq6086 boards as I could not find a more generic place to put this. Maybe someone can improve it. Signed-off-by: Ben Greear <greearb@candelatech.com>
* treewide: fix upgrade led handlingMathias Kresin2018-08-161-2/+4
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: consolidate upgrade state setMathias Kresin2018-08-161-6/+0
| | | | | | | | | | Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: fix numbering for Netgear R7800 LAN portsAleksandr V. Piskunov2018-07-041-5/+5
| | | | | | | | | | Netgear R7800 switch LAN ports are numbered backwards in LuCI, i.e. numbering is not corresponding to the actual physical port labels, patch fixes that. Signed-off-by: Aleksandr V. Piskunov <aleksandr.v.piskunov@gmail.com> [merged with existing board using the same config] Signed-off-by: Hannu Nyman <hannu.nyman@iki.fi>
* ipq806x: switch the NBG6817 wlan LEDs from amber to whiteStefan Lippers-Hollmann2018-06-281-2/+0
| | | | | | | | | | | | | | | | | The original device support patch configured the amber wlan LEDs (which are meant as error indicator by the OEM) controlled by the SOC's GPIO as wlan traffic indicators, as the correct white wlan LEDs are connected to GPIOs controlled by the QCA9984/ ath10k wlan cards were not accessible. The recent addition of GPIO/ LED support to ath10k now makes it possible to use the correct white LEDs instead - and "mac80211: ath10k: use tpt LED trigger by default" also enables them by default. While both LEDs are independent of each other (two separate LEDs sharing one light tunnel), triggering both on wlan traffic is not the intended behaviour (bright yellow light). Tested on the ZyXEL NBG6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: add support for NEC Aterm WG2600HPINAGAKI Hiroshi2018-06-195-0/+15
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | NEC Aterm WG2600HP is a 2.4/5 GHz band 11ac router, based on Qualcomm IPQ8064. Specification: - IPQ8064 (384 - 1,400 MHz) - 512 MB of RAM - 32 MB of Flash (SPI) - 4T4R 2.4/5 GHz - 5x 10/100/1000 Mbps Ethernet - 12x LEDs, 4x keys - 1x USB 3.0 Type-A - UART header on PCB - RX, TX, NC, GND, Vcc from power connector side - baudrate: 115200 bps Flash instruction using initramfs image: 1. Connect serial cable to UART header 2. Connect power cable and turn on the router 3. When the "Press the [f] key and hit [enter] to enter failsafe mode" message is displayed on the console, press the "f" key and Enter key sequentially to enter the failsafe mode 4. create fw_env.config file with following contents on failsafe mode: /dev/mtd9 0x0 0x10000 0x10000 5. Execute following commands to add and change the environment variables of U-Boot fw_setenv ipaddr "192.168.0.1" fw_setenv serverip "192.168.0.2" fw_setenv autostart "yes" fw_setenv bootcmd "tftpboot 0x44000000 wg2600hp-initramfs.bin; bootipq" 6. Set the IP address of the computer to 192.168.0.2, connect to the LAN port of WG2600HP, and start the TFTP server on the computer 7. Rename OpenWrt initramfs image for WG2600HP to "wg2600hp-initramfs.bin" and place it in the TFTP directory 8. Remove power cable from WG2600HP, reconnect it and restart WG2600HP 9. WG2600HP downloads initramfs image from TFTP server on the computer, loads it and boot with initramfs image 10. On the initramfs image, execute "mtd erase firmware" to erase stock firmware and execute sysupgrade with the sysupgrade image 11. Wait ~180 seconds to complete flashing Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq806x: add support for Compex WPQ864Christian Mehlis2018-03-153-10/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware highlights: - SoC: Qualcomm Atheros IPQ8064/5 ARM Dual Core CPU - RAM: (512MB or 1GB) DDR3 System Memory - Storage: 32MB NOR (Cypress S25FL256S1) 256MB NAND (Micron MT29F2G08ABBEAH4) - Ethernet: 5 x 1G via QCA8337N - USB: 1 x USB 2.0/3.0 + 1 x USB 2.0 on mini PCIe3 socket - PCIe: 3x mini PCIe (third mini PCIE3 is PCIe/USB shared) - SIM Card Slot: 2 x Slot - Buttons: Reset Button - LEDs: 18x, 8x GPIO controllable - Buzzer The correct amount of RAM will be passed by the bootloader. In contrast to the documentation provided by Compex, the third PCIe doesn't use GPIO16 for PERST. Instead, GPIO3 is shared and used as PERST for PCIe0 and PCIe2. So far, no one was able to get USB 3.0 working with the 1GB RAM version, while it works fine for my 512MB version. Since USB 3.0 doesn't work with the Compex firmware for the 1G variant either, it could be a hardware issue with these boards. OpenWrt will be installed to the NAND flash. Make sure to have a full working image on the NOR flash. It will be the backup in case anything goes wrong. It has been observed that an image loaded via tftpboot might have bitflips. Hence the extra step to create a crc32 checksum to allow to compare the checksum with the one from the source file prior to flashing. In all cases it is necessary to set the following u-boot parameter to an empty (whitespace) value, to ensure that the chosen bootargs of the dts isn't overwritten or set to bogus - not working - values: (IPQ) # set bootargs " " (IPQ) # set fsbootargs " " (IPQ) # saveenv The sysupgrade image can be installed directly on flash using u-boot (put jumper in JP13 (leave JP9 open) to boot from nand): (IPQ) # set serverip 192.168.1.20 (IPQ) # set ipaddr 192.168.1.1 (IPQ) # tftpboot 0x42000000 openwrt-ipq806x-compex_wpq864-squashfs-nand-factory.bin (IPQ) # crc32 0x42000000 $filesize (IPQ) # nand erase 0x1340000 0x4000000 (IPQ) # nand write 0x42000000 0x1340000 $filesize The initramfs image can be started using: (IPQ) # set fdt_high 0x48000000 (IPQ) # tftpboot 0x44000000 openwrt-ipq806x-compex_wpq864-initramfs-fit-uImage.itb (IPQ) # bootm 0x44000000 Signed-off-by: Christian Mehlis <christian@m3hlis.de> Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: drop ipq40xx supportJohn Crispin2018-03-145-161/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add support for GL.iNet GL-B1300Dongming Han2018-02-143-0/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for GL.iNet GL-B1300 Specification: - SOC: IPQ4028 / QCA Dakota - RAM: 256 MiB - FLASH: 32 MiB - ETH: Qualcomm Atheros QCA8075 Gigabit Switch (2 x LAN, 1 x WAN) - USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) - WLAN1: Qualcomm Atheros QCA4028 2.4GHz 802.11bgn 2:2x2 - WLAN2: Qualcomm Atheros QCA4028 5GHz 802.11a/n/ac 2:2x2 - INPUT: one reset and one WPS button - LEDS: 3 leds: Power, WIFI(only for 2.4G currently), and one reserved - UART: 1 x UART on PCB (3.3V, TX, RX, GND) - 115200 8N1 Installation: Method 1: - use serial port to stop uboot - uboot command: run lf Method 2: - push down reset button and power on - wait until three leds constantly on then release - upgrade by uboot web at http://192.168.1.1 Note: - the sysupgrade image need to be renamed to lede-gl-b1300.bin in both method. - the sysupgrade image can be automatically downloaded if tftp server at 192.168.1.2 have that file. - the wifi led will be flashing when writing image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq806x: switch to full dual-boot for the nbg6817 sysupgrade supportStefan Lippers-Hollmann2018-02-131-3/+23
| | | | | | | | | | | | | | Instead of writing to the currently booted partition set, this implements full dual-boot support for sysupgrade by always writing to the other, currently inactive, partition set and toggling the dualflag after a successful flash. The currently active/ booted partition set is determined by parsing /proc/cmdline for its rootfs parameter (supplied by the DTS), instead of reading from the 0:DUAL_FLAG mtd, in order to prevent (potentially) bricking both partition sets. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: request the first free loop device dynamically for the nbg6817 ↵Stefan Lippers-Hollmann2018-02-131-4/+5
| | | | | | | | | | | | sysupgrade Instead of hardcoding /dev/loop0, it's safer to query for the first free loop device and assign that dynamically. While /dev/loop0 is a reasonable assumption immediately following "losetup --detach-all", detaching the mounted overlay is no longer strictly necessary once dual-boot support has been added for the nbg6817. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: use absolute the device path in $kernel for the nbg6817 sysupgradeStefan Lippers-Hollmann2018-02-131-4/+4
| | | | | | | Harmonize the variable usage for $kernel and $rootfs to always contain the full device path, instead of just its basename. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq806x: mark AVM FB4040 switchport as untaggedDavid Bauer2018-02-111-1/+1
| | | | | | | | This commit marks the CPUs switchport explicit as untagged. Otherwise, an eth0.1 interface is created and the devices LAN-ports are not working. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq806x: fix ZyXEL NBG6817 sysupgradeMathias Kresin2018-01-181-7/+10
| | | | | | | | | | | Use the first found directory in the tar archive instead of relying on a directory named according to the userspace boardname. It allows to change the boardname without adding another compatibility layer to the zyxel sysupgrade. Fixes: 33f09cf15178 ("ipq806x: convert to dt-based board-detection") Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-134-0/+123
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-26 15:55:01 +0000