aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: add support for OpenMesh A42Sven Eckelmann2018-01-131-0/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ401x * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=OM-A42 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=OM-A42 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet * powered only via POE - 802.3af POE on Ethernet 1 - 18-24v passive POE (mode B) on Ethernet 2 The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq806x: Sort occurrences of boardame alphabeticallyLuis Araneda2018-01-131-3/+3
| | | | | | | This restores the alphabetical sort that was present before the renaming of boardname. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* ipq806x: convert to dt-based board-detectionLuis Araneda2018-01-131-11/+11
| | | | | | | | | | | | | | | | | Use the generic board detection method: - Board name: First compatible string from the device tree - Board model: Model property from the device tree Change occurrences of board name in userspace by the compatible string, and removed target specific board detection script Replace the definition of SUPPORTED_DEVICES in Device/Default to extract the dt compatible string from each device definition. Additionally, for devices supported by lede-17.01, append the value of BOARD_NAME to SUPPORTED_DEVICES in the device definition. Signed-off-by: Luis Araneda <luaraneda@gmail.com>
* treewide: use the generic board_name functionMathias Kresin2017-07-151-8/+2
| | | | | | Use the generic function instead ot the target specific ones. Signed-off-by: Mathias Kresin <dev@kresin.me>
* base-files: automatically handle paths and symlinks for RAMFS_COPY_BINMatthias Schiffer2017-07-111-1/+1
| | | | | | | | | | | | Depending on busybox applet selection, paths of basic utiilties may differ, and may not work as symlinks to busybox. Simply using whatever binary is found in PATH and detecting symlinks automatically is more robust and easier to maintain. The list of binaries is also slightly cleaned up and duplicates are removed. Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ipq806x: upgrade: fix RAMFS_COPY_*Matthias Schiffer2017-07-111-12/+5
| | | | | | | | | RAMFS_COPY_* are moved to platform.sh toplevel. The unneeded linksys_preupgrade function is removed, and the nand_do_upgrade call is moved to platform_do_upgrade. Fixes: 30f61a34b4cf "base-files: always use staged sysupgrade" Signed-off-by: Matthias Schiffer <mschiffer@universe-factory.net>
* ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 boardRam Chandra Jangir2017-06-071-0/+1
| | | | | | | | | | | | | | This change add IPQ40xx AP-DK04.1-C1 board image support, enables ubi image for IPQ40xx AP-DK04.1-C1 board and also add sysupgrage support for AP-DK04.1-C1 and generates a sysupgrade.tar image. Testing: *Tested on IPQ40xx AP-DK04.1-C1: a. NAND boot b. ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-241-0/+5
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* ipq806x: remove device specific sysupgrade image checksFelix Fietkau2016-11-201-24/+1
| | | | | | Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: append metadata to imagesFelix Fietkau2016-11-191-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x/nbg6817: add sysupgrade supportAndré Valentin2016-10-261-0/+12
| | | | | | Add new way of flashing to mmc devices based on rootfs split with loop devices. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x: add support for indicating the boot and upgrade state using four ledsHenryk Heisig2016-10-151-0/+6
| | | | Signed-off-by: Henryk Heisig hyniu@o2.pl
* ipq806x: Build image for Netgear Nighthawk X4 R7500v2Alexis Green2016-08-221-0/+2
| | | | | | Signed-off-by: Alexis Green <alexis@cessp.it> [Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add initial support for Netgear R7800Pavel Kubelun2016-06-221-2/+4
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: base-files: add support for Linksys EA8500Adrian Panella2016-06-131-0/+7
| | | | Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x/base-files: Add support for Archer C2600Ash Benz2016-05-271-1/+19
| | | | Signed-off-by: Ash Benz <ash.benz@bk.ru>
* ipq806x: Add support for Netgear D7800John Crispin2016-01-191-0/+2
| | | | | | Signed-off-by: Tathagata Das <tathagata@alumnux.com> SVN-Revision: 48360
* ipq806x: fix sysupgrade for AP148Jonas Gorski2016-01-181-2/+2
| | | | | | | | | AP148 uses lowercase name as boardname, so we need to use this in platform.sh as well. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48304
* ipq806x: add platform_pre_upgrade for sysupgradeRafał Miłecki2015-09-151-0/+11
| | | | | | | | | | | | | | | | We're in process of cleaning nand_do_platform_check. Currently is leaves a special mark in /tmp/sysupgrade-nand-path triggering some diffent code path in nand_upgrade_stage1. This can be a bit confusing. The plan is to have the check function only check the image and nothing else. Then platform code (platform_pre_upgrade) should trigger NAND specific upgrade path. This is what this patch implements. This follows ar71xx, lantiq and partially bcm53xx. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 46945
* ipq806x: add support for Netgear Nighthawk X4 R7500Jonas Gorski2015-09-041-1/+2
| | | | | | | | | | | | | Add support for the Netgear Nighthawk X4 R7500 and build appropariate sysupgrade and factory images. Known issues: * 5 GHz wifi not working - there is no quantenna driver * One of the USB ports is not working Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46796
* ipq806x: build images and add sysupgrade support for AP148Jonas Gorski2015-09-041-0/+18
Add full ubi and sysupgrade images for AP148 and add sysupgrade support for ipq806x to allow updating the current installation. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46789
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-07 19:15:11 +0000