aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq806x/base-files/lib/upgrade/platform.sh
Commit message (Collapse)AuthorAgeFilesLines
* ipq806x: Enable ubi image for ipq40xx AP-DK04.1-C1 boardRam Chandra Jangir2017-06-071-0/+1
| | | | | | | | | | | | | | This change add IPQ40xx AP-DK04.1-C1 board image support, enables ubi image for IPQ40xx AP-DK04.1-C1 board and also add sysupgrage support for AP-DK04.1-C1 and generates a sysupgrade.tar image. Testing: *Tested on IPQ40xx AP-DK04.1-C1: a. NAND boot b. ubi sysupgrade Signed-off-by: Ram Chandra Jangir <rjangir@codeaurora.org>
* ipq806x: add ipq4019 fritz4040 supportChristian Lamparter2017-03-221-0/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for AVM FRITZ!Box 4040. hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB Nanya NT5CC128M16IP FLASH: 32 MiB MXIC MX25L25635FMI ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) 1 x 2.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: one WLAN and one WPS button LEDS: Power, WAN/Internet, WIFI, INFO (red and amber) and LAN. Serial: WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. The SoC's serial port is right next to the MXIC FLASH chip. The board has a unpopulated 1x4 0.1" header for it. Use a multimeter to figure out the pinout! This board currently needs an additional u-boot image in order to boot properly. Booting with EVA isn't possible ATM. Install Procedure: 0. It's highly recommended to connect to the serial port. The serial settings are listed above. 1. install a u-boot image for AVM Fritz!Box 4040 (see <https://github.com/chunkeey/FritzBox-4040-UBOOT/releases> and <https://github.com/chunkeey/FritzBox-4040-UBOOT/blob/master/upload-to-f4040.sh>) 2. upload the initramfs.itb image via tftp (u-boot listens to 192.168.1.1 - use binary transfer mode!) 3. connect to the FB4040 and use sysupgrade sysupgrade.bin to install the image. Works: - Switch and Ethernet (99%) - Buttons (WLAN, WPS) - FLASH (1 x 32MiB NOR Chip) - WLAN2G and WLAN5G - CPUFREQ scaling - PRNG - serial - Crypto Accelerator - sysupgrade (Read the flash instructions to avoid bricking) - full LEDE Install (Read the flash instructions to avoid bricking) - LEDs (Power, WAN, Info (red and amber), LAN) The LEDs are connected to the QCA8075 LED ports. The AR40xx driver contains a gpio-controller to handle these special "GPIOs". - USB Both 3.0 and 2.0 ports - many packages from other ARMv7 boards (This does include the RaspberryPi Model 2!) - ... Not planned: - WAN<->LAN short-cut - Qualcomm Secure Execution Environment - ... Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: John Crispin <john@phrozen.org>
* ipq806x: add support for TP-Link Archer VR2600vSebastian Quilitz2016-11-241-0/+5
| | | | | | | | | | | | | | | | | | This router is similar to the C2600. Ethernet on WAN + LAN, switch, sysupgrade, LEDs, buttons and WiFi on 2G + 5G do work. The xDSL modem and the POTS/DECT interface are not supported yet. It is not possible to flash LEDE via the TP-Link webinterface. The image need to be signed. The first 0x200 bytes of the image is the TP-Link header including the signature. The signature is not validated by the bootloader. The LEDE image is zeroed in this area. To install LEDE it is necessary to solder a four pin header to JP2. Connect a serial interface to this header and interrupt the autostart of kernel. Transfer the sysupgrade image via TFTP and write it to the serial flash at 0x320000. Signed-off-by: Sebastian Quilitz <zeraphim@x-pantion.de>
* ipq806x: remove device specific sysupgrade image checksFelix Fietkau2016-11-201-24/+1
| | | | | | Replaced by image metadata Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x: append metadata to imagesFelix Fietkau2016-11-191-0/+1
| | | | Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq806x/nbg6817: add sysupgrade supportAndré Valentin2016-10-261-0/+12
| | | | | | Add new way of flashing to mmc devices based on rootfs split with loop devices. Signed-off-by: André Valentin <avalentin@marcant.net>
* ipq806x: add support for indicating the boot and upgrade state using four ledsHenryk Heisig2016-10-151-0/+6
| | | | Signed-off-by: Henryk Heisig hyniu@o2.pl
* ipq806x: Build image for Netgear Nighthawk X4 R7500v2Alexis Green2016-08-221-0/+2
| | | | | | Signed-off-by: Alexis Green <alexis@cessp.it> [Jo-Philipp Wich: add missing DEVICE_TITLE, fix model name in commit title] Signed-off-by: Jo-Philipp Wich <jo@mein.io>
* ipq806x: add initial support for Netgear R7800Pavel Kubelun2016-06-221-2/+4
| | | | Signed-off-by: Pavel Kubelun <be.dissent@gmail.com>
* ipq806x: base-files: add support for Linksys EA8500Adrian Panella2016-06-131-0/+7
| | | | Signed-off-by: Adrian Panella <ianchi74@outlook.com>
* ipq806x/base-files: Add support for Archer C2600Ash Benz2016-05-271-1/+19
| | | | Signed-off-by: Ash Benz <ash.benz@bk.ru>
* ipq806x: Add support for Netgear D7800John Crispin2016-01-191-0/+2
| | | | | | Signed-off-by: Tathagata Das <tathagata@alumnux.com> SVN-Revision: 48360
* ipq806x: fix sysupgrade for AP148Jonas Gorski2016-01-181-2/+2
| | | | | | | | | AP148 uses lowercase name as boardname, so we need to use this in platform.sh as well. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 48304
* ipq806x: add platform_pre_upgrade for sysupgradeRafał Miłecki2015-09-151-0/+11
| | | | | | | | | | | | | | | | We're in process of cleaning nand_do_platform_check. Currently is leaves a special mark in /tmp/sysupgrade-nand-path triggering some diffent code path in nand_upgrade_stage1. This can be a bit confusing. The plan is to have the check function only check the image and nothing else. Then platform code (platform_pre_upgrade) should trigger NAND specific upgrade path. This is what this patch implements. This follows ar71xx, lantiq and partially bcm53xx. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> SVN-Revision: 46945
* ipq806x: add support for Netgear Nighthawk X4 R7500Jonas Gorski2015-09-041-1/+2
| | | | | | | | | | | | | Add support for the Netgear Nighthawk X4 R7500 and build appropariate sysupgrade and factory images. Known issues: * 5 GHz wifi not working - there is no quantenna driver * One of the USB ports is not working Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46796
* ipq806x: build images and add sysupgrade support for AP148Jonas Gorski2015-09-041-0/+18
Add full ubi and sysupgrade images for AP148 and add sysupgrade support for ipq806x to allow updating the current installation. Signed-off-by: Jonas Gorski <jogo@openwrt.org> SVN-Revision: 46789
generated by cgit v1.2.3 (git 2.25.1) at 2024-08-15 02:17:51 +0000