aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: Add support for Linksys MR8300 (Dallas)Hans Geiblinger2020-09-2512-314/+421
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Luma Home WRTQ-329ACNTomasz Maciej Nowak2020-09-256-2/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Luma Home WRTQ-329ACN, also known as Luma WiFi System, is a dual-band wireless access point. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 2 MB SPI NOR 128 MB SPI NAND WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 2x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 Bluetooth: 1x 4.0 CSR8510 A10, connected to USB bus LEDS: 16x multicolor LEDs ring, controlled by MSP430G2403 MCU Buttons: 1x GPIO controlled EEPROM: 16 Kbit, compatible with AT24C16 UART: row of 4 holes marked on PCB as J19, starting count from the side of J19 marking on PCB 1. GND, 2. RX, 3. TX, 4. 3.3V baud: 115200, parity: none, flow control: none The device supports OTA or USB flash drive updates, unfotunately they are signed. Until the signing key is known, the UART access is mandatory for installation. The difficult part is disassembling the casing, there are a lot of latches holding it together. Teardown Prepare three thin, but sturdy, prying tools. Place the device with back of it facing upwards. Start with the wall having a small notch. Insert first tool, until You'll feel resistance and keep it there. Repeat the procedure for neighbouring walls. With applying a pressure, one edge of the back cover should pop up. Now carefully slide one of the tools to free the rest of the latches. There's no need to solder pins to the UART holes, You can use hook clips, but wiring them outside the casing, will ease debuging and recovery if problems occur. Installation 1. Prepare TFTP server with OpenWrt initramfs image. 2. Connect to UART port (don't connect the voltage pin). 3. Connect to LAN port. 4. Power on the device, carefully observe the console output and when asked quickly enter the failsafe mode. 5. Invoke 'mount_root'. 6. After the overlayfs is mounted run: fw_setenv bootdelay 3 This will allow to access U-Boot shell. 7. Reboot the device and when prompted to stop autoboot, hit any key. 8. Adjust "ipaddr" and "serverip" addresses in U-Boot environment, use 'setenv' to do that, then run following commands: tftpboot 0x84000000 <openwrt_initramfs_image_name> bootm 0x84000000 and wait till OpenWrt boots. 9. In OpenWrt command line run following commands: fw_setenv openwrt "setenv mtdids nand1=spi_nand; setenv mtdparts mtdparts=spi_nand:-(ubi); ubi part ubi; ubi read 0x84000000 kernel; bootm 0x84000000" fw_setenv bootcmd "run openwrt" 10. Transfer OpenWrt sysupgrade image to /tmp directory and flash it with: ubirmvol /dev/ubi0 -N ubi_rootfs sysupgrade -v -n /tmp/<openwrt_sysupgrade_image_name> 11. After flashing, the access point will reboot to OpenWrt, then it's ready for configuration. Reverting to OEM firmware 1. Execute installation guide steps: 1, 2, 3, 7, 8. 2. In OpenWrt command line run following commands: ubirmvol /dev/ubi0 -N rootfs_data ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N kernel ubirename /dev/ubi0 kernel1 kernel ubi_rootfs1 ubi_rootfs ubimkvol /dev/ubi0 -S 34 -N kernel1 ubimkvol /dev/ubi0 -S 320 -N ubi_rootfs1 ubimkvol /dev/ubi0 -S 264 -N rootfs_data fw_setenv bootcmd bootipq 3. Reboot. Known issues The LEDs ring doesn't have any dedicated driver or application to control it, the only available option atm is to manipulate it with 'i2cset' command. The default action after applying power to device is spinning blue light. This light will stay active at all time. To disable it install 'i2c-tools' with opkg and run: i2cset -y 2 0x48 3 1 0 0 i The light will stay off until next cold boot. Additional information After completing 5. step from installation guide, one can disable asking for root password on OEM firmware by running: sed -e 's/root:x:/root::/' -i /etc/passwd This is useful for investigating the OEM firmware. One can look at the communication between the stock firmware and the vendor's cloud servers or as a way of making a backup of both flash chips. The root password seems to be constant across all sold devices. This is output of 'led_ctl' from OEM firmware to illustrate possibilities of LEDs ring: Usage: led_ctl [status | upgrade | force_upgrade | version] led_ctl solid COLOR <brightness> led_ctl single COLOR INDEX <brightness 0 - 15> led_ctl spinning COLOR <period 1 - 16 (lower = faster)> led_ctl fill COLOR <period 1 - 16 (lower = faster)> ( default is 5 ) led_ctl flashing COLOR <on dur 1 - 128> <off dur 1 - 128> (default is 34) ( default is 34 ) led_ctl pulsing COLOR COLOR: red, green, blue, yellow, purple, cyan, white Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [squash "ipq-wifi: add BDFs for Luma Home WRTQ-329ACN" into commit, changed ubi volumes for easier integration, slightly reworded commit message, changed ubi volume layout to use standard names all around] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add open-drain support to pinctrl-msmBrian Norris2020-09-251-0/+81
| | | | | | | | | | | | | | Submitted upstream. Shouldn't affect existing devices, but enables new device support. https://lore.kernel.org/linux-gpio/20200703080646.23233-1-computersforpeace@gmail.com/ Currently queued for-next: https://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl.git/commit/?h=for-next&id=13355ca35cd16f5024655ac06e228b3c199e52a9 Signed-off-by: Brian Norris <computersforpeace@gmail.com> [refresh patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* target: update SPDX license namesAdrian Schmutzler2020-09-228-8/+8
| | | | | | | SPDX moved from GPL-2.0 to GPL-2.0-only and from GPL-2.0+ to GPL-2.0-or-later. Reflect that in the SPDX license headers. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.66John Audia2020-09-193-14/+12
| | | | | | | | | | | | All modifications made by update_kernel.sh/no manual intervention needed Run-tested: ipq806x (R7800), ath79 (Archer C7v5), x86/64 No dmesg regressions, everything appears functional Signed-off-by: John Audia <graysky@archlinux.us> [add run test from PR] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: enable FRITZRepeater 3000 ports on switchDavid Bauer2020-09-172-3/+11
| | | | | | | | | | | | The ethernet ports on the AVM FRITZRepeater 3000 are not separated between LAN and WAN in the stock firmware. OpenWrt currently abstracts port 4 as eth0 and port 5 as eth1, bridging them in the kernel. This patch adjusts the GMAC port bitmasks and default bitmask for ar40xx to bridge them on the switch, avoiding traffic on both ports to pass thru the CPU. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: remove empty default casesAdrian Schmutzler2020-09-172-4/+0
| | | | | | There is no apparent reason to have an empty default case. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add Edgecore OAP-100 supportJohn Crispin2020-09-178-1/+527
| | | | | | | | | | | | | | | | flashing the unit * first update to latest edcore FW as per the PDF instructions * boot the initramfs - tftpboot 0x88000000 openwrt-ipq40xx-generic-edgecore_oap100-initramfs-fit-uImage.itb; bootm * inside the initramfs call the following commiands - ubiattach -p /dev/mtd0 - ubirmvol /dev/ubi0 -n0 - ubirmvol /dev/ubi0 -n1 - ubirmvol /dev/ubi0 -n2 * scp the sysupgrade image to the board and call - sysupgrade -n openwrt-ipq40xx-generic-edgecore_oap100-squashfs-nand-sysupgrade.bin Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: add Edgecore ECW5211 supportRobert Marko2020-09-177-3/+348
| | | | | | | | | | | | | | | | | This patch adds support for the Edgecore ECW5211 indoor AP. Specification: - SoC: Qualcomm Atheros IPQ4018 ARMv7-A 4x Cortex A-7 - RAM: 256MB DDR3 - NOR Flash: 16MB SPI NOR - NAND Flash: 128MB MX35LFxGE4AB SPI-NAND - Ethernet: 2 x 1G via Q8075 PHY connected to ethernet adapter via PSGMII (802.3af POE IN on eth0) - USB: 1 x USB 3.0 SuperSpeed - WLAN: Built-in IPQ4018 (2x2 802.11bng, 2x2 802.11 acn) - CC2540 BLE connected to USB 2.0 port - Atmel AT97SC3205T I2C TPM Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: essedma: enable VLAN tag offload for single-portDavid Bauer2020-09-111-8/+4
| | | | | | | | | | | | | | | | | Enable the VLAN tag offloading mechanism for RGMII single-port devices. This allows those devices to use 802.1Q VLANs on the ethernet port. Previously, RX frames were double tagged, as the RX TAG removal flag was not enabled and an additional 802.1Q header was inserted elsewhere in the code. On the TX side, tagging was completely not present for single-port devices. Enable tagging if an 802.1Q frame should be transmitted and disable the default tagging mechanism for single-port devices. Tested on Aruba AP-303 Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.61John Audia2020-08-301-2/+2
| | | | | | | | | | | | | | | | | | | Manually merged: backport-5.4 011-kbuild-export-SUBARCH.patch layerscape 701-net-0262-net-dsa-ocelot-add-tagger-for-Ocelot-Felix-switches.patch All other modifications made by update_kernel.sh Build-tested: x86/64, lantiq/xrx200, ramips/mt7621 Run-tested: ipq806x (R7800), lantiq/xrx200, x86/64, ramips (RT-AC57U) No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [minor commit message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: use wpad-basic-wolfssl as defaultPetr Štetiar2020-08-201-1/+1
| | | | | | | | | | | | | | | In order to support SAE/WPA3-Personal in default images. Replace almost all occurencies of wpad-basic and wpad-mini with wpad-basic-wolfssl for consistency. Keep out ar71xx from the list as it won't be in the next release and would only make backports harder. Build-tested (build-bot settings): ath79: generic, ramips: mt7620/mt76x8/rt305x, lantiq: xrx200/xway, sunxi: a53 Signed-off-by: Petr Štetiar <ynezz@true.cz> [rebase, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: refresh kernel 5.4 configAdrian Schmutzler2020-08-061-11/+3
| | | | | | | | | | | Refresh config with make kernel_oldconfig. After d1a8217d87bf ("kernel: clean-up build-configurable kernel config symbols"), the routine wants to add an additional CONFIG_CGROUPS (=n), which has been removed manually again, as this seems unintended. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: unify CONFIG_GPIO_SYSFS in kernel configsFelix Fietkau2020-08-062-2/+0
| | | | | | Enable it for all platforms Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: support reset button for WPJ419Phi Nguyen2020-07-231-0/+10
| | | | | | Compex WPJ419 has a reset button on a GPIO pin. Signed-off-by: Phi Nguyen <phind.uet@gmail.com>
* kernel: bump 5.4 to 5.4.52John Audia2020-07-171-14/+6
| | | | | | | | | update_kernel.sh refreshed all patches, no human interaction was needed Build system: x86_64 Run-tested: Netgear R7800 (ipq806x) Signed-off-by: John Audia <graysky@archlinux.us>
* ipq40xx: fix ethernet vlan double taggingJohn Crispin2020-07-142-11/+36
| | | | | | | | As the the SoC uses implicit vlan tagging for dual MAC support, the offload feature breaks when using double tagging. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: merge all ar40xx patches into one single patchJohn Crispin2020-07-142-30/+22
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* treewide: kernel: drop redundant USB_EHCI_HCD=n config symbolPetr Štetiar2020-07-092-2/+0
| | | | | | | | | Commit e53ec043bae1 ("kirkwood: move usb support to modules") has moved this config symbol into generic configs, so it could be removed from other configs. Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: fix patches on dts MakefileAdrian Schmutzler2020-07-082-2/+2
| | | | | | | | | The patches for arch/arm/boot/dts/Makefile have not been updated in a syntactically correct way (just body was changed). Fix it. Fixes: 4a77a060ab62 ("ipq40xx: add support for Buffalo WTR-M2133HP") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Buffalo WTR-M2133HPYanase Yuki2020-07-087-0/+451
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019. Specification ------------- - SoC: Qualcomm IPQ4019 - RAM: 512MiB - Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC) - Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch) - Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch) - Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN) - LED: 4x white LED, 4x orange LED, 1x blue LED - USB: 1x USB 3.0 port - Input: 2x tactile switch, 2x slide switch (2x SP3T) - Serial console: 115200bps, pinheader JP5 on PCB - Power: DC 12V 2A Flash instruction ----------------- 1. Set up a TFTP server (IP address: 192.168.11.10) 2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage" and put it into the TFTP server directory. 3. Connect the TFTP server and WTR-M2133HP. 4. Hold down the AOSS button, then power on the router. 5. After booting OpenWrt initramfs image, connect to the router by SSH. 6. Transfer "squashfs-nand-factory.ubi" to the router. 7. Execute the following commands. # ubidetach -p /dev/mtd15 # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi # fw_setenv bootcmd bootipq 8. Perform reboot. Recover to stock firmware ------------------------- 1. Execute the following command. # fw_setenv bootcmd bootbf 2. Reboot and wait several minutes. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add support for GL.iNet GL-S1300Dongming Han2020-07-086-3/+377
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* kernel: Update kernel 4.19 to version 4.19.131Hauke Mehrtens2020-07-041-1/+1
| | | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Run tested: ath79 Build tested: ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: set IMAGES in Device/Default definitionAdrian Schmutzler2020-06-281-27/+13
| | | | | | | | | | | | | The Device/Default definition sets a default IMAGE/sysupgrade.bin, but does not enable it by setting IMAGES. This is not consistent, and has led to IMAGES being defined at various other places in the file. Thus, this patch consolidates the default value for IMAGES by putting it in Device/Default. Since it's still overwritten where necessary, this patch is cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: consolidate DTS filesAdrian Schmutzler2020-06-2387-10517/+0
| | | | | | | | | | | | | | | The DTS files in files-4.19 and files-5.4 are exactly identical except for one file (qcom-ipq4018-emr3500.dts), which is only present for 5.4. Since there is no point in maintaining all these identical files twice, this patch moves them to the "files" directory. If there ever was a new kernel with substantial DTS changes, a new folder would need to be introduced anyway and could easily be done. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.48Petr Štetiar2020-06-221-1/+1
| | | | | | | | | | | | | | | | Resolved merge conflict in the following patches: layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch Refreshed patches, removed upstreamed patch: bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch Run tested: qemu-x86-64 Build tested: x86/64 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-162-4/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: check kernel-size for NBG6617David Bauer2020-06-141-0/+1
| | | | | | | | | The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large. Add the kernel size to validate the kernel won't be bigger than this fixed limit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add image size checks for several devicesDavid Bauer2020-06-141-3/+6
| | | | | | | This adds image size checks for various devies using an automatic mtdsplit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: use zImage for EX6100v2 and EX6150v2David Bauer2020-06-131-3/+1
| | | | | | | | | | | | | | The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA compressed images. Currently, they are using GZIP compressed kernels, which results in ledd flash being available to the root and overlay filesystems. Using a zImage results in a smaller kernel and therefore increases available space for rootfs and overlayfs. Size reduced: ~1.1 MiB Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: disable DSA and SwitchdevDENG Qingfang2020-06-132-11/+0
| | | | | | | | | | ipq40xx is still using swconfig based switch management. This might change in he future, however disable the DSA and Switchdev support for now. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [rephrased commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for EnGenius EMR3500Yen-Ting-Shen2020-06-135-1/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: essedma: Disable TCP segmentation offload for IPv6Sven Eckelmann2020-06-131-7/+4
| | | | | | | | | | | | | | | | | | | | | It was noticed that the the whole MAC can hang when transferring data from one ar40xx port (WAN ports) to the CPU and from the CPU back to another ar40xx port (LAN ports). The CPU was doing only NATing in that process. Usually, the problem first starts with a simple data corruption: $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null ... Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected. ... Read error at byte 48807936/352321536 (Decryption has failed.). Retrying. But after a short while, the whole MAC will stop to react. No traffic can be transported anymore from the CPU port from/to the AR40xx PHY/switch and the MAC has to be resetted. Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: John Crispin <john@phrozen.org>
* ipq40xx: replace "ok" with "okay" for status in DTS filesAdrian Schmutzler2020-05-1212-46/+46
| | | | | | | While "ok" is recognized in DT parsing, only "okay" is actually mentioned as valid value. Replace it accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Aruba AP-365David Bauer2020-05-1114-493/+912
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: System (red / green / amber) BTN: Reset The USB port on the device is (in contrast to other Aruba boards) real USB. The AP uses a CP2101 USB TTY converter on the board. Console baudrate is 9600 8n1. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: Make sure you use the mtd partition with the label "ubi" here! $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix alphabetical order in 02_networkDavid Bauer2020-04-241-11/+11
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.34Petr Štetiar2020-04-211-1/+1
| | | | | | | | | Refreshed patches. Run tested: qemu-x86-64, apalis, a64-olinuxino Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.33Petr Štetiar2020-04-171-1/+1
| | | | | | | | | | | | Refreshed patches, removed upstreamed patches: oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.32Petr Štetiar2020-04-141-1/+1
| | | | | | | | | | | Refreshed patches, removed upstreamed patches: generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: add support for Cell C RTL30VWPawel Dembicki2020-04-109-2/+841
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated QMI mPCIE modem. This is stripped version of ASKEY RTL0030VW. Hardware: Specification: -CPU: IPQ4019 -RAM: 256MB -Flash: NAND 128MB + NOR 16MB -WiFi: Integrated bgn/ac -LTE: mPCIe card (Modem chipset MDM9230) -LAN: 2 Gigabit Ports -USB: 2x USB2.0 -Serial console: RJ-45 115200 8n1 -Unsupported VoIP Known issues: None so far. Instruction install: There are two methods: Factory web-gui and serial + tftp. Web-gui: 1. Apply factory image via stock web-gui. Serial + initramfs: 1. Rename OpenWrt initramfs image to "image" 2. Connect serial console (115200,8n1) 3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4. 4. U-Boot commands: sf probe && sf read 0x80000000 0x180000 0x10000 setenv serverip 192.168.1.4 set fdt_high 0x85000000 tftpboot 0x84000000 image bootm 0x84000000 5. Install sysupgrade image via "sysupgrade -n" Back to stock: All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0, do firstboot and factory reset with OFW: 1. read mtd8: dd if=/dev/mtd8 of=/tmp/mtd8 2. go to tmp: cd /tmp/ 3. write first part of partition: dd if=mtd8 of=mtd8.new bs=1 count=76 4. check which layout uses bootloader: cat /proc/mtd 5a. If first are kernel_1 and rootfs_1 write 0: echo -n -e '\x00' >> mtd8.new 5b. If first are kernel and rootfs write 1: echo -n -e '\x01' >> mtd8.new 6. fill with rest of data: dd if=mtd8 bs=1 skip=77 >> mtd8.new 7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with: hexdump mtd8.new 8. write new mtd8 to flash: mtd write mtd8.new /dev/mtd8 9. do firstboot 10.reboot 11. Do back to factory defaults in OFW GUI. Based on work: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: add support for MobiPromo CM520-79FDENG Qingfang2020-04-109-2/+737
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019 Specification: SoC/Wireless: QCA IPQ4019 RAM: 512MiB Flash: 128MiB SLC NAND Ethernet PHY: QCA8075 Ethernet ports: 1x WAN, 2x LAN LEDs: 7 LEDs 2 (USB, CAN) are GPIO other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register Button: Reset Flash instruction: Disassemble the router, connect UART pins like this: GND TX RX [x x . . x .] [. . . . . .] (QCA8075 and IPQ4019 below) Baud-rate: 115200 Set up TFTP server: IP 192.168.1.188/24 Power on the router and interrupt the booting with UART console env backup (in case you want to go back to stock and need it there): printenv (Copy the output to somewhere save) Set bootenv: setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs' setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1' setenv cm520_boot 'run set_ubi; run bootkernel' setenv bootcmd 'run cm520_boot' setenv bootargs saveenv Boot initramfs from TFTP: tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb bootm After initramfs image is booted, backup rootfs partition in case of reverting to stock image cat /dev/mtd12 > /tmp/mtd12.bin Then fetch it via SCP Upload nand-factory.ubi to /tmp via SCP, then run mtd erase rootfs mtd write /tmp/*nand-factory.ubi rootfs reboot To revert to stock image, restore default bootenv in uboot UART console setenv bootcmd 'bootipq' printenv use the saved dump you did back when you installed OpenWrt to verify that there are no other differences from back in the day. saveenv upload the backed up mtd12.bin and run tftpboot mtd12.bin nand erase 0xb80000 0x7480000 nand write 0x84000000 0xb80000 0x7480000 The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead In case of this, set it back to rootfs: cd /tmp cat /dev/mtd7 > mtd7.bin echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4 for i in 28 48 68 108; do dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i done mtd write mtd7.bin BOOTCONFIG mtd write mtd7.bin BOOTCONFIG1 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [renamed volume to ubi to support autoboot, as per David Lam's test in PR#2432] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: re-add LEDS_LP5523 for the ASUS Lyra MAP-AC2200Stefan Lippers-Hollmann2020-04-092-0/+2
| | | | | | | | | | | | | | This symbol had been enabled in the initial device support submission for kernel 4.14, but apparently got lost during the v4.19 port. The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is controlled by the TI/National LP5523/55231 LED driver chip. It is left enabled in a pulsating infinite rainbow loop by the bootloader, expecting it to be reconfigured (disabled by default) after the boot process has finished and is also required to indicate failsafe/ firstboot conditions. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq40xx: fix DAP-2610 boot failurePetr Štetiar2020-03-311-0/+1
| | | | | | | | | | | | | Albert has reported, that his DAP-2610 wont boot with the latest snapshot and Fredrik has found out, that the device gets stuck at "Waiting for root device ..." due to missing 5.4 kernel config symbol CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel version bump. Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed Fixes: 272e0a702a2b ("ipq40xx: add v5.4 support") Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: switch to 5.4 kernelPetr Štetiar2020-03-281-1/+1
| | | | | | | 5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start wider userbase testing. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmuxLeon M. George2020-03-282-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | The bootloader does not always initialize the MDIO pins before booting Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul 25 2017 - 11:36:26)" this is the case when booting automatically without activating the U-Boot console. Without this change, the kernel boot will complain about missing PHYs: libphy: ipq40xx_mdio: probed ar40xx c000000.ess-switch: Probe failed - Missing PHYs! libphy: Fixed MDIO Bus: probed With this change it will work as expected: libphy: ipq40xx_mdio: probed ESS reset ok! ESS reset ok! libphy: Fixed MDIO Bus: probed Ref: GH-2835 Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Leon M. George <leon@georgemail.eu> [commit description from Fredrik, subject facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: omit IMAGE_SIZE argument from check-sizeSungbo Eo2020-03-211-7/+7
| | | | | | | | | Now that check-size uses IMAGE_SIZE by default, we can skip the argument from image recipes to reduce redundancy. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-3/+3
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move TEO governor to generic configTomasz Maciej Nowak2020-03-171-1/+0
| | | | | | | | This new symbol popped up in few places. Disable it in generic config. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed merge conflict in generic/config-5.4] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: remove maintainer variable from targetsPetr Štetiar2020-03-161-1/+0
| | | | | | | | | | | | | There is no such role as target maintainer anymore, one should always send corresponding changes for the review and anyone from the commiters is allowed to merge them or eventually use the hand break and NACK them. Lets make it clear, that it is solely a community doing the maintenance tasks. Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: 5.4: fix ethernet driverRobert Marko2020-03-161-29/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way. So lets migrate the EDMA driver to support linkmode. Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode. Now, gigabit works properly as well as ethtool. Previously you would get this in ethtool: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Now, features are properly advertised: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Robert Marko <robert.marko@sartura.hr>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-04 05:25:23 +0000