aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
...
* kernel: bump 5.4 to 5.4.52John Audia2020-07-171-14/+6
| | | | | | | | | update_kernel.sh refreshed all patches, no human interaction was needed Build system: x86_64 Run-tested: Netgear R7800 (ipq806x) Signed-off-by: John Audia <graysky@archlinux.us>
* ipq40xx: fix ethernet vlan double taggingJohn Crispin2020-07-142-11/+36
| | | | | | | | As the the SoC uses implicit vlan tagging for dual MAC support, the offload feature breaks when using double tagging. Signed-off-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: merge all ar40xx patches into one single patchJohn Crispin2020-07-142-30/+22
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* treewide: kernel: drop redundant USB_EHCI_HCD=n config symbolPetr Štetiar2020-07-092-2/+0
| | | | | | | | | Commit e53ec043bae1 ("kirkwood: move usb support to modules") has moved this config symbol into generic configs, so it could be removed from other configs. Suggested-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: fix patches on dts MakefileAdrian Schmutzler2020-07-082-2/+2
| | | | | | | | | The patches for arch/arm/boot/dts/Makefile have not been updated in a syntactically correct way (just body was changed). Fix it. Fixes: 4a77a060ab62 ("ipq40xx: add support for Buffalo WTR-M2133HP") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Buffalo WTR-M2133HPYanase Yuki2020-07-087-0/+451
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Buffalo WTR-M2133HP is a Tri-Band router based on IPQ4019. Specification ------------- - SoC: Qualcomm IPQ4019 - RAM: 512MiB - Flash Memory: NAND 128MiB (MXIC MX30LF1G18AC) - Wi-Fi: Qualcomm IPQ4019 (2.4GHz, 1ch - 13ch) - Wi-Fi: Qualcomm IPQ4019 (5GHz, 36ch - 64ch) - Wi-Fi: Qualcomm QCA9984 (2T2R, 5GHz, 100ch - 140ch) - Ethernet: 4x 10/100/1000 Mbps (1x WAN, 3x LAN) - LED: 4x white LED, 4x orange LED, 1x blue LED - USB: 1x USB 3.0 port - Input: 2x tactile switch, 2x slide switch (2x SP3T) - Serial console: 115200bps, pinheader JP5 on PCB - Power: DC 12V 2A Flash instruction ----------------- 1. Set up a TFTP server (IP address: 192.168.11.10) 2. Rename "initramfs-fit-uImage.itb" to "WTR-M2133HP-initramfs.uImage" and put it into the TFTP server directory. 3. Connect the TFTP server and WTR-M2133HP. 4. Hold down the AOSS button, then power on the router. 5. After booting OpenWrt initramfs image, connect to the router by SSH. 6. Transfer "squashfs-nand-factory.ubi" to the router. 7. Execute the following commands. # ubidetach -p /dev/mtd15 # ubiformat /dev/mtd15 -f /tmp/openwrt-ipq40xx-generic-buffalo_wtr-m2133hp-squashfs-nand-factory.ubi # fw_setenv bootcmd bootipq 8. Perform reboot. Recover to stock firmware ------------------------- 1. Execute the following command. # fw_setenv bootcmd bootbf 2. Reboot and wait several minutes. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp>
* ipq40xx: add support for GL.iNet GL-S1300Dongming Han2020-07-086-3/+377
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4029 (DAKOTA) ARM Quad-Core RAM: 512 MiB FLASH1: 16 MiB NOR - SPI0 FLASH2: 8 GiB eMMC ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4029 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4029 5GHz 802.11n/ac W2 2x2 INPUT: Reset, WPS LED: Power, Mesh, WLAN UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 UART2: On board with BLE module SPI1: On board socket for Zigbee module Install via tftp - NB: need to flash transition image firstly Firstly install transition image: (IPQ40xx) # tftpboot 0x84000000 s1300-factory-to-openwrt.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script Secondly install openwrt sysupgrade bin: (IPQ40xx) # run lf Revert to factory image: (IPQ40xx) # tftpboot 0x84000000 s1300-openwrt-to-factory.img (IPQ40xx) # sf probe && imgaddr=0x84000000 && source :script The kernel and rootfs of factory firmware are on eMMC, and openwrt firmware is on NOR flash. The transition image includes U-boot and partition table, which decides where to load kernel and rootfs. After you firstly install openwrt image, you can switch between factory and openwrt firmware by flashing transition image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* kernel: Update kernel 4.19 to version 4.19.131Hauke Mehrtens2020-07-041-1/+1
| | | | | | | | | | | | | Fixes: - CVE-2020-10757 The "mtd: rawnand: Pass a nand_chip object to nand_release()" commit was backported which needed some adaptations to other code. Run tested: ath79 Build tested: ath79 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: set IMAGES in Device/Default definitionAdrian Schmutzler2020-06-281-27/+13
| | | | | | | | | | | | | The Device/Default definition sets a default IMAGE/sysupgrade.bin, but does not enable it by setting IMAGES. This is not consistent, and has led to IMAGES being defined at various other places in the file. Thus, this patch consolidates the default value for IMAGES by putting it in Device/Default. Since it's still overwritten where necessary, this patch is cosmetic. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: consolidate DTS filesAdrian Schmutzler2020-06-2387-10517/+0
| | | | | | | | | | | | | | | The DTS files in files-4.19 and files-5.4 are exactly identical except for one file (qcom-ipq4018-emr3500.dts), which is only present for 5.4. Since there is no point in maintaining all these identical files twice, this patch moves them to the "files" directory. If there ever was a new kernel with substantial DTS changes, a new folder would need to be introduced anyway and could easily be done. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.48Petr Štetiar2020-06-221-1/+1
| | | | | | | | | | | | | | | | Resolved merge conflict in the following patches: layerscape: 701-net-0213-dpaa2-eth-Add-CEETM-qdisc-support.patch ramips: 0013-owrt-hack-fix-mt7688-cache-issue.patch Refreshed patches, removed upstreamed patch: bcm63xx: 020-v5.8-mtd-rawnand-brcmnand-fix-hamming-oob-layout.patch Run tested: qemu-x86-64 Build tested: x86/64 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: drop shebang from non-executable target filesAdrian Schmutzler2020-06-162-4/+0
| | | | | | | | | | | | | | This drops the shebang from all target files for /lib and /etc/uci-defaults folders, as these are sourced and the shebang is useless. While at it, fix the executable flag on a few of these files. This does not touch ar71xx, as this target is just used for backporting now and applying cosmetic changes would just complicate things. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: check kernel-size for NBG6617David Bauer2020-06-141-0/+1
| | | | | | | | | The ZyXEL NBG6617 has a separate kernel partition which is 4MiB large. Add the kernel size to validate the kernel won't be bigger than this fixed limit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add image size checks for several devicesDavid Bauer2020-06-141-3/+6
| | | | | | | This adds image size checks for various devies using an automatic mtdsplit. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: use zImage for EX6100v2 and EX6150v2David Bauer2020-06-131-3/+1
| | | | | | | | | | | | | | The NETGEAR EX61500v2 and EX6150v2 U-Boot does not support booting LZMA compressed images. Currently, they are using GZIP compressed kernels, which results in ledd flash being available to the root and overlay filesystems. Using a zImage results in a smaller kernel and therefore increases available space for rootfs and overlayfs. Size reduced: ~1.1 MiB Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: disable DSA and SwitchdevDENG Qingfang2020-06-132-11/+0
| | | | | | | | | | ipq40xx is still using swconfig based switch management. This might change in he future, however disable the DSA and Switchdev support for now. Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [rephrased commit message] Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for EnGenius EMR3500Yen-Ting-Shen2020-06-135-1/+265
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 (2 ports) USB: 1 x 2.0 (Host controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: White, Blue, Red, Orange Flash instruction: From EnGenius firmware to OpenWrt firmware: In Firmware Upgrade page, upgrade your openwrt-ipq40xx-generic-engenius_emr3500-squashfs-factory.bin directly. From OpenWrt firmware to EnGenius firmware: 1. Setup a TFTP server on your computer and configure static IP to 192.168.99.8 Put the EnGenius firmware in the TFTP server directory on your computer. 2. Power up EMR3500. Press 4 and then press any key to enter u-boot. 3. Download EnGenius firmware (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-emr3500-nor-fw-s.img 4. Flash the firmware (IPQ40xx) # imgaddr=0x84000000 && source 0x84000000:script 5. Reboot (IPQ40xx) # reset Signed-off-by: Yen-Ting-Shen <frank.shen@senao.com> [squashed update patch, updated to 5.4, dropped BOARD_NAME, migrated to SOC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: essedma: Disable TCP segmentation offload for IPv6Sven Eckelmann2020-06-131-7/+4
| | | | | | | | | | | | | | | | | | | | | It was noticed that the the whole MAC can hang when transferring data from one ar40xx port (WAN ports) to the CPU and from the CPU back to another ar40xx port (LAN ports). The CPU was doing only NATing in that process. Usually, the problem first starts with a simple data corruption: $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null ... Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected. ... Read error at byte 48807936/352321536 (Decryption has failed.). Retrying. But after a short while, the whole MAC will stop to react. No traffic can be transported anymore from the CPU port from/to the AR40xx PHY/switch and the MAC has to be resetted. Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: John Crispin <john@phrozen.org>
* ipq40xx: replace "ok" with "okay" for status in DTS filesAdrian Schmutzler2020-05-1212-46/+46
| | | | | | | While "ok" is recognized in DT parsing, only "okay" is actually mentioned as valid value. Replace it accordingly. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Aruba AP-365David Bauer2020-05-1114-493/+912
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- SoC: Qualcomm IPQ4029 RAM: 512M DDR3 FLASH: - 128MB NAND (Macronix MX30LF1G18AC) - 4MB SPI-NOR (Macronix MX25R3235F) TPM: Atmel AT97SC3203 BLE: Texas Instruments CC2540T attached to ttyMSM0 ETH: Atheros AR8035 LED: System (red / green / amber) BTN: Reset The USB port on the device is (in contrast to other Aruba boards) real USB. The AP uses a CP2101 USB TTY converter on the board. Console baudrate is 9600 8n1. To enable a full list of commands in the U-Boot "help" command, execute the literal "diag" command. Installation ------------ 1. Get the OpenWrt initramfs image. Rename it to ipq40xx.ari and put it into the TFTP server root directory. Configure the TFTP server to be reachable at 192.168.1.75/24. Connect the machine running the TFTP server to the ethernet port of the access point. 2. Connect to the serial console. Interrupt autobooting by pressing Enter when prompted. 3. Configure the bootargs and bootcmd for OpenWrt. $ setenv bootargs_openwrt "setenv bootargs console=ttyMSM1,9600n8" $ setenv nandboot_openwrt "run bootargs_openwrt; ubi part aos1; ubi read 0x85000000 kernel; bootm 0x85000000" $ setenv ramboot_openwrt "run bootargs_openwrt; setenv ipaddr 192.168.1.105; setenv serverip 192.168.1.75; netget; set fdt_high 0x87000000; bootm" $ setenv bootcmd "run nandboot_openwrt" $ saveenv 4. Load OpenWrt into RAM: $ run ramboot_openwrt 5. After OpenWrt booted, transfer the OpenWrt sysupgrade image to the /tmp folder on the device. 6. Flash OpenWrt: Make sure you use the mtd partition with the label "ubi" here! $ ubidetach -p /dev/mtd1 $ ubiformat /dev/mtd1 $ sysupgrade -n /tmp/openwrt-sysupgrade.bin To go back to the stock firmware, simply reset the bootcmd in the bootloader to the original value: $ setenv bootcmd "boot" $ saveenv Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix alphabetical order in 02_networkDavid Bauer2020-04-241-11/+11
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 5.4 to 5.4.34Petr Štetiar2020-04-211-1/+1
| | | | | | | | | Refreshed patches. Run tested: qemu-x86-64, apalis, a64-olinuxino Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.33Petr Štetiar2020-04-171-1/+1
| | | | | | | | | | | | Refreshed patches, removed upstreamed patches: oxnas: 001-irqchip-versatile-fpga-Handle-chained-IRQs-properly.patch oxnas: 002-irqchip-versatile-fpga-Apply-clear-mask-earlier.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.4 to 5.4.32Petr Štetiar2020-04-141-1/+1
| | | | | | | | | | | Refreshed patches, removed upstreamed patches: generic: 746-stable-net-dsa-mt7530-fix-null-pointer-dereferencing-in-por.patch Run tested: qemu-x86-64, apalis Build tested: x86/64, imx6, sunxi/a53 Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: add support for Cell C RTL30VWPawel Dembicki2020-04-109-2/+841
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Cell C RTL30VW is a LTE router with tho gigabit ethernets and integrated QMI mPCIE modem. This is stripped version of ASKEY RTL0030VW. Hardware: Specification: -CPU: IPQ4019 -RAM: 256MB -Flash: NAND 128MB + NOR 16MB -WiFi: Integrated bgn/ac -LTE: mPCIe card (Modem chipset MDM9230) -LAN: 2 Gigabit Ports -USB: 2x USB2.0 -Serial console: RJ-45 115200 8n1 -Unsupported VoIP Known issues: None so far. Instruction install: There are two methods: Factory web-gui and serial + tftp. Web-gui: 1. Apply factory image via stock web-gui. Serial + initramfs: 1. Rename OpenWrt initramfs image to "image" 2. Connect serial console (115200,8n1) 3. Set IP to different than 192.168.1.11, but 24 bit mask, eg. 192.168.1.4. 4. U-Boot commands: sf probe && sf read 0x80000000 0x180000 0x10000 setenv serverip 192.168.1.4 set fdt_high 0x85000000 tftpboot 0x84000000 image bootm 0x84000000 5. Install sysupgrade image via "sysupgrade -n" Back to stock: All is needed is swap 0x4c byte in mtd8 from 0 to 1 or 1 to 0, do firstboot and factory reset with OFW: 1. read mtd8: dd if=/dev/mtd8 of=/tmp/mtd8 2. go to tmp: cd /tmp/ 3. write first part of partition: dd if=mtd8 of=mtd8.new bs=1 count=76 4. check which layout uses bootloader: cat /proc/mtd 5a. If first are kernel_1 and rootfs_1 write 0: echo -n -e '\x00' >> mtd8.new 5b. If first are kernel and rootfs write 1: echo -n -e '\x01' >> mtd8.new 6. fill with rest of data: dd if=mtd8 bs=1 skip=77 >> mtd8.new 7. CHECK IF mtd8.new HAVE CHANGED ONLY ONE BYTE! e.g with: hexdump mtd8.new 8. write new mtd8 to flash: mtd write mtd8.new /dev/mtd8 9. do firstboot 10.reboot 11. Do back to factory defaults in OFW GUI. Based on work: Cezary Jackiewicz <cezary@eko.one.pl> Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: add support for MobiPromo CM520-79FDENG Qingfang2020-04-109-2/+737
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | MobiPromo CM520-79F is an AC1300 dual band router based on IPQ4019 Specification: SoC/Wireless: QCA IPQ4019 RAM: 512MiB Flash: 128MiB SLC NAND Ethernet PHY: QCA8075 Ethernet ports: 1x WAN, 2x LAN LEDs: 7 LEDs 2 (USB, CAN) are GPIO other 5 (2.4G, 5G, LAN1, LAN2, WAN) are connected to a shift register Button: Reset Flash instruction: Disassemble the router, connect UART pins like this: GND TX RX [x x . . x .] [. . . . . .] (QCA8075 and IPQ4019 below) Baud-rate: 115200 Set up TFTP server: IP 192.168.1.188/24 Power on the router and interrupt the booting with UART console env backup (in case you want to go back to stock and need it there): printenv (Copy the output to somewhere save) Set bootenv: setenv set_ubi 'set mtdids nand0=nand0; set mtdparts mtdparts=nand0:0x7480000@0xb80000(fs); ubi part fs' setenv bootkernel 'ubi read 0x84000000 kernel; bootm 0x84000000#config@1' setenv cm520_boot 'run set_ubi; run bootkernel' setenv bootcmd 'run cm520_boot' setenv bootargs saveenv Boot initramfs from TFTP: tftpboot openwrt-ipq40xx-generic-mobipromo_cm520-79f-initramfs-fit-zImage.itb bootm After initramfs image is booted, backup rootfs partition in case of reverting to stock image cat /dev/mtd12 > /tmp/mtd12.bin Then fetch it via SCP Upload nand-factory.ubi to /tmp via SCP, then run mtd erase rootfs mtd write /tmp/*nand-factory.ubi rootfs reboot To revert to stock image, restore default bootenv in uboot UART console setenv bootcmd 'bootipq' printenv use the saved dump you did back when you installed OpenWrt to verify that there are no other differences from back in the day. saveenv upload the backed up mtd12.bin and run tftpboot mtd12.bin nand erase 0xb80000 0x7480000 nand write 0x84000000 0xb80000 0x7480000 The BOOTCONFIG may have been configured to boot from alternate partition (rootfs_1) instead In case of this, set it back to rootfs: cd /tmp cat /dev/mtd7 > mtd7.bin echo -ne '\x0b' | dd of=mtd7.bin conv=notrunc bs=1 count=1 seek=4 for i in 28 48 68 108; do dd if=/dev/zero of=mtd7.bin conv=notrunc bs=1 count=1 seek=$i done mtd write mtd7.bin BOOTCONFIG mtd write mtd7.bin BOOTCONFIG1 Signed-off-by: DENG Qingfang <dengqf6@mail2.sysu.edu.cn> [renamed volume to ubi to support autoboot, as per David Lam's test in PR#2432] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: re-add LEDS_LP5523 for the ASUS Lyra MAP-AC2200Stefan Lippers-Hollmann2020-04-092-0/+2
| | | | | | | | | | | | | | This symbol had been enabled in the initial device support submission for kernel 4.14, but apparently got lost during the v4.19 port. The ASUS Lyra MAP-AC2200 has a single (very bright) rgb LED, which is controlled by the TI/National LP5523/55231 LED driver chip. It is left enabled in a pulsating infinite rainbow loop by the bootloader, expecting it to be reconfigured (disabled by default) after the boot process has finished and is also required to indicate failsafe/ firstboot conditions. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de>
* ipq40xx: fix DAP-2610 boot failurePetr Štetiar2020-03-311-0/+1
| | | | | | | | | | | | | Albert has reported, that his DAP-2610 wont boot with the latest snapshot and Fredrik has found out, that the device gets stuck at "Waiting for root device ..." due to missing 5.4 kernel config symbol CONFIG_MTD_SPLIT_WRGG_FW which was probably lost during the kernel version bump. Ref: https://forum.openwrt.org/t/dap-2610-bricked-help-needed Fixes: 272e0a702a2b ("ipq40xx: add v5.4 support") Suggested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: switch to 5.4 kernelPetr Štetiar2020-03-281-1/+1
| | | | | | | 5.4.24 seems to be working fine on my zyxel,nbg6617, so let's start wider userbase testing. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: wpj428: fix missing MDIO GPIO reset and pinmuxLeon M. George2020-03-282-0/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | The bootloader does not always initialize the MDIO pins before booting Linux. E.g. on version "U-Boot 2012.07 [Chaos Calmer 15.05.1,r35193] (Jul 25 2017 - 11:36:26)" this is the case when booting automatically without activating the U-Boot console. Without this change, the kernel boot will complain about missing PHYs: libphy: ipq40xx_mdio: probed ar40xx c000000.ess-switch: Probe failed - Missing PHYs! libphy: Fixed MDIO Bus: probed With this change it will work as expected: libphy: ipq40xx_mdio: probed ESS reset ok! ESS reset ok! libphy: Fixed MDIO Bus: probed Ref: GH-2835 Tested-by: Fredrik Olofsson <fredrik.olofsson@anyfinetworks.com> Signed-off-by: Leon M. George <leon@georgemail.eu> [commit description from Fredrik, subject facelift] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: omit IMAGE_SIZE argument from check-sizeSungbo Eo2020-03-211-7/+7
| | | | | | | | | Now that check-size uses IMAGE_SIZE by default, we can skip the argument from image recipes to reduce redundancy. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: gather DEVICE_VARS into one placeSungbo Eo2020-03-211-3/+3
| | | | | | | | | | | Place DEVICE_VARS assignments at the top of the file or above Device/Default to make them easier to find. For ramips, remove redundant values already present in parent file. Signed-off-by: Sungbo Eo <mans0n@gorani.run> [do not touch ar71xx, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: move TEO governor to generic configTomasz Maciej Nowak2020-03-171-1/+0
| | | | | | | | This new symbol popped up in few places. Disable it in generic config. Signed-off-by: Tomasz Maciej Nowak <tomek_n@o2.pl> [fixed merge conflict in generic/config-5.4] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* treewide: remove maintainer variable from targetsPetr Štetiar2020-03-161-1/+0
| | | | | | | | | | | | | There is no such role as target maintainer anymore, one should always send corresponding changes for the review and anyone from the commiters is allowed to merge them or eventually use the hand break and NACK them. Lets make it clear, that it is solely a community doing the maintenance tasks. Signed-off-by: Petr Štetiar <ynezz@true.cz> Acked-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: 5.4: fix ethernet driverRobert Marko2020-03-161-29/+36
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way. So lets migrate the EDMA driver to support linkmode. Also, old get/set settings API for ethtool is also dropped so lets convert to new ksettings API while at it as it demands linkmode. Now, gigabit works properly as well as ethtool. Previously you would get this in ethtool: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Now, features are properly advertised: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Half 1000baseT/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: 5.4: fix networking PHY driverRobert Marko2020-03-162-14/+3
| | | | | | | | In 5.4 kernel old u32 array way of setting network features was dropped and linkmode is now the only way. So lets migrate the PHY driver to support linkmode. Also, now in order for gigabit to work, PHY driver needs to advertise PHY_GBIT_FEATURES instead of PHY_BASIC_FEATURES Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: 5.4: fix of_get_mac_address obsolete usage OOPsPetr Štetiar2020-03-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | of_get_mac_address returns valid pointer or ERR_PTR since 5.2 via commit d01f449c008a ("of_net: add NVMEM support to of_get_mac_address") so the patch fixes following OOPs on nbg6617: Unable to handle kernel paging request at virtual address ffffffed CPU: 1 PID: 1 Comm: swapper/0 Not tainted 5.4.24 #0 PC is at edma_axi_probe+0x444/0x1114 LR is at bus_find_device+0x88/0x9c Where the PC can be resolved to: >>> l *edma_axi_probe+0x444 0xc067be5c is in edma_axi_probe (./include/linux/string.h:378). >>> l *edma_axi_probe+0x43f 0xc067be57 is in edma_axi_probe (drivers/net/ethernet/qualcomm/essedma/edma_axi.c:936) Which leads to the following code fragment: 935 mac_addr = of_get_mac_address(pnp); 936 if (mac_addr) 937 memcpy(edma_netdev[idx_mac]->dev_addr, mac_addr, ETH_ALEN); Where using mac_addr=0xffffffed (-ENODEV) as source address in memcpy() is causing the OOPs. Acked-by: John Crispin <john@phrozen.org> Signed-off-by: Petr Štetiar <ynezz@true.cz>
* ipq40xx: 5.4: enable NANDRobert Marko2020-03-151-0/+5
| | | | | | | | | | Lets enable RAW NAND and Qcom NANDC drivers again in kernel 5.4. They were dropped when 5.4 support was introduced due to upstream changing the symbol names so refreshing was not enough. Signed-off-by: Robert Marko <robert.marko@sartura.hr> [cut long line in commit message, enabled BCH as well] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* generic: 4.19: Add 4B_OPCODES flag to w25q256Robert Marko2020-03-121-27/+0
| | | | | | This patch backports the upstream patch that adds the 4B_OPCODES flag to w25q256 under 4.19 kernel. This is needed for ipq40xx and ramips. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: Remove kernel 4.14 supportHauke Mehrtens2020-03-1281-22206/+0
| | | | | | | | | This target was switched to kernel 4.19 more than 6 months ago in commit f342ffd300da ("treewide: kernel: bump some targets to 4.19") and now with kernel 5.4 support being added it gets harder to support kernel 4.14 in addition to kernel 4.19 and 5.4. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: replace ${} with $()Sungbo Eo2020-03-111-3/+3
| | | | | | ${} and $() are exactly the same. Follow the convention of using $(). Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: add cpximg to flash Compex WPJ428 via bootloaderLeon M. George2020-03-101-1/+18
| | | | | | | | | | | | | | | | | | | | | | Generate a cpximg that is compatible with the cpximg loader in Compex' u-boot. The cpximg loader can be started either by holding the reset button during power up or by entering the u-boot prompt and entering 'cpximg'. Once it's running, a TFTP-server under 192.168.1.1 will accept an image appropriate for the board revision that is etched on the board (e.g. 6A04). The image can be pushed using tftp: tftp -v -m binary 192.168.1.1 -c put openwrt-ipq40xx-generic-compex_wpj428-squashfs-cpximg-6a04.bin cpximg files can also be used with the sysupgrade utility in stock images. (add SSH key in luci for root access) In mkmylofw_32m, the calculation of the "partition size" has been preferred to just padding the partition as this will result in less block transfers during flashing (while the additional complexity is bearable). Signed-off-by: Leon M. George <leon@georgemail.eu> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: 5.4: move some kconfig options to genericYousong Zhou2020-03-101-6/+0
| | | | | | | | | | | CONFIG_64BIT_TIME=y CONFIG_KASAN_STACK=1 CONFIG_UBSAN_ALIGNMENT=y CONFIG_UNIX_SCM=y CONFIG_DMA_DECLARE_COHERENT=y CONFIG_OF_RESERVED_MEM=y Signed-off-by: Yousong Zhou <yszhou4tech@gmail.com>
* kernel: bump 5.4 to 5.4.24Koen Vandeputte2020-03-091-2/+2
| | | | | | | | | Refreshed all patches. Compile-tested on: imx6 Runtime-tested on: imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.19 to 4.19.108Koen Vandeputte2020-03-092-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.172Koen Vandeputte2020-03-091-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: add support for 8devices Habanero DVKRobert Marko2020-03-098-2/+763
| | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the 8devices Habanero development board. Specs are: CPU: QCA IPQ4019 RAM: DDR3L 512MB Storage: 32MB SPI-NOR and optional Parallel SLC NAND(Some boards ship with it and some without) WLAN1: 2.4 GHz built into IPQ4019 (802.11n) 2x2 WLAN2: 5 GHz built into IPO4019 (802.11ac Wawe-2) 2x2 Ethernet: 5x Gbit LAN (QCA 8075) USB: 1x USB 2.0 and 1x USB 3.0 (Both built into IPQ4019) MicroSD slot (Uses SD controller built into IPQ4019) SDIO3.0/EMMC slot (Uses the same SD controller) Mini PCI-E Gen 2.0 slot (Built into IPQ4019) 5x LEDs (4 GPIO controllable) 2x Pushbutton (1 is connected to GPIO, other to SoC reset) LCD ZIF socket (Uses the LCD controller built into IPQ4019 which has no driver support) 1x UART 115200 rate on J18 2x breakout development headers 12V DC Jack for power DIP switch for bootstrap configuration Installation instructions: Since boards ship with vendors fork of OpenWrt sysupgrade can be used. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add IPQ4019 SD/MMC controller supportRobert Marko2020-03-0917-22/+520
| | | | | | | | | | This commit finally adds support for the built in SD/MMC controller in IPQ4019 SoC. Controller is supported by the upstream SDHCI-MSM driver with a minor clock setting patch. Patch is special to the IPQ4019 and cannot be upstreamed. LDO and SDHCI node are upstreamed, and LDO node is awaiting to be accepted. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: fix support of EnGenius EAP2200Adrian Schmutzler2020-03-053-21/+21
| | | | | | | | | | | | This fixes a typo in the device string for MAC address setup in 02_network and corrects the indent in the device's DTS files. While at it, move the aliases section before the keys section to have it closer to the top of the file. Fixes: a736d912e2ba ("ipq40xx: add support for EnGenius EAP2200") Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: move commonly disabled symbols to generic configDavid Bauer2020-03-011-4/+0
| | | | | | | Move new commonly disabled kernel 5.4 symbols to the generic kernel configuration. Signed-off-by: David Bauer <mail@david-bauer.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-17 20:02:50 +0000