aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: Linksys MR8300: fix the USB port powerDaniel González Cabanelas2023-02-251-1/+11
| | | | | | | | | | | | | The USB port on the MR8300 randomly fails to feed bus-powered devices. This is caused by a misconfigured pinmux. The GPIO68 should be used to enable the USB power (active low), but it's inside the NAND pinmux. This GPIO pin was found in the original firmware at a startup script in both MR8300 and EA8300. Therefore apply the fix for both boards. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: chromium: Enable kmod-ramoops by defaultBrian Norris2023-02-181-1/+5
| | | | | | | | Chromium devices (like Google WiFi) have ramoops memory reserved by the bootloader. Let's enable the ramoops kernel module by default, so we get better crash logging. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* treewide: replace /sys/devices/virtual/ubi by /sys/class/ubiDaniel Golle2023-02-151-1/+1
| | | | | | | | | | Starting from Linux Kernel version 6.3 UBI devices will no longer be considered virtual, but rather have an MTD device parent. Hence they will no longer be listed under /sys/devices/virtual/ubi which is used in multiple places in OpenWrt. Prepare for future kernels by using /sys/class/ubi instead of /sys/devuces/virtual/ubi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: fix dts whitespaceFelix Baumann2023-02-092-2/+2
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq4019: fix dts white-spaceFelix Baumann2023-02-088-438/+438
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq40xx: fix assignment of lan port numbers for Cell C RTL30VWCezary Jackiewicz2023-02-061-2/+2
| | | | | | After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-041-1/+1
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: convert Extreme AP3915i to DSAJames Andrewartha2023-01-173-2/+16
| | | | | | Convert and re-enabled Extreme AP3915i to DSA. Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
* ipq40xx: add DSL support for FritzBox 7530Martin Schiller2023-01-164-6/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up MAC, LED, settings and default packages for DSL usage, similar to the lantiq target. Due to licensing uncertainty, we do not include the firmware files for the DSL drivers. To have a working DSL setup, follow the instructions below. Download the firmware files locally: mkdir -p files/lib/firmware/09a9 wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin For people building their own images: Run the above commands in the root of your local OpenWrt clone, and the firmware files will be part of the resulting images. For people downloading images: Copy the firmware files onto the router once it's booted up: scp -O -r files/lib/firmware root@fritz:/lib Reboot the device afterwards. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [cleaned up] Signed-off-by: Andre Heider <a.heider@gmail.com> [set up LED] Signed-off-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: fritzbox-7530.dts: increase dma coherent pool sizeMartin Schiller2023-01-161-0/+4
| | | | | | | This is needed by the mei driver to be able to download the firmware. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add Intel/Lantiq ATM hacksMartin Schiller2023-01-162-0/+180
| | | | | | | | | | Similar to the lantiq platform, these are required for DSL support. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [switch to kernel 5.10 and 5.15] Signed-off-by: Jan Hoffmann <jan@3e8.eu> [update patches based on UGW 8.5.2.10, remove 5.10 support] Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-155-2/+541
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-144-0/+498
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* kernel: bump 5.15 to 5.15.87John Audia2023-01-131-1/+1
| | | | | | | | | | | | | Removed upstreamed: generic/hack-5.15/290-net-dsa-mv88e6xxx-depend-on-PTP-conditionally.patch[1] Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.87&id=945e58bdaf6faf6e3f957d182244fa830acddab4 Signed-off-by: John Audia <therealgraysky@proton.me>
* Revert "TODROP: test for ipq4019 target"Christian Marangi2023-01-111-1/+1
| | | | | | | | This reverts commit 4eb587f7e0a49b9c404857b18571f45981b3a7fc. Pushed by mistake while merging a pr using script. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* TODROP: test for ipq4019 targetChristian Marangi2023-01-111-1/+1
| | | | | | COMMIT TO DROP Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* treewide: update NVMEM symbolsRafał Miłecki2023-01-071-1/+1
| | | | | Fixes: 8dfe69cdfc5c ("kernel: update nvmem subsystem to the latest upstream") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* generic: fix silicon labs spidev bindingsVincent Tremblay2023-01-062-2/+2
| | | | | | | | | | | | | | | Fix Silicon Labs bindings in the spidev driver Some bindings for Silicon Labs chips already exists upstream. These bindings can be found in trivial-devices.yaml. The existing bindings are using "silabs" instead of "siliconlabs" to identify the manufacturer. This commit add two submitted patches for silabs chips and rename the manufacturer in the different DTS for more coherence. Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: fix wlan mac address for Aruba AP-303HBjoern Dobe2023-01-041-4/+6
| | | | | | | | | | | Assigns the correct mac address from nvmen to the wlan interfaces. This Mac address corresponds to the label "Wireless MAC" on the device and the stock firmware. Removes duplicate entry of calibration variant for both radios. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
* ipq40xx: delete files used for building 5.10 kernelNick Hainke2023-01-0325-2442/+0
| | | | | | | The kernel 5.15 now defaults. Remove unnecessary files. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2022-12-311-0/+18
| | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-313-2/+22
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-314-11/+8
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-314-23/+38
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-293-2/+34
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: fix usb driver not loaded for GL-A1300Weiping Yang2022-12-111-0/+8
| | | | | | | This patch enables USB support for the GL.iNet GL-A1300 Repair the usb driver startup phase is not loaded Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-279-217/+347
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: remove '-fit' string from kernel filenamesDaniel Golle2022-11-241-4/+4
| | | | | | | | The type of those images is already distinguishable by the '.itb' extension, there is no need for an additional '-fit' string in the filenames. Remove it to behave more like other targets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove 'nand-' string from image filenamesDaniel Golle2022-11-242-16/+16
| | | | | | | | | Only on the ipq40xx subtarget different filenames were used for NAND- based devices. This is unneeded, confusing and breaks downstream tools such as luci-app-attendedsysupgrade and auc. Remove the 'nand-' string from image filenames to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: dts: remove leftover nodes after DSA conversionLech Perczak2022-11-133-29/+1
| | | | | | | | | | | | | | Remove ess-psgmii@98000, edma@c080000 and ess-switch@c000000 nodes. These nodes are not used after the DSA conversion, but were left over in a few devices added recently. ZTE MF289F is omitted on purpose, as for it, these nodes will be removed together with DSA conversion. Build tested only, as I only have MF286D from those devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-133-7/+32
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa2200Sven Eckelmann2022-11-132-7/+40
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-133-6/+33
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for plasmacloud,pa1200Sven Eckelmann2022-11-132-2/+31
| | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a62Sven Eckelmann2022-11-124-10/+45
| | | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: utilize nvmem-cells for openmesh,a42Sven Eckelmann2022-11-124-4/+38
| | | | | | | | | | | | | | | The calibration data and mac addresses on this device are stored in the 0:ART partition. It is therefore possible to move the code to handle them directly to the devicetree instead of the various scripts. But the actual relevant information about the partition layout is provided by the bootloader via bootargs (mtdparts) and not via the devicetree itself. Instead of using a fixed-partition template, the mtd dynamic partitions support from the upstream kernel is used. Reported-by: Robert Marko <robert.marko@sartura.hr> Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a62 to DSASven Eckelmann2022-11-124-9/+29
| | | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a42 to DSASven Eckelmann2022-11-124-6/+33
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: D-Link DAP-2610: convert to DSAGuillaume Lefebvre2022-11-123-2/+16
| | | | | | | Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-094-0/+342
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for MikroTik hAP ac3 LTE6 kitCsaba Sipos2022-10-307-1/+341
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD (hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac wireless AP with built-in Mini PCI-E LTE modem, one USB port, five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac3_lte6_kit for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port - 1x USB Type A port - 1x Mini PCI-E port (supporting USB) - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6) Installation: Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6). 0. Export your MikroTik license key (in case you want to use the device with RouterOS later) 1. Boot the initramfs image via TFTP 2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder 3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin 4. Recovery to factory software is possible via Netinstall: https://help.mikrotik.com/docs/display/ROS/Netinstall Signed-off-by: Csaba Sipos <metro4@freemail.hu>
* kernel: bump 5.15 to 5.15.75John Audia2022-10-302-3/+3
| | | | | | | | | | | | | | | | | | | | | Removed upstreamed: bcm27xx/patches-5.15/950-0446-drm-vc4-Fix-timings-for-VEC-modes.patch[1] Manually rebased: patches-5.15/950-0600-xhci-quirks-add-link-TRB-quirk-for-VL805.patch bcm27xx/patches-5.15/950-0606-usb-xhci-add-VLI_TRB_CACHE_BUG-quirk.patch bcm27xx/patches-5.15/950-0717-usb-xhci-add-a-quirk-for-Superspeed-bulk-OUT-transfe.patch bcm53xx/patches-5.15/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All other patches automatically rebased 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.75&id=2810061452f9b748b096ad023d318690ca519aa3 Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.10 to 5.10.150John Audia2022-10-301-1/+1
| | | | | | | | | | | Manually rebased: bcm53xx/patches-5.10/180-usb-xhci-add-support-for-performing-fake-doorbell.patch All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me> [Move gro_skip in 680-NET-skip-GRO-for-foreign-MAC-addresses.patch to old position] Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: convert to DSA and enable Netgear Orbi devicesDavide Fioravanti2022-10-253-8/+51
| | | | | | | | | | Convert to DSA and enable again Netgear Orbi devices: - RBR50 - RBS50 - SRR60 - SRS60 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: Convert Google Wifi to DSA, reenableBrian Norris2022-10-233-2/+48
| | | | | | | | | | | | | | | | Undo parts of these: 116feb4a1cad ipq40xx: remove non-converted network configs db19efee9512 ipq40xx: disable boards not converted to DSA Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock bootloader has memorized them (instead of following aliases); then plug the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the 'local-mac-address' property is no longer in the correct node. Cc: David Bauer <mail@david-bauer.net> Cc: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* ipq40xx: convert to DSA and enable mobipromo,cm520-79fJack Chen2022-10-234-6/+36
| | | | | | | Convert to DSA and enable the MobiPromo CM520-79F device again. Signed-off-by: Jack Chen <redchenjs@live.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: convert to DSA and enable asus,rt-ac42uChen Minqiang2022-10-225-20/+45
| | | | | | | This convert board asus,rt-ac42u to DSA and re-enable it Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq40xx: Convert mikrotik,wap-ac to DSAMark Mentovai2022-10-194-6/+26
| | | | | | | | | | | | | | | | | | As done previously, this preserves the MAC addresses of they physical Ethernet ports. The interfaces are renamed as eth0 is in use for the native GMAC; the new interface naming matches the physical port labels. - sw-eth1 corresponds to the physical port labeled ETH1 and has the base MAC address. This port can be used to power the device. - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC address one greater than the base. As this device has 2 physical ports, they are each connected to their respective PHYs, allowing the link status to be visible to software. Since they are not marked on the case with any role (such as LAN or WAN), both are bridged to the lan network by default, although this can easily be changed if needed. Signed-off-by: Mark Mentovai <mark@mentovai.com>
* ipq40xx: Fix wrong GPIO for internal status LED on ZTE MF289FGiammarco Marzano2022-10-121-1/+1
| | | | | | | | Change GPIO from 10 to 35 to make it works as expected Fixes: 0de6a3339f1a ("ipq40xx: Add ZTE MF289F") Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: convert to DSA and enable Sony NCP-HG100/CellularINAGAKI Hiroshi2022-10-094-19/+23
| | | | | | | This patch converts networking on Sony NCP-HG100/Cellular to DSA and re-enables support for the device. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-10-31 21:31:54 +0000