aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: 5.15: add patch commenting unused sdhci functionChristian Marangi2023-05-121-0/+108
| | | | | | | | | | | | Add patch commenting unused sdhci function, hopin this will be dropped when the problem is actually found. Fix compilation warning: drivers/mmc/host/sdhci-msm.c:1781:13: error: 'sdhci_msm_set_clock' defined but not used [-Werror=unused-function] 1781 | static void sdhci_msm_set_clock(struct sdhci_host *host, unsigned int clock) | ^~~~~~~~~~~~~~~~~~~ cc1: all warnings being treated as errors Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: add PSGMII PHY mode to phylink_get_linkmodes()Robert Marko2023-05-121-4/+12
| | | | | | | | | | | | | | | Upstream commit ("net: phylink: add generic validate implementation") was backported, however PSGMII PHY mode patch for ipq40xx was not updated to add PSGMII to phylink_get_linkmodes() so the following warning would be printed during kernel compilation: drivers/net/phy/phylink.c: In function 'phylink_get_linkmodes': drivers/net/phy/phylink.c:360:9: error: enumeration value 'PHY_INTERFACE_MODE_PSGMII' not handled in switch [-Werror=switch] 360 | switch (interface) { | ^~~~~~ Resolve the warning by adding the PSGMII mode to phylink_get_linkmodes(). Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: improve handling of CONFIG_IO_URINGTony Ambardar2023-05-031-1/+0
| | | | | | | | | | | | | | | | | | | | | | Kernel setting CONFIG_IO_URING supports high-performance I/O for file access and servers, generally for more performant platforms, and adds ~45 KB to kernel sizes. The need for this on less "beefy" devices is questionable, as is the size cost considering many platforms have kernel size limits which require tricky repartitioning if outgrown. The size cost is also large relative to the ~180 KB bump expected between major OpenWRT kernel releases. No OpenWrt packages have hard dependencies on this; samba4 and mariadb can take advantage if available (+KERNEL_IO_URING:liburing) but otherwise build and work fine. Since CONFIG_IO_URING is already managed via the KERNEL_IO_URING setting in Config-kernel.in (default Y), remove it from those target configs which unconditionally enable it, and update the defaults to enable it conditionally only on more powerful 64-bit x86 and arm devices. It may still be manually enabled as needed for high-performance custom builds. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* kernel: fix handling of CONFIG_DYNAMIC_DEBUGTony Ambardar2023-05-031-1/+0
| | | | | | | | | | Since CONFIG_DYNAMIC_DEBUG is already managed via the KERNEL_DYNAMIC_DEBUG setting in Config-kernel.in (default N), remove or disable it in target configs which unconditionally enable it, along with the related setting CONFIG_DYNAMIC_DEBUG_CORE. This saves several KB in the kernels for ipq40xx, ipq806x, filogic, mt7622, qoriq, and sunxi. Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert AVM FRITZ!Repeater 3000 to DSANick Hainke2023-05-033-2/+22
| | | | | | Convert the repeater to DSA. Signed-off-by: Nick Hainke <vincent@systemli.org>
* kernel: bump 5.15 to 5.15.109John Audia2023-04-301-1/+1
| | | | | | | | | | | | | | | Removed upstreamed: backport-5.15/743-v6.3-0005-net-dsa-b53-mmap-add-phy-ops.patch[1] All other patches automatically rebased. 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.109&id=357fa038d93d0e9159a0f0d45bae0f8654e2ade5 Build system: x86_64 Build-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, ramips/tplink_archer-a6-v3, filogic/xiaomi_redmi-router-ax6000-ubootmod Signed-off-by: John Audia <therealgraysky@proton.me>
* ipq40xx: convert GL-AP1300 to DSANick Hainke2023-04-244-6/+37
| | | | | | | | | | Convert GL-AP1300 to DSA and enable it. While working on it rename the GL-AP1300 leds from green to white. Tested-by: Rob White <rob@blue-wave.net> Tested-by: Robert Sommer <frauhottelmann@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert AP-365 to DSADavid Bauer2023-04-152-2/+2
| | | | | | | | | Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as the board design is pretty much the already updated AP-303. Run-tested on the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* base-files: fix Linksys upgrade, restore config stepMichael Trinidad2023-04-111-1/+1
| | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This corrects a typo in the call of nand_do_upgrade_failed for ipq40xx and ipq806x devices using the linksys.sh script. Fixes: 8634c1080d50 ("ipq40xx: Fix Linksys upgrade, restore config step") Fixes: 2715aff5df83 ("ipq806x: Fix Linksys upgrade, restore config step") Signed-off-by: Michael Trinidad <trinidude4@hotmail.com>
* ipq40xx: add LED functions for Google WiFiJan-Niklas Burfeind2023-03-311-2/+9
| | | | | | | | | | | | | | | | | Add LED function properties for the LED controller to avoid failing driver probe with kernel 5.15. While at it, also define the OpenWrt LED indicator patterns for this device. Ref commit 583ac0e11df7 ("mpc85xx: update lp5521 led-controller node for 5.10") Google uses white for running and red for an issue Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Tested-by: Andrijan Möcker <amo@ct.de> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add reset button for Google WiFi (Gale)Jan-Niklas Burfeind2023-03-311-1/+14
| | | | | | | | | | Add the external reset button for use with OpenWrt. Co-authored-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Jan-Niklas Burfeind <git@aiyionpri.me> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Tested-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Fix Linksys upgrade, restore config stepJeff Kletsky2023-03-261-1/+6
| | | | | | | | | | | | | | | | | | | | It appears that the refactor of the upgrade process for NAND devices resulted in the nand_do_upgrade_success step not being called for devices using the linksys.sh script. As a result, configuration was not preserved over sysupgrade steps. This was restored for some devices in commit 84ff6c90dda1 ("base-files: bring back nand_do_upgrade_success"). This restored preservation of config for ipq40xx devices using the linksys.sh script. Other devices and targets have not been examined. Closes: #11677 Fixes: e25e6d8e54 ("base-files: fix and clean up nand sysupgrade code") Tested-on: EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> (checkpatch nitpick) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-215-1/+441
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* ipq40xx: mf18a: rename wifi0 calibration variant to ZTE-MF18AChristian Marangi2023-03-181-1/+1
| | | | | | | Rename wifi0 calibration variant to ZTE-MF18A to allign to BDF changes for ZTE MF18A. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: rutx10: Add missing variant to ath10k wifiChristian Marangi2023-03-181-0/+10
| | | | | | | Add missing variant to ath10k wifi to allign to BDF changes for Teltonika RUTX10. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: mf18a: Add missing variant to PCI ath10k cardChristian Marangi2023-03-181-0/+1
| | | | | | | Add missing variant to PCI ath10k card to allign to BDF changes for ZTE MF18A. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: update Crisis Innovation Lab MeshPoint.One BDFMantas Pucka2023-03-171-1/+1
| | | | | | | | | | Make sure it uses updated Jalapeno BDF inherited from Device/8dev_jalapeno-common Fixes: 146eb4925c7f ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One") Signed-off-by: Mantas Pucka <mantas@8devices.com> [ fix Fixes tag to correct format and fix commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: set specific BDF file for 8devices Habanero/JalapenoMantas Pucka2023-03-171-0/+2
| | | | | | | | | Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx generic.mk Signed-off-by: Mantas Pucka <mantas@8devices.com> [ split ipq40xx changes in separate commit ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: convert Netgear EX6100/EX6150 v2 to DSADavid Bauer2023-03-083-5/+19
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: Linksys MR8300: fix the USB port powerDaniel González Cabanelas2023-02-251-1/+11
| | | | | | | | | | | | | The USB port on the MR8300 randomly fails to feed bus-powered devices. This is caused by a misconfigured pinmux. The GPIO68 should be used to enable the USB power (active low), but it's inside the NAND pinmux. This GPIO pin was found in the original firmware at a startup script in both MR8300 and EA8300. Therefore apply the fix for both boards. Signed-off-by: Daniel González Cabanelas <dgcbueu@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: chromium: Enable kmod-ramoops by defaultBrian Norris2023-02-181-1/+5
| | | | | | | | Chromium devices (like Google WiFi) have ramoops memory reserved by the bootloader. Let's enable the ramoops kernel module by default, so we get better crash logging. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* treewide: replace /sys/devices/virtual/ubi by /sys/class/ubiDaniel Golle2023-02-151-1/+1
| | | | | | | | | | Starting from Linux Kernel version 6.3 UBI devices will no longer be considered virtual, but rather have an MTD device parent. Hence they will no longer be listed under /sys/devices/virtual/ubi which is used in multiple places in OpenWrt. Prepare for future kernels by using /sys/class/ubi instead of /sys/devuces/virtual/ubi. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: fix dts whitespaceFelix Baumann2023-02-092-2/+2
| | | | | | Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq4019: fix dts white-spaceFelix Baumann2023-02-088-438/+438
| | | | | | | Replace blanks with tabs Remove whitespace from otherwise empty lines Signed-off-by: Felix Baumann <felix.bau@gmx.de>
* ipq40xx: fix assignment of lan port numbers for Cell C RTL30VWCezary Jackiewicz2023-02-061-2/+2
| | | | | | After switching to DSA, the LAN ports in Cell C RTL30VW have swapped numbers. Assigning the right numbers. Signed-off-by: Cezary Jackiewicz <cezary@eko.one.pl>
* treewide: replace wpad-basic-wolfssl defaultRosen Penev2023-02-041-1/+1
| | | | | | | The newly merged mbedtls backend is smaller and has fewer ABI related issues than the wolfSSL one. Signed-off-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: convert Extreme AP3915i to DSAJames Andrewartha2023-01-173-2/+16
| | | | | | Convert and re-enabled Extreme AP3915i to DSA. Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
* ipq40xx: add DSL support for FritzBox 7530Martin Schiller2023-01-164-6/+34
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up MAC, LED, settings and default packages for DSL usage, similar to the lantiq target. Due to licensing uncertainty, we do not include the firmware files for the DSL drivers. To have a working DSL setup, follow the instructions below. Download the firmware files locally: mkdir -p files/lib/firmware/09a9 wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin For people building their own images: Run the above commands in the root of your local OpenWrt clone, and the firmware files will be part of the resulting images. For people downloading images: Copy the firmware files onto the router once it's booted up: scp -O -r files/lib/firmware root@fritz:/lib Reboot the device afterwards. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [cleaned up] Signed-off-by: Andre Heider <a.heider@gmail.com> [set up LED] Signed-off-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: fritzbox-7530.dts: increase dma coherent pool sizeMartin Schiller2023-01-161-0/+4
| | | | | | | This is needed by the mei driver to be able to download the firmware. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add Intel/Lantiq ATM hacksMartin Schiller2023-01-162-0/+180
| | | | | | | | | | Similar to the lantiq platform, these are required for DSL support. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [switch to kernel 5.10 and 5.15] Signed-off-by: Jan Hoffmann <jan@3e8.eu> [update patches based on UGW 8.5.2.10, remove 5.10 support] Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-155-2/+541
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-144-0/+498
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* kernel: bump 5.15 to 5.15.87John Audia2023-01-131-1/+1
| | | | | | | | | | | | | Removed upstreamed: generic/hack-5.15/290-net-dsa-mv88e6xxx-depend-on-PTP-conditionally.patch[1] Build system: x86_64 Build-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod Run-tested: bcm2711/RPi4B, filogic/xiaomi_redmi-router-ax6000-ubootmod 1. https://git.kernel.org/pub/scm/linux/kernel/git/stable/linux.git/commit/?h=v5.15.87&id=945e58bdaf6faf6e3f957d182244fa830acddab4 Signed-off-by: John Audia <therealgraysky@proton.me>
* Revert "TODROP: test for ipq4019 target"Christian Marangi2023-01-111-1/+1
| | | | | | | | This reverts commit 4eb587f7e0a49b9c404857b18571f45981b3a7fc. Pushed by mistake while merging a pr using script. Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* TODROP: test for ipq4019 targetChristian Marangi2023-01-111-1/+1
| | | | | | COMMIT TO DROP Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* treewide: update NVMEM symbolsRafał Miłecki2023-01-071-1/+1
| | | | | Fixes: 8dfe69cdfc5c ("kernel: update nvmem subsystem to the latest upstream") Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* generic: fix silicon labs spidev bindingsVincent Tremblay2023-01-062-2/+2
| | | | | | | | | | | | | | | Fix Silicon Labs bindings in the spidev driver Some bindings for Silicon Labs chips already exists upstream. These bindings can be found in trivial-devices.yaml. The existing bindings are using "silabs" instead of "siliconlabs" to identify the manufacturer. This commit add two submitted patches for silabs chips and rename the manufacturer in the different DTS for more coherence. Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: fix wlan mac address for Aruba AP-303HBjoern Dobe2023-01-041-4/+6
| | | | | | | | | | | Assigns the correct mac address from nvmen to the wlan interfaces. This Mac address corresponds to the label "Wireless MAC" on the device and the stock firmware. Removes duplicate entry of calibration variant for both radios. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de>
* ipq40xx: delete files used for building 5.10 kernelNick Hainke2023-01-0325-2442/+0
| | | | | | | The kernel 5.15 now defaults. Remove unnecessary files. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: sysupgrade: allow flashing Linksys factory firmwareTony Ambardar2022-12-311-0/+18
| | | | | | | | | | | | | | | | | Allow forced flashing of a factory firmware image, after checking for the correct FIT magic header and Linksys board-specific footer. Details of the footer are already described in scripts/linksys-image.sh. This is convenient as it avoids using a TFTP server or OEM GUI, and allows restoring OEM firmware or installing a "breaking" OpenWrt update (e.g DSA migration and kernel repartition) directly from the command line. Devices supported at this time include EA6350v3, EA8300, MR8300 and WHW01. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> # WHW01 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-313-2/+22
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-314-11/+8
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-314-23/+38
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-293-2/+34
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: fix usb driver not loaded for GL-A1300Weiping Yang2022-12-111-0/+8
| | | | | | | This patch enables USB support for the GL.iNet GL-A1300 Repair the usb driver startup phase is not loaded Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-279-217/+347
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: remove '-fit' string from kernel filenamesDaniel Golle2022-11-241-4/+4
| | | | | | | | The type of those images is already distinguishable by the '.itb' extension, there is no need for an additional '-fit' string in the filenames. Remove it to behave more like other targets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove 'nand-' string from image filenamesDaniel Golle2022-11-242-16/+16
| | | | | | | | | Only on the ipq40xx subtarget different filenames were used for NAND- based devices. This is unneeded, confusing and breaks downstream tools such as luci-app-attendedsysupgrade and auc. Remove the 'nand-' string from image filenames to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: dts: remove leftover nodes after DSA conversionLech Perczak2022-11-133-29/+1
| | | | | | | | | | | | | | Remove ess-psgmii@98000, edma@c080000 and ess-switch@c000000 nodes. These nodes are not used after the DSA conversion, but were left over in a few devices added recently. ZTE MF289F is omitted on purpose, as for it, these nodes will be removed together with DSA conversion. Build tested only, as I only have MF286D from those devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-133-7/+32
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-20 10:07:50 +0000