aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: disable boards not converted to DSADavid Bauer2022-10-023-43/+86
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: remove non-converted network configsRobert Marko2022-10-021-96/+0
| | | | | | | Remove networking configs for non DSA converted boards in ipq40xx. Currently, they are just causing clutter. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: ipqess: enable threaded NAPIRobert Marko2022-10-021-2/+4
| | | | | | | | Enable threaded NAPI by default in IPQESS driver as it significantly improves network perfromance, in my testing about 100+ Mbps in WAN-LAN routing. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: Meraki MR33: convert MAC addresses to nvmemLech Perczak2022-10-023-9/+19
| | | | | | | | This fixes assigning random MAC to br-lan interface upon boot. While at that, rename at24@50 node to eeprom@50, to align with upstream device tree style. Signed-off-by: Lech Perczak <lech.perczak@gmail.com>
* ipq40xx: convert some boards to DSARobert Marko2022-10-0232-99/+754
| | | | | | | | | | | | Convert IPQ40xx boards to DSA setup. Signed-off-by: Leon M. George <leon@georgemail.eu> Signed-off-by: Lech Perczak <lech.perczak@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org> Signed-off-by: ChunAm See <z1250747241@gmail.com> Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Andrew Sim <andrewsimz@gmail.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: qca8k: introduce proper PSGMII calibrationSerhii Serhieiev2022-10-022-12/+331
| | | | | | | | | | | | Serhii and others have experienced PSGMII link degradation up to point that it actually does not pass packets at all or packets arrive as zeros. This usually happened after a couple of hot reboots. Serhii has managed to track it down to PSGMII calibration not being done properly and has fixed it, so all of the code is Serhii-s work. Signed-off-by: Serhii Serhieiev <adron@mstnt.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: qca807x: drop kernel version checksRobert Marko2022-10-021-16/+0
| | | | | | | Since kernel 5.4 has been droppped from IPQ40xx, there is no need to keep the version checks for kernels older than 5.10. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: qca807x: add suspend and resume opsSerhii Serhieiev2022-10-021-0/+4
| | | | | | | | | | Currently, suspend and resume ops are not present, this means that if user disables a DSA interface that the PHY-s remain alive and the link is up. Fix it by using generic PHY suspend and resume ops. Signed-off-by: Serhii Serhieiev <adron@mstnt.com> Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: sxtsq-5-ac: correct TCSR ESS typeRobert Marko2022-10-021-1/+1
| | | | | | | SXTsq 5 ac uses RGMII on the port 5 and not PSGMII, so correct the TCSR interface type property. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: enable ethernet and DSA driver comboRobert Marko2022-10-022-0/+16
| | | | | | | | Select the Ethernet driver, DSA tag driver and the DSA driver itself to be built in the kernel config. They automatically pull in switchdev and phylink. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add DSA switch driverRobert Marko2022-10-0212-1190/+678
| | | | | | | | | | | | | | | | | | | | | | | | | | | | Qualcomm IPQ40xx SoC-s have a variant of QCA8337N switch built-in. It shares most of the stuff with its external counterpart, however it is modified for the SoC. Namely, it doesn't have second CPU port (Port 6), so it has 6 ports instead of 7. It also has no built-in PHY-s but rather requires external PSGMII based companion PHY-s (QCA8072 and QCA8075) for which it first needs to carry out calibration before using them. PSGMII has a SoC built-in PHY that is used to connect to the PHY-s which unfortunately requires some magic values as the datasheet doesnt document the bits that are being set or the register at all. Since its built-in it is MMIO like other peripherals and doesn't have its own MDIO bus but depends on the SoC provided one. CPU connection is at Port 0 and it uses some kind of a internal connection and no traditional RGMII/SGMII. It also doesn't use in-band tagging like other qca8k switches so a shinfo based tagger is used. This is based on the current OpenWrt qca8k version that has been imported from generic target. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: import qca8k from genericRobert Marko2022-10-022-0/+2500
| | | | | | | | This is just importing the qca8k driver from the generic target. It will be used as the based for IPQ40xx version, this is just to be able to see the diff. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add PSGMII PHY mode defineRobert Marko2022-10-022-0/+122
| | | | | | | | | | | PSGMII is a Qualcomm specific mode similar to QSGMII but it has 5 SGMII lines instead of 4 in QSGMII. This just adds the support for the PHY layer to be able to identify the mode for further use. It is required for the DSA driver. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add IPQESS ethernet driverRobert Marko2022-10-029-1/+2296
| | | | | | | | | IPQESS is the EDMA replacement driver for the IPQ40xx SoC built-in ethernet controller. Unlike EDMA it is Phylink based and doesnt touch PHY-s directly. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: qca807x: always set PSGMII AZ WARRobert Marko2022-10-023-12/+7
| | | | | | | | | | | | There is no point in using a DT property to trigger setting the PSGMII PHY AZ transmitting ability. Especially since EEE can be disabled using ethtool anyway. Fixup the mask for setting the workaround as only BIT(0) is actually being changed and use the phy_clear_bits_mmd helper instead of reading, then clearing the bit and writing back as it does everything for us. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add shinfo based DSA tag driverRobert Marko2022-10-024-0/+461
| | | | | | | | | | | | IPQ40xx requires a special DSA tag driver despite using the QCA8337N switch. However they have changed the header format and the existing QCA tag driver cannot be reused. For details on how it actually works and else read the patch commit description. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: disable nodes instead of deleting themRobert Marko2022-10-025-26/+88
| | | | | | | There is no reason to delete the DT PHY nodes as you can just disable them. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: qca807x: add SFP improvementsRobert Marko2022-10-021-66/+74
| | | | | | | | | | | | | | | | | | | Currently, QCA807x doesnt do any kind of validation to see whether it actually supports the inserted module. So lets add checks to allow only 1000BaseX and 100BaseFX based modules. While adding validation, move fiber configuration to insert/remove events instead of always doing it at config time. This allows getting rid of the DT property for fiber enable and now only the upstream sfp phandle is required. Since we are refactoring fiber related code, lets heavily simplify the status polling as the current logic is overcomplicated due to previous wish to support non standard SFP cages that dont have pins properly connected, that is removed now and only proper SFP cages will work. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: drop ESSEDMA + AR40xx DTS nodesRobert Marko2022-10-0259-1096/+0
| | | | | | | In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx DTS nodes. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: drop ESSEDMA + AR40xxRobert Marko2022-10-0221-7480/+1
| | | | | | | | | | In order to start working on IPQESS + DSA drop the old ESSEDMA + AR40xx driver combo. Remove the kernel symbols, disable swconfig and drop swconfig package as they are not needed anymore. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: Add ZTE MF289FGiammarco Marzano2022-09-245-5/+462
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | It's a 4G Cat.20 router used by Vodafone Italy (called Vodafone FWA) and Vodafone DE\T-Mobile PL (called GigaCube). Modem is a MiniPCIe-to-USB based on Snapdragon X24, it supports 4CA aggregation. There are currently two hardware revisions, which differ on the 5Ghz radio: AT1 = QCA9984 5Ghz Radio on PCI-E bus AT2 = IPQ4019 5Ghz Radio inside IPQ4019 like 2.4Ghz Device specification -------------------- SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz: (QCA9984): a/n/ac, 4x4 HW REV AT1 (IPA4019): a/n/ac, 2x2 HW REV AT2 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Network (white or red), Wifi, Power and 1 internal (blue) Power: 12 VDC, 1 A Connector type: Barrel Bootloader: U-Boot Installation ------------ 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial connector GND (which is right next to the thing with MF289F MIMO-V1.0), RX, TX (refer to this image: https://ibb.co/31Gngpr). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. Stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf289f-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock, specially mtd16 (Web UI) and mtd17 (rootFS). Use /tmp as temporary storage and do: WEB PARITION -------------------------------------- cat /dev/mtd16 > /tmp/mtd16.bin scp /tmp/mtd16.bin root@YOURSERVERIP:/ rm /tmp/mtd16.bin ROOT PARITION -------------------------------------- cat /dev/mtd17 > /tmp/mtd17.bin scp /tmp/mtd17.bin root@YOURSERVERIP:/ rm /tmp/mtd17.bin 6. Login via ssh or serial and remove stock partitions (default IP 192.168.0.1): # this can return an error, if ubi was attached before # or rootfs part was erased before. ubiattach -m 17 # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # some devices doesn't have it ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. download and install image via sysupgrade -n (either use wget/scp to copy the mf289f's squashfs-sysupgrade.bin to the device's /tmp directory) sysupgrade -n /tmp/openwrt-...-zte_mf289f-squashfs-sysupgrade.bin Sometimes it could print ubi attach error, but please ignore it if process goes forward. Flash Layout NAND: mtd8: 000a0000 00020000 "fota-flag" mtd9: 00080000 00020000 "0:ART" mtd10: 00080000 00020000 "mac" mtd11: 000c0000 00020000 "reserved2" mtd12: 00400000 00020000 "cfg-param" mtd13: 00400000 00020000 "log" mtd14: 000a0000 00020000 "oops" mtd15: 00500000 00020000 "reserved3" mtd16: 00800000 00020000 "web" mtd17: 01d00000 00020000 "rootfs" mtd18: 01900000 00020000 "data" mtd19: 03200000 00020000 "fota" mtd20: 0041e000 0001f000 "kernel" mtd21: 0101b000 0001f000 "ubi_rootfs" SPI: mtd0: 00040000 00010000 "0:SBL1" mtd1: 00020000 00010000 "0:MIBIB" mtd2: 00060000 00010000 "0:QSEE" mtd3: 00010000 00010000 "0:CDT" mtd4: 00010000 00010000 "0:DDRPARAMS" mtd5: 00010000 00010000 "0:APPSBLENV" mtd6: 000c0000 00010000 "0:APPSBL" mtd7: 00050000 00010000 "0:reserved1" Back to Stock (!!! need original dump taken from initramfs !!!) ------------- 1. Place mtd16.bin and mtd17.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 2. Connect serial console (115200,8n1) to serial console connector (refer to the pin-out from above). 3. Connect TFTP server to RJ-45 port (WAN/LAN1). 4. rename mtd16.bin to web.img and mtd17.bin to root_uImage_s 5. Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase RootFS+Web: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 ${dir}root_uImage_s nand erase 0x1800000 0x1D00000 nand write $fileaddr 0x1800000 $filesize This will restore Web Interface: tftpboot 0x84000000 ${dir}web.img nand erase 0x1000000 0x800000 nand write $fileaddr 0x1000000 $filesize After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router Signed-off-by: Giammarco Marzano <stich86@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com> (Warning: commit message did not conform to UTF-8 - hopefully fixed?, added description of the pin-out if image goes down, reformatted commit message to be hopefully somewhat readable on git-web, redid some of the gpio-buttons & leds DT nodes, etc.) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Sony NCP-HG100/CellularINAGAKI Hiroshi2022-09-248-1/+754
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Sony NCP-HG100/Cellular is a IoT Gateway with 2.4/5 GHz band 11ac (WiFi-5) wireless function, based on IPQ4019. Specification: - SoC : Qualcomm IPQ4019 - RAM : DDR3 512 MiB (H5TC4G63EFR) - Flash : eMMC 4 GiB (THGBMNG5D1LBAIT) - WLAN : 2.4/5 GHz 2T2R (IPQ4019) - Ethernet : 10/100/1000 Mbps x2 - Transceiver : Qualcomm QCA8072 - WWAN : Telit LN940A9 - Z-Wave : Silicon Labs ZM5101 - Bluetooth : Qualcomm CSR8811 - Audio DAC : Realtek ALC5629 - Audio Amp. : Realtek ALC1304 - Voice Input Processor : Conexant CX20924 - Micro Controller Unit : Nuvoton MINI54FDE - RGB LED, Fan, Temp. sensors - Touch Sensor : Cypress CY8C4014LQI - RGB LED driver : TI LP55231 (2x) - LEDs/Keys : 11x, 6x - UART : through-hole on PCB - J1: 3.3V, TX, RX, GND from tri-angle marking - 115200n8 - Power : 12 VDC, 2.5 A Flash instruction using initramfs image: 1. Prepare TFTP server with the IP address 192.168.132.100 and place the initramfs image to TFTP directory with the name "C0A88401.img" 2. Boot NCP-HG100/Cellular and interrupt after the message "Hit any key to stop autoboot: 2" 3. Perform the following commands and set bootcmd to allow booting from eMMC setenv bootcmd "mmc read 0x84000000 0x2e22 0x4000 && bootm 0x84000000" saveenv 4. Perform the following command to load/boot the OpenWrt initramfs image tftpboot && bootm 5. On the initramfs image, perform sysupgrade with the sysupgrade image (if needed, backup eMMC partitions by dd command and download to other place before performing sysupgrade) 6. Wait for ~120 seconds to complete flashing Known issues: - There are no drivers for audio-related chips/functions in Linux Kernel and OpenWrt, they cannot be used. - There is no driver for MINI54FDE Micro-Controller Unit, customized for this device by the firmware in the MCU. This chip controls the following functions, but they cannot be controlled in OpenWrt. - RGB LED - Fan this fan is controlled automatically by MCU by default, without driver - Thermal Sensors (2x) - Currently, there is no driver or tool for CY8C4014LQI and cannot be controlled. It cannot be exited from "booting mode" and moved to "normal op mode" after booting. And also, the 4x buttons (mic mute, vol down, vol up, alexa trigger) connected to the IC cannot be controlled. - it can be exited from "booting mode" by installing and executing i2cset command: opkg update opkg install i2c-tools i2cset -y 1 0x14 0xf 1 - There is a connection issue on the control by uqmi for the WWAN module. But modemmanager can be used without any issues and the use of it is recommended. - With the F2FS format, too many errors are reported on erasing eMMC partition "rootfs_data" while booting: [ 1.360270] sdhci: Secure Digital Host Controller Interface driver [ 1.363636] sdhci: Copyright(c) Pierre Ossman [ 1.369730] sdhci-pltfm: SDHCI platform and OF driver helper [ 1.374729] sdhci_msm 7824900.sdhci: Got CD GPIO ... [ 1.413552] mmc0: SDHCI controller on 7824900.sdhci [7824900.sdhci] using ADMA 64-bit [ 1.528325] mmc0: new HS200 MMC card at address 0001 [ 1.530627] mmcblk0: mmc0:0001 004GA0 3.69 GiB [ 1.533530] mmcblk0boot0: mmc0:0001 004GA0 partition 1 2.00 MiB [ 1.537831] mmcblk0boot1: mmc0:0001 004GA0 partition 2 2.00 MiB [ 1.542918] mmcblk0rpmb: mmc0:0001 004GA0 partition 3 512 KiB, chardev (247:0) [ 1.550323] Alternate GPT is invalid, using primary GPT. [ 1.561669] mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11 p12 p13 p14 p15 p16 p17 ... [ 8.841400] mount_root: loading kmods from internal overlay [ 8.860241] kmodloader: loading kernel modules from //etc/modules-boot.d/* [ 8.863746] kmodloader: done loading kernel modules from //etc/modules-boot.d/* [ 9.240465] block: attempting to load /etc/config/fstab [ 9.246722] block: unable to load configuration (fstab: Entry not found) [ 9.246863] block: no usable configuration [ 9.254883] mount_root: overlay filesystem in /dev/mmcblk0p17 has not been formatted yet [ 9.438915] urandom_read: 5 callbacks suppressed [ 9.438924] random: mkfs.f2fs: uninitialized urandom read (16 bytes read) [ 12.243332] mmc_erase: erase error -110, status 0x800 [ 12.246638] mmc0: cache flush error -110 [ 15.134585] mmc_erase: erase error -110, status 0x800 [ 15.135891] mmc_erase: group start error -110, status 0x0 [ 15.139850] mmc_erase: group start error -110, status 0x0 ...(too many the same errors)... [ 17.350811] mmc_erase: group start error -110, status 0x0 [ 17.356197] mmc_erase: group start error -110, status 0x0 [ 17.439498] sdhci_msm 7824900.sdhci: Card stuck in wrong state! card_busy_detect status: 0xe00 [ 17.446910] mmc0: tuning execution failed: -5 [ 17.447111] mmc0: cache flush error -110 [ 18.012440] F2FS-fs (mmcblk0p17): Found nat_bits in checkpoint [ 18.062652] F2FS-fs (mmcblk0p17): Mounted with checkpoint version = 428fa16b [ 18.198691] block: attempting to load /etc/config/fstab [ 18.198972] block: unable to load configuration (fstab: Entry not found) [ 18.203029] block: no usable configuration [ 18.211371] mount_root: overlay filesystem has not been fully initialized yet [ 18.214487] mount_root: switching to f2fs overlay So, this support uses ext4 format instead which has no errors. Note: - The primary uart is shared for debug console and Z-Wave chip. The function is switched by GPIO15 (Linux: 427). value: 1: debug console 0: Z-Wave - NCP-HG100/Cellular has 2x os-image pairs in eMMC. - 0:HLOS, rootfs - 0:HLOS_1, rootfs_1 In OpenWrt, the first image pair is used. - "bootipq" command in U-Boot requires authentication with signed-image by default. To boot unsigned image of OpenWrt, use "mmc read" and "bootm" command instead. - This support is for "Cellular" variant of NCP-HG100 and not tested on "WLAN" (non-cellular) variant. - The board files of ipq-wifi may also be used in "WLAN" variant of NCP-HG100, but unconfirmed and add files as for "Cellular" variant. - "NET" LED is used to indicate WWAN status in stock firmware. - There is no MAC address information in the label on the case, use the address included in UUID in the label as "label-MAC" instead. - The "CLOUD" LEDs are partially used for indication of system status in stock firmware, use they as status LEDs in OpenWrt instead of RGB LED connected to the MCU. MAC addresses: LAN : 5C:FF:35:**:**:ED (ART, 0x6 (hex)) WAN : 5C:FF:35:**:**:EF (ART, 0x0 (hex)) 2.4 GHz: 5C:FF:35:**:**:ED (ART, 0x1006 (hex)) 5 GHz : 5C:FF:35:**:**:EE (ART, 0x5006 (hex)) partition layout in eMMC (by fdisk, GPT): Disk /dev/mmcblk0: 7733248 sectors, 3776M Logical sector size: 512 Disk identifier (GUID): **** Partition table holds up to 20 entries First usable sector is 34, last usable sector is 7634910 Number Start (sector) End (sector) Size Name 1 34 1057 512K 0:SBL1 2 1058 2081 512K 0:BOOTCONFIG 3 2082 3105 512K 0:QSEE 4 3106 4129 512K 0:QSEE_1 5 4130 4641 256K 0:CDT 6 4642 5153 256K 0:CDT_1 7 5154 6177 512K 0:BOOTCONFIG1 8 6178 6689 256K 0:APPSBLENV 9 6690 8737 1024K 0:APPSBL 10 8738 10785 1024K 0:APPSBL_1 11 10786 11297 256K 0:ART 12 11298 11809 256K 0:HSEE 13 11810 28193 8192K 0:HLOS 14 28194 44577 8192K 0:HLOS_1 15 44578 306721 128M rootfs 16 306722 568865 128M rootfs_1 17 568866 3958065 1654M rootfs_data [initial work] Signed-off-by: Iwao Yuki <dev.clef@gmail.com> Co-developed-by: Iwao Yuki <dev.clef@gmail.com> [adjustments, cleanups, commit message, sending patch] Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com> (dropped clk_unused_ignore, dropped 901-* patches, renamed key nodes, changed LEDs chan/labels to match func-en, made :net -> (w)wan leds) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: base-files: properly close caseTomasz Maciej Nowak2022-09-241-0/+1
| | | | | | | | Fix this occurrence during boot: /bin/board_detect: line 10: Unsupported: not found Fixes: 80baffd2aa91 (" ipq40xx: add support for Pakedge WR-1") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: luma_wrtq-329acn: differentiate ethernet mac addressesTomasz Maciej Nowak2022-09-241-0/+12
| | | | | | | | On OEM firmware both addresses for In and Out ports are different. Set them as such also in OpenWrt. Fixes: e24635710c7e (" ipq40xx: add support for Luma Home WRTQ-329ACN") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: fix RUTX10 Wi-Fi woesKasparas Elzbutas2022-09-242-30/+8
| | | | | | | | | | | | | This partially reverts: commit cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") U-Boot on these devices mangles the device tree, so nvmem-cell type calibration doesn't work. Fixes: cfc13c44595d ("ipq40xx: utilize nvmem-cells for macs & (pre-)calibration data") Signed-off-by: Kasparas Elzbutas <elzkas@gmail.com> (added reference to commit, rewrote commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix power LED colour ID in Netgear WAC510 dtsAndrew Sim2022-09-191-1/+1
| | | | | | | led_power_green color ID in dts is mistakenly set to amber so correct it by setting it to green Signed-off-by: Andrew Sim <andrewsimz@gmail.com>
* ipq40xx: disable devices with 3MiB kernel sizeSungbo Eo2022-09-181-0/+3
| | | | | | | | | The image builds for Linksys EA6350 v3, EA8300, and MR8300 currently fail on buildbots due to the KERNEL_SIZE, as stated in commit 17b7756b5a20 ("ipq40xx: 5.15: add testing kernel version"). Disable these boards for now. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: add GL-AP1300 label-mac-deviceDavid Bauer2022-09-111-0/+1
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add WAN LED mapping for GL-AP1300David Bauer2022-09-111-0/+3
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: cellc_rtl30vw: fix imagebuilder generationGregory Detal2022-09-111-4/+5
| | | | | | | | | | | | | | | | | The image build process was modifying the generated IMAGE_KERNEL to append rootfs information (crc). This caused: - sysupgrade & factory images to contain 2 times the root.squashfs information due to both modifying the same IMAGE_KERNEL. - the generated imagebuilder to contain an erroneous IMAGE_KERNEL that contained references to an unexisting root.squashfs (the one from previous cause). The RTL30VW wasn't therefore able to boot the generated images as they contained checksums from non existing rootfs. This commit makes sure to use a temporary IMAGE_KERNEL to append the rootfs information for both factory and sysupgrade images. Fixes: #10511 Signed-off-by: Gregory Detal <gregory.detal@tessares.net>
* kernel: bump 5.10 to 5.10.141John Audia2022-09-111-2/+2
| | | | | | All patches automatically rebased. Signed-off-by: John Audia <therealgraysky@proton.me>
* ipq40xx: add LTE packages for GL-AP1300David Bauer2022-09-091-1/+1
| | | | | | | Add LTE packages required for operating the LTE modem optionally shipped with the GL-AP1300. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: switch to 5.15 as default kernelNick Hainke2022-09-091-2/+1
| | | | | | | | | | | | The testing kernel received now multiple months of testing. Set 5.15 as default to give it a test with a broader audience. Tested on: - MikroTik SXTsq 5 AC - FritzBox 4040/7530 - ZyXEL NBG6617 Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq-wifi: add Pakedge WR-1 supportTomasz Maciej Nowak2022-09-072-0/+5
| | | | | | | | | | Calibration variants: Pakedge-WR-1 ETSI, FCC and IC-2.4GHz Pakedge-WR-1-ACMA ACMA Pakedge-WR-1-IC IC-5GHz Pakedge-WR-1-SRRC SRRC Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add support for Pakedge WR-1Tomasz Maciej Nowak2022-09-074-0/+291
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Pakedge WR-1 is a dual-band wireless router. Specification SoC: Qualcomm Atheros IPQ4018 RAM: 256 MB DDR3 Flash: 32 MB SPI NOR WIFI: 2.4 GHz 2T2R integrated 5 GHz 2T2R integrated Ethernet: 5x 10/100/1000 Mbps QCA8075 USB: 1x 2.0 LEDS: 8x (3 GPIO controlled, 5 connected to switch) Buttons: 1x GPIO controlled UART: pin header J5 1. 3.3V, 2. GND, 3. TX, 4. RX baud: 115200, parity: none, flow control: none Installation 1. Rename initramfs image to: openwrt-ipq806x-qcom-ipq40xx-ap.dk01.1-c1-fit-uImage-initramfs.itb and copy it to USB flash drive with FAT32 file system. 2. Connect USB flash drive to the router and apply power while pressing reset button. Hold the button, on the lates bootloader version, when Power and WiFi-5 LEDs will start blinking release it. For the older bootloader holding it for 15 seconds should suffice. 3. Now the router boots the initramfs image, at some point (close to one minute) the Power LED will start blinking, when stops, router is fully booted. 4. Connect to one of LAN ports and use SSH to open the shell at 192.168.1.1. 5. ATTENTION! now backup the mtd8 and mtd9 partitions, it's necessary if, at some point, You want to go back to original firmware. The firmware provided by manufacturer on its site is encrypted and U-Boot accepts only decrypted factory images, so there's no way to restore original firmware. 6. If the backup is prepared, transfer the sysupgrade image to the router and use 'sysupgrade' command to flash it. 7. After successful flashing router will reboot. At some point the Power LED will start blinking, wait till it stops, then router is ready for configuration. Additional information U-Boot command line is password protected. Password is unknown. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add support for Extreme Networks WS-AP3915iDavid Bauer2022-09-065-0/+296
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- Qualcomm IPQ4029 WiSoC 2T2R 802.11 abgn 2T2R 802.11 nac Macronix MX25L25635E SPI-NOR (32M) 512M DDR3 RAM 1x Gigabit LAN 1x Cisco RJ-45 Console port Settings: 115200 8N1 Installation ------------ 1. Attach to the Console port. Power up the device and press the s key to interrupt autoboot. 2. The default username / password to the bootloader is admin / new2day 3. Update the bootcommand to allow loading OpenWrt. $ setenv ramboot_openwrt "setenv serverip 192.168.1.66; setenv ipaddr 192.168.1.1; tftpboot 0x86000000 openwrt-3915.bin; bootm" $ setenv boot_openwrt "sf probe; sf read 0x88000000 0x280000 0xc00000; bootm 0x88000000" $ setenv bootcmd "run boot_openwrt" $ saveenv 4. Download the OpenWrt initramfs image. Serve it using a TFTP server as "openwrt-3915.bin" at 192.1681.66. 5. Download & boot the OpenWrt initramfs image on the access point. $ run ramboot_openwrt 6. Wait for OpenWrt to start. 7. Download and transfer the sysupgrade image to the device using e.g. SCP. 8. Install OpenWrt to the device using "sysupgrade" $ sysupgrade -n /path/to/openwrt.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: point to externally compiled dtbs in recipesTomasz Maciej Nowak2022-09-064-194/+11
| | | | | | | | | | | | | | | | Adjusting dts will cause a rebuild of whole kernel as the buildroot considers this a part of kernel source. It's a royal PITA when trying to prepare support for new device, since this takes a lot of time on slower systems. As it stands, buildroot itself, with own rule, also compiles dtbs and the results are $(KDIR)/image-$(DEVICE_DTS).dtb. With setting DEVICE_DTS_DIR to directory holding the device dts (similarly to some other targets), buildroot doesn't consider changed dts as part of kernel source and rebuilds only dtb. This really speeds up development. And since the kernel built dts are no longer used, drop the paches adding dtses to its build. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* kernel: bump 5.15 to 5.15.64John Audia2022-09-021-2/+2
| | | | | | | | | | All patches automatically rebased Build system: x86_64 Build-tested: bcm2711/RPi4B, mt7622/RT3200 Run-tested: bcm2711/RPi4B, mt7622/RT3200 Signed-off-by: John Audia <therealgraysky@proton.me>
* kernel: bump 5.15 to 5.15.62Petr Štetiar2022-08-232-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Deleted following upstreamed patches: bcm27xx: 950-0006-drm-vc4-hdmi-Fix-HPD-GPIO-detection.patch bcm27xx: 950-0420-drm-vc4-Adopt-the-dma-configuration-from-the-HVS-or-.patch bcm27xx: 950-0425-drm-vc4-A-present-but-empty-dmas-disables-audio.patch bcm27xx: 950-0432-vc4-drm-Avoid-full-hdmi-audio-fifo-writes.patch bcm27xx: 950-0433-vc4-drm-vc4_plane-Remove-subpixel-positioning-check.patch bcm27xx: 950-0435-drm-vc4-Correct-pixel-order-for-DSI0.patch bcm27xx: 950-0436-drm-vc4-Register-dsi0-as-the-correct-vc4-encoder-typ.patch bcm27xx: 950-0437-drm-vc4-Fix-dsi0-interrupt-support.patch bcm27xx: 950-0438-drm-vc4-Add-correct-stop-condition-to-vc4_dsi_encode.patch bcm27xx: 950-0443-drm-vc4-Fix-timings-for-interlaced-modes.patch bcm27xx: 950-0445-drm-vc4-Fix-margin-calculations-for-the-right-bottom.patch bcm27xx: 950-0475-drm-vc4-Reset-HDMI-MISC_CONTROL-register.patch bcm27xx: 950-0476-drm-vc4-Release-workaround-buffer-and-DMA-in-error-p.patch bcm27xx: 950-0477-drm-vc4-Correct-DSI-divider-calculations.patch bcm27xx: 950-0664-drm-vc4-dsi-Correct-max-divider-to-255-not-7.patch bcm53xx: 072-next-ARM_dts_BCM53015-add-mr26.patch mediatek: 920-linux-next-dts-mt7622-bpi-r64-fix-wps-button.patch Manually rebased following patches: bcm27xx: 950-0004-drm-vc4-hdmi-Remove-the-DDC-probing-for-status-detec.patch bcm27xx: 950-0700-net-phy-lan87xx-Decrease-phy-polling-rate.patch bcm27xx: 950-0711-drm-vc4-Rename-bridge-to-out_bridge.patch bcm27xx: 950-0713-drm-vc4-Remove-splitting-the-bridge-chain-from-the-d.patch bcm27xx: 950-0715-drm-vc4-Convert-vc4_dsi-to-using-a-bridge-instead-of.patch bcm27xx: 950-0787-vc4-drm-vc4_plane-Keep-fractional-source-coords-insi.patch bcm27xx: 950-0914-mmc-block-Don-t-do-single-sector-reads-during-recove.patch Runtime tested on turris-omnia and glinet-b1300. Tested-by: John Audia <therealgraysky@proton.me> [bcm2711/RPi4B, mt7622/RT3200] Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: bump 5.10 to 5.10.137Petr Štetiar2022-08-232-2/+2
| | | | | | | | | | Removed following upstreamed patch: * bcm53xx: 081-next-ARM_dts_BCM53015-add-mr26.patch All other patches automagically rebased. Signed-off-by: Petr Štetiar <ynezz@true.cz>
* kernel: Activate CONFIG_GPIOLIB in generic configurationHauke Mehrtens2022-08-102-2/+0
| | | | | | | | All targets expect the malta target already activate the CONFIG_GPIOLIB option. Move it to generic kernel configuration and also activate it for malta. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add MikroTik wAP ac (RBwAPG-5HacD2HnD) supportMark Mentovai2022-07-188-8/+250
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The MikroTik wAP ac (RBwAPG-5HacD2HnD) is a dual-band dual-radio 802.11ac wireless access point with integrated antenna and two Ethernet ports in a weatherproof enclosure. See https://mikrotik.com/product/wap_ac for more information. Important: this is the new ipq40xx-based wAP ac, not the older ath79-based wAP ac (RBwAPG-5HacT2HnD), already supported in OpenWrt. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless - 2.4GHz: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae - 5GHz: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075), 2x 1000/100/10Mb/s ports, one with 802.3af/at PoE in Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Notes: This preserves the MAC addresses of the physical Ethernet ports: - eth0 corresponds to the physical port labeled ETH1 and has the base MAC address. This port can be used to power the device. - eth1 corresponds to the physical port labeled ETH2 and has a MAC address one greater than the base. MAC addresses are set from /lib/preinit/05_set_iface_mac_ipq40xx.sh rather than /etc/board.d/02_network so that they are in effect for preinit. This should likely be done for other MikroTik devices and possibly other non-MikroTik devices as well. As this device has 2 physical ports, they are each connected to their respective PHYs, allowing the link status to be visible to software. Since they are not marked on the case with any role (such as LAN or WAN), both are bridged to the lan network by default, although this can easily be changed if needed. Signed-off-by: Mark Mentovai <mark@mentovai.com>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2022-07-151-1/+1
| | | | | | | | | | The BDFs for the: GL.iNet GL-B2200 were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: R619AC: replace space with - separator in variant stringChristian Lamparter2022-07-151-2/+2
| | | | | | | | | | | | | Kalle: "I see that variant has a space in it, does that work it correctly? My original idea was that spaces would not be allowed, but didn't realise to add a check for that." Is this an easy change? Because the original author (Tim Davis) noted: "You may substitute the & and space with something else saner if they prove to be problematic." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: mikrotik: make RouterBoot partition writeableThibaut VARÈNE2022-06-295-5/+0
| | | | | | | | | Linux MTD requires the parent partition be writable for a child partition to be allowed write permission. In order for soft_config to be writeable (and modifiable via sysfs), the parent RouterBoot partition must be writeable Signed-off-by: Thibaut VARÈNE <hacks@slashdirt.org>
* generic: enable CRYPTO_LIB_BLAKE2S[_X86|_ARM]Tomasz Maciej Nowak2022-06-242-0/+4
| | | | | | | | | | | | This is now built-in, enable so it won't propagate on target configs. Link: https://lkml.org/lkml/2022/1/3/168 Fixes: 79e7a2552e89 ("kernel: bump 5.15 to 5.15.44") Fixes: 0ca93670693b ("kernel: bump 5.10 to 5.10.119") Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com> (Link to Kernel's commit taht made it built-in, CRYPTO_LIB_BLAKE2S[_ARM|_X86] as it's selectable, 5.10 backport) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Meraki MR74Matthew Hagan2022-06-1911-409/+452
| | | | | | | | | | | | The Meraki MR74 is part of the "Insect" series. This device is essentially an outdoor variant of the MR33 with identical hardware, but requiring a config@3 DTS option to be set to allow booting with the stock u-boot. The install procedure is replicated from the MR33, with the exception being that the MR74 sysupgrade image must be used. Signed-off-by: Matthew Hagan <mnhagan88@gmail.com>
* kernel: move Toshiba-TC58NVG0S3H patch to ipq40xx reduxChristian Lamparter2022-06-192-0/+58
| | | | | | | | | | | | | | | | | | Linux' upstream MTD-Maintainer Miquèl Raynal noted: |Reverting seems the safest option here, not knowing how many devices |have these damaged/counterfeit chips. If it is just a couple and only on |Fritzboxes, as suggested in the Github issue this patch could be |carried through OpenWrt and that would seem more future proof IMHO. This patch follows up with the first patch. It actually moves the patches out of target/linux/generic/pending into the ipq40xx's patch heap and adds a little note what happend. For more information, discussions or reports about bad TC58NVG0S3Hs, please visit the OpenWrt's Github Issue #9962: <https://github.com/openwrt/openwrt/issues/9962> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 5.15 to 5.15.45Rui Salvaterra2022-06-061-1/+1
| | | | | | Patches automatically rebased. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* kernel: bump 5.10 to 5.10.120John Audia2022-06-061-1/+1
| | | | | | | | | All patches automatically rebased. Build system: x86_64 Build-tested: ipq806x/R7800, x86/64 Signed-off-by: John Audia <therealgraysky@proton.me>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-06 07:24:49 +0000