aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* kernel: move two symbols to the generic kconfigsRui Salvaterra2021-08-291-2/+0
| | | | | | | CONFIG_RCU_{NEED_SEGCBLIST,STALL_COMMON} are set basically everywhere. Move them to the generic kconfigs. And resort the generic kconfigs while at it. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq40xx: fix Edgecore ECW5211 bootStijn Tintel2021-08-181-0/+1
| | | | | | | The bootloader will look for a configuration section named ap.dk01.1-c2 in the FIT image. If this doesn't exist, the device won't boot. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq40xx: ar40xx: reset port status registerDavid Bauer2021-08-141-2/+1
| | | | | | | This resolves incosnsitencies of the configured RX / TX flow control modes between different boards or bootloaders. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: ar40xx: use FIELD_GET macroDavid Bauer2021-08-141-7/+8
| | | | | | This improves code readability. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: increase EX6150v2 SPI frequencyDavid Bauer2021-08-141-1/+1
| | | | | | | | | The chip supports clock speeds up to 50 MHz, however it won't even read the chip-id correctly at this frequency. 45 MHz however works reliable. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: backport support for nvmem on non platform devicesAnsuel Smith2021-08-051-5/+1
| | | | | | | | | | | | In the current state, nvmem cells are only detected on platform device. To quickly fix the problem, we register the affected problematic driver with the of_platform but that is more an hack than a real solution. Backport from net-next the required patch so that nvmem can work also with non-platform devices and rework our current patch. Drop the mediatek and dsa workaround and rework the ath10k patches. Rework every driver that use the of_get_mac_address api. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq40xx: convert mtd-mac-address to nvmem implementationAnsuel Smith2021-07-192-4/+32
| | | | | | | Define nvmem-cells and convert mtd-mac-address to nvmem implementation. The conversion is done with an automated script. Signed-off-by: Ansuel Smith <ansuelsmth@gmail.com>
* ipq40xx: fix FRITZRepeater 1200 RGMII delayDavid Bauer2021-07-171-1/+1
| | | | | | | | | | | | | | When the AVM FRITZ!Repeater 1200 was introduced on Kernel 4.19, the at803x PHY driver incorrectly set up the delays, not disabling delays set by the bootloader. The PHY was always operating with RX as well as TX delays enabled, but with kernel 5.4 and later, the required TX delay is disabled, breaking ethernet operation. Correct the PHY mode, so the driver enables both delays. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: increase SPI frequency for Zyxel NBG6617Dmitry Tunin2021-07-111-3/+3
| | | | | | | | | | | | The mx25l25635f supports clock speed up to 50Mhz. Also remove obsolete "mx25l25635f" hack and rename the matching device-tree flash node. Signed-off-by: Dmitry Tunin <hanipouspilot@gmail.com> [mention node rename as well. chip is very very likely always the "f" revision for all NBG6617] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* treewide: call check-size before append-metadataAdrian Schmutzler2021-07-102-5/+5
| | | | | | | | | | sysupgrade metadata is not flashed to the device, so check-size should be called _before_ adding metadata to the image. While at it, do some obvious wrapping improvements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ipq40xx: add missing case closing symbolAdrian Schmutzler2021-06-281-0/+1
| | | | | | | Though not strictly necessary, add the closing symbol to make the job easier for future developers editing this file. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: specify FritzBox 7530 LAN port label numbersRafał Miłecki2021-06-241-1/+1
| | | | | | | | | This helps managing LAN ports. Ref: https://forum.openwrt.org/t/openwrt-21-02-0-second-release-candidate/98026/121 Fixes: 95b0c07a618f ("ipq40xx: add support for FritzBox 7530") Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
* ipq40xx: add uboot-envtools to default packagesTomasz Maciej Nowak2021-06-062-17/+14
| | | | | | | | | | | | | | | | | | | When support for Luma WRTQ-329ACN was added, the instructions for flashing this device include using tools from uboot-envtools package. Unfortunately the OpenWrt buildroot system omits packages from DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE, CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In result the official images are without tools mentioned in the instruction. The workoround for the fashing would be installing uboot-envtools when booted with initramfs image, but not always the access to internet is available. The other method would be to issue the necesary command in U-Boot environment but some serial terminals default configuration don't work well with pasting lines longer than 80 chars. Therefore add uboot-envtools to default packages, which adds really small flash footprint to rootfs, where increased size usually is not an issue. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* treewide: remove "+" sign for increment with macaddr_addAdrian Schmutzler2021-06-052-16/+16
| | | | | | | | | | | | Many people appear to use an unneeded "+" prefix for the increment when calculating a MAC address with macaddr_add. Since this is not required and used inconsistently [*], just remove it. [*] As a funny side-fact, copy-pasting has led to almost all hotplug.d files using the "+", while nearly all of the 02_network files are not using it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-057-1/+411
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix hard_config partition size on MikroTik hAP-ac2Baptiste Jonglez2021-05-081-0/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The routerbootparts driver dynamically discovers the location of MikroTik partitions, but it cannot determine their size (except by extending them up to the start of the next discovered partition). The hard_config partition has a default size of 0x1000 in the driver, while it actually takes 0x2000 on the hAP-ac2. Set the correct size in the hAP-ac2 DTS. On most devices, this isn't a problem as the actual data fits in 0x1000 bytes. However, some devices have larger data that doesn't fit in 0x1000 bytes. In any case, all devices seen so far have enough space for a 0x2000 hard_config partition before the start of the dtb_config partition. With the current 0x1000 size: 0x00000000e000-0x00000000f000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" With this patch extending the size to 0x2000: 0x00000000e000-0x000000010000 : "hard_config" 0x000000010000-0x000000017bbc : "dtb_config" Other ipq40xx boards may need the same fix but it needs testing. References: https://forum.openwrt.org/t/support-for-mikrotik-hap-ac2/23333/324 Acked-by: Thibaut VARÈNE <hacks@slashdirt.org> Signed-off-by: Baptiste Jonglez <git@bitsofnetworks.org>
* kernel: bump 5.4 to 5.4.114John Audia2021-04-301-3/+3
| | | | | | | | | | | | | | | | | | | | | | | | | | Manually rebased* generic/backport-5.4/700-v5.5-net-core-allow-fast-GRO-for-skbs-with-Ethernet-heade.patch Added new backport* generic/backport-5.4/050-gro-fix-napi_gro_frags-Fast-GRO-breakage-due-to-IP-a.patch All others updated automatically. The new backport was included based on this[1] upstream commit that will be mainlined soon. This change is needed because Eric Dumazet's check for NET_IP_ALIGN (landed in 5.4.114) causes huge slowdowns on drivers which use napi_gro_frags(). Build system: x86_64 Build-tested: ipq806x/R7800 Run-tested: ipq806x/R7800 No dmesg regressions, everything functional *Credit to Alexander Lobakin 1. https://git.kernel.org/pub/scm/linux/kernel/git/netdev/net.git/commit/?id=7ad18ff6449cbd6beb26b53128ddf56d2685aa93 Signed-off-by: John Audia <graysky@archlinux.us>
* ipq40xx: add support for MikroTik SXTsq 5 acRoger Pueyo Centelles2021-04-297-3/+269
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | This commit adds support for the MikroTik SXTsq 5 ac (RBSXTsqG-5acD), an outdoor 802.11ac wireless CPE with one 10/100/1000 Mbps Ethernet port. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 16 dBi antennae - Ethernet: IPQ4018 (SoC) 1x 10/100/1000 port, 10-28 Vdc PoE in - 1x Ethernet LED (green) - 7x user-controllable LEDs · 1x power (blue) · 1x user (green) · 5x rssi (green) Note: Serial UART is probably available on the board, but it has not been tested. Flashing: Boot via TFTP the initramfs image. Then, upload a sysupgrade image via SSH and flash it normally. More info at the "Common procedures for MikroTik products" page https://openwrt.org/toh/mikrotik/common. Signed-off-by: Roger Pueyo Centelles <roger.pueyo@guifi.net>
* treewide: switch the timer frequency to 100 HzRui Salvaterra2021-04-211-2/+0
| | | | | | | | Some targets select HZ=100, others HZ=250. There's no reason to select a higher timer frequency (and 100 Hz are available in every architecture), so change all targets to 100 Hz. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* treewide: remove redundant ubifs kconfig symbolsRui Salvaterra2021-04-211-4/+0
| | | | | | | For the targets which enable ubifs, these symbols are already part of the generic kconfigs. Drop them from the target kconfigs. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq40xx: add MikroTik hAP ac2 supportRobert Marko2021-04-056-1/+314
| | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD52G-5HacD2HnD-TC (hAP ac²), a indoor dual band, dual-radio 802.11ac wireless AP with integrated omnidirectional antennae, USB port and five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac2 for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - RAM: 128 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 2.5 dBi antennae · Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 2.5 dBi antennae - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 5x 1000/100/10 port, passive PoE in - 1x USB Type A port Installation: Boot the initramfs image via TFTP and then flash the sysupgrade image using "sysupgrade -n" Signed-off-by: Robert Marko <robimarko@gmail.com>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2021-03-191-1/+0
| | | | | | Move some disabled symbols found in armvirt target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ipq40xx: work-around borked QCA SDK bootloaderDaniel Golle2021-03-061-0/+1
| | | | | | | | | | | | | | | The bootloader of many ipq40xx boards seems to require the config node of the FIT image to be 'config@1' (or a secific different value). This requirement used to be implicitely satisfied because OpenWrt used to also call the configuration node inside a FIT image 'config@1'. However, as recent U-Boot now prohibits the use of the '@' symbol as part of node names, this was changed by commit 5ec60cbe9d ("scripts: mkits.sh: replace @ with - in nodes") Explicitely restore the default name of the configuration node to 'config@1' on ipq40xx. Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* treewide: remove execute bit and shebang from board.d filesAdrian Schmutzler2021-03-063-3/+0
| | | | | | | | | | | | | | | | So far, board.d files were having execute bit set and contained a shebang. However, they are just sourced in board_detect, with an apparantly unnecessary check for execute permission beforehand. Replace this check by one for existance and make the board.d files "normal" files, as would be expected in /etc anyway. Note: This removes an apparantly unused '#!/bin/sh /etc/rc.common' in target/linux/bcm47xx/base-files/etc/board.d/01_network Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: net: phy: qca807x: fix GPIO driverRobert Marko2021-03-051-0/+1
| | | | | | | | | | | While rebasing into setting bits instead of magic values, I accidentally forgot to actually set the force bit. Without it using the pins as GPIO-s did not actually work. Fixes: b5c93ed ("ipq40xx: add Qualcomm QCA807x driver") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* kernel-5.4: bump to 5.4.102 and refresh patchesJason A. Donenfeld2021-03-041-1/+1
| | | | | | | | | | | | | | 5.4.102 backported a lot of stuff that our WireGuard backport already did, in addition to other patches we had, so those patches were removed from that part of the series. In the process other patches were refreshed or reworked to account for upstream changes. This commit involved `update_kernel.sh -v -u 5.4`. Cc: John Audia <graysky@archlinux.us> Cc: David Bauer <mail@david-bauer.net> Cc: Petr Štetiar <ynezz@true.cz> Signed-off-by: Jason A. Donenfeld <Jason@zx2c4.com>
* treewide: remove redundant KERNEL_PREFIX definitionsPaul Spooren2021-02-231-2/+0
| | | | | | | | | | The variables KERNEL_INITRAMFS_PREFIX and KERNEL_PREFIX are already defined in include/image.mk and don't have to be redefined in the target Makefiles. Signed-off-by: Paul Spooren <mail@aparcar.org> [also cover imx6] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: remove generic profileAdrian Schmutzler2021-01-271-9/+0
| | | | | | | | | | | On a platform with many very different devices, like found on ipq40xx, the generic profile seems like a remnant of the past that does not have a real use anymore. Remove it to have one thing less to maintain. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: fix boards being shown twiceRobert Marko2021-01-211-2/+0
| | | | | | | | | | | | | | | | Since generic images have been split to their own Makefile boards are showing up twice in menuconfig as $(eval $(call BuildImage)) was not dropped from the new generic.mk. Hence $(eval $(call BuildImage)) was being called twice. So, lets simply drop it from generic.mk. Fixes: 378c7ff28210 ("ipq40xx: split generic images into own file") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: mikrotik: enable MikroTik platform driverRobert Marko2021-01-171-0/+2
| | | | | | | | This enables the MikroTik platform driver, it enables us to parse valuable info from hard_config including WLAN calibration data extraction from sysfs. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: mikrotik: enable MikroTik NOR parserRobert Marko2021-01-171-0/+1
| | | | | | Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTSRobert Marko2021-01-171-0/+1
| | | | | | | | | This enables the new MikroTik specific partition parser. This avoids manually specifying the MikroTik specific partitions as they can be detected by their magic values. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add MikroTik subtargetRobert Marko2021-01-173-1/+5
| | | | | | | | | | | | | MikroTik devices require the use of raw vmlinux out of the self extracting compressed kernels. They also require 4K sectors, kernel2minor, partition parser as well as RouterBoard platform drivers. So in order to not add unnecessary code to the generic sub target lets introduce a MikroTik sub target. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: kernel compressed boot: reset watchdog countdownJohn Thomson2021-01-171-0/+66
| | | | | | | | | | | | | | If the watchdog is enabled, set the timeout to 30 seconds before decompress is started. Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog enabled and running with a timeout that does not allow time for the kernel to decompress and manage the watchdog. On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before: Jumping to kernel Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* ipq40xx: arm: compressed: add appended DTB sectionRobert Marko2021-01-171-0/+48
| | | | | | | | | | | | | | | | | | | | This adds a appended_dtb section to the ARM decompressor linker script. This allows using the existing ARM zImage appended DTB support for appending a DTB to the raw ELF kernel. Its size is set to 1MB max to match the zImage appended DTB size limit. To use it to pass the DTB to the kernel, objcopy is used: objcopy --set-section-flags=.appended_dtb=alloc,contents \ --update-section=.appended_dtb=<target>.dtb vmlinux This is based off the following patch: https://github.com/openwrt/openwrt/commit/c063e27e02a9dcac0e7f5877fb154e58fa3e1a69 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: split generic images into own fileAlexander Couzens2021-01-172-806/+810
| | | | | | | In preparation of the new mikrotik subtarget split the generic images into generic.mk Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* uboot-envtools: add support for Aruba AP-303 and AP-365Jan Alexander2021-01-143-4/+2
| | | | | | | | | Both devices use u-boot env variables to boot OpenWrt from its flash partition. Using u-boot envtools, it is possible to change the bootcmd back to the stock firmware partition directly from OpenWrt without attaching a serial cable or even physically accessing the device. Signed-off-by: Jan Alexander <jan@nalx.net>
* ipq40xx: remove unnecessary execute permission bitSungbo Eo2021-01-031-0/+0
| | | | | | | | | DTS files do not need to be executable. 644 is enough. Fixes: 0fbdb51f7643 ("ipq40xx: add Edgecore OAP-100 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [split by targets] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.86Adrian Schmutzler2021-01-012-3/+3
| | | | | | | | | | | | | | | | | Removed upstreamed patches: pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch Manually merged: pending-5.4/611-netfilter_match_bypass_default_table.patch layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64 Run-tested: ipq806x/R7800, realtek Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org>
* ipq40xx: remove non-existent ethernet PHYDavid Bauer2020-12-302-0/+8
| | | | | | | | | Since updating the MDIO driver, the probe will fail hard on any PHY not present on the bus, while this was not the case prior. Fixes commit 26b1f72381fb ("ipq40xx: net: phy: ar40xx: remove PHY handling") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-256-1/+290
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq40xx: net: ethernet: edma: use generic PHY printRobert Marko2020-12-231-2/+2
| | | | | | | | | | | | | Lets use the generic upstream phy_print_status() instead of doing something similar by hand. Before: ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000 After: ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: use generic ksettings functionsRobert Marko2020-12-231-56/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since we now have a proper PHY driver for QCA807x and AR803x has already been supported properly there is no need for the driver to be poking on PHY registers for ethtool ops. So, lets simply use the generic phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions. This also has the advantage of properly populating stuff other than speeds like, transceiver type, MDI-X etc. ethtool before: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes ethtool after: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Receive-only Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: external Auto-negotiation: on MDI-X: off (auto) Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: dts: convert PHY GPIO bindingsRobert Marko2020-12-232-22/+41
| | | | | | | | | | Since the new PHY driver manages each PHY individually and therefore registers each PHY that is marked with gpio-controller; DT property as a GPIO controller we need to convert old DT bindings to account for this. Only 2 boards use this so its not much of an issue. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: dts: add QCA807x propertiesRobert Marko2020-12-232-2/+64
| | | | | | | | This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI. Also adds the PSGMII PHY as it wont get probed otherwise. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: fix link detectionRobert Marko2020-12-231-0/+4
| | | | | | | PHY needs to be soft reset before starting it from ethernet driver as AR40xx calibration will leave it in unwanted state. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: phy: ar40xx: remove PHY handlingRobert Marko2020-12-232-229/+20
| | | | | | | | | | | | | | | Since we now have proper PHY driver for the QCA807x PHY-s, lets remove PHY handling from AR40xx. This removes PHY driver, PHY GPIO driver and PHY init code. AR40xx still needs to handle PSGMII calibration as that requires R/W from the switch, so I am unable to move it into PHY driver. This also converted the AR40xx driver to use OF_MDIO to find the MDIO bus as it now cant be set through the PHY driver. So lets depend on OF_MDIO in KConfig. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add Qualcomm QCA807x driverRobert Marko2020-12-234-0/+940
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s. They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC, while second one is SGMII for connection to MAC or fiber. Both models have a combo port that supports 1000BASE-X and 100BASE-FX fiber. Each PHY inside of QCA807x series has 2 digitally controlled output only pins that natively drive LED-s. But some vendors used these to driver generic LED-s controlled by user space, so lets enable registering each PHY as GPIO controller and add driver for it. This also adds the ability to specify DT properties so that 1000 Base-T LED will also be lit up for 100 and 10 Base connections. This is usually done by U-boot, but boards running mainline U-boot are not configuring this yet. These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x boards. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: edma: convert to of_mdio_find_bus()Robert Marko2020-12-232-23/+7
| | | | | | | | | | | | | | With the reworked MDIO driver, EDMA will fail to get the MII BUS as it used the MII BUS stored inside the MDIO structure private data. This obviously does not work with the modernized driver, so lets switch to using a purpose build of_mdio_find_bus() which will return the MII BUS and only requires the MDIO node to be passed. This is easy as we already have the node parsed. Also, since we now require OF_MDIO add that as dependency. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-15 17:51:37 +0000