aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* treewide: provide global default for SUPPORTED_DEVICESAdrian Schmutzler2021-01-231-1/+0
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The majority of our targets provide a default value for the variable SUPPORTED_DEVICES, which is used in images to check against the compatible on a running device: SUPPORTED_DEVICES := $(subst _,$(comma),$(1)) At the moment, this is implemented in the Device/Default block of the individual targets or even subtargets. However, since we standardized device names and compatible in the recent past, almost all targets are following the same scheme now: device/image name: vendor_model compatible: vendor,model The equal redundant definitions are a symptom of this process. Consequently, this patch moves the definition to image.mk making it a global default. For the few targets not using the scheme above, SUPPORTED_DEVICES will be defined to a different value in Device/Default anyway, overwriting the default. In other words: This change is supposed to be cosmetic. This can be used as a global measure to get the current compatible with: $(firstword $(SUPPORTED_DEVICES)) (Though this is not precisely an achievement of this commit.) Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: fix boards being shown twiceRobert Marko2021-01-211-2/+0
| | | | | | | | | | | | | | | | Since generic images have been split to their own Makefile boards are showing up twice in menuconfig as $(eval $(call BuildImage)) was not dropped from the new generic.mk. Hence $(eval $(call BuildImage)) was being called twice. So, lets simply drop it from generic.mk. Fixes: 378c7ff28210 ("ipq40xx: split generic images into own file") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: mikrotik: enable MikroTik platform driverRobert Marko2021-01-171-0/+2
| | | | | | | | This enables the MikroTik platform driver, it enables us to parse valuable info from hard_config including WLAN calibration data extraction from sysfs. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: mikrotik: enable MikroTik NOR parserRobert Marko2021-01-171-0/+1
| | | | | | Needed for SPI-NOR based MikroTik IPQ40xx devices like hAP ac2. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: mikrotik: enable CONFIG_MTD_ROUTERBOOT_PARTSRobert Marko2021-01-171-0/+1
| | | | | | | | | This enables the new MikroTik specific partition parser. This avoids manually specifying the MikroTik specific partitions as they can be detected by their magic values. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add MikroTik subtargetRobert Marko2021-01-173-1/+5
| | | | | | | | | | | | | MikroTik devices require the use of raw vmlinux out of the self extracting compressed kernels. They also require 4K sectors, kernel2minor, partition parser as well as RouterBoard platform drivers. So in order to not add unnecessary code to the generic sub target lets introduce a MikroTik sub target. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: kernel compressed boot: reset watchdog countdownJohn Thomson2021-01-171-0/+66
| | | | | | | | | | | | | | If the watchdog is enabled, set the timeout to 30 seconds before decompress is started. Mikrotik ipq40xx devices running with RouterBoot have the SoC watchdog enabled and running with a timeout that does not allow time for the kernel to decompress and manage the watchdog. On ipq40xx RouterBoot TFTP boot the watchdog countdown is reset before: Jumping to kernel Signed-off-by: John Thomson <git@johnthomson.fastmail.com.au>
* ipq40xx: arm: compressed: add appended DTB sectionRobert Marko2021-01-171-0/+48
| | | | | | | | | | | | | | | | | | | | This adds a appended_dtb section to the ARM decompressor linker script. This allows using the existing ARM zImage appended DTB support for appending a DTB to the raw ELF kernel. Its size is set to 1MB max to match the zImage appended DTB size limit. To use it to pass the DTB to the kernel, objcopy is used: objcopy --set-section-flags=.appended_dtb=alloc,contents \ --update-section=.appended_dtb=<target>.dtb vmlinux This is based off the following patch: https://github.com/openwrt/openwrt/commit/c063e27e02a9dcac0e7f5877fb154e58fa3e1a69 Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: split generic images into own fileAlexander Couzens2021-01-172-806/+810
| | | | | | | In preparation of the new mikrotik subtarget split the generic images into generic.mk Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* uboot-envtools: add support for Aruba AP-303 and AP-365Jan Alexander2021-01-143-4/+2
| | | | | | | | | Both devices use u-boot env variables to boot OpenWrt from its flash partition. Using u-boot envtools, it is possible to change the bootcmd back to the stock firmware partition directly from OpenWrt without attaching a serial cable or even physically accessing the device. Signed-off-by: Jan Alexander <jan@nalx.net>
* ipq40xx: remove unnecessary execute permission bitSungbo Eo2021-01-031-0/+0
| | | | | | | | | DTS files do not need to be executable. 644 is enough. Fixes: 0fbdb51f7643 ("ipq40xx: add Edgecore OAP-100 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> [split by targets] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.86Adrian Schmutzler2021-01-012-3/+3
| | | | | | | | | | | | | | | | | Removed upstreamed patches: pending-5.4/499-mtd-parser-cmdline-Fix-parsing-of-part-names-with-co.patch Manually merged: pending-5.4/611-netfilter_match_bypass_default_table.patch layerscape/302-dts-0112-arm64-dts-fsl-ls1028a-prepare-dts-for-overlay.patch Build-tested: ipq806x/R7800, bcm27xx/bcm2711, ath79/{generic,tiny}, ipq40xx, octeon, ramips/mt7621, realtek, x86/64 Run-tested: ipq806x/R7800, realtek Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Tested-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org>
* ipq40xx: remove non-existent ethernet PHYDavid Bauer2020-12-302-0/+8
| | | | | | | | | Since updating the MDIO driver, the probe will fail hard on any PHY not present on the bus, while this was not the case prior. Fixes commit 26b1f72381fb ("ipq40xx: net: phy: ar40xx: remove PHY handling") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for GL.iNet GL-AP1300Dongming Han2020-12-256-1/+290
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: Reset LED: Power, Internet UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 OTHER: On board with BLE module - by cp210x USB serial chip On board hareware watchdog with GPIO0 high to turn on, and GPIO4 for watchdog feed Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-ap1300-squashfs-nand-factory.ubi (IPQ40xx) # run lf By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Dongming Han <handongming@gl-inet.com>
* ipq40xx: net: ethernet: edma: use generic PHY printRobert Marko2020-12-231-2/+2
| | | | | | | | | | | | | Lets use the generic upstream phy_print_status() instead of doing something similar by hand. Before: ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=1000 After: ess_edma c080000.edma eth1: Link is Up - 1Gbps/Full - flow control rx/tx Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: use generic ksettings functionsRobert Marko2020-12-231-56/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Since we now have a proper PHY driver for QCA807x and AR803x has already been supported properly there is no need for the driver to be poking on PHY registers for ethtool ops. So, lets simply use the generic phy_ethtool_ksettings_get/phy_ethtool_ksettings_set functions. This also has the advantage of properly populating stuff other than speeds like, transceiver type, MDI-X etc. ethtool before: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: No Link partner advertised auto-negotiation: No Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: internal Auto-negotiation: on MDI-X: Unknown Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes ethtool after: root@OpenWrt:/# ethtool eth1 Settings for eth1: Supported ports: [ TP MII ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Supported pause frame use: Symmetric Receive-only Supports auto-negotiation: Yes Supported FEC modes: Not reported Advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full 1000baseX/Full Advertised pause frame use: Symmetric Receive-only Advertised auto-negotiation: Yes Advertised FEC modes: Not reported Link partner advertised link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Link partner advertised pause frame use: Symmetric Receive-only Link partner advertised auto-negotiation: Yes Link partner advertised FEC modes: Not reported Speed: 1000Mb/s Duplex: Full Port: Twisted Pair PHYAD: 4 Transceiver: external Auto-negotiation: on MDI-X: off (auto) Supports Wake-on: d Wake-on: d Current message level: 0x00000000 (0) Link detected: yes Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: dts: convert PHY GPIO bindingsRobert Marko2020-12-232-22/+41
| | | | | | | | | | Since the new PHY driver manages each PHY individually and therefore registers each PHY that is marked with gpio-controller; DT property as a GPIO controller we need to convert old DT bindings to account for this. Only 2 boards use this so its not much of an issue. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: dts: add QCA807x propertiesRobert Marko2020-12-232-2/+64
| | | | | | | | This adds necessary DT properties for QCA807x PHY-s to IPQ4019 DTSI. Also adds the PSGMII PHY as it wont get probed otherwise. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: ethernet: edma: fix link detectionRobert Marko2020-12-231-0/+4
| | | | | | | PHY needs to be soft reset before starting it from ethernet driver as AR40xx calibration will leave it in unwanted state. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: net: phy: ar40xx: remove PHY handlingRobert Marko2020-12-232-229/+20
| | | | | | | | | | | | | | | Since we now have proper PHY driver for the QCA807x PHY-s, lets remove PHY handling from AR40xx. This removes PHY driver, PHY GPIO driver and PHY init code. AR40xx still needs to handle PSGMII calibration as that requires R/W from the switch, so I am unable to move it into PHY driver. This also converted the AR40xx driver to use OF_MDIO to find the MDIO bus as it now cant be set through the PHY driver. So lets depend on OF_MDIO in KConfig. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add Qualcomm QCA807x driverRobert Marko2020-12-234-0/+940
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds driver for the Qualcomm QCA8072 and QCA8075 PHY-s. They are 2 or 5 port IEEE 802.3 clause 22 compliant 10BASE-Te, 100BASE-TX and 1000BASE-T PHY-s. They feature 2 SerDes, one for PSGMII or QSGMII connection with MAC, while second one is SGMII for connection to MAC or fiber. Both models have a combo port that supports 1000BASE-X and 100BASE-FX fiber. Each PHY inside of QCA807x series has 2 digitally controlled output only pins that natively drive LED-s. But some vendors used these to driver generic LED-s controlled by user space, so lets enable registering each PHY as GPIO controller and add driver for it. This also adds the ability to specify DT properties so that 1000 Base-T LED will also be lit up for 100 and 10 Base connections. This is usually done by U-boot, but boards running mainline U-boot are not configuring this yet. These PHY-s are commonly used in Qualcomm IPQ40xx, IPQ60xx and IPQ807x boards. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: edma: convert to of_mdio_find_bus()Robert Marko2020-12-232-23/+7
| | | | | | | | | | | | | | With the reworked MDIO driver, EDMA will fail to get the MII BUS as it used the MII BUS stored inside the MDIO structure private data. This obviously does not work with the modernized driver, so lets switch to using a purpose build of_mdio_find_bus() which will return the MII BUS and only requires the MDIO node to be passed. This is easy as we already have the node parsed. Also, since we now require OF_MDIO add that as dependency. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: backport upstream MDIO driverRobert Marko2020-12-234-226/+211
| | | | | | | | | IPQ40xx MDIO driver was upstreamed in kernel version 5.8. So lets backport the upstream version and drop our local one. This also refreshed the kernel config since the symbol name has changed. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: refresh kernel configRobert Marko2020-12-231-66/+0
| | | | | | | Generic kernel config changed a lot, so lets refresh ipq40xx to reduce the diff. Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: add support for devolo Magic 2 WiFi nextStefan Schake2020-12-226-1/+307
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v71) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8075 (2 ports) PLC: MaxLinear G.hn 88LX5152 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET, WiFi, PLC Button LEDS: red/white home, white WiFi To modify a retail device to run OpenWRT firmware: 1) Setup a TFTP server on IP address 192.168.0.100 and copy the OpenWRT initramfs (initramfs-fit-uImage.itb) to the TFTP root as 'uploadfile'. 2) Power on the device while pressing the recessed reset button next to the Ethernet ports. This causes the bootloader to retrieve and start the initramfs. 3) Once the initramfs is booted, the device will come up with IP 192.168.1.1. You can then connect through SSH (allow some time for the first connection). 4) On the device shell, run 'fw_printenv' to show the U-boot environment. Backup this information since it contains device unique factory data. 5) Change the boot command to support booting OpenWRT: # fw_setenv bootcmd 'sf probe && sf read 0x84000000 0x180000 0x400000 && bootm' 6) Change directory to /tmp, download the sysupgrade (e.g. through wget) and install it with sysupgrade. The device will reboot into OpenWRT. Notice that there is currently no support for booting the G.hn chip. This requires userland software we lack the rights to share right now. Signed-off-by: Stefan Schake <stefan.schake@devolo.de>
* ipq40xx: add support for Plasma Cloud PA2200Marek Lindner2020-12-227-4/+237
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA2200 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=PlasmaCloud-PA2200 * GPIO-LEDs for 2.4GHz, 5GHz-SoC and 5GHz-PCIE * GPIO-LEDs for power (orange) and status (blue) * 1x GPIO-button (reset) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3at POE+ + used as WAN interface * 12V 2A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: add support for Plasma Cloud PA1200Marek Lindner2020-12-227-3/+222
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Device specifications: * QCA IPQ4018 * 256 MB of RAM * 32 MB of SPI NOR flash (w25q256) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=PlasmaCloud-PA1200 * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=PlasmaCloud-PA1200 * 3x GPIO-LEDs for status (cyan, purple, yellow) * 1x GPIO-button (reset) * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio4: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + used as LAN interface - phy@mdio3: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 802.3af/at POE(+) + used as WAN interface * 12V/24V 1A DC Flashing instructions: The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. Signed-off-by: Marek Lindner <marek.lindner@kaiwoo.ai> [sven@narfation.org: prepare commit message, rebase, use all LEDs, switch to dualboot_datachk upgrade script, use eth1 as designated WAN interface] Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Change name for openmesh.sh to vendor-free nameSven Eckelmann2020-12-222-5/+5
| | | | | | | | | Other vendors are using functionality similar to the ones OpenMesh used to implement two areas on the flash to store the default image and a fallback image. So just change the name to dualboot_datachk.sh to avoid duplicated code just to have the same script for different vendors. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: move some disabled symbols to genericAleksander Jan Bajkowski2020-12-221-2/+0
| | | | | | Move some disabled config options found in lantiq target to generic. Signed-off-by: Aleksander Jan Bajkowski <A.Bajkowski@stud.elka.pw.edu.pl>
* ipq40xx: use upper case for NETGEAR in DEVICE_VENDORMoritz Warning2020-12-191-2/+1
| | | | | | | | | | Adjust spelling of vendor name to what is used in other places. Also move definition in shared section. Signed-off-by: Moritz Warning <moritzwarning@web.de> [improve commit title/message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.83John Audia2020-12-151-1/+1
| | | | | | | | | | | | | | | | | | | Manually merged: layerscape/808-i2c-0011-i2c-imx-support-slave-mode-for-imx-I2C-driver.patch layerscape/808-i2c-0012-i2c-imx-correct-code-of-errata-A-010650-for-layersca.patch Remaining modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, x86/64 [*], ramips/mt7621 [*], ath79/tiny [*], ipq40xx [*], octeon [*], realtek [*] Run-tested: ipq806x/R7800, ramips/mt7621 [*], octeon [*], realtek [*] No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Tested-by: Stijn Segers <foss@volatilesystems.org> [*]
* ipq40xx: revert usage of VLAN S-TAGDavid Bauer2020-12-142-37/+9
| | | | | | | | | | | This reverts the usage of the S-Tag for separating LAN and WAN port on the embedded switch. Many users complained about not being able to manage C-Tag addition / removal on the switch as well as degraded performance. Fixes: commit 9da2b567605b ("ipq40xx: fix ethernet vlan double tagging") Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix 5Ghz tx/rx power on the ASUS MAP-AC2200Yushi Nishida2020-12-131-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | The ASUS MAP-AC2200 suffers from a lower transmit/receive signal power as compared to the stock firmware. Upon investigation, it was discovered that stock firmware from the GPL_MAP-AC2200_3.0.0.4.384.46249-g97d05bb.tar archive. set the following GPIOs in "release/src/router/rc/init.c". GPIO 44 and 46 have to be set to output high GPIO 45 and 47 have to be set to output low Here are some results, after activating the relevant gpios through cmdline: <https://forum.openwrt.org/t/asus-map-ac2200-low-transmit-receive-signal-5ghz/69005/12> THX @ slh Fixes: 9ad3967f140 ("ipq40xx: add support for ASUS Lyra") Signed-off-by: Yushi Nishida <kyro2man@gmx.net> [slightly rewritten commit, added missing <>) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: DTS style updates for OpenMesh devicesSven Eckelmann2020-11-233-47/+18
| | | | | | | | | | | | | | | | | The OpenMesh related files were not updated since a while and the new coding style requirements weren't integrated. This can cause problems for new devices when an author uses these files as starting point. * use SPDX-License-Identifiers instead of full license texts * drop linux,default-trigger with value default-off for LEDs * led nodes with label "abc:xyz" should have name "xyz_abc" * led DT labels for "xyz_abc" should be "led_xyz_abc" * "m25p80@0" flash node should be renamed to "flash@0" * drop unnecessary empty lines Signed-off-by: Sven Eckelmann <sven@narfation.org> [minor commit title and message adjustments] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.77John Audia2020-11-182-4/+4
| | | | | | | | | | | | | | | | | | | | | | | | Manually rebased patches: bcm27xx/patches-5.4/950-0135-spi-spi-bcm2835-Disable-forced-software-CS.patch generic-backport/744-v5.5-net-sfp-soft-status-and-control-support.patch layerscape/patches-5.4/819-uart-0005-tty-serial-fsl_lpuart-enable-dma-mode-for-imx8qxp.patch mvebu/patches-5.4/521-arm64-dts-marvell-espressobin-Add-ethernet-switch-al.patch Removed: layerscape/patches-5.4/819-uart-0012-tty-serial-lpuart-add-LS1028A-support.patch All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, lantiq/Easybox 904 xDSL, x86_64 Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL, x86_64 No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> Co-developed-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: do not remove pci@40000000 for ap.dk04.1Adrian Schmutzler2020-11-131-6/+6
| | | | | | | | | | | | | | This pci@40000000 node from upstream was dropped when the device was converted from local DTS(I) files to kernel patches in [1] to ensure that change was purely cosmetic. However, the DK04.1 has a PCI-E slot by default, so let's keep (i.e. not remove) the kernel definition now. [1] c4beac9ea2e1 ("ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1") Suggested-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: 5.4: update and reorder patchesRobert Marko2020-11-1333-432/+423
| | | | | | | | | | | | | | A lot of patches are outdated versions of upstreamed patches and drivers. So lets pull in the upstreamed patches and reorder remaining ones. This drops the unnecessary 721-dts-ipq4019-add-ethernet-essedma-node.patch which adds nodes for not yet in OpenWrt IPQESS driver. Signed-off-by: Robert Marko <robert.marko@sartura.hr> [do not touch 902-dts-ipq4019-ap-dk04.1.patch here] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: enable RX hash / CTAG TX offloading for single-phyDavid Bauer2020-11-011-0/+9
| | | | | | | | | | | | This re-enables offloading features disabled by commit 9da2b567605b ("ipq40xx: fix ethernet vlan double tagging"). Single-PHY devices use port-based VLANs on the switch, therefore no S-TAG magic is involved here. Re-enabling these features restores throughput back to 950 Mbit/s. Reported-by: Jannis Pinter <jannis@pinterjann.is> Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: remove support for kernel 4.19Adrian Schmutzler2020-10-1952-12169/+0
| | | | | | | | | | The target uses 5.4 as default kernel since 03/2020. Kernel 4.19 support is not really maintained anymore, it does not seem to be needed, and removing it will make upcoming driver updates easier. Thus, remove it. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* kernel: bump 5.4 to 5.4.71John Audia2020-10-152-2/+2
| | | | | | | | | | | | | | | All modifications made by update_kernel.sh Build system: x86_64 Build-tested: ipq806x/R7800, ath79/generic, bcm27xx/bcm2711, lantiq/Easybox 904 xDSL Run-tested: ipq806x/R7800, lantiq/Easybox 904 xDSL No dmesg regressions, everything functional Signed-off-by: John Audia <graysky@archlinux.us> [add lantiq test reports] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* treewide: enable the vDSORui Salvaterra2020-10-132-2/+0
| | | | | | | The vDSO is used to accelerate some syscalls. It should work fine wherever it's available, so enable it globally for all targets. Signed-off-by: Rui Salvaterra <rsalvaterra@gmail.com>
* ipq40xx: 5.4: move AR40xx driver into filesRobert Marko2020-10-093-2466/+2460
| | | | | | | | | | | | There is no point in keeping the AR40xx driver as a patch as its not pending merge or backport. To allow for easier maintenance until DSA is ready move it into files like EDMA is. Signed-off-by: Robert Marko <robert.marko@sartura.hr> [combine with removal from patches-5.4] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: use upstream DTS files for IPQ4019/AP-DK04.1Adrian Schmutzler2020-10-073-202/+167
| | | | | | | | | | | | | | Upstream provides DTS(I) files for IPQ4019/AP-DK04.1, but we overwrite them with local versions so far. Remove the local files and use patches to be closer to upstream. We already do the same for IPQ40xx/AP-DK01.1-C1. Technically, this changes the compatible from "qcom,ipq4019" to "qcom,ipq4019-dk04.1-c1", but it has never been implemented correctly beforehand anyway. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: improve support for Edgecore ECW5211Sungbo Eo2020-10-073-37/+34
| | | | | | | | | | | | | | | | | | | This adds several stylistic and functional improvements of the recently added Edgecore ECW5211, especially: * Drop the local BDFs as those are already in the upstream under different names * Add SPDX tag to DTS * Add label MAC address * Move LED trigger to DTS * Remove unnecessary status="okay" * Disable unused SS USB phy as the USB port only supports USB 2.0 * Make uboot-env partition writable * Remove qcom,poll_required_dynamic property as the driver does not use it * Tidy up the device recipe Fixes: 4488b260a02e ("ipq40xx: add Edgecore ECW5211 support") Signed-off-by: Sungbo Eo <mans0n@gorani.run> Acked-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: remove model name from LED labelsAdrian Schmutzler2020-10-0740-218/+233
| | | | | | | | | | | Like in the previous patches for ath79 and ramips, this will remove the "devicename" from LED labels in ipq40xx. The devicename is removed in DTS files and 01_leds, and a migration script is added. While at it, also harmonize capitalization of wlan2G/wlan5G vs. wlan2g/wlan5g. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: tidy up device recipe for Edgecore OAP100Sungbo Eo2020-09-261-2/+3
| | | | | | | * split up DEVICE_TITLE into DEVICE_{VENDOR,MODEL} * use SOC instead of DEVICE_DTS Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: tidy up dts-v1 statementsAdrian Schmutzler2020-09-258-16/+1
| | | | | | | | | | | | | | | | | | | | | The "/dts-v1/;" identifier is supposed to be present once at the top of a device tree file after the includes have been processed. Therefore, adding it to a DTS _and_ a DTSI file is actually wrong, as it will be present twice then (though the compiler does not complain about it). In ipq40xx, the dts-v1 statement is already included in qcom-ipq4019.dtsi, so we don't have to add it anywhere at all. However, based on the conditions stated above, this requires qcom-ipq4019.dtsi to be included as the first file in any DTS(I). Consequently, this patch removes all cases of dts-v1 for the ipq40xx target, and moves the includes accordingly where necessary. While at it, remove a few obviously unneeded includes on the way. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: fix DTS warning in qcom-ipq4029-gl-s1300.dtsChristian Lamparter2020-09-251-1/+1
| | | | | | | .dts:226.17-230.4: Warning (spi_bus_reg): /soc/spi@78b6000/spi@1: SPI bus unit address format error, expected "0" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix DTS warning in qcom-ipq4019-cm520-79f.dtsChristian Lamparter2020-09-251-1/+1
| | | | | | | | | | | | .dts:121.4-14: Warning (reg_format): /led_spi/led_gpio@0:reg: \ property has invalid length (4 bytes) (#address-cells == 1, #size-cells == 1) .dtb: Warning (pci_device_bus_num): Failed prerequisite 'reg_format' .dtb: Warning (i2c_bus_reg): Failed prerequisite 'reg_format' .dtb: Warning (spi_bus_reg): Failed prerequisite 'reg_format' .dts:119.24-126.5: Warning (avoid_default_addr_size): /led_spi/led_gpio@0: \ Relying on default #size-cells value Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: Add support for Linksys MR8300 (Dallas)Hans Geiblinger2020-09-2512-314/+421
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys MR8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Hardware Highlights: SoC: IPQ4019 at 717 MHz (4 CPUs) RAM: 512MB RAM SoC: Qualcomm IPQ4019 at 717 MHz (4 CPUs) RAM: 512M DDR3 FLASH: 256 MB NAND (Winbond W29N02GV, 8-bit parallel) ETH: Qualcomm QCA8075 (4x GigE LAN, 1x GigE Internet Ethernet Jacks) BTN: Reset and WPS USB: USB3.0, single port on rear with LED SERIAL: Serial pads internal (unpopulated) LED: Four status lights on top + USB LED WIFI1: 2x2:2 QCA4019 2.4 GHz radio on ch. 1-14 WIFI2: 2x2:2 QCA4019 5 GHz radio on ch. 36-64 WIFI3: 2x2:2 QCA9888 5 GHz radio on ch. 100-165 Support is based on the already supported EA8300. Key differences: EA8300 has 256MB RAM where MR8300 has 512MB RAM. MR8300 has a revised top panel LED setup. Installation: "Factory" images may be installed directly through the OEM GUI using URL: https://ip-of-router/fwupdate.html (Typically 192.168.1.1) Signed-off-by: Hans Geiblinger <cybrnook2002@yahoo.com> [copied Hardware-highlights from EA8300. Fixed alphabetical order. fixed commit subject, removed bogus unit-address of keys, fixed author (used Signed-off-By to From:) ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>