aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: Linksys: sysupgrade: Ensure OEM volumes are removedJeff Kletsky2019-06-241-20/+22
| | | | | | | | | | | | | | | | | | When OEM volumes are present in the [alt_]firmware partition, sysupgrade will write a new kernel, but will fail to write the root file system. The next boot will hang indefinitely Waiting for root device /dev/ubiblock0_0... Modified ipq40xx/base-files/lib/upgrade/linksys.sh to remove both `squashfs` and `ubifs` if found on the target firmware partition's UBI device. Run-tested-on: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [applied some shellcheck suggestions as well]
* kernel: drop everything not on kernel version 4.14Daniel Golle2019-06-1256-15908/+0
| | | | | | | | | | * Remove testing patches for kernel version 4.19 * remove targets ar7, ixp4xx, orion Those targets are still on kernel 4.9, patches for 4.14 were not ready in time. They may be readded once people prepare and test patches for kernel 4.14. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Add support for Linksys EA8300 (Dallas)Jeff Kletsky2019-05-1811-11/+847
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Linksys EA8300 is based on QCA4019 and QCA9888 and provides three, independent radios. NAND provides two, alternate kernel/firmware images with fail-over provided by the OEM U-Boot. Installation: "Factory" images may be installed directly through the OEM GUI. Hardware Highlights: * IPQ4019 at 717 MHz (4 CPUs) * 256 MB NAND (Winbond W29N02GV, 8-bit parallel) * 256 MB RAM * Three, fully-functional radios; `iw phy` reports (FCC/US, -CT): * 2.4 GHz radio at 30 dBm * 5 GHz radio on ch. 36-64 at 23 dBm * 5 GHz radio on ch. 100-144 at 23 dBm (DFS), 149-165 at 30 dBm #{ managed } <= 16, #{ AP, mesh point } <= 16, #{ IBSS } <= 1 * All two-stream, MCS 0-9 * 4x GigE LAN, 1x GigE Internet Ethernet jacks with port lights * USB3, single port on rear with LED * WPS and reset buttons * Four status lights on top * Serial pads internal (unpopulated) "Linksys Dallas WiFi AP router based on Qualcomm AP DK07.1-c1" Implementation Notes: The OEM flash layout is preserved at this time with 3 MB kernel and ~69 MB UBIFS for each firmware version. The sysdiag (1 MB) and syscfg (56 MB) partitions are untouched, available as read-only. Serial Connectivity: Serial connectivity is *not* required to flash. Serial may be accessed by opening the device and connecting a 3.3-V adapter using 115200, 8n1. U-Boot access is good, including the ability to load images over TFTP and either run or flash them. Looking at the top of the board, from the front of the unit, J3 can be found on the right edge of the board, near the rear | J3 | |-| | |O| | (3.3V seen, open-circuit) |O| | TXD |O| | RXD |O| | |O| | GND |-| | | Unimplemented: * serial1 "ttyQHS0" (serial0 works as console) * Bluetooth; Qualcomm CSR8811 (potentially conected to serial1) Other Notes: https://wikidevi.com/wiki/Linksys_EA8300 states FCC docs also cover the Linksys EA8250. According to the RF Test Report BT BR+EDR, "All models are identical except for the EA8300 supports 256QAM and the EA8250 disable 256QAM." Signed-off-by: Jeff Kletsky <git-commits@allycomm.com>
* mtd: base-files: Unify dual-firmware devices (Linksys)Jeff Kletsky2019-05-183-52/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Consistently handle boot-count reset and upgrade across ipq40xx, ipq806x, kirkwood, mvebu Dual-firmware devices often utilize a specific MTD partition to record the number of times the boot loader has initiated boot. Most of these devices are NAND, typically with a 2k erase size. When this code was ported to the ipq40xx platform, the device in hand used NOR for this partition, with a 16-byte "record" size. As the implementation of `mtd resetbc` is by-platform, the hard-coded nature of this change prevented proper operation of a NAND-based device. * Unified the "NOR" variant with the rest of the Linksys variants * Added logging to indicate success and failure * Provided a meaningful return value for scripting * "Protected" the use of `mtd resetbc` in start-up scripts so that failure does not end the boot sequence * Moved Linksys-specific actions into common `/etc/init.d/bootcount` For upgrade, these devices need to determine which partition to flash, as well as set certain U-Boot envirnment variables to change the next boot to the newly flashed version. * Moved upgrade-related environment changes out of bootcount * Combined multiple flashes of environment into single one * Current-partition detection now handles absence of `boot_part` Runtime-tested: Linksys EA8300 Signed-off-by: Jeff Kletsky <git-commits@allycomm.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [checkpatch.pl fixes, traded split strings for 80+ chars per line]
* kernel: Move some DSA config options to generic configHauke Mehrtens2019-05-141-3/+0
| | | | | | | This moves some new configuration options to the generic kernel configuration instead of configuring them for each target on our own. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add factory image for EnGenius ENS620EXTSteve Glennon2019-05-111-11/+29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Extended mksenaofw to support new "capwap" header structure. This supports flashing from factory 3.0.0, 3.0.1, 3.1.0 and 3.5.5 firmware. Note that the factory image format changes for 3.1 and later firmware, and that the 3.1.0 and 3.5.5 Engenius firmware will refuse the factory_30.bin file. Similarly, the 3.0.0 and 3.0.1 Engenius firmware will refuse the factory_35.bin file. Flashing from the Engenius 3.1.0 firmware with the factory_35.bin firmware has not been tested, as 3.1.0 firmware (Engenius "middleFW") is only intended as part of the upgrade path to 3.5.5 firmware. Modified ipq40xx image Makefile to appropriately invoke mksenaofw with new parameters to configure the capwap header. Note that there is currently no method to return to factory firmware, so this is a one-way street. Path from factory 3.0.0 and 3.0.1 (EnGenius) software to OpenWrt is to navigate to 192.168.1.1 on the stock firmware and navigate to the firmware menu. Then copy the URL you have for that page, something like http://192.168.1.1/cgi-bin/luci/;stok=12345abcdef/admin/system/flashops and replace the trailing /admin/system/flashops with just /easyflashops You should then be presented with a simple "Firmware Upgrade" page. On that page, BE SURE TO CLEAR the "Keep Settings:" checkbox. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_30.bin, click "Upgrade" and on the following page select "Proceed". Path from factory 3.5.5 (EnGenius) software to OpenWrt is simply to use the stock firmware update menu. Choose the openwrt-ipq40xx-engenius_ens620ext-squashfs-factory_35.bin and click "Upload" and "Proceed". The device should then flash the OpenWrt firmware and reboot. Note that this resets the device to a default configuration with Wi-Fi disabled, LAN1/PoE acting as a WAN port (running DHCP client) and LAN2 acting as a LAN port with a DHCP server on 192.168.1.x (AP is at 192.168.1.1) Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [sorry, for unfixing the 80-lines eyesores.]
* ipq40xx: Fix reboot on EnGenius ENS620EXTSteve Glennon2019-05-112-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch works around an issue where reboot would cause the AP to power down and not reboot. The ipq4019 restart controller reboot causes the system to power down and not recover. Fix is to disable the restart controller in the device tree and the device reverts to using the watchdog to perform the reset. The real problem is due to the buggy bootloader that ships with the device. Steve Glennon reported in the PR for this patch: <https://github.com/openwrt/openwrt/pull/2009> that: "the problem was due to a bad u-boot that ships with the device. Using the u-boot that comes with 3.5.5.3 EnGenius factory software now allows the old code (using the do_msm_reboot) to reboot successfully. On to the bad news: Well 3.5.5.3 is a bad path. Finally managed to recover. You CANNOT use prior EnGenius firmware to downgrade. Findings: * They now password protect the serial console with a new, unkown password. * They changed the protection on their walled-garden. I have to use the ssh admin@ip /bin/sh --login to get out of their walled-garden. * Attempts to flash the original 3.0.0 or 3.0.1 EnGenius firmware fail through the UI and sysupgrade. Their firmware update GUI now seem to detect regular openwrt images, but they fail to flash Attempts to flash a normal OpenWrt image with sysupgrade fail. [..] Attempts to sysupgrade with EnGenius firmware fail with the same "mandatory section(s) missing" error, so you cannot downgrade to 3.0.0 or 3.0.1." Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [added valuable findings from github discussion]
* build: add a config option for enabling a testing version of the target kernelFelix Fietkau2019-05-111-0/+1
| | | | | | | If the target supports a newer kernel version that is not used by default yet, it can be enabled with this option Signed-off-by: Felix Fietkau <nbd@nbd.name>
* ipq40xx: essedma: Add fix for memory allocation issuesChristian Lamparter2019-03-242-0/+394
| | | | | | | | | | | | | This patch adds a ChromiumOS 3.18 patch [0] that fixes memory allocation issues under memory pressure by keeping track of missed allocs and rectify the omission at a later date. It also adds ethtool counters for memory allocation failures accounting so this can be verified. [0] <https://chromium.googlesource.com/chromiumos/third_party/kernel/+/d4e1e4ce6801f9eddce056c58f5a288864955265> Reported-by: Chen Minqiang <ptpt52@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for EnGenius ENS620EXTSteve Glennon2019-03-218-3/+548
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M FLASH: 32M SPI NOR W25Q256 ETH: QCA8075 WiFi2: IPQ4018 2T2R 2SS b/g/n WiFi5: IPQ4018 2T2R 2SS n/ac LED: - Power amber - LAN1(PoE) green - LAN2 green - Wi-Fi 2.4GHz green - Wi-Fi 5GHz green BTN: - WPS UART: 115200n8 3.3V J1 VCC(1) - GND(2) - TX(3) - RX(4) Added basic support to get the device up and running for a sysupgrade image only. There is currently no way back to factory firmware, so this is a one-way street to OpenWRT. Install from factory condition is convoluted, and may brick your device: 1) Enable SSH and disable the CLI on the factory device from the web user interface (Management->Advanced) 2) Reboot the device 3) Override the default, limited SSH shell: a) Get into the ssh shell: ssh admin@192.168.1.1 /bin/sh --login b) Change the dropbear script to disable the limited shell. At the empty command prompt type: sed -i '/login_ssh/s/^/#/g’ dropbear /etc/init.d/dropbear restart exit 4) ssh in to a (now-) normal OpenWRT SSH session 5) Flash your built image a) scp openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin admin@192.168.1.1:/tmp/ b) ssh admin@192.168.1.1 c) sysupgrade -n /tmp/openwrt-ipq40xx-engenius_ens620ext-squashfs-sysupgrade.bin 6) After flash completes (it may say "Upgrade failed" followed by "Upgrade completed") and device reboots, log in to newly flashed system. Note you will now need to ssh as root rather than admin. Signed-off-by: Steve Glennon <s.glennon@cablelabs.com> [whitespace fixes, reordered partitions, removed rng node from 4.14, fixed 901-arm-boot-add-dts-files.patch] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: limit frequencies for Asus LyraMarius Genheimer2019-03-132-0/+4
| | | | | | | The Asus Lyra has filters in the antenna paths which limits the usable frequencies on both 5GHz radios. Signed-off-by: Marius Genheimer <mail@f0wl.cc>
* ipq40xx: add support for AVM FRITZ!Repeater 3000David Bauer2019-03-138-4/+547
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M (NANYA NT5CC128M16JR-EK) FLASH: 128M NAND (Macronix MX30LF1G18AC-XKI) ETH: Qualcomm QCA8072 WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac WiFi5: QCA9984 4T4R 4SS n/ac LED: - Connect green/blue/red - Power green BTN: WPS/Connect UART: 115200n8 3.3V VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz3000' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz3000.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ3000.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz3000.bin uboot0 > mtd write /path/to/uboot-fritz3000.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net>
* fritz-tools: add support for IPQ40xx platformDavid Bauer2019-03-131-1/+1
| | | | | | | | AVM devices based on Qualcomm IPQ40xx do not store sector health information in the OOB area. Make this check optional to support this platform. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix FRITZBox 7530 NAND controller nodeDavid Bauer2019-03-132-2/+0
| | | | | | | | This removes the 'cs-gpios' property from the AVM FRITZ!Box 7530 NAND controller node. As pointed out by Christian Lamparter, the property is not needed by the Qualcomm NAND controller driver. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: fix phy interrupt settingChristian Lamparter2019-03-132-2/+2
| | | | | | | | | | | | | This patch fixes a problem that was discovered during DSA development. On the MR33, the link change events from the external AR8035-PHY would never make it to the qca8k driver. The issue turned out to be a misplaced memcpy that was copying over the zero-initialized irq table, when it should have been set to PHY_POLL. Hence this patch moves the memcpy after the array has been initialized. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: tidy up 02_networksChristian Lamparter2019-03-131-2/+2
| | | | | | | | - fix linksys' EA6350v3 order - remove whitespace that should have been tabs Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: backport I2C QUP driver changes from 4.17Piotr Dymacz2019-03-0813-0/+2781
| | | | | | | | | | | | | | | | | | | | | | | | Backport below changes for I2C QUP driver from v4.17: 0668bc44a426 i2c: qup: fix copyrights and update to SPDX identifier 7239872fb340 i2c: qup: fixed releasing dma without flush operation completion eb422b539c1f i2c: qup: minor code reorganization for use_dma 6d5f37f166bb i2c: qup: remove redundant variables for BAM SG count c5adc0fa63a9 i2c: qup: schedule EOT and FLUSH tags at the end of transfer 7e6c35fe602d i2c: qup: fix the transfer length for BAM RX EOT FLUSH tags 3f450d3eea14 i2c: qup: proper error handling for i2c error in BAM mode 08f15963bc75 i2c: qup: use the complete transfer length to choose DMA mode ecb6e1e5f435 i2c: qup: change completion timeout according to transfer length 6f2f0f6465ac i2c: qup: fix buffer overflow for multiple msg of maximum xfer len f7714b4e451b i2c: qup: send NACK for last read sub transfers fbfab1ab0658 i2c: qup: reorganization of driver code to remove polling for qup v1 7545c7dba169 i2c: qup: reorganization of driver code to remove polling for qup v2 This fixes various I2C issues observed on AP120C-AC board equipped with Atmel/Microchip AT97SC3205T TPM module. Tested-by: Christian Lamparter <chunkeey@gmail.com> Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add ath10k-calibration-variant in AP120C-AC DTSPiotr Dymacz2019-03-082-0/+2
| | | | | | | | Use 'ath10k-calibration-variant' (with the value sent upstream) for the second (5 GHz) radio in AP120C-AC board DTS. First radio uses the same BDF as in one of Qualcomm reference designs. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: bump 4.14 to 4.14.104Koen Vandeputte2019-03-051-3/+0
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 332-arc-add-OWRTDTB-section.patch Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: add support for FritzBox 7530David Bauer2019-02-289-5/+634
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4019 RAM: 256M FLASH: 128M NAND ETH: QCA8075 VDSL: Intel/Lantiq VRX518 PCIe attached currently not supported DECT: Dialog SC14448 currently not supported WiFi2: IPQ4019 2T2R 2SS b/g/n WiFi5: IPQ4019 2T2R 2SS n/ac LED: - Power/DSL green - WLAN green - FON/DECT green - Connect/WPS green - Info green - Info red BTN: - WLAN - FON - WPS/Connect UART: 115200n8 3.3V (located under the Dialog chip) VCC - RX - TX - GND (Square is VCC) Installation ------------ 1. Grab the uboot for the Device from the 'u-boot-fritz7530' subdirectory. Place it in the same directory as the 'eva_ramboot.py' script. It is located in the 'scripts/flashing' subdirectory of the OpenWRT tree. 2. Assign yourself the IP address 192.168.178.10/24. Connect your Computer to one of the boxes LAN ports. 3. Connect Power to the Box. As soon as the LAN port of your computer shows link, load the U-Boot to the box using following command. > ./eva_ramboot.py --offset 0x85000000 192.168.178.1 uboot-fritz7530.bin 4. The U-Boot will now start. Now assign yourself the IP address 192.168.1.70/24. Copy the OpenWRT initramfs (!) image to a TFTP server root directory and rename it to 'FRITZ7530.bin'. 5. The Box will now boot OpenWRT from RAM. This can take up to two minutes. 6. Copy the U-Boot and the OpenWRT sysupgrade (!) image to the Box using scp. SSH into the Box and first write the Bootloader to both previous kernel partitions. > mtd write /path/to/uboot-fritz7530.bin uboot0 > mtd write /path/to/uboot-fritz7530.bin uboot1 7. Remove the AVM filesystem partitions to make room for our kernel + rootfs + overlayfs. > ubirmvol /dev/ubi0 --name=avm_filesys_0 > ubirmvol /dev/ubi0 --name=avm_filesys_1 8. Flash OpenWRT peristently using sysupgrade. > sysupgrade -n /path/to/openwrt-sysupgrade.bin Signed-off-by: David Bauer <mail@david-bauer.net> [removed pcie-dts range node, refreshed on top of AP120-AC/E2600AC] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix pcie msi IRQ trigger levelChristian Lamparter2019-02-282-0/+64
| | | | | | | | | | | | | | | | | | From: Niklas Cassel <niklas.cassel@linaro.org> |The databook clearly states that the MSI IRQ (msi_ctrl_int) is a level |triggered interrupt. | |The msi_ctrl_int will be high for as long as any MSI status bit is set, |thus the IRQ type should be set to IRQ_TYPE_LEVEL_HIGH, causing the |IRQ handler to keep getting called, as long as any MSI status bit is set. |[...] |Not having the correct IRQ type defined will cause us to lose interrupts, |which in turn causes timeouts in the PCIe endpoint drivers. | |Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org> |Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: enlarge PCIe BAR sizeChristian Lamparter2019-02-282-0/+87
| | | | | | | | | | | | | | | | | | | | | | | | | | David Bauer reported that the VDSL modem (attached via PCIe) on his AVM Fritz!Box 7530 was complaining about not having enough space in the BAR. A closer inspection of the old qcom-ipq40xx.dtsi pulled from the GL-iNet repository listed: | qcom,pcie@80000 { | compatible = "qcom,msm_pcie"; | reg = <0x80000 0x2000>, | <0x99000 0x800>, | <0x40000000 0xf1d>, | <0x40000f20 0xa8>, | <0x40100000 0x1000>, | <0x40200000 0x100000>, | <0x40300000 0xd00000>; | reg-names = "parf", "phy", "dm_core", "elbi", | "conf", "io", "bars"; Matching the reg-names with the listed reg leads to <0xd00000> as the size for the "bars". BugLink: https://www.mail-archive.com/openwrt-devel@lists.openwrt.org/msg45212.html Reported-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Qxwlan E2600AC C1 and C2张鹏2019-02-2813-15/+978
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Qxwlan E2600AC C1 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB FLASH: 32 MiB Winbond W25Q256 ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power ,6 driven by gpio SERIAL: UART (J5) UUSB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "sysupgrade" filename to "firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "sysupgrade" image and click the upgrade button. Qxwlan E2600AC C2 based on IPQ4019 Specifications: SOC: Qualcomm IPQ4019 DRAM: 256 MiB NOR: 16 MiB Winbond W25Q128 NAND: 128MiB Micron MT29F1G08ABAEAWP ETH: Qualcomm QCA8075 WLAN: 5G + 5G/2.4G * 2T2R 2.4/5 GHz - QCA4019 hw1.0 (SoC) * 2T2R 5 GHz - QCA4019 hw1.0 (SoC) INPUT: Reset buutton LED: 1x Power, 6 driven by gpio SERIAL: UART (J5) USB: USB3.0 POWER: 1x DC jack for main power input (9-24 V) SLOT: Pcie (J25), sim card (J11), SD card (J51) Flash instruction (using U-Boot CLI and tftp server): - Configure PC with static IP 192.168.1.10 and tftp server. - Rename "ubi" filename to "ubi-firmware.bin" and place it in tftp server directory. - Connect PC with one of RJ45 ports, power up the board and press "enter" key to access U-Boot CLI. - Use the following command to update the device to OpenWrt: "run lfw". Flash instruction (using U-Boot web-based recovery): - Configure PC with static IP 192.168.1.xxx(2-254)/24. - Connect PC with one of RJ45 ports, press the reset button, power up the board and keep button pressed for around 6-7 seconds, until LEDs start flashing. - Open your browser and enter 192.168.1.1, select "ubi" image and click the upgrade button. Signed-off-by: 张鹏 <sd20@qxwlan.com> [ added rng node. whitespace fixes, ported 02_network, ipq-wifi Makefile, misc dts fixes, trivial message changes ] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ALFA Network AP120C-ACPiotr Dymacz2019-02-2610-4/+742
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ALFA Network AP120C-AC is a dual-band ceiling AP, based on Qualcomm IPQ4018 + QCA8075 platform. Specification: - Qualcomm IPQ4018 (717 MHz) - 256 MB of RAM (DDR3) - 16 MB (SPI NOR) + 128 MB (SPI NAND) of flash - 2x Gbps Ethernet, with 802.3af PoE support in one port - 2T2R 2.4/5 GHz (IPQ4018), with ext. FEMs (QFE1952, QFE1922) - 3x U.FL connectors - 1x 1.8 dBi (Bluetooth) and 2x 3/5 dBi dual-band (Wi-Fi) antennas - Atmel/Microchip AT97SC3205T TPM module (I2C bus) - TI CC2540 Bluetooth LE module (USB 2.0 bus) - 4x LED (all driven by GPIO) - 1x button (reset) - 1x USB 2.0 (optional, not installed in indoor version) - DC jack for main power input (12 V) - UART header available on PCB (2.0 mm pitch) Flash instruction: 1. This board uses dual-image feature (128 MB NAND is divided into two 64 MB partitions: 'rootfs1' and 'rootfs2'). 2. Before update, make sure your device is running firmware no older than v1.1 (previous versions have incompatible U-Boot). 3. Use 'factory' image in vendor GUI or for sysupgrade tool, without preserving settings. Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* ipq40xx: add support for Macronix MX35LF1GE4AB SPI NANDPiotr Dymacz2019-02-261-0/+13
| | | | | | | | | | Without a proper SPI NAND support (SPI NAND framework is available in kernel >= 4.19) the only way to make such flash working is to include it in raw/parallel NAND subsystem support and combine with mt29f staging driver. Obviously, this approach isn't going to be accepted by upstream (similar support for Winbond W25N01GV was rejected). Signed-off-by: Piotr Dymacz <pepe2k@gmail.com>
* kernel: bump 4.14 to 4.14.102Koen Vandeputte2019-02-221-32/+0
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch Remove upstreamed hunks: - 080-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch Fixes: - CVE-2018-1000026 Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: speed up ath10k-caldata extractionChristian Lamparter2019-02-201-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Reading and writing to and from flash storage is slow and currently, the ath10kcal_extract() scripts are even more at an disadvantage because they use a block size of 1 to be able skip. This patch reworks the extraction scripts to be much faster and efficient by reading and writing the calibration data in possibly one big block. before: (Tested on a RT-AC58U, which has SPI-NAND). # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=1 skip=4096 count=12064 12064+0 records in 12064+0 records out real 0m 0.28s user 0m 0.02s sys 0m 0.24s after: # time dd if=/dev/ubi0_1 of=/lib/firmware/... bs=12064 skip=4096 count=1 iflag=skip_bytes 1+0 records in 1+0 records out real 0m 0.01s user 0m 0.00s sys 0m 0.00s Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix ipq40xx_setup_macs for Linksys EA6350v3Oever González2019-02-141-1/+1
| | | | | | | | | | | | | This commit fixes the script that sets the MAC address of the LAN switch. The LAN MAC address should be the WAN MAC address plus one. Without this patch the WAN and the LAN interface will use the same MAC address and an error will be generated. With this patch all interfaces will have a different MAC address, consecutive in the following order: WAN, LAN, radio0 and radio1. Signed-off-by: Oever González <notengobattery@gmail.com>
* ipq40xx: add support for ASUS LyraMarius Genheimer2019-02-1410-6/+652
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SoC: Qualcomm IPQ4019 (Dakota) 717 MHz, 4 cores RAM: 256 MiB (Nanya NT5CC128M16IP-DI) FLASH: 128 MiB (Macronix NAND) WiFi0: Qualcomm IPQ4019 b/g/n 2x2 WiFi1: Qualcomm IPQ4019 a/n/ac 2x2 WiFi2: Qualcomm Atheros QCA9886 a/n/ac BT: Atheros AR3012 IN: WPS Button, Reset Button OUT: RGB-LED via TI LP5523 9-channel Controller UART: Front of Device - 115200 N-8 Pinout 3.3v - RX - TX - GND (Square is VCC) Installation: 1. Transfer OpenWRT-initramfs image to the device via SSH to /tmp. Login credentials are identical to the Web UI. 2. Login to the device via SSH. 3. Flash the initramfs image using > mtd-write -d linux -i openwrt-image-file 4. Power-cycle the device and wait for OpenWRT to boot. 5. From there flash the OpenWRT-sysupgrade image. Ethernet-Ports: Although labeled identically, the port next to the power socket is the LAN port and the other one is WAN. This is the same behavior as in the stock firmware. Signed-off-by: Marius Genheimer <mail@f0wl.cc> [Dropped setup_mac 02_network in favour of 05_set_iface_mac_ipq40xx.sh, reorderd 02_network entries, added board.bin WA for the QCA9886 from ath79, minor dts touchup, added rng to 4.19 dts] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: ea6350v3: 4.19: enable pseudo rng supportChristian Lamparter2019-02-141-0/+4
| | | | | | | Robert Marko made a big effort to enable the rng on all ipq40xx for 4.19, so let's continue the quest. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix ASUS RT-AC58U switch port numberingChristian Lamparter2019-02-051-5/+5
| | | | | | | | This patch fixes the ASUS' RT-AC58U port order by unifying the configuration with the NBG6617. Reported-by: Roberto Socrates (rtac58u-user on the forum) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: consolidate 02_network board defaultsChristian Lamparter2019-02-051-58/+66
| | | | | | | | This patch splits the big board case switch in 02_network in two functions ipq40xx_setup_interfaces() and ipq40xx_setup_macs() just like ath79 and ramips do. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for Linksys EA6350v3Oever González2019-01-2610-2/+734
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 RAM: 256 MiB Samsung K4B2G1646F-BYK0 FLASH1: MX25L1605D 2 MB FLASH2: Winbond W25N01GV 128Mb ETH: Qualcomm QCA8075 WLAN0: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN1: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Reset LED: Status - Green SERIAL: Header at J19, Beneath DC Power Jack 1-VCC ; 2-TX ; 3-RX; 4-GND; Serial 115200-8-N-1. Tested and working: - USB (requires extra packages) - LAN Ethernet (Correct MAC-address) - WAN Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from Web UI - OpenWRT sysupgrade - LED - Reset Button Need Testing: - WPS button Install via Web UI: - Attach to a LAN port on the router. - Connect to the Linksys Smart WiFi Page (default 192.168.1.1) and login - Select the connectivity tab on the left - In the manual update box on the right - Select browse, and browse to openwrt-ipq40xx-linksys_ea6350v3-squashfs-factory.bin - Click update. - Read and accept the warning - The router LED will start blinking. When the router LED goes solid, you can now navigate to 192.168.1.1 to your new OpenWrt installation. Sysupgrade: - Flash the sysupgrade image as usual. Please: try to do a reset everytime you can (doing it with LuCI is easy and can be done in the same step). Recovery (Automatic): - If the device fails to boot after install or upgrade, whilst the unit is turned on: 1 - Wait 15 seconds 2 - Switch Off and Wait 10 seconds 3 - Switch on 4 - Repeat steps 1 to 3, 3 times then go to 5. 5 - U-boot will have now erased the failed update and switched back to the last working firmware - you should be able to access your router on LAN. Recovery (Manual): - The steps for manual recovery are the same as the generic u-boot tftp client method. Back To Stock: - Use the generic recovery using the tftp client method to flash the "civic.img". Also you can strip-and-pad the original image and use the generic "mtd" method by flashing over the "kernel" partition. * Just be careful to flash in the partition that the device is currently booted. Signed-off-by: Ryan Pannell <ryan@osukl.com> Signed-off-by: Oever González <notengobattery@gmail.com> [minor edits, removed second compatible of nand, added dtb entry to 4.19] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: 4.19: fix pcie wifi unit-address of the MR33 and A62Christian Lamparter2019-01-262-2/+2
| | | | | | | | The unit address should be wifi@1,0 since the device is located at 0000:01:00.0. Reported-by: Sven Eckelmann <sven@narfation.org> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: remove misplaced MR33 UCI definitionDavid Bauer2019-01-261-3/+0
| | | | | | | | | | | This removes the misplaced UCI-network configuration for the MR33. The LAN port is set in 01_leds while it is already correctly defined in 02_network. This was most likely an oversight as no network configuration belongs into 01_leds. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: dts: Unify naming of gpio-led nodesPetr Štetiar2019-01-2415-15/+15
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* ipq40xx: dts: Unify naming of gpio-keys nodesPetr Štetiar2019-01-2415-15/+15
| | | | | | | | | | | | | | In DTS Checklist[1] we're now demanding proper generic node names, as the name of a node should reflect the function of the device and use generic name for that[2]. Everybody seems to be copy&pasting from DTS files available in the repository today, so let's unify that naming there as well and provide proper examples. 1. https://openwrt.org/submitting-patches#dts_checklist 2. https://github.com/devicetree-org/devicetree-specification/blob/master/source/devicetree-basics.rst#generic-names-recommendation Signed-off-by: Petr Štetiar <ynezz@true.cz> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [split up]
* kernel: bump 4.19 to 4.19.16Stijn Tintel2019-01-171-5/+5
| | | | | | | | | | | | | | | | | Refresh patches. Remove upstreamed patches: - backport/096-mips-math-emu-Write-protect-delay-slot-emulation-pages.patch - backport/096-v4.20-netfilter-ipv6-Preserve-link-scope-traffic-original-.patch - backport/424-v4.20-net-dsa-fix-88e6060-roaming.patch - hack/100-mtd-rawnand-qcom-fix-memory-corruption-that-causes-p.patch - pending/510-f2fs-fix-sanity_check_raw_super-on-big-endian-machines.patch Update patch that no longer applies: - backport/343-netfilter-nft_flow_offload-handle-netdevice-events-f.patch Compile-tested: mesongx Runtime-tested: mesongx Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.14 to 4.14.91Koen Vandeputte2019-01-071-5/+5
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 500-ubifs-Handle-re-linking-of-inodes-correctly-while-re.patch Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGEDavid Bauer2019-01-061-2/+2
| | | | | | | | | | | | Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: 4.14: Sync kernel configRobert Marko2019-01-051-0/+2
| | | | | | | | This patch syncs the 4.14 kernel config to the current generic configuration. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ipq40xx: 4.19: Sync kernel configRobert Marko2019-01-051-7/+0
| | | | | | | | | This patch syncs the 4.19 kernel config since the KERNEL_STACKPROTECTOR and compiler options are now part of the 4.19 generic config. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> [reworded commit]
* ipq40xx: fix 4.14 ImageBuilder build woesChristian Lamparter2019-01-051-2/+2
| | | | | | | | | | | | | | | | | | | | | | Robert Marko reported an issue with the current imagebuilder images: "Imagebuilder includes the new kmod-usb-dwc3-qcom USB driver package by default even on 4.14. [...] the current state imagebuilder can't build images under 4.14 at all as the kmod-usb-dwc3-qcom does not exist in it so it throws and error and exits." This patch reverts the Makefile to just kmod-usb-dwc3-of-simple and once the switch to 4.19 is done. It also removes the kmod-usb-phy-qcom-dwc3 as they only contain the usb-phy drivers for the ipq806x generation. Dynamic switching based on the KERNEL_PATCHVER is possible by using: $(if $(filter 4.14,$(KERNEL_PATCHVER)),kmod-usb-dwc3-of-simple,kmod-usb-dwc3-qcom) though it Fixes: 13321fa1429 ("ipq40xx: Use kmod-usb-dwc3-qcom by default") Fixes: 6e58fb2c33e ("ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcom") Reported-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: convert to device-tree based USB LED triggerChristian Lamparter2018-12-275-2/+108
| | | | | | | | Thanks to the ledtrig-usb.c the USB LED trigger can be setup in the device-tree definition for the Asus RT-AC58U and ZyXEL NBG6617. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix warning triggered by bad interrupt definitionChristian Lamparter2018-12-272-4/+4
| | | | | | | | | | | | | | | | | | | | | | | This patch fixes a kernel warning that got triggered by 4.19 because of a bad/missing interrupt level definition in the DTS. | WARNING: CPU: 2 PID: 1996 at drivers/irqchip/irq-gic.c:1016 | CPU: 2 PID: 1996 Comm: kmodloader Not tainted 4.19.9 #0 | Hardware name: Generic DT based system | [<c0317884>] (warn_slowpath_null) from [<c04f9cd0>] | [<c04f9cd0>] (gic_irq_domain_translate) from [<c035af30>] | [<c035af30>] (irq_create_fwspec_mapping) from [<c035b1e0>] | [<c035b1e0>] (irq_create_of_mapping) from [<c0614eec>] | [<c0614eec>] (of_irq_get) from [<c0614f3c>] | [<c0614f3c>] (of_irq_to_resource) from [<c0614ff0>] | [<c0614ff0>] (of_irq_to_resource_table) from [<c0610e08>] | [<c0610e08>] (of_device_alloc) from [<c0610ea0>] | [<c0610ea0>] (of_platform_device_create_pdata) | [<c061120c>] (of_platform_bus_create) | [<c06113c4>] (of_platform_populate) | [<bf4c06b4>] (dwc3_qcom_probe [dwc3_qcom]) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: kmod-usb-dwc3-of-simple vs kmod-usb-dwc3-qcomChristian Lamparter2018-12-271-0/+1
| | | | | | | | | | | | | | | | | | | | | Robert Marko <robimarko@gmail.com> noted in "ipq40xx: Use kmod-usb-dwc3-qcom by default": | Since 4.18 we cant use DWC3 OF Simple anymore so we | have to use kmod-usb-dwc3-qcom. This patch adds a TODO right next to the KERNEL_PATCHVER so it will be picked up when moving to 4.19. I would also like to point out: All users/devs that are compiling their own images from source and have a existing 4.14 config and want to switch to 4.19: Please drop kmod-usb-dwc3-of-simple and add kmod-usb-dwc3-qcom module package. Otherwise, the USB port on your router will no longer work. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: MR33: device-tree updateChristian Lamparter2018-12-271-29/+31
| | | | | | | | | | | | | | - 4.19 no longer refuses to initialize the mdio bus if a phy is not connected. - fix partition unit-address - restrict partition offset and size to 32-bit integers. - add note to warn people not to mess with the ubi partition size. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: remove qcom,ipq4019 on all devicesChristian Lamparter2018-12-2714-14/+14
| | | | | | | | | | Upstream commit: 80483c3abf8 ("ARM: qcom: Cleanup/Remove unnecessary board file") removed all the platform device compatibles stating that: "This patch removes the unnecessary board file. The generic machine definition is sufficient for the Qualcomm platforms." Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: rt-ac58u: fix device-tree snafuChristian Lamparter2018-12-271-22/+27
| | | | | | | | | | | | | | | | | | | - make the device userspace integration (WIFI,MAC,sysupgrade) work again by renaming the ubi to UBI_DEV as a temporary measure. In the future, once 4.14 support is dropped, this can all be refactored again. *sigh* - use the wifi0 and wifi1 labels - follow Device-Tree Release v0.2 2.2.2 Generic Names Recommendation - fix duplicated partition node-names - remove qcom,ipq4019 platform compatible. it's no longer needed (and wrong because the chip is a qcom,ipq4018). Fixes: 4c67f3ad78d ("ipq40xx: Adapt 4.19 DTS for upstream SPI-NAND driver") Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: 4.19: Enable pseudo random number generatorRobert Marko2018-12-2714-1/+53
| | | | | | | | IPQ40xx series has a HW pseudo random number generator built in. It already has a node in the upstream ipq4019.dtsi so we just need to enable it. Its driver has been rewritten to use crypto API so we dont have char interface like under 4.14 kernel. Signed-off-by: Robert Marko <robimarko@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-03 19:48:10 +0000