aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* kernel: Update kernel 4.14 to version 4.14.195Hauke Mehrtens2020-08-274-19/+19
| | | | | | Compile and runtime tested on x86/64. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: Update kernel 4.14 to version 4.14.187Hauke Mehrtens2020-07-051-1/+1
| | | | | | | | | | Fixes: - CVE-2020-10757 Run tested: x86 Build tested: x86 Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: essedma: Disable TCP segmentation offload for IPv6Sven Eckelmann2020-06-131-0/+46
| | | | | | | | | | | | | | | | | | | | | | | | | | | It was noticed that the the whole MAC can hang when transferring data from one ar40xx port (WAN ports) to the CPU and from the CPU back to another ar40xx port (LAN ports). The CPU was doing only NATing in that process. Usually, the problem first starts with a simple data corruption: $ wget https://cdimage.debian.org/debian-cd/current/amd64/iso-cd/debian-10.4.0-amd64-netinst.iso -O /dev/null ... Connecting to saimei.ftp.acc.umu.se (saimei.ftp.acc.umu.se)|2001:6b0:19::138|:443... connected. ... Read error at byte 48807936/352321536 (Decryption has failed.). Retrying. But after a short while, the whole MAC will stop to react. No traffic can be transported anymore from the CPU port from/to the AR40xx PHY/switch and the MAC has to be resetted. The whole problem can be avoided by disabling the TSO for IPv6 for this ethernet MAC driver. Signed-off-by: Sven Eckelmann <sven@narfation.org> Acked-by: John Crispin <john@phrozen.org> (backported from commit 678569505623e50bbbbc344c7e820fb315b79ede, with updated commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.172Koen Vandeputte2020-03-091-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: fix build errorKoen Vandeputte2019-11-201-11/+10
| | | | | | | Add missing brace which was accidentally omitted Fixes: 6d6026021390 ("kernel: bump 4.14 to 4.14.154") Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.154Koen Vandeputte2019-11-191-16/+31
| | | | | | | | | | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 902-debloat_proc.patch - 040-dmaengine-qcom-bam-Process-multiple-pending-descript.patch Remove upstreamed: - 303-spi-nor-enable-4B-opcodes-for-mx66l51235l.patch New symbols: X86_INTEL_MPX X86_INTEL_MEMORY_PROTECTION_KEYS X86_INTEL_TSX_MODE_OFF X86_INTEL_TSX_MODE_ON X86_INTEL_TSX_MODE_AUTO SGL_ALLOC Compile-tested on: cns3xxx Runtime-tested on: cns3xxx Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: copy Fritz4040 UBoot to STAGING_DIR_IMAGEDavid Bauer2019-03-181-2/+2
| | | | | | | | | | | | | Copy U-Boot to STAGING_DIR_IMAGE (and append it to the EVA-image from there) to fix image generation using the image-builder. Also remove the bootloader from DEVICE_PACKAGES and instead use the BUILD_DEVICES directive from within the U-Boot makefile. This fixes eva-image generation using the OpenWRT image-builder. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 634c733065256979835ca3d7218ae8203a693683)
* kernel: bump 4.14 to 4.14.102Koen Vandeputte2019-02-251-32/+0
| | | | | | | | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 272-uapi-if_ether.h-prevent-redefinition-of-struct-ethhd.patch Remove upstreamed hunks: - 105-pinctrl-msm-fix-gpio-hog-related-boot-issues.patch Fixes: - CVE-2018-1000026 Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.89Koen Vandeputte2018-12-181-3/+3
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.86Koen Vandeputte2018-12-131-1/+1
| | | | | | | | | | | | Refreshed all patches. Altered patches: - 180-usb-xhci-add-support-for-performing-fake-doorbell.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: fix openmesh sysupgrade with tar content out of orderMarek Lindner2018-12-051-3/+3
| | | | | | | | | | | | The tar extraction depends on the order in which the files are added to the tar file. Since the order is not guaranteed and depends on the host system, the combined mtd write fails with sysupgrade images built on some systems. Fix by changing to tar file order independent mtd write. Fixes: 86e18f6706e1 ("ipq806x: add support for OpenMesh A42") Signed-off-by: Marek Lindner <mareklindner@neomailbox.ch> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* kernel: bump 4.14 to 4.14.79Koen Vandeputte2018-11-051-1/+1
| | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.77Koen Vandeputte2018-10-191-0/+1
| | | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch New symbol for arm targets: - HARDEN_BRANCH_PREDICTOR Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Stijn Tintel <stijn@linux-ipv6.be>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-261-1/+1
| | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.67Koen Vandeputte2018-08-281-1/+1
| | | | | | | | | | | | Refreshed all patches. Removed upstreamed patches: - 037-v4.18-0008-ARM-dts-BCM5301x-Fix-i2c-controller-interrupt-type.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump kernel 4.14 to version 4.14.63Hauke Mehrtens2018-08-152-27/+1
| | | | | | | | | | | | | | The following patches were integrated upstream: * target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch * target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* ipq40xx: add get_status_led to diag.shDavid Bauer2018-07-151-0/+4
| | | | | | | | | | | | This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 4fc005197a320ff728544eba8028f7a9f23e1868)
* kernel: bump 4.14 to 4.14.54 for 18.06Koen Vandeputte2018-07-121-1/+1
| | | | | | | | | | | | Refreshed all patches Reworked patches to match upstream: 335-v4.16-netfilter-nf_tables-add-single-table-list-for-all-fa.patch Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.52 for 18.06Stijn Segers2018-07-022-8/+3
| | | | | | | Compile-tested on: ramips/mt7621, x86/64. Run-tested on: ramips/mt7621. Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-217-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com> (cherry picked from commit 4b280ad91a6b155ac71c417aaa7bb5f4e328712f)
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com> (cherry picked from commit 8f804f42d52e49191429ad1d716e7adb3cd10ceb)
* kernel: bump 4.14 to 4.14.48 for 18.06Stijn Segers2018-06-071-11/+11
| | | | | | | | | | | | | | Refreshed patches. The following patches were upstreamed and have been deleted: * target/linux/lantiq/patches-4.14/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch * target/linux/generic/pending-4.14/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch * target/linux/generic/pending-4.14/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch * target/linux/generic/pending-4.14/181-net-usb-add-lte-modem-wistron-neweb-d18q1.patch Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621 Signed-off-by: Stijn Segers <foss@volatilesystems.org>
* ipq40xx: add eva-image for FRITZ!Box 4040David Bauer2018-05-241-1/+4
| | | | | | | | | | This commit adds an EVA flashable image for the FRITZ!Box 4040. The image contains the U-Boot with OpenWRT appended to it. This way we remove the need to use UART for initial flashing. Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 70e6ea319d3bfdfdb34be540dc7d89aa175b5587)
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit 67a3cdcbb05559549985a189eabaf2df92559ed7)
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit bdc2b58c4bccb50242af853dc80b50f9324b841c)
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit a08b0d0c3149060f1585ad3ea2ea3edfde71bce4)
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit 978543a246c6badb5e5e1c2430211e01f005af27)
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-241-2/+0
| | | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit ead26e9db649a508ba93e7e8193ada70322620b1)
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-241-1/+0
| | | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com> (cherry picked from commit f928c338ad6c8215a5fe280473e37786157a2d05)
* ipq40xx: fix ethernet on ap-dk01.1Roman Yeryomin2018-05-241-0/+25
| | | | | | | | Not sure how it worked before but ethernet is disabled by default in ipq4019 dtsi. Signed-off-by: Roman Yeryomin <roman@advem.lv> (cherry picked from commit 1f42deec8edac3e99f83f7343cbd4fec29333345)
* kernel: bump 4.14 to 4.14.36Koen Vandeputte2018-04-261-1/+1
| | | | | | | | | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Fixes for CVEs: CVE-2018-1108 CVE-2018-1092 CVE-2018-1094 CVE-2018-1095 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Stijn Segers <foss@volatilesystems.org>
* ipq40xx: add support for OpenMesh A62Sven Eckelmann2018-04-237-5/+276
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | * QCA IPQ4019 * 256 MB of RAM * 32 MB of SPI NOR flash (s25fl256s1) - 2x 15 MB available; but one of the 15 MB regions is the recovery image * 2T2R 2.4 GHz - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=20,variant=OM-A62 * 2T2R 5 GHz (channel 36-64) - QCA9888 hw2.0 (PCI) - requires special BDF in QCA9888/hw2.0/board-2.bin bus=pci,bmi-chip-id=0,bmi-board-id=16,variant=OM-A62 * 2T2R 5 GHz (channel 100-165) - QCA4019 hw1.0 (SoC) - requires special BDF in QCA4019/hw1.0/board-2.bin with bus=ahb,bmi-chip-id=0,bmi-board-id=21,variant=OM-A62 * multi-color LED (controlled via red/green/blue GPIOs) * 1x button (reset; kmod-input-gpio-keys compatible) * external watchdog - triggered GPIO * 1x USB (xHCI) * TTL pins are on board (arrow points to VCC, then follows: GND, TX, RX) * 2x gigabit ethernet - phy@mdio3: + Label: Ethernet 1 + gmac0 (ethaddr) in original firmware + 802.3at POE+ - phy@mdio4: + Label: Ethernet 2 + gmac1 (eth1addr) in original firmware + 18-24V passive POE (mode B) * powered only via POE The tool ap51-flash (https://github.com/ap51-flash/ap51-flash) should be used to transfer the factory image to the u-boot when the device boots up. The initramfs image can be started using setenv bootargs 'loglevel=8 earlycon=msm_serial_dm,0x78af000 console=ttyMSM0,115200 mtdparts=spi0.0:256k(0:SBL1),128k(0:MIBIB),384k(0:QSEE),64k(0:CDT),64k(0:DDRPARAMS),64k(0:APPSBLENV),512k(0:APPSBL),64k(0:ART),64k(0:custom),64k(0:KEYS),15552k(inactive),15552k(inactive2)' tftpboot 0x84000000 openwrt-ipq40xx-openmesh_a62-initramfs-fit-uImage.itb set fdt_high 0x85000000 bootm 0x84000000 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: fix gpio-hog related boot issuesSven Eckelmann2018-04-236-6/+109
| | | | | | | | | | | | | | | The pinctrl initialization fails with the MSM pinctrl code and gpio-hogs because either the gpio ranges are not yet initialized (missing gpio-range in DT) or that the msm driver unconditionally tries to re-initializes the ranges (gpio-range in DT). To allow gpio-hogs and similar early-boot gpio code, the gpio-ranges must be in the device tree and the pinctrl-msm code must check whether the range was already initialized by the DT. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com> [drop changes to unrelated dtsi files, refresh patches] Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: use upstream board-2.binSven Eckelmann2018-04-235-10/+11
| | | | | | | The BDFs for all boards were upstreamed to the ath10k-firmware repository and are now part of ath10k-firmware 2018-04-19. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: ex61x0v2: Disable unused GMACsThomas Hebb2018-04-201-0/+1
| | | | | | | These devices have only one ethernet port. It doesn't make sense to expose the unused GMACs as separate network devices. Signed-off-by: Thomas Hebb <tommyhebb@gmail.com>
* ipq40xx: Move reserved-memory DT to qcom-ipq4019.dtsiSven Eckelmann2018-04-2010-145/+89
| | | | | | | | The tz and smem reserved-memory information handled in the upstream Linux sources by the SoC specific dtsi and not by the the boards dts. Using the same approach in OpenWrt avoids unneccessary duplication. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Remove unused reserved-memory nodesSven Eckelmann2018-04-207-76/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The reserved-memory regions are mostly undocumented by QCA and are named very unspecific in the QSDK device trees. It was tried to clean them up by commit 71ed9f10a33e ("ipq40xx: Use detailed reserved memory for A42") and similar changes. The features which require these regions were mostly unknown but Senthilkumar N L <snlakshm@qti.qualcomm.com> and Sricharan Ramabadhran <srichara@qti.qualcomm.com> provided some more insight in some of them: * crash dump feature - a couple of regions used when 'qca,scm_restart_reason' dt node has the value 'dload_status' not set to 1 + apps_bl <0x87000000 0x400000> + sbl <0x87400000 0x100000> + cnss_debug <0x87400000 0x100000> + cpu_context_dump <0x87b00000 0x080000> - required driver not available in Linux - safe to remove * QSEE app execution - region tz_apps <0x87b80000 0x280000> - required driver not available in Linux - safe to remove * communication with TZ/QSEE - region smem <0x87b80000 0x280000> - driver changes not yet upstreamed - must not be removed because any access can crash kernel/program * trustzone (QSEE) private memory - region tz <0x87e80000 0x180000> - must not be removed because any access can crash kernel/program Removing the unnecessary regions saves some kilobyte of reserved-memory and cleans up the device tree: * 2560 KiB - 8devices Jalapeno - AVM FRITZ!Box 4040 - Compex WPJ428 - Meraki MR33 Access Point - OpenMesh A42 * 14336 KiB - GL.iNet GL-B1300 - Qualcomm Technologies, Inc. IPQ40xx/AP-DK01.1-C1 Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* build: consolidate fake uImage header build commandsMathias Kresin2018-04-201-2/+2
| | | | | | | | | | | Merge the two existing functions and use a parameter for the type header field. It updates the syntax of the former mpc85xx fake ramdisk header command to be compatible with mkimage from u-boot 2018.03 and fixes the build error spotted by the build bot. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump 4.14 to 4.14.34Stijn Tintel2018-04-161-1/+1
| | | | | | | | | | | | | Refresh patches. Update patches that no longer apply: - backport/313-netfilter-remove-defensive-check-on-malformed-packet.patch - pending/642-net-8021q-support-hardware-flow-table-offload.patch Compile-tested: x86/64. Runtime-tested: x86/64. Signed-off-by: Stefan Lippers-Hollmann <s.l-h@gmx.de> Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq40xx: unbundle firmware and board fileMathias Kresin2018-04-132-5/+5
| | | | | | | | | | | Don't select the firmware with the board file, it prevents an easy use of the -ct ath10k firmware. Select the firmware within the default packages instead. Remove the per device selection of the firmware now that it the firmware is selected by default. Signed-off-by: Mathias Kresin <dev@kresin.me>
* ipq40xx: add support for Netgear EX6100v2/EX6150v2David Bauer2018-04-139-3/+446
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MB Winbond W632GU6KB12J FLASH: 16 MiB Macronix MX25L12805D ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n/ac 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac 1x1 (EX6100) 2x2 (EX6150) INPUT: Power, WPS, reset button AP / Range-extender toggle LED: Power, Router, Extender (dual), WPS, Left-/Right-arrow SERIAL: Header next to QCA8072 chip. VCC, TX, RX, GND (Square hole is VCC) WARNING: The serial port needs a TTL/RS-232 v3.3 level converter! The Serial setting is 115200-8-N-1. Tested and working: - Ethernet - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from WebIF - Factory installation from tftp - OpenWRT sysupgrade (Preserving and non-preserving) - LEDs - Buttons Not Working: - AP/Extender toggle-switch Untested: - Support on EX6100v2. They share the same GPL-Code and vendor-images. The 6100v2 seems to lack one 5GHz stream and differs in the 5GHz board-blob. I only own a EX6150v2, therefore i am only able to verify functionality on this device. Install via Web-Interface: Upload the factory image to the device to the Netgear Web-Interface. The device might asks you to confirm the update a second time due to detecting the OpenWRT firmware as older. The device will automatically reboot after the image is written to flash. Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command "fw_recovery" will start a tftp server, waiting for a DNI image to be pushed. Assign your computer the IP-address 192.168.1.10/24. Push image with tftp -4 -v -m binary 192.168.1.1 -c put <OPENWRT_FACTORY> Device will erase factory-partition first, then writes the pushed image to flash and reboots. Parts of this commit are based on Thomas Hebb's work on the openwrt-devel mailinglist. See https://lists.openwrt.org/pipermail/openwrt-devel/2018-January/043418.html Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: Add 8devices JalapenoRobert Marko2018-04-131-1/+1
| | | | | | | Add custom board-2.bin for 8devices Jalapeno. Upstreaming is in progress. Signed-off-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: add support for 8devices JalapenoRobert Marko2018-04-136-9/+317
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for 8devices Jalapeno. Specification: QCA IPQ4018, Quad core ARM v7 Cortex A7 717MHz 256 MB of DDR3 RAM 8 MB of SPI NOR flash 128 MB of Winbond SPI NAND flash WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=16,variant=8devices-Jalapeno WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 requires special BDF in QCA4019/hw1.0/board-2.bin with: bus=ahb,bmi-chip-id=0,bmi-board-id=17,variant=8devices-Jalapeno ETH: Qualcomm Atheros QCA8072 Gigabit Switch (1 x LAN, 1 x WAN) phy@mdio3: Label: eth0 gmac0 phy@mdio4: Label: eth1 gmac1 Installation instructions: Since boards ship with old version of LEDE installation is simple. Just use sysupgrade -n -F sysupgrade.bin Syuspgrade needs to be forced since OpenWRT uses DT detection in recent releases. If you get error that FIT configuration is not found during boot it is due to older U-boot used on your board. That is because 8devices used custom FIT configuration partition name as they internally had v1 and v2 boards. Only v2 boards are sold so now they are shipping boards with never U-boot using generic config@1 FIT partition name. Also for old uboot it is possible to force loading config@1 by changing uboot environment: setenv boot5 'bootm 0x84000000#config@1’ saveenv Signed-off-by: Robert Marko <robimarko@gmail.com>
* Kernel: bump 4.14 to 4.14.29Stijn Segers2018-03-233-47/+47
| | | | | | | | | | | | Right patch version this time, sorry! * Patch 180-usb-xhci-add-support-for-performing-fake-doorbell.patch had to be adjusted slightly because of upstream adapted code. * Refreshed patches. Compile-tested: ramips/mt7621, x86/64 Run-tested: ramips/mt7621, x86/64 Signed-off-by: Stijn Segers <foss@volatilesystems.org> Tested-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: Add reserved memory for WPJ428Sven Eckelmann2018-03-231-0/+21
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The APPSBL and anything after that it not allowed to touch some of the memory regions which are used by other components. Still trying to write to the memory can lead to sudden device restarts (IPQ40xx) # mw 87e80000 0 data abort pc : [<873149f8>] lr : [<87308578>] sp : 86edfc28 ip : 86ef4412 fp : 00000000 r10: 00000000 r9 : 00000000 r8 : 86edff68 r7 : 00000003 r6 : 8737e624 r5 : 86ef4420 r4 : 8736c154 r3 : 00000000 r2 : 00000010 r1 : 00000000 r0 : 00000000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ... The device manufacturer only provided a very rough list of regions: * rsvd1: 0x87000000 0x500000 * wifi_dump: 0x87500000 0x600000 * rsvd2: 0x87b00000 0x500000 A more detailed list for devices using the AP.DK reference design memory maps was provided by Roman Yeryomin <roman@advem.lv> in commit 56f2df879fd ("ipq806x: ipq4019: add ap-dk01.1-c1 board support"): * apps_bl: 0x87000000 0x400000 * sbl: 0x87400000 0x100000 * cnss_debug: 0x87500000 0x600000 * cpu_context_dump: 0x87b00000 0x080000 * tz_apps: 0x87b80000 0x280000 * smem: 0x87e00000 0x080000 * tz: 0x87e80000 0x180000 The u-boot function ipq_fdt_mem_rsvd_fixup seems to suggest that only the rsvd2 (tz_apps, smem, tz) should be protected. All other regions would have been removed by it when CONFIG_QCA_APPSBL_DLOAD is not enabled. This allows to reduce the 16MB reserved memory region to only 4.5MB. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Use detailed reserved memory for A42Sven Eckelmann2018-03-231-6/+6
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The APPSBL and anything after that it not allowed to touch some of the memory regions which are used by other components. Still trying to write to the memory can lead to sudden device restarts (IPQ40xx) # mw 87e80000 0 data abort pc : [<873149f8>] lr : [<87308578>] sp : 86edfc28 ip : 86ef4412 fp : 00000000 r10: 00000000 r9 : 00000000 r8 : 86edff68 r7 : 00000003 r6 : 8737e624 r5 : 86ef4420 r4 : 8736c154 r3 : 00000000 r2 : 00000010 r1 : 00000000 r0 : 00000000 Flags: nZCv IRQs off FIQs off Mode SVC_32 Resetting CPU ... The device manufacturer only provided a very rough list of regions: * rsvd1: 0x87000000 0x500000 * wifi_dump: 0x87500000 0x600000 * rsvd2: 0x87b00000 0x500000 A more detailed list for devices using the AP.DK reference design memory maps was provided by Roman Yeryomin <roman@advem.lv> in commit 56f2df879fd ("ipq806x: ipq4019: add ap-dk01.1-c1 board support"): * apps_bl: 0x87000000 0x400000 * sbl: 0x87400000 0x100000 * cnss_debug: 0x87500000 0x600000 * cpu_context_dump: 0x87b00000 0x080000 * tz_apps: 0x87b80000 0x280000 * smem: 0x87e00000 0x080000 * tz: 0x87e80000 0x180000 The u-boot function ipq_fdt_mem_rsvd_fixup seems to suggest that only the rsvd2 (tz_apps, smem, tz) should be protected. All other regions would have been removed by it when CONFIG_QCA_APPSBL_DLOAD is not enabled. This allows to reduce the 16MB reserved memory region to only 4.5MB. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Remove phy reset gpio from Cisco Meraki MR33Sven Eckelmann2018-03-231-1/+0
| | | | | | | | There is currently no code to read the phy reset gpios for the ethernet PHY. It would also have been better to use the more common name "phy-reset-gpios" for this property. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Adjust SoC name of AVM Fritz!Box 4040Sven Eckelmann2018-03-233-2/+2
| | | | | | | The AVM Fritz!Box 4040 uses an IPQ4018 as SoC and not an IPQ4019. The DTS must be adjusted to reflect this. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Use constant to set gpio active low/highSven Eckelmann2018-03-237-8/+9
| | | | | | | | | The GPIO configuration in the DTS have as third parameter the active low/high configuration. This parameter is not easy to parse by humans when it is only set to 0/1. It is better to use the predefined constants GPIO_ACTIVE_HIGH and GPIO_ACTIVE_LOW. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: Fix DTS status parameter valuesSven Eckelmann2018-03-234-47/+47
| | | | | | | | The "Devicetree Specification, Release v0.2 - 2.3.4 status" [1] only allows the "okay" value for an operational device. The "ok" value will be accepted by the kernel but should be avoided. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-28 22:58:22 +0000