aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add support for EnGenius EAP1300Steven Lin2018-12-056-7/+261
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB NOR: 32 MiB ETH: Qualcomm Atheros QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button LEDS: Power, LAN, MESH, WLAN 2.4GHz, WLAN 5GHz 1. Load Ramdisk via U-Boot To set up the flash memory environment, do the following: a. As a preliminary step, ensure that the board console port is connected to the PC using these RS232 parameters: * 115200bps * 8N1 b. Confirm that the PC is connected to the board using one of the Ethernet ports. Set a static ip 192.168.99.8 for Ethernet that connects to board. The PC must have a TFTP server launched and listening on the interface to which the board is connected. At this stage power up the board and, after a few seconds, press 4 and then any key during the countdown. U-BOOT> set serverip 192.168.99.8 && set ipaddr 192.168.99.9 && tftpboot 0x84000000 openwrt.itb && bootm 2. Load image via GUI a. Upgrade EAP1300 to FW v3.5.3.2 In the GUI, System Manager > Firmware > Firmware Upgrade, to do upgrade. b. Transfer to OpenWrt from EnGenius. In Firmware Upgrade page, to upgrade yours openwrt-ipq40xx-engenius_eap1300-squashfs-sysupgrade.bin. 3. Revert to EnGenius EAP1300 To flash openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin by using sysupgrade command and "DO NOT" keep configuration. $ sysupgrade –n openwrt-ipq40xx-engenius_eap1300-squashfs-factory.bin Signed-off-by: Steven Lin <steven.lin@senao.com>
* kernel: bump 4.14 to 4.14.79Koen Vandeputte2018-11-051-5/+5
| | | | | | | | | Refreshed all patches. Compile-tested on: ar71xx, cns3xxx, imx6, x86_64 Runtime-tested on: ar71xx, cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: fix NBG6617 LED mappingDavid Bauer2018-11-051-3/+3
| | | | | | | | The NBG6617's LEDs are wrongly identified in the 01_leds boardinit script (board instead of boardname), resulting in referencing non-existent LEDs in UCI. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq-wifi: drop custom board-2.binsChristian Lamparter2018-11-011-2/+1
| | | | | | | | | | | | | The BDFs for all boards were upstreamed to the ath10k-firmware repository and linux-firmware.git. We switched to the upstream board-2.bin, hence the files can be removed here. Keep the ipq-wifi package in case new boards are added. It might take some time till board-2.bins send upstream are merged. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: nbg6617: switch to upstream boardfile variantChristian Lamparter2018-11-011-0/+2
| | | | | | | The NBG6617's boardfile was merged and this device can now switch to the upstream ath10k board-2.bin. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: rt-ac58u: replace ubi auto load hackChristian Lamparter2018-11-012-29/+4
| | | | | | | | | | | | This patch replaces the custom autoload quirk of the RT-AC58U with a bootargs-append overwrite. The vendor's u-boot doesn't leave the bootargs / cmdline alone, so the it can't be overwritten in any other way right now... And of course, this will be a lot of fun to deal with once the device switches to the new spi-nand subsystem. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.78Koen Vandeputte2018-10-221-4/+4
| | | | | | | | | | | | Refreshed all patches. Remove upstreamed: - 050-net-emac-fix-fixed-link-setup-for-the-RTL8363SB-swit.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.77Koen Vandeputte2018-10-191-0/+1
| | | | | | | | | | | | | | | Refreshed all patches. Altered patches: - 666-Add-support-for-MAP-E-FMRs-mesh-mode.patch New symbol for arm targets: - HARDEN_BRANCH_PREDICTOR Compile-tested on: ar71xx, cns3xxx, imx6 Runtime-tested on: ar71xx, cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* treewide: use wpad-basic for not small flash targetsMathias Kresin2018-10-161-1/+1
| | | | | | | | | | | | Add out of the box support for 802.11r and 802.11w to all targets not suffering from small flash. Signed-off-by: Mathias Kresin <dev@kresin.me> Mathias did all the heavy lifting on this, but I'm the one who should get shouted at for committing. Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk>
* ipq40xx: Create /var/lock directory in platform_do_upgrade_*Sven Eckelmann2018-10-071-8/+1
| | | | | | | | | | | | | | | | | | The sysupgrade_pre_upgrade hook was removed with 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") while there were still scripts using it: * target/linux/ar71xx/base-files/lib/upgrade/allnet.sh * target/linux/ar71xx/base-files/lib/upgrade/openmesh.sh * target/linux/ipq40xx/base-files/lib/upgrade/openmesh.sh Not running the hooks can either prevent a successful upgrade or brick the device because the fw_setenv program cannot be started correctly. Instead of adding this hook again, the directory /var/lock for fw_setenv can also just be created directly before fw_setenv is called. Fixes: 5e1b4c57ded7 ("base-files: drop fwtool_pre_upgrade") Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* mac80211: fix selecting of ath10k -ct firmwareHauke Mehrtens2018-09-271-1/+1
| | | | | | | There is not firmware file with -ct-ct postfix, remove one -ct. Fixes: 61b5b4971e7d ("mac80211: make ath10k-ct the default ath10k") Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* mac80211: make ath10k-ct the default ath10kJohn Crispin2018-09-262-4/+4
| | | | | | | | We select ath10k-ct by default, but it is still possible to build the upstream version. Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.14 to 4.14.72Koen Vandeputte2018-09-261-1/+1
| | | | | | | | | | | | | | | | | | | Refreshed all patches. Removed upstreamed: - 203-MIPS-ath79-fix-restart.patch - 0013-MIPS-ath79-fix-system-restart.patch - 180-earlycon-initialize-port-uartclk-based-on-clock-frequency-property.patch - 181-earlycon-remove-hardcoded-port-uartclk-initialization-in-of_setup_earlycon. patch - 700-1-6-e1000e-Remove-Other-from-EIAC.patch - 700-2-6-Partial-revert-e1000e-Avoid-receiver-overrun-interrupt-bursts.patch - 700-3-6-e1000e-Fix-queue-interrupt-re-raising-in-Other-interrupt.patch - 700-4-6-e1000e-Avoid-missed-interrupts-following-ICR-read.patch Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* build: add mkrasimageDavid Bauer2018-08-281-1/+1
| | | | | | | | | | | | | | | The current make-ras.sh image generation script for the ZyXEL NBG6617 has portability issues with bash. Because of this, factory images are currently not built correctly by the OpenWRT buildbots. This commit replaces the make-ras.sh by C-written mkrasimage. The new mkrasimage is also compatible with other ZyXEL devices using the ras image-format. This is not tested with the NBG6616 but it correctly builds the header for ZyXEL factory image. Signed-off-by: David Bauer <mail@david-bauer.net>
* treewide: fix some cosmetic glitches in dts filesPaul Wassi2018-08-271-1/+1
| | | | | | | | | | | - fix single spaces hidden by a tab - replace indentation with spaces by tabs - make empty lines empty - drop trailing whitespace - drop unnecessary blank lines Signed-off-by: Mathias Kresin <dev@kresin.me> Signed-off-by: Paul Wassi <p.wassi@gmx.at>
* treewide: drop unused get_status_led functionsMathias Kresin2018-08-161-4/+0
| | | | | | | The function isn't used for targets getting the status leds from the devicetree. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: fix upgrade led handlingMathias Kresin2018-08-161-2/+4
| | | | | | | | | | | | The upgrade led is only used if a running led is defined. If no running led is defined, the upgrade led is ignored and upgrade isn't indicated at all. Instead, turn off the running led prior to turning the upgrade led on. In most cases there isn't any visual change, but it allows to use an independent led for upgrade indication. Signed-off-by: Mathias Kresin <dev@kresin.me>
* treewide: consolidate upgrade state setMathias Kresin2018-08-161-6/+0
| | | | | | | | | | Set the (sys)upgrade state when sourcing the stage2 script instead of setting the state for each target individual. This change fixes the, due to a missing state set, not working upgrade led on ath79 and apm821xx. Signed-off-by: Mathias Kresin <dev@kresin.me>
* kernel: bump kernel 4.14 to version 4.14.63Hauke Mehrtens2018-08-152-27/+1
| | | | | | | | | | | | The following patches were integrated upstream: * target/linux/ipq40xx/patches-4.14/050-0006-mtd-nand-qcom-Add-a-NULL-check-for-devm_kasprintf.patch * target/linux/mediatek/patches-4.14/0177-phy-phy-mtk-tphy-use-auto-instead-of-force-to-bypass.patch This fixes tries to work around the following security problems: * CVE-2018-3620 L1 Terminal Fault OS, SMM related aspects * CVE-2018-3646 L1 Terminal Fault Virtualization related aspects Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
* kernel: bump 4.14 to 4.14.59Stijn Tintel2018-07-3116-103/+52
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Drop patch that was superseded upstream: ramips/0036-mtd-fix-cfi-cmdset-0002-erase-status-check.patch Drop upstreamed patches: - apm821xx/020-0001-crypto-crypto4xx-remove-bad-list_del.patch - apm821xx/020-0011-crypto-crypto4xx-fix-crypto4xx_build_pdr-crypto4xx_b.patch - ath79/0011-MIPS-ath79-fix-register-address-in-ath79_ddr_wb_flus.patch - brcm63xx/001-4.15-08-bcm63xx_enet-correct-clock-usage.patch - brcm63xx/001-4.15-09-bcm63xx_enet-do-not-write-to-random-DMA-channel-on-B.patch - generic/backport/080-net-convert-sock.sk_wmem_alloc-from-atomic_t-to-refc.patch - generic/pending/170-usb-dwc2-Fix-DMA-alignment-to-start-at-allocated-boun.patch - generic/pending/900-gen_stats-fix-netlink-stats-padding.patch In 4.14.55, a patch was introduced that breaks ext4 images in some cases. The newly introduced patch backport-4.14/500-ext4-fix-check-to-prevent-initializing-reserved-inod.patch addresses this breakage. Fixes the following CVEs: - CVE-2018-10876 - CVE-2018-10877 - CVE-2018-10879 - CVE-2018-10880 - CVE-2018-10881 - CVE-2018-10882 - CVE-2018-10883 Compile-tested: ath79, octeon, x86/64 Runtime-tested: ath79, octeon, x86/64 Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq40xx: Limit usable channels for OpenMesh A62 PHYsSven Eckelmann2018-07-301-0/+2
| | | | | | | | | The OpenMesh A62 is a tri-band device (1x 2.4GHz, 2x 5GHz) with special filters in front of the RX+TX paths to the 5GHz PHYs. These filtered channel can in theory still be used by the hardware but the signal strength is reduced so much that it makes no sense. Signed-off-by: Sven Eckelmann <sven.eckelmann@openmesh.com>
* ipq40xx: fix booting secondary CPU coresMantas Pucka2018-07-302-21/+35
| | | | | | | 95672e04 broke booting secondary cores by removing 'qcom,saw' property from L2 cache node. kpssv2_release_secondary() requires it. Signed-off-by: Mantas Pucka <mantas@8devices.com>
* ipq40xx: move essedma patches into same rangeJohn Crispin2018-07-253-9/+11
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: sync kernel configJohn Crispin2018-07-251-5/+3
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: use patches that were sent upstreamJohn Crispin2018-07-2527-296/+510
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: move dts file patches to end of seriesJohn Crispin2018-07-257-168/+168
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: cleanup USB supportJohn Crispin2018-07-253-462/+227
| | | | | | remove the 2 USB PHY drivers and add a generic PHY driver instead Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: drop no-op cpu_idle symbol patchJohn Crispin2018-07-252-30/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* ipq40xx: drop bus driver, its a no-op and only does lots of alloc/freeJohn Crispin2018-07-2412-12178/+0
| | | | Signed-off-by: John Crispin <john@phrozen.org>
* kernel: bump 4.14 to 4.14.53Koen Vandeputte2018-07-041-1/+1
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* kernel: bump 4.14 to 4.14.52Koen Vandeputte2018-07-021-4/+2
| | | | | | | | | Refreshed all patches Compile-tested on: cns3xxx, imx6, x86_64 Runtime-tested on: cns3xxx, imx6, x86_64 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
* ipq40xx: add support for the ZyXEL NBG6617Christian Lamparter2018-06-2610-1/+462
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for ZyXEL NBG6617 Hardware highlights: SOC: IPQ4018 / QCA Dakota CPU: Quad-Core ARMv7 Processor rev 5 (v7l) Cortex-A7 DRAM: 256 MiB DDR3L-1600/1866 Nanya NT5CC128M16IP-DI @ 537 MHz NOR: 32 MiB Macronix MX25L25635F ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4 x LAN, 1 x WAN) USB: 1 x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11bgn 2:2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11a/n/ac 2:2x2 INPUT: RESET Button, WIFI/Rfkill Togglebutton, WPS Button LEDS: Power, WAN, LAN 1-4, WLAN 2.4GHz, WLAN 5GHz, USB, WPS Serial: WARNING: The serial port needs a TTL/RS-232 3.3v level converter! The Serial setting is 115200-8-N-1. The 1x4 .1" header comes pre-soldered. Pinout: 1. 3v3 (Label printed on the PCB), 2. RX, 3. GND, 4. TX first install / debricking / restore stock: 0. Have a PC running a tftp-server @ 192.168.1.99/24 1. connect the PC to any LAN-Ports 2. put the openwrt...-factory.bin (or V1.00(ABCT.X).bin for stock) file into the tftp-server root directory and rename it to just "ras.bin". 3. power-cycle the router and hold down the the WPS button (for 30sek) 4. Wait (for a long time - the serial console provides some progress reports. The u-boot says it best: "Please be patient". 5. Once the power LED starts to flashes slowly and the USB + WPS LEDs flashes fast at the same time. You have to reboot the device and it should then come right up. Installation via Web-UI: 0. Connect a PC to the powered-on router. It will assign your PC a IP-address via DHCP 1. Access the Web-UI at 192.168.1.1 (Default Passwort: 1234) 2. Go to the "Expert Mode" 3. Under "Maintenance", select "Firmware-Upgrade" 4. Upload the OpenWRT factory image 5. Wait for the Device to finish. It will reboot into OpenWRT without any additional actions needed. To open the ZyXEL NBG6617: 0. remove the four rubber feet glued on the backside 1. remove the four philips screws and pry open the top cover (by applying force between the plastic top housing from the backside/lan-port side) Access the real u-boot shell: ZyXEL uses a proprietary loader/shell on top of u-boot: "ZyXEL zloader v2.02" When the device is starting up, the user can enter the the loader shell by simply pressing a key within the 3 seconds once the following string appears on the serial console: | Hit any key to stop autoboot: 3 The user is then dropped to a locked shell. |NBG6617> HELP |ATEN x[,y] set BootExtension Debug Flag (y=password) |ATSE x show the seed of password generator |ATSH dump manufacturer related data in ROM |ATRT [x,y,z,u] RAM read/write test (x=level, y=start addr, z=end addr, u=iterations) |ATGO boot up whole system |ATUR x upgrade RAS image (filename) |NBG6617> In order to escape/unlock a password challenge has to be passed. Note: the value is dynamic! you have to calculate your own! First use ATSE $MODELNAME (MODELNAME is the hostname in u-boot env) to get the challange value/seed. |NBG6617> ATSE NBG6617 |012345678901 This seed/value can be converted to the password with the help of this bash script (Thanks to http://www.adslayuda.com/Zyxel650-9.html authors): - tool.sh - ror32() { echo $(( ($1 >> $2) | (($1 << (32 - $2) & (2**32-1)) ) )) } v="0x$1" a="0x${v:2:6}" b=$(( $a + 0x10F0A563)) c=$(( 0x${v:12:14} & 7 )) p=$(( $(ror32 $b $c) ^ $a )) printf "ATEN 1,%X\n" $p - end of tool.sh - |# bash ./tool.sh 012345678901 | |ATEN 1,879C711 copy and paste the result into the shell to unlock zloader. |NBG6617> ATEN 1,0046B0017430 If the entered code was correct the shell will change to use the ATGU command to enter the real u-boot shell. |NBG6617> ATGU |NBG6617# Co-authored-by: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@googlemail.com> Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: bump 4.14 to 4.14.51Kevin Darbyshire-Bryant2018-06-262-8/+3
| | | | | | | | | | | | | | | | | | | | | | | The sender domain has a DMARC Reject/Quarantine policy which disallows sending mailing list messages using the original "From" header. To mitigate this problem, the original message has been wrapped automatically by the mailing list software. Refresh patches. Remove patch that can be reverse applied: mvebu/patches-4.14/530-ATA-ahci_mvebu-enable-stop_engine-override.patch mvebu/patches-4.14/531-ATA-ahci_mvebu-pmp-stop-errata-226.patch Update patch that no longer applied: ipq806x/patches-4.14/0035-clk-mux-Split-out-register-accessors-for-reuse.patch Compiled-tested-for: lantiq, ramips Run-tested-on: lantiq BT hh5a, ramips MIR3g Signed-off-by: Kevin Darbyshire-Bryant <ldir@darbyshire-bryant.me.uk> Tested-by: Michael Yartys <michael.yartys@protonmail.com> Tested-by: Rosen Penev <rosenp@gmail.com>
* ipq40xx: add support for ZyXEL WRE6606Magnus Frühling2018-06-187-2/+300
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 128 MB Nanya NT5CC64M16GP-DI FLASH: 16 MiB Macronix MX25L12845EMI-12G ETH: Qualcomm QCA8072 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5GHz 802.11n/ac W2 2x2 INPUT: WPS, Mode-toggle-switch LED: Power, WLAN 2.4GHz, WLAN 5GHz, LAN, WPS (LAN not controllable by software) (WLAN each green / red) SERIAL: Header next to eth-phy. VCC, TX, GND, RX (Square hole is VCC) The Serial setting is 115200-8-N-1. Tested and working: - Ethernet (Correct MAC-address) - 2.4 GHz WiFi (Correct MAC-address) - 5 GHz WiFi (Correct MAC-address) - Factory installation from tftp - OpenWRT sysupgrade - LEDs - WPS Button Not Working: - Mode-toggle-switch Install via TFTP: Connect to the devices serial. Hit Enter-Key in bootloader to stop autobooting. Command `tftpboot` will pull an initramfs image named `C0A86302.img` from a tftp server at `192.168.99.08/24`. After successfull transfer, boot the image with `bootm`. To persistently write the firmware, flash an openwrt sysupgrade image from inside the initramfs, for example transfer via `scp <sysupgrade> root@192.168.1.1:/tmp` and flash on the device with `sysupgrade -n /tmp/<sysupgrade>`. append-cmdline patch taken from chunkeeys work on the NBG6617. Signed-off-by: Magnus Frühling <skorpy@frankfurt.ccc.de> Co-authored-by: David Bauer <mail@david-bauer.net> Co-authored-by: Christian Lamparter <chunkeey@googlemail.com>
* ipq40xx: essedma: fixup ip alignChen Minqiang2018-06-181-0/+26
| | | | | | | | This fixup ip align in essedma driver rx path see cat /proc/cpu/alignment which reports alignment-fixups without this fix. Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq40xx: add get_status_led to diag.shDavid Bauer2018-06-181-0/+4
| | | | | | | | | | | This commit adds the get_status_led method to diag.sh, which sets the boot-led as status-led for scripts using this method to get a status-led. This method is used platform-independent in downstream project gluon to set the LED used to indicate the config-mode. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: flesh out MR33's pcie dts definitionsChristian Lamparter2018-06-081-0/+13
| | | | Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix OpenMesh A62 dtc warningsChristian Lamparter2018-06-081-8/+6
| | | | | | | | | | | | | | | | | Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing ranges for PCI bridge (or not a bridge) Warning (pci_bridge): Node /soc/pci@40000000/pcie@0 missing bus-range for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 node name is not "pci" or "pcie" Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing ranges for PCI bridge (or not a bridge) Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #address-cells for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 incorrect #size-cells for PCI bridge Warning (pci_bridge): Node /soc/pci@40000000/pcie@0/ath10k@0,0 missing bus-range for PCI bridge Warning (unit_address_format): Failed prerequisite 'pci_bridge' Warning (pci_device_reg): Failed prerequisite 'pci_bridge' Warning (pci_device_bus_num): Failed prerequisite 'pci_bridge' Cc: Sven Eckelmann <sven.eckelmann@openmesh.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> Tested-by: Sven Eckelmann <sven.eckelmann@open-mesh.com>
* ipq40xx: fix dtc warning about /soc/ad-hoc-bus missing a unit nameChristian Lamparter2018-06-081-1/+1
| | | | | | | This patch fixes a dtc warning that shows up for every device Warning (unit_address_vs_reg): Node /soc/ad-hoc-bus has a reg or ranges property, but no unit name Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: set #size-cells to 0 to fix warningChristian Lamparter2018-06-081-1/+1
| | | | | | | | | | | qcom-ipq4018-ex6100v2.dtb: Warning (reg_format): "reg" property in /led_spi/led_gpio@0 has invalid length (4 bytes) qcom-ipq4018-ex6100v2.dtb: Warning (avoid_default_addr_size): Relying on default #size-cells value for /led_spi/led_gpio@0 Cc: Thomas Hebb <tommyhebb@gmail.com> Cc: David Bauer <mail@david-bauer.net> Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* kernel: bump 4.14 to 4.14.48Stijn Tintel2018-06-051-11/+11
| | | | | | | | | | | | | | | | | | Remove upstreamed patches: generic/pending/101-clocksource-mips-gic-timer-fix-clocksource-counter-w.patch generic/pending/103-MIPS-c-r4k-fix-data-corruption-related-to-cache-coherence.patch generic/pending/182-net-qmi_wwan-add-BroadMobi-BM806U-2020-2033.patch lantiq/0025-MIPS-lantiq-gphy-Remove-reboot-remove-reset-asserts.patch Update patches that no longer apply: generic/pending/811-pci_disable_usb_common_quirks.patch ath79/0009-MIPS-ath79-add-lots-of-missing-registers.patch Fixes CVE-2018-6412. Compile-tested: octeon, x86/64. Runtime-tested: octeon, x86/64. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* ipq40xx: add eva-image for FRITZ!Box 4040David Bauer2018-05-221-1/+4
| | | | | | | | | This commit adds an EVA flashable image for the FRITZ!Box 4040. The image contains the U-Boot with OpenWRT appended to it. This way we remove the need to use UART for initial flashing. Signed-off-by: David Bauer <mail@david-bauer.net>
* kernel: enable THIN_ARCHIVES by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | THIN_ARCHIVES option is enabled by default in the kernel configuration and no one target config disables it. So enable it by default and remove this symbol from target specific configs to keep them light. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable FUTEX_PI by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | | New FUTEX_PI configuration symbol enabled if FUTEX and RT_MUTEX symbols are enabled. Both of these symbols are enabled by default in the generic config, so enable FUTEX_PI by default too to keep platform specific configs minimal. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: enable EXPORTFS by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | OVERLAY_FS config symbol selects EXPORTFS since 4.12 kernel, we have OVERLAY_FS enabled by default, so enable EXPORTFS in the generic config of 4.14 and remove this option from platform specific configs. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DRM_LIB_RANDOM by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | DRM_LIB_RANDOM config symbol selected only by DRM_DEBUG_MM_SELFTEST which is disable by default, so disable DRM_LIB_RANDOM by default too. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable DMA_{NOOP|VIRT}_OPS by defaultSergey Ryazanov2018-05-221-2/+0
| | | | | | | These options do not used by any supported arch, so disable them by default to make arch configs a bit more clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* kernel: disable ARCH_WANTS_THP_SWAP by defaultSergey Ryazanov2018-05-221-1/+0
| | | | | | | | Only one arch (x86_64) enables this option. So disable ARCH_WANTS_THP_SWAP by default and remove referencies to it from all configs (except x86_64) to make them clean. Signed-off-by: Sergey Ryazanov <ryazanov.s.a@gmail.com>
* ipq40xx: fix ethernet on ap-dk01.1Roman Yeryomin2018-05-181-0/+25
| | | | | | | Not sure how it worked before but ethernet is disabled by default in ipq4019 dtsi. Signed-off-by: Roman Yeryomin <roman@advem.lv>
* kernel: bump 4.14 to 4.14.36Koen Vandeputte2018-04-261-1/+1
| | | | | | | | | | | | | | | | Refreshed all patches. Compile-tested on: cns3xxx, imx6 Runtime-tested on: cns3xxx, imx6 Fixes for CVEs: CVE-2018-1108 CVE-2018-1092 CVE-2018-1094 CVE-2018-1095 Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com> Tested-by: Stijn Segers <foss@volatilesystems.org>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-04 09:12:15 +0000