aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/image
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: wpj428: switch to zimage to fit kernel partitionLeon M. Busch-George2023-10-211-1/+1
| | | | | | | | | | | | | | | | Like with some other ipq40xx devices, the kernel image size for the WPJ428 is limited in stock u-boot. For that reason, the current release doesn't include an image for the board. By switching to the zImage format, the kernel image size is reduced which re-enables the build process. The image boots and behaved normally through a few days of testing. Before the switch to kernel version 6.1, it was possible to reduce the image size by enough when disabling UBIFS and its otherwise unneeded dependencies. Signed-off-by: Leon M. Busch-George <leon@georgemail.eu> (cherry picked from commit 2657e8cab7f3d621b66cfdd4e228da3b912af32a)
* ipq40xx: refactor ZTE MF287 seriesAndreas Böhler2023-09-241-3/+10
| | | | | | | | | The ZTE MF287 requires a different board calibration file for ath10k than the ZTE MF287+. The two devices receive their own DTS, thus the device tree is slightly refactored. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit 9c7578d560708c040dc04d0db37ef682db58f6b5)
* ipq40xx: fix image building for ZTE MF287 seriesAndreas Böhler2023-09-181-1/+1
| | | | | | | | | For the ZTE MF287 series, a special recovery image is built. The Makefile worked fine on snapshot, but created corrupt images on the 23.05 images. By using the appropriate variable, this should be fixed. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit a9cc3708e0c3c4869711a9ba4b9c1437ed250721)
* ipq4019: add support for ZTE MF287 Pro aka DreiNeo ProAndreas Böhler2023-08-211-5/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287 Pro is a LTE router used (exclusively?) by the network operator "3". It is very similar to the MF287+, but the hardware layout and partition layout have changed quite a bit. Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 WiFi: 802.11a/b/g/n/ac SoC-integrated USB: 1x 2.0 MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m17 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd17 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock17 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 17 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Other Notes =========== Contrary to the stock firmware, the USB port on the back can be used. There is one GPIO Switch "Power button blocker" which, if enabled, does not trigger a reset of the SoC if the modem reboots. If disabled, the SoC is rebooted along with the modem. The modem can be rebooted via the exported GPIO "modem-reset" in /sys/class/gpio. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit edfe91372adfdaf5ee4e294fb0f5860a16adc551)
* ipq40xx: meraki: define DTB load addressRobert Marko2023-08-151-2/+1
| | | | | | | | | | | | | | | | | | | | | | It seems that the Meraki bootloader does not respect the kernel ARM booting specification[1] that requires that address where DTB is located needs to be 64-bit aligned and often places the DTB on a non 64-bit aligned address and then kernel fails to find the DTB magic and fails to boot. Even worse, there is no prints until early printk is enabled and then its visible that kernel is trying to find the ATAG-s as DTB was not found or is invalid. Unifi 6 devices had the same issue and it can be solved by passing the load adress as part of the FIT image. It seems that the vendor was aware of the issue and is always relocating the DTB to 0x89000000, so lets just do the same. Now that booting is reliable, reenable default images for the Meraki MR33 and MR74 devices. Reviewed-by: Lech Perczak lech.perczak@gmail.com Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit f1c80445bd7e3b2f7fc3e4c8136402b30834d4e9)
* ipq40xx: meraki: remove swconfig in DEVICE_PACKAGESRobert Marko2023-08-151-1/+1
| | | | | | | | ipq40xx was converted to DSA and swconfig is not being included at all in the default packages so there is no need to drop it from device packages. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit bb4a25860f593790aaedc1b31dde33fbc519e7bf)
* ipq40xx: commonize Meraki recipeRobert Marko2023-08-151-8/+7
| | | | | | | | MR33 and MR74 share pretty much everything in the image recipe, so lets extract a common recipe to avoid duplication. Signed-off-by: Robert Marko <robimarko@gmail.com> (cherry picked from commit 9e9dc1890c6f58d858208136ecfa435445dfca09)
* ipq40xx: add support for Teltonika RUTX50David Bauer2023-07-261-0/+16
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Hardware -------- CPU: Qualcomm IPQ4018 RAM: 256M Flash: 16MB SPI-NOR (W25Q128) 128MB SPI-NAND (XTX) WiFi: 2T2R (2GHz 802.11n ; 5 GHz 802.11ac) ETH: 4x LAN ; 1x WAN (Gigabit) CELL: Quectel RG501Q 3G/4G/5G UART: Available on the goldfinger connector (Pinout silkscreened) 115200 8N1 3V3 - Only connect RX / TX / GND Installation ------------ 1. Enable SSH in the Teltonika UI (System --> Administration --> Access Control) 2. Check from which partition set the device is currently running from. $ cat /proc/boot_info/rootfs/primaryboot In case this output reads 0, install a Software update from Teltonika first. After upgrade completion, check this file now reads 1 before continuing. 2. Transfer the OpenWrt factory image to the device using scp. Use the same password (user root!) as used for the Web-UI. $ scp -O openwrt-factory.bin root@192.168.1.1:/tmp 3. Connect to the device using ssh as the root user. 4. Install OpenWrt by writing the factory image to flash. $ ubiformat /dev/mtd16 -y -f /tmp/openwrt-factory.bin 5. Instruct the bootloaer to boot from the first partition set. $ echo 0 > /proc/boot_info/rootfs/primaryboot $ cat /proc/boot_info/getbinary_bootconfig > /tmp/bootconfig.bin $ cat /proc/boot_info/getbinary_bootconfig1 > /tmp/bootconfig1.bin $ mtd write /tmp/bootconfig.bin /dev/mtd2 $ mtd write /tmp/bootconfig1.bin /dev/mtd3 6. Reboot the device. $ reboot Signed-off-by: David Bauer <mail@david-bauer.net> (cherry picked from commit 844bb4bfad84cc6267f9b138d1f63b07ed3b77d0)
* ipq-wifi: fix upstream board-2.bin ZTE M289F snafuChristian Lamparter2023-07-041-1/+1
| | | | | | | | | | | | | | | | | | | | | The upstream board-2.bin file in the linux-firmware.git repository for the QCA4019 contains a packed board-2.bin for this device for both 2.4G and 5G wifis. This isn't something that the ath10k driver supports. Until this feature either gets implemented - which is very unlikely -, or the upstream boardfile is mended (both, the original submitter and ath10k-firmware custodian have been notified). OpenWrt will go back and use its own bespoke boardfile. This unfortunately means that 2.4G and on some revisions the 5G WiFi is not available in the initramfs image for this device. Fixes: #12886 Reported-by: Christian Heuff <christian@heuff.at> Debugged-by: Georgios Kourachanis <geo.kourachanis@gmail.com> Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 75505c5ec724b9b961dcb411bac1d4b9aede3e1d)
* ipq4019: add support for ZTE MF287+ aka DreiNeoAndreas Böhler2023-07-011-0/+18
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The ZTE MF287+ is a LTE router used (exclusively?) by the network operator "3". The MF287 (i.e. non-plus aka 3Neo) is also supported (the only difference is the LTE modem) Specifications ============== SoC: IPQ4018 RAM: 256MiB Flash: 8MiB SPI-NOR + 128MiB SPI-NAND LAN: 4x GBit LAN LTE: ZTE Cat12 (MF287+) / ZTE Cat6 (MF287) WiFi: 802.11a/b/g/n/ac SoC-integrated MAC addresses ============= LAN: from config + 2 WiFi 1: from config WiFi 2: from config + 1 Installation ============ Option 1 - TFTP --------------- TFTP installation using UART is preferred. Disassemble the device and connect serial. Put the initramfs image as openwrt.bin to your TFTP server and configure a static IP of 192.168.1.100. Load the initramfs image by typing: setenv serverip 192.168.1.100 setenv ipaddr 192.168.1.1 tftpboot 0x82000000 openwrt.bin bootm 0x82000000 From this intiramfs boot you can take a backup of the currently installed partitions as no vendor firmware is available for download: ubiattach -m14 cat /dev/ubi0_0 > /tmp/ubi0_0 cat /dev/ubi0_1 > /tmp/ubi0_1 Copy the files /tmp/ubi0_0 and /tmp/ubi0_1 somewhere save. Once booted, transfer the sysupgrade image and run sysupgrade. You might have to delete the stock volumes first: ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N kernel Option 2 - From stock firmware ------------------------------ The installation from stock requires an exploit first. The exploit consists of a backup file that forces the firmware to download telnetd via TFTP from 192.168.0.22 and run it. Once exploited, you can connect via telnet and login as admin:admin. The exploit will be available at the device wiki page. Once inside the stock firmware, you can transfer the -factory.bin file to /tmp by using "scp" from the stock frmware or "tftp". ZTE has blocked writing to the NAND. Fortunately, it's easy to allow write access - you need to read from one file in /proc. Once done, you need to erase the UBI partition and flash OpenWrt. Before performing the operation, make sure that mtd13 is the partition labelled "rootfs" by calling "cat /proc/mtd". Complete commands: cd /tmp tftp -g -r factory.bin 192.168.0.22 cat /proc/driver/sensor_id flash_erase /dev/mtd13 0 0 dd if=/tmp/factory.bin of=/dev/mtdblock13 bs=131072 Afterwards, reboot your device and you should have a working OpenWrt installation. Restore Stock ============= Option 1 - via UART ------------------- Boot an OpenWrt initramfs image via TFTP as for the initial installation. Transfer the two backed-up files to your box to /tmp. Then, run the following commands - replace $kernel_length and $rootfs_size by the size of ubi0_0 and ubi0_1 in bytes. ubiattach -m 14 ubirmvol /dev/ubi0 -N kernel ubirmvol /dev/ubi0 -N rootfs ubirmvol /dev/ubi0 -N rootfs_data ubimkvol /dev/ubi0 -N kernel -s $kernel_length ubimkvol /dev/ubi0 -N ubi_rootfs -s $rootfs_size ubiupdatevol /dev/ubi0_0 /tmp/ubi0_0 ubiupdatevol /dev/ubi0_1 /tmp/ubi0_1 Option 2 - from within OpenWrt ------------------------------ This option requires to flash an initramfs version first so that access to the flash is possible. This can be achieved by sysupgrading to the recovery.bin version and rebooting. Once rebooted, you are again in a default OpenWrt installation, but no partition is mounted. Follow the commands from Option 1 to flash back to stock. LTE Modem ========= The LTE modem is similar to other ZTE devices and controls some more LEDs and battery management. Configuring the connection using uqmi works properly, the modem provides three serial ports and a QMI CDC ethernet interface. Signed-off-by: Andreas Böhler <dev@aboehler.at> (cherry picked from commit f70ee53b08466f612546f699c556cbdaa39e1466)
* ipq40xx: meraki-mr33, meraki-mr74: disable image generationLech Perczak2023-06-251-0/+2
| | | | | | | | | | | | | | After migrating to kernel 5.15, upgrading causes the units to become soft-bricked, hanging forever at the kernel startup. Kernel size limitation of 4000000 bytes is suspected here, but this is not fully confirmed. Disable the images to protect users from inadvertent bricking of units, because recovery of those is painful with Cisco's U-boot, until the root cause is found and fixed. Signed-off-by: Lech Perczak <lech.perczak@gmail.com> (cherry picked from commit 9d64cc068fbb15d9e6498c1eba79851823b2f4f5)
* ipq40xx: convert Buffalo WTR-M2133HP to DSAYanase Yuki2023-06-081-2/+1
| | | | | | | This commit convert WTR-M2133HP to DSA setup. Signed-off-by: Yanase Yuki <dev@zpc.sakura.ne.jp> (cherry picked from commit edb3a4162c0763ecc9d5e7660700a68a25bf28e3)
* ipq40xx: e2600ac-c1 remove KERNEL_SIZE张 鹏2023-05-311-2/+0
| | | | | | | | | | Currently, e2600ac-c1 cannot be built as the kernel is larger than the defined KERNEL_SIZE, however, there is no bootloader limit for the kernel size so remove KERNEL_SIZE completely. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ improve commit title, fix merge conflict ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit b764268acb7ed410d1d81e783f1b0ce407efda82)
* ipq40xx: add e2600ac c2 to dsa张 鹏2023-05-311-2/+1
| | | | | | | | | Convert E2600ac c2 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 0dca52cf595cedcabec5d384ddc83f1954cca46d)
* ipq40xx: add e2600ac c1 to dsa张 鹏2023-05-311-2/+1
| | | | | | | | | Convert E2600ac c1 to DSA and enable it. Signed-off-by: 张 鹏 <sd20@qxwlan.com> [ rename port to more generic name ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com> (cherry picked from commit 7f2ecab0f4623e9b437b1a6656275695ac063fe4)
* ipq40xx: convert EZVIZ CS-W3-WD1200G-EUP to DSAChristian Lamparter2023-05-201-2/+1
| | | | | | Convert the repeater to DSA. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq-wifi: drop upstreamed board-2.binChristian Lamparter2023-05-181-20/+10
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The BDFs for the: Aruba AP-365 Devolo Magic 2 WiFi next Edgecore ECW5410 Edgecore OAP100 Extreme Networks WS-AP3915i GL.iNet GL-A1300 GL.iNet GL-AP1300 GL.iNet GL-S1300 Linksys EA8300 Linksys WHW03v2 Nokia Wi4A AC400i P&W R619AC Pakedge WR-1 Qxwlan E2600AC C1 Sony NCP-HG100/Cellular Teltonika RUTX10 ZTE MF18A were upstreamed to the ath10k-firmware repository and landed in linux-firmware.git. Furthermore the BDFs for the: 8devices Habanero 8devices Jalapeno Qxwlan E2600AC C2 have been updated. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: convert AVM FRITZ!Repeater 3000 to DSANick Hainke2023-05-031-2/+1
| | | | | | Convert the repeater to DSA. Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert GL-AP1300 to DSANick Hainke2023-04-241-2/+1
| | | | | | | | | | Convert GL-AP1300 to DSA and enable it. While working on it rename the GL-AP1300 leds from green to white. Tested-by: Rob White <rob@blue-wave.net> Tested-by: Robert Sommer <frauhottelmann@gmail.com> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: convert AP-365 to DSADavid Bauer2023-04-151-2/+1
| | | | | | | | | Re-enable the Aruba AP-365 with DSA support. Changes are trvivial, as the board design is pretty much the already updated AP-303. Run-tested on the device. Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: add support for Wallystech DR40x9Robert Marko2023-03-211-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Adds support for the Wallys DR40x9 series boards. They come in IPQ4019 and IPQ4029 versions. IPQ4019/4029 only differ in that that IPQ4029 is the industrial version that is rated to higher temperatures. Specifications are: * CPU: Qualcomm IPQ40x9 (4x ARMv7A Cortex A7) at 716 MHz * RAM: 512 MB * Storage: 2MB of SPI-NOR, 128 MB of parallel NAND * USB 3.0 TypeA port for users * MiniPCI-E with PCI-E 2.0 link * MiniPCI-E for LTE modems with only USB2.0 link * 2 SIM card slots that are selected via GPIO11 * MicroSD card slot * Ethernet: 2x GBe with 24~48V passive POE * SFP port (Does not work, I2C and GPIO's not connected on hardware) * DC Jack * UART header * WLAN: In-SoC 2x2 802.11b/g/n and 2x2 802.11a/n/ac * 4x MMCX connectors for WLAN * Reset button * 8x LED-s Installation instructions: Connect to UART, pins are like this: -> 3.3V | TX | RX | GND Settings are 115200 8n1 Boot initramfs from TFTP: tftpboot 0x84000000 openwrt-ipq40xx-generic-wallys_dr40x9-initramfs-fit-uImage.itb bootm Then copy the sysupgrade image to the /tmp folder and execute sysupgrade -n <image_name> The board file binary was provided from Wallystech on March 14th 2023 including full permission to use and distribute. Signed-off-by: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Koen Vandeputte <koen.vandeputte@citymesh.com>
* ipq40xx: update Crisis Innovation Lab MeshPoint.One BDFMantas Pucka2023-03-171-1/+1
| | | | | | | | | | Make sure it uses updated Jalapeno BDF inherited from Device/8dev_jalapeno-common Fixes: 146eb4925c7f ("ipq40xx: add support for Crisis Innovation Lab MeshPoint.One") Signed-off-by: Mantas Pucka <mantas@8devices.com> [ fix Fixes tag to correct format and fix commit title ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: set specific BDF file for 8devices Habanero/JalapenoMantas Pucka2023-03-171-0/+2
| | | | | | | | | Set specific BDF file for 8devices Habanero/Jalapeno in ipq40xx generic.mk Signed-off-by: Mantas Pucka <mantas@8devices.com> [ split ipq40xx changes in separate commit ] Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
* ipq40xx: convert Netgear EX6100/EX6150 v2 to DSADavid Bauer2023-03-081-4/+2
| | | | Signed-off-by: David Bauer <mail@david-bauer.net>
* ipq40xx: chromium: Enable kmod-ramoops by defaultBrian Norris2023-02-181-1/+5
| | | | | | | | Chromium devices (like Google WiFi) have ramoops memory reserved by the bootloader. Let's enable the ramoops kernel module by default, so we get better crash logging. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* ipq40xx: convert Extreme AP3915i to DSAJames Andrewartha2023-01-171-2/+1
| | | | | | Convert and re-enabled Extreme AP3915i to DSA. Signed-off-by: James Andrewartha <trs80@ucc.asn.au>
* ipq40xx: add DSL support for FritzBox 7530Martin Schiller2023-01-161-1/+1
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Set up MAC, LED, settings and default packages for DSL usage, similar to the lantiq target. Due to licensing uncertainty, we do not include the firmware files for the DSL drivers. To have a working DSL setup, follow the instructions below. Download the firmware files locally: mkdir -p files/lib/firmware/09a9 wget -P files/lib/firmware/09a9 https://gitlab.com/prpl-foundation/intel/vrx518_aca_fw/-/raw/ugw-8.5.2/platform/xrx500/aca_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/vrx518_ppe_fw/-/raw/ugw_8.5.2.10/platform/xrx500/ppe_fw.bin wget -P files/lib/firmware https://gitlab.com/prpl-foundation/intel/dsl_vr11_firmware_xdsl/-/raw/ugw-8.5.2/xcpe_8D1507_8D0901.bin ln -s xcpe_8D1507_8D0901.bin files/lib/firmware/vdsl.bin For people building their own images: Run the above commands in the root of your local OpenWrt clone, and the firmware files will be part of the resulting images. For people downloading images: Copy the firmware files onto the router once it's booted up: scp -O -r files/lib/firmware root@fritz:/lib Reboot the device afterwards. Signed-off-by: Martin Schiller <ms.3headeddevs@gmail.com> [cleaned up] Signed-off-by: Andre Heider <a.heider@gmail.com> [set up LED] Signed-off-by: Jan Hoffmann <jan@3e8.eu> Signed-off-by: Andre Heider <a.heider@gmail.com>
* ipq40xx: add support for Linksys WHW03 V2Vincent Tremblay2023-01-151-0/+17
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | SOC: Qualcomm IPQ4019 WiFi 1: QCA4019 IEEE 802.11b/g/n WiFi 2: QCA4019 IEEE 802.11a/n/ac WiFi 3: QCA8888 IEEE 802.11a/n/ac Bluetooth: Qualcomm CSR8811 (A12U) Zigbee: Silicon Labs EM3581 NCP + Skyworks SE2432L Ethernet: Qualcomm Atheros QCA8072 (2-port) Flash 1: Mactronix MX30LF4G18AC-XKI RAM (NAND): SK hynix H5TC4G63CFR-PBA (512MB) LED Controller: NXP PCA9633 (I2C) Buttons: Single reset button (GPIO). - The three WiFis were fully tested and are configured with the same settings as in the vendor firmware. - The specific board files were submitted to the ATH10k mailing list but I'm still waiting for a reply. They can be removed once they are approved upstream. - Two ethernet ports are accessible on the device. By default one is configured as WAN and the other one is LAN. They are fully working. Bluetooth: ======== - Fully working with the following caveats: - RFKILL need to be enabled in the kernel. - An older version of bluez is needed as bccmd is needed to configure the chip. Zigbee: ====== - The spidev device is available in the /dev directory. - GPIOs are configured the same way as in the vendor firmware. - Tests are on-going. I am working on getting access to the Silicon Labs stack to validate that it is fully working. Installation: ========= The squash-factory image can be installed via the Linksys Web UI: 1. Open "http://192.168.1.1/ca" (Change the IP with the IP of your device). 2. Login with your admin password. 3. To enter into the support mode, click on the "CA" link and the bottom of the page. 4. Open the "Connectivity" menu and upload the squash-factory image with the "Choose file" button. 5. Click start. Ignore all the prompts and warnings by click "yes" in all the popups. The device uses a dual partition mechanism. The device automatically revert to the previous partition after 3 failed boot attempts. If you want to force the previous firmware to load, you can turn off and then turn on the device for 2 seconds, 3 times in a row. It can also be done via TFTP: 1. Setup a local TFTP server and configure its IP to 192.168.1.100. 2. Rename your image to "nodes_v2.img" and put it to the TFTP root of your server. 3. Connect to the device through the serial console. 4. Power on device and press enter when prompted to drop into U-Boot. 5. Flash the partition of your choice by typing "run flashimg" or "run flashimg2". 6. Once flashed, enter "reset" to reboot the device. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Vincent Tremblay <vincent@vtremblay.dev>
* ipq40xx: Add support ZTE MF18AMarcin Gajda2023-01-141-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Light and small router ( In Poland operators sells together with MC7010 outdoor modem to provide WIFI inside home). Device specification SoC Type: Qualcomm IPQ4019 RAM: 256 MiB Flash: 128 MiB SPI NAND (Winbond W25N01GV) ROM: 2MiB SPI Flash (GD25Q16) Wireless 2.4 GHz (IP4019): b/g/n, 2x2 Wireless 5 GHz (QCA9982): a/n/ac, 3x3 Ethernet: 2xGbE (WAN/LAN1, LAN2) USB ports: No Button: 2 (Reset/WPS) LEDs: 3 external leds: Power (blue) , WiFI (blue and red), SMARTHOME (blue and red) and 1 internal (blue) -- NOTE: Power controls all external led (if down ,all others also not lights even signal is up) Power: 5VDC, 2,1A via USB-C socket Bootloader: U-Boot On board ZWave and Zigbee (EFR32 MG1P232GG..) modules ( not supported by orginal software ) Installation 1.Open MF18A case by ungluing rubber pad under the router and unscrew screws, and connect to serial console port, with the following pinout, starting from pin 1, which is the topmost pin when the board is upright (reset button on the bottom) : VCC (3.3V). Do not use unless you need to source power for the converer from it. TX RX GND Default port configuration in U-boot as well as in stock firmware is 115200-8-N-1. 2.Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 3.Connect TFTP server to RJ-45 port (WAN/LAN1). 4.Power on MF18A , stop in u-Boot (using ESC button) and run u-Boot commands: setenv serverip 192.168.0.2 setenv ipaddr 192.168.0.1 set fdt_high 0x85000000 tftpboot 0x84000000 openwrt-ipq40xx-generic-zte_mf18a-initramfs-fit-zImage.itb bootm 0x84000000 5.Please make backup of original partitions, if you think about revert to stock, specially mtd8 (Web UI) and mtd9 (rootFS). Use /tmp as temporary storage and do: WEB PARITION cat /dev/mtd8 > /tmp/mtd8.bin scp /tmp/mtd8.bin root@YOURSERVERIP:/ rm /tmp/mtd8.bin ROOT PARITION cat /dev/mtd9 > /tmp/mtd9.bin scp /tmp/mtd9.bin root@YOURSERVERIP:/ rm /tmp/mtd9.bin If you are sure ,that you want to flash openwrt, from uBoot, before bootm, clean rootfs partition with command: nand erase 0x1800000 0x1D00000 6.Login via ssh or serial and remove stock partitions (default IP 192.168.1.1): ubiattach -m 9 # it could return error if ubi was attached before or rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs # it could return error if rootfs part was erased before ubirmvol /dev/ubi0 -N ubi_rootfs_data # some devices doesn't have it 7. Install image via : sysupgrade -n /tmp/openwrt-ipq40xx-generic-zte_mf18a-squashfs-sysupgrade.bin previously wgeting bin. Sometimes it could print ubi attach error, but please ignore it if process goes forward. Back to Stock (!!! need original dump taken from initramfs !!!) ------------- Place mtd8.bin and mtd9.bin initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.0.2 Connect serial console (115200,8n1) to serial console connector . Connect TFTP server to RJ-45 port (WAN/LAN1). rename mtd8.bin to web.img and mtd9.bin to root_uImage_s Stop in u-Boot (using ESC button) and run u-Boot commands: This will erase Web and RootFS: nand erase 0x1000000 0x800000 nand erase 0x1800000 0x1D00000 This will restore RootFS: tftpboot 0x84000000 root_uImage_s nand erase 0x1800000 0x1D00000 nand write 0x84000000 0x1800000 0x1D00000 This will restore Web Interface: tftpboot 0x84000000 web.img nand erase 0x1000000 0x800000 nand write 0x84000000 0x1000000 0x800000 After first boot on stock firwmare, do a factory reset. Push reset button for 5 seconds so all parameters will be reverted to the one printed on label on bottom of the router As reference was taken MF289F support by Giammarco Marzano stich86@gmail.com and MF286D by Pawel Dembicki paweldembicki@gmail.com Signed-off-by: Marcin Gajda <mgajda@o2.pl>
* ipq40xx: migrate Linksys WHW01 to DSA and re-enableTony Ambardar2022-12-311-2/+1
| | | | | | | | | Convert Linksys WHW01 network configuration to DSA and re-enable builds. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: fix up Linksys WHW01 board name, device definitionTony Ambardar2022-12-311-7/+4
| | | | | | | | | | | | | | Update the board name defined in DTS to match online documentation and the name encoded into factory firmware. This helps supports flashing firmware factory images using 'sysupgrade'. Original WHW01 device definition assumes the rootfs IMAGE_SIZE is 33 MB instead of the correct 74 MB, and defines factory images which include extra adjustments/padding that do not match OEM factory images and may cause problems flashing. Update image size and build recipe to fix these. Suggested-by: Wyatt Martin <wawowl@gmail.com> Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: re-enable EA6350v3, EA8300, MR8300 buildsTony Ambardar2022-12-311-15/+27
| | | | | | | | | | | | | | | | | | | | | | | | | Raise the kernel size from 3 MB to 5 MB for EA6350v3, EA8300 and MR8300, and correspondingly reduce the rootfs size by 2 MB: * modify partition definitions in related .dts files * modify device kernel/image sizes in generic.mk Update to compat-version 2.0 to force factory image usage on sysupgrade, noting the current version 1.1 is an unreleased update for DSA migration. Also update the compat-version message, explaining the need to run one of the following console commands to update U-Boot's kernel-size variable before flashing the OpenWrt factory image. fw_setenv kernsize 500000 # (OpenWrt command line) setenv kernsize 500000 ; saveenv # (U-Boot serial console) Finally, re-enable the 3 devices. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Nicolas TORMO <badulesia.granieri@gmail.com> # MR8300 Tested-by: Tony Ambardar <itugrok@yahoo.com> # EA6350v3 Signed-off-by: Tony Ambardar <itugrok@yahoo.com>
* ipq40xx: convert Aruba AP-303H to DSA and enable target againNick Hainke2022-12-291-2/+1
| | | | | | | | | The target was disabled since noone did the DSA conversion. Add the conversion and enable it again. Tested-by: John Walshaw <jjw@myself.com> Signed-off-by: Bjoern Dobe <bjoern@dobecom.de> Signed-off-by: Nick Hainke <vincent@systemli.org>
* ipq40xx: add support for Mikrotik wAP R ac / LTE / LTE6Alexander Couzens2022-11-271-0/+20
| | | | | | | | | | | | | | | | | | | | | | | | | | | | The Mikrotik wAP R AC is an outdoor, dual band, dual radio (802.11ac) AP with a miniPCIe slot for a LTE modem. The wAP R AC is similar to the wAP AC but with the miniPCIe slot. The wAP R AC requires installing a LTE modem. The wAP LTE and wAP LTE6 comes with a LTE modem installed. See https://mikrotik.com/product/wap_r_ac for more info. Specifications: - SoC: Qualcomm Atheros IPQ4018 - CPU: 4x ARM Cortex A7 - RAM: 128MB - Storage: 16MB NOR flash - Wireless: - Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, internal antenna - Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, internal antenna - Ethernet: Built-in IPQ4018 (SoC, QCA8075) , 2x 1000/100/10 ports one with 802.3af/at PoE in - 1x Mini PCI-E port (USB2) Installation: Boot the initramfs image via TFTP, then flash the sysupgrade image using sysupgrade. Details at https://openwrt.org/toh/mikrotik/common. Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
* ipq40xx: remove '-fit' string from kernel filenamesDaniel Golle2022-11-241-4/+4
| | | | | | | | The type of those images is already distinguishable by the '.itb' extension, there is no need for an additional '-fit' string in the filenames. Remove it to behave more like other targets. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: remove 'nand-' string from image filenamesDaniel Golle2022-11-242-16/+16
| | | | | | | | | Only on the ipq40xx subtarget different filenames were used for NAND- based devices. This is unneeded, confusing and breaks downstream tools such as luci-app-attendedsysupgrade and auc. Remove the 'nand-' string from image filenames to fix that. Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Convert plasmacloud,pa2200 to DSASven Eckelmann2022-11-131-2/+1
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert plasmacloud,pa1200 to DSASven Eckelmann2022-11-131-2/+1
| | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" - can be used to power the device Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 2" port was used in the past for "WAN" functionality in OpenWrt. Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a62 to DSASven Eckelmann2022-11-121-2/+1
| | | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Tested-by: Michaël BILCOT <michael.bilcot@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Convert openmesh,a42 to DSASven Eckelmann2022-11-121-2/+1
| | | | | | | | | | | | | | | | | | | * ethernet1: - physical port label "Ethernet 1" - can be used to power the device - its mac address is printed on the device label * ethernet2: - physical port label "Ethernet 2" Both ports are not marked by there role (because the vendor firmware automatically detects roles) but the "Ethernet 1" port was used in the past for "WAN" functionality in OpenWrt. Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: D-Link DAP-2610: convert to DSAGuillaume Lefebvre2022-11-121-2/+1
| | | | | | | Reenable D-Link DAP-2610, convert it to DSA and label port to 'lan', as shown on the case Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Guillaume Lefebvre <guillaume@zelig.ch>
* ipq40xx: add support for GL.iNet GL-A1300Weiping Yang2022-11-091-0/+14
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | Specifications: SOC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB FLASH1: 4 MiB NOR FLASH2: 128 MiB NAND ETH: Qualcomm QCA8075 WLAN1: Qualcomm Atheros QCA4018 2.4GHz 802.11b/g/n 2x2 WLAN2: Qualcomm Atheros QCA4018 5G 802.11n/ac W2 2x2 USB: 1 x USB 3.0 port Button: 1 x Reset button Switch: 1 x Mode switch LED: 1 x Blue LED + 1 x White LED Install via uboot tftp or uboot web failsafe. By uboot tftp: (IPQ40xx) # tftpboot 0x84000000 openwrt-ipq40xx-generic-glinet_gl-a1300-squashfs-nand-factory.ubi (IPQ40xx) # nand erase 0 0x8000000 (IPQ40xx) # nand write 0x84000000 0 $filesize By uboot web failsafe: Push the reset button for 10 seconds util the power led flash faster, then use broswer to access http://192.168.1.1 Afterwards upgrade can use sysupgrade image. Signed-off-by: Weiping Yang <weiping.yang@gl-inet.com>
* ipq40xx: add support for MikroTik hAP ac3 LTE6 kitCsaba Sipos2022-10-301-0/+8
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the MikroTik RouterBOARD RBD53GR-5HacD2HnD (hAP ac³ LTE6 kit), an indoor dual band, dual-radio 802.11ac wireless AP with built-in Mini PCI-E LTE modem, one USB port, five 10/100/1000 Mbps Ethernet ports. See https://mikrotik.com/product/hap_ac3_lte6_kit for more info. Specifications: - SoC: Qualcomm Atheros IPQ4019 - RAM: 256 MB - Storage: 16 MB NOR - Wireless: · Built-in IPQ4019 (SoC) 802.11b/g/n 2x2:2, 3 dBi internal antennae · Built-in IPQ4019 (SoC) 802.11a/n/ac 2x2:2, 5.5 dBi internal antennae - Ethernet: Built-in IPQ4019 (SoC, QCA8075) , 5x 1000/100/10 port - 1x USB Type A port - 1x Mini PCI-E port (supporting USB) - 1x Mini PCI-E LTE modem (MikroTik R11e-LTE6, Cat.6) Installation: Make sure your unit is runnning RouterOS v6 and RouterBOOT v6 (tested on 6.49.6). 0. Export your MikroTik license key (in case you want to use the device with RouterOS later) 1. Boot the initramfs image via TFTP 2. Upload the "openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin" via SCP to the /tmp folder 3. Use sysupgrade to flash the image: sysupgrade -n /tmp/openwrt-ipq40xx-mikrotik-mikrotik_hap-ac3-lte6-kit-squashfs-sysupgrade.bin 4. Recovery to factory software is possible via Netinstall: https://help.mikrotik.com/docs/display/ROS/Netinstall Signed-off-by: Csaba Sipos <metro4@freemail.hu>
* ipq40xx: convert to DSA and enable Netgear Orbi devicesDavide Fioravanti2022-10-251-8/+4
| | | | | | | | | | Convert to DSA and enable again Netgear Orbi devices: - RBR50 - RBS50 - SRR60 - SRS60 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com>
* ipq40xx: Convert Google Wifi to DSA, reenableBrian Norris2022-10-231-2/+1
| | | | | | | | | | | | | | | | Undo parts of these: 116feb4a1cad ipq40xx: remove non-converted network configs db19efee9512 ipq40xx: disable boards not converted to DSA Reintroduce the DT paths /soc/edma@c080000/gmac{0,1}, because the stock bootloader has memorized them (instead of following aliases); then plug the MAC address back in via 05_set_iface_mac_ipq40xx.sh, since the 'local-mac-address' property is no longer in the correct node. Cc: David Bauer <mail@david-bauer.net> Cc: Robert Marko <robert.marko@sartura.hr> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
* ipq40xx: convert to DSA and enable mobipromo,cm520-79fJack Chen2022-10-231-2/+1
| | | | | | | Convert to DSA and enable the MobiPromo CM520-79F device again. Signed-off-by: Jack Chen <redchenjs@live.com> Reviewed-by: Robert Marko <robimarko@gmail.com>
* ipq40xx: convert to DSA and enable asus,rt-ac42uChen Minqiang2022-10-221-2/+1
| | | | | | | This convert board asus,rt-ac42u to DSA and re-enable it Reviewed-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Chen Minqiang <ptpt52@gmail.com>
* ipq40xx: Convert mikrotik,wap-ac to DSAMark Mentovai2022-10-191-2/+1
| | | | | | | | | | | | | | | | | | As done previously, this preserves the MAC addresses of they physical Ethernet ports. The interfaces are renamed as eth0 is in use for the native GMAC; the new interface naming matches the physical port labels. - sw-eth1 corresponds to the physical port labeled ETH1 and has the base MAC address. This port can be used to power the device. - sw-eth2 corresponds to the physical port labeled ETH2 and has a MAC address one greater than the base. As this device has 2 physical ports, they are each connected to their respective PHYs, allowing the link status to be visible to software. Since they are not marked on the case with any role (such as LAN or WAN), both are bridged to the lan network by default, although this can easily be changed if needed. Signed-off-by: Mark Mentovai <mark@mentovai.com>
* ipq40xx: convert to DSA and enable Sony NCP-HG100/CellularINAGAKI Hiroshi2022-10-091-2/+1
| | | | | | | This patch converts networking on Sony NCP-HG100/Cellular to DSA and re-enables support for the device. Signed-off-by: INAGAKI Hiroshi <musashino.open@gmail.com>
* ipq40xx: ZTE MF289F: convert to DSADirk Buchwalder2022-10-091-2/+1
| | | | | | | | | Convert ZTE MF289F device to DSA, re-order network ports to match the labels on the case and re-enable the device. Signed-off-by: Dirk Buchwalder <buchwalder@posteo.de> Reviewed-by: Robert Marko <robimarko@gmail.com> Reviewed-by: Lech Perczak <lech.perczak@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2025-02-12 21:29:37 +0000