aboutsummaryrefslogtreecommitdiffstats
path: root/target/linux/ipq40xx/image/generic.mk
Commit message (Collapse)AuthorAgeFilesLines
* ipq40xx: add RT-AC2200 alternative name to RT-AC42U/RT-ACRH17Ray Wang2022-04-101-0/+2
| | | | | | | RT-AC2200 is the same device with a different name. The OEM firmwares have the same MD5. Signed-off-by: Ray Wang <raywang777@foxmail.com> (cherry picked from commit 3204906569768cabcbedb5eaa3a11e2fcb18cd48)
* ipq40xx: add support for FRITZ!Box 7520Andre Heider2022-04-051-0/+2
| | | | | | | | | | | | | | This model, also know as "1&1 HomeServer", shares the same features as 7530. The vendor firmware has artificial software limitations: only 2 of the 4 LAN-Ports are GBit, and the USB-Host is only v2.0. With OpenWrt, USB is already working at v3.0. Signed-off-by: Andre Heider <a.heider@gmail.com> (updated commit message to reflect current state) Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit cb6f4be13703f0224fc462caaeac14e725c72986)
* ipq40xx: update E2600AC c1/c2 board张 鹏2022-03-261-2/+2
| | | | | | | | | | Modified the radio frequency hardware part of e2600ac c1/c2, need to cooperate with the modified board.bin file, the device can work normally. Signed-off-by: 张 鹏 <sd20@qxwlan.com> (cherry picked from commit bdc786e82c13547b01bd8f699d00598a974c14f6) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: disable non-building tel(co Electronics) x1proChristian Lamparter2022-03-261-0/+1
| | | | | | | | | | | Tel(co Electronics) X1 Pro is preventing ipq40xx generic from building due to the KERNEL_SIZE. Whenever bigger kernels are possible, if lzma is supported is unknown. Signed-off-by: Christian Lamparter <chunkeey@gmail.com> (cherry picked from commit 4ce52de450922dc671f08fb4551c066cfcf55bf4)
* ipq40xx: add support for Telco X1 ProNicholas Smith2022-03-191-0/+12
| | | | | | | | | | | | | | | | | | | | | | | | | | | Telco X1 Pro is a Cat12 LTE-A Pro modem router. Vendor firmware is based on a recent version of OpenWrt. Flashing is possible via CLI using sysupgrade -F -n The serial headers allow bootloader and console access Serial setting: 115200 8N1 Brief Specifications: IPQ4019 SoC 32MB flash 512MB RAM 4x gigabit LAN 1x gigabit WAN Dual-band Wave-2 wifi 2x SMA LTE antenna connectors 2x RP-SMA wifi antennas 1x USB 2.0 port 1x Reset button Serial headers installed 1x Nano SIM tray 1x Quectel EM-12G LTE-A Pro modem 1x M.2 slot attached to USB 3.0 1x internal micro SD card slot Signed-off-by: Nicholas Smith <nicholas@nbembedded.com>
* ipq40xx: add support for ZTE MF286DPawel Dembicki2022-02-051-0/+13
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | ZTE MF286D is a LTE router with four gigabit ethernet ports and integrated QMI mPCIE modem. Hardware specification: - CPU: IPQ4019 - RAM: 256MB - Flash: NAND 128MB + NOR 2MB - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11anac 2x2:2 - LTE: mPCIe cat 12 card (Modem chipset MDM9250) - LAN: 4 Gigabit Ports - USB: 1x USB2.0 (regular port). 1x USB3.0 (mpcie - used by the modem) - Serial console: X8 connector 115200 8n1 Known issues: - Many LEDs are driven by the modem. Only internal LEDs and wifi LEDs are driven by cpu. - Wifi LED is triggered by phy0tpt only - No VoIP support - LAN1/WAN port is configured as WAN - ZTE gives only one MAC per device. Use +1/+2/+3 increment for WAN and WLAN0/1 Opening the case: 1. Take of battery lid (no battery support for this model, battery cage is dummy). 2. Unscrew screw placed behind battery lid. 3. Take off back cover. It attached with multiple plastic clamps. 4. Unscrew four more screws hidden behind back case. 5. Remove front panel from blue chassis. There are more plastic clamps. 6. Unscrew two boards, which secures the PCB in the chassis. 7. Extract board from blue chassis. Console connection (X8 connector): 1. Parameters: 115200 8N1 2. Pin description: (from closest pin to X8 descriptor to farthest) - VCC (3.3V) - TX - RX - GND Install Instructions: Serial + initramfs: 1. Place OpenWrt initramfs image for the device on a TFTP in the server's root. This example uses Server IP: 192.168.1.3 2. Connect serial console (115200,8n1) to X8 connector. 3. Connect TFTP server to RJ-45 port. 4. Stop in u-Boot and run u-Boot commands: setenv serverip 192.168.1.3 setenv ipaddr 192.168.1.72 set fdt_high 0x85000000 tftp openwrt-ipq40xx-generic-zte_mf286d-initramfs-fit-zImage.itb bootm $loadaddr 5. Please make backup of original partitions, if you think about revert to stock. 6. Login via ssh or serial and remove stock partitions: ubiattach -m 9 ubirmvol /dev/ubi0 -N ubi_rootfs ubirmvol /dev/ubi0 -N ubi_rootfs_data 7. Install image via "sysupgrade -n". Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com> (cosmetic changes to the commit message) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: image: remove unused DTB_SIZE variableSungbo Eo2022-01-171-2/+0
| | | | | | It is not included in DEVICE_VARS anyways. Signed-off-by: Sungbo Eo <mans0n@gorani.run>
* ipq40xx: add RT-ACRH13 alternative name to RT-AC58UChristian Lamparter2022-01-151-0/+2
| | | | | | RT-ACRH13 is another name this device was sold as (US?). Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for ASUS RT-ACRH17/RT-AC42UJoshua Roys2022-01-151-0/+32
| | | | | | | | | | | | | | | | | | | | | SOC: IPQ4019 CPU: Quad-core ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d DRAM: 256 MB NAND: 128 MiB Macronix MX30LF1G18AC ETH: Qualcomm Atheros QCA8075 Gigabit Switch (4x LAN, 1x WAN) USB: 1x 3.0 (via Synopsys DesignWare DWC3 controller in the SoC) WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11bgn 2x2:2 WLAN2: Qualcomm Atheros QCA9984 5GHz 802.11nac 4x4:4 INPUT: 1x WPS, 1x Reset LEDS: Status, WIFI1, WIFI2, WAN (red & blue), 4x LAN This board is very similar to the RT-ACRH13/RT-AC58U. It must be flashed with an intermediary initramfs image, the jffs2 ubi volume deleted, and then finally a sysupgrade with the final image performed. Signed-off-by: Joshua Roys <roysjosh@gmail.com> (added ALT0) Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: unbreak EZVIZ CS-W3-WD1200G EUP on 5.10Christian Lamparter2021-12-041-1/+4
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | with current images, the device is no longer booting. It gets stuck in the bootloader with "Config not available" and drops to the uboot shell. |flash_type: 0 |Hit any key to stop autoboot: 0 |SF: Detected MX25L12805D with page size 4 KiB, total 16 MiB |Config not availabale |(IPQ40xx) # This is because the default bootcmd "bootipq" will only read the first four MiB of the kernel image. With 5.10 the gzip'd kernel is slightly larger. So the part of the FIT image which had the configuration is cut off. Hence it can't find it. To update the bootcmd, you have to attach the serial console again and enter the following commands into the boot prompt: # setenv bootcmd "sf probe; sf read 84000000 180000 600000; bootm" # saveenv # run bootcmd This will allow booting kernels with up to six MiB. This also allows us to drop the DEVICE_DTS_CONFIG hack we had to use. Note: uboot doesn't support LZMA. It fails with: "Unimplemented compression type 3" Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for GL.iNet GL-B2200TruongSinh Tran-Nguyen2021-12-021-0/+28
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds supports for the GL-B2200 router. Specifications: - SOC: Qualcomm IPQ4019 ARM Quad-Core - RAM: 512 MiB - Flash: 16 MiB NOR - SPI0 - EMMC: 8GB EMMC - ETH: Qualcomm QCA8075 - WLAN1: Qualcomm Atheros QCA4019 2.4GHz 802.11b/g/n 2x2 - WLAN2: Qualcomm Atheros QCA4019 5GHz 802.11n/ac W2 2x2 - WLAN3: Qualcomm Atheros QCA9886 5GHz 802.11n/ac W2 2x2 - INPUT: Reset, WPS - LED: Power, Internet - UART1: On board pin header near to LED (3.3V, TX, RX, GND), 3.3V without pin - 115200 8N1 - UART2: On board with BLE module - SPI1: On board socket for Zigbee module Update firmware instructions: Please update the firmware via U-Boot web UI (by default at 192.168.1.1, following instructions found at https://docs.gl-inet.com/en/3/troubleshooting/debrick/). Normal sysupgrade, either via CLI or LuCI, is not possible from stock firmware. Please do use the *gl-b2200-squashfs-emmc.img file, gunzipping the produced *gl-b2200-squashfs-emmc.img.gz one first. What's working: - WiFi 2G, 5G - WPA2/WPA3 Not tested: - Bluetooth LE/Zigbee Credits goes to the original authors of this patch. V1->V2: - updates *arm-boot-add-dts-files.patch correctly (sorry, my mistake) - add uboot-envtools support V2->V3: - Li Zhang updated official patch to fix wrong MAC address on wlan0 (PCI) interface V3->V4: - wire up sysupgrade Signed-off-by: Li Zhang <li.zhang@gl-inet.com> [fix tab and trailing space, document what's working and what's not] Signed-off-by: TruongSinh Tran-Nguyen <i@truongsinh.pro> [rebase on top of master, address remaining comments] Signed-off-by: Enrico Mioso <mrkiko.rs@gmail.com> [remove redundant check in platform.sh] Signed-off-by: Daniel Golle <daniel@makrotopia.org>
* ipq40xx: Add support for Teltonika RUTX10Felix Matouschek2021-11-281-0/+27
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This patch adds support for the Teltonika RUTX10. This device is an industrial DIN-rail router with 4 ethernet ports, 2.4G/5G dualband WiFi, Bluetooth, a USB 2.0 port and two GPIOs. The RUTX series devices are very similiar so common parts of the DTS are kept in a DTSI file. They are based on the QCA AP-DK01.1-C1 dev board. See https://teltonika-networks.com/product/rutx10 for more info. Hardware: SoC: Qualcomm IPQ4018 RAM: 256MB DDR3 SPI Flash 1: XTX XT25F128B (16MB, NOR) SPI Flash 2: XTX XT26G02AWS (256MB, NAND) Ethernet: Built-in IPQ4018 (SoC, QCA8075), 4x 10/100/1000 ports WiFi 1: Qualcomm QCA4019 IEEE 802.11b/g/n Wifi 2: Qualcomm QCA4019 IEEE 802.11a/n/ac USB Hub: Genesys Logic GL852GT Bluetooth: Qualcomm CSR8510 (A10U) LED/GPIO controller: STM32F030 with custom firmware Buttons: Reset button Leds: Power (green, cannot be controlled) WiFi 2.4G activity (green) WiFi 5G activity (green) MACs Details verified with the stock firmware: eth0: Partition 0:CONFIG Offset: 0x0 eth1: = eth0 + 1 radio0 (2.4 GHz): = eth0 + 2 radio1 (5.0 GHz): = eth0 + 3 Label MAC address is from eth0. The LED/GPIO controller needs a separate kernel driver to function. The driver was extracted from the Teltonika GPL sources and can be found at following feed: https://github.com/0xFelix/teltonika-rutx-openwrt USB detection of the bluetooth interface is sometimes a bit flaky. When not detected power cycle the device. When the bluetooth interface was detected properly it can be used with bluez / bluetoothctl. Flash instructions via stock web interface (sysupgrade based): 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted 5. Open stock web interface at http://192.168.1.1 6. Set some password so the web interface is happy 7. Go to firmware upgrade settings 8. Choose openwrt-ipq40xx-generic-teltonika_rutx10-squashfs-nand-factory.ubi 9. Set 'Keep settings' to off 10. Click update, when warned that it is not a signed image proceed Return to stock firmware: 1. Set PC to fixed ip address 192.168.1.100 2. Push reset button and power on the device 3. Open u-boot HTTP recovery at http://192.168.1.1 4. Upload latest stock firmware and wait until the device is rebooted Note: The DTS expects OpenWrt to be running from the second rootfs partition. u-boot on these devices hot-patches the DTS so running from the first rootfs partition should also be possible. If you want to be save follow the instructions above. u-boot HTTP recovery restores the device so that when flashing OpenWrt from stock firmware it is flashed to the second rootfs partition and the DTS matches. Signed-off-by: Felix Matouschek <felix@matouschek.org>
* ipq40xx: reenable Zyxel NBG6617 by defaultChristian Lamparter2021-11-141-1/+0
| | | | | | | | | The Zyxel NBG6617 already uses lzma to compress the kernel. A local build with every module enabled (either as =Y or =M) ended produced a 3058 KiB kernel (the kernel partition is 4MiB). It booted just fine, let's reenable the device. Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: add support for P&W R619AC (aka G-DOCK 2.0)Richard Yu2021-11-141-0/+26
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | P&W R619AC is a IPQ4019 Dual-Band AC1200 router. It is made by P&W (p2w-tech.com) known as P&W R619AC but marketed and sold more popularly as G-DOCK 2.0. Specification: * SOC: Qualcomm Atheros IPQ4019 (717 MHz) * RAM: 512 MiB * Flash: 16 MiB (NOR) + 128 MiB (NAND) * Ethernet: 5 x 10/100/1000 (4 x LAN, 1 x WAN) * Wireless: - 2.4 GHz b/g/n Qualcomm Atheros IPQ4019 - 5 GHz a/n/ac Qualcomm Atheros IPQ4019 * USB: 1 x USB 3.0 * LED: 4 x LAN, 1 x WAN, 2 x WiFi, 1 x Power (All Blue LED) * Input: 1 x reset * 1 x MicroSD card slot * Serial console: 115200bps, pinheader J2 on PCB * Power: DC 12V 2A * 1 x Unpopulated mPCIe Slot (see below how to connect it) * 1 x Unpopulated Sim Card Slot Installation: 1. Access to tty console via UART serial 2. Enter failsafe mode and mount rootfs <https://openwrt.org/docs/guide-user/troubleshooting/failsafe_and_factory_reset> 3. Edit inittab to enable shell on tty console `sed -i 's/#ttyM/ttyM/' /etc/inittab` 4. Reboot and upload `-nand-factory.bin` to the router (using wget) 5. Use `sysupgrade` command to install Another installation method is to hijack the upgrade server domain of stock firmware, because it's using insecure http. This commit is based on @LGA1150(at GitHub)'s work <https://github.com/LGA1150/openwrt/commit/a4932c8d5a275d1fb4297bd20ec03f9270a45d1c> With some changes: 1. Added `qpic_bam` node in dts. I don't know much about this, but I observed other dtses have this node. 2. Removed `ldo` node under `sd_0_pinmux`, because `ldo` cause SD card not working. This fix is from <https://github.com/coolsnowwolf/lede/commit/51143b4c7571f717afe071db60bbb4db1532cbf2> 3. Removed the 32MB NOR variant. 4. Removed `cd-gpios` in `sdhci` node, because it's reported that it makes wlan2g led light up. 5. Added ethphy led config in dts. 6. Changed nand partition label from `rootfs` to `ubi`. About the 128MiB variant: The stock bootloader sets size of nand to 64MiB. But most of this devices have 128MiB nand. If you want to use all 128MiB, you need to modify the `MIBIB` data of bootloader. More details can be found on github: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-818770060> For instructions on how to flash the MIBIB partition from u-boot console: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-819138232> About the Mini PCIe slot: (from "ygleg") "The REFCLK signals on the Mini PCIe slot is not connected on this board out of the box. If you want to use the Mini PCIe slot on the board, you need to (preferably) solder two 0402 resistors: R436 (REFCLK+) and R444 (REFCLK-)..." This and much more information is provoided in the github comment: <https://github.com/openwrt/openwrt/pull/3691#issuecomment-968054670> Signed-off-by: Richard Yu <yurichard3839@gmail.com> Signed-off-by: DENG Qingfang <dqfext@gmail.com> [Added comment about MIBIB+128 MiB variant. Added commit message section about pcie slot. Renamed gpio-leds' subnodes and added color, function+enum properties.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: use zImage for Cell-C RTL30VWPawel Dembicki2021-11-061-4/+3
| | | | | | | | | | After switch to 5.10 kernel, kernel size was too high. This patch switches Cell-C RTL30VW from uImage to zImage build. Lzma uImage wrap is required for factory booting and it must left untouched. Signed-off-by: Pawel Dembicki <paweldembicki@gmail.com>
* ipq40xx: disable some devices due to kernel sizeRobert Marko2021-11-031-0/+9
| | | | | | | | | | Disable some of the ipq40xx devices due to their kernel size limitations. These devices fail to build with kernel 5.10 and full buildbot config. Signed-off-by: Robert Marko <robert.marko@sartura.hr> [keep gl-b1300/gl-s1300 enabled, extend commit message] Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de>
* ipq40xx: add support for Netgear SRR60/SRS60 and RBR50/RBS50Davide Fioravanti2021-11-011-0/+58
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | The Netgear SRS60 and SRR60 (sold together as SRK60) are two almost identical AC3000 routers. The SRR60 has one port labeled as wan while the SRS60 not. The RBR50 and RBS50 (sold together as RBK50) have a different external shape but they have an USB 2.0 port on the back. This patch has been tested only on SRS60 and RBR50, but should work on SRR60 and RBS50. Hardware -------- SoC: Qualcomm IPQ4019 (717 MHz, 4 cores 4 threads) RAM: 512MB DDR3 FLASH: 4GB EMMC ETH: - 3x 10/100/1000 Mbps Ethernet - 1x 10/100/1000 Mbps Ethernet (WAN) WIFI: - 2.4GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x IPQ4019 (2x2:2) - 5GHz: 1x QCA9984 (4x4:4) - 6 internal antennas BTN: - 1x Reset button - 1x Sync button - 1x ON/OFF button LEDS: - 8 leds controlled by TLC59208F (they can be switched on/off independendently but the color can by changed by GPIOs) - 1x Red led (Power) - 1x Green led (Power) UART: - 115200-8-N-1 Everything works correctly. Installation ------------ These routers have a dual partition system. However this firmware works only on boot partition 1 and the OEM web interface will always flash on the partition currently not booted. The following steps will use the SRS60 firmware, but you have to chose the right firmware for your router. There are 2 ways to install Openwrt the first time: 1) Using NMRPflash 1. Download nmrpflash (https://github.com/jclehner/nmrpflash) 2. Put the openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img file in the same folder of the nmrpflash executable 3. Connect your pc to the router using the port near the power button. 4. Run "nmrpflash -i XXX -f openwrt-ipq40xx-generic-netgear_srs60-squashfs-factory.img". Replace XXX with your network interface (can be identified by running "nmrpflash -L") 5. Power on the router and wait for the flash to complete. After about a minute the router should boot directly to Openwrt. If nothing happens try to reboot the router. If you have problems flashing try to set "10.164.183.253" as your computer IP address 2) Without NMRPflash The OEM web interface will always flash on the partition currently not booted, so to flash OpenWrt for the first time you have to switch to boot partition 2 and then flash the factory image directly from the OEM web interface. To switch on partition 2 you have to enable telnet first: 1. Go to http://192.168.1.250/debug.htm and check "Enable Telnet". 2. Connect through telent ("telnet 192.168.1.250") and login using admin/password. To read the current boot_part: artmtd -r boot_part To write the new boot_part: artmtd -w boot_part 02 Then reboot the router and then check again the current booted partition Now that you are on boot partition 2 you can flash the factory Openwrt image directly from the OEM web interface. Restore OEM Firmware -------------------- 1. Download the stock firmware from official netgear support. 2. Follow the nmrpflash procedure like above, using the official Netgear firmware (for example SRS60-V2.2.1.210.img) nmrpflash -i XXX -f SRS60-V2.2.1.210.img Notes ----- 1) You can check and edit the boot partition in the Uboot shell using the UART connection. "boot_partition_show" shows the current boot partition "boot_partition_set 1" sets the current boot partition to 1 2) Router mac addresses: LAN XX:XX:XX:XX:XX:69 WAN XX:XX:XX:XX:XX:6a WIFI 2G XX:XX:XX:XX:XX:69 WIFI 5G XX:XX:XX:XX:XX:6b WIFI 5G (2nd) XX:XX:XX:XX:XX:6c LABEL XX:XX:XX:XX:XX:69 Signed-off-by: Davide Fioravanti <pantanastyle@gmail.com> Signed-off-by: Robert Marko <robimarko@gmail.com> [added 5.10 changes for 901-arm-boot-add-dts-files.patch, moved sysupgrade mmc.sh to here and renamed it, various dtsi changes] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: use zImage for GL.iNet GL-B1300, GL-S1300 to shrink below 4096kSzabolcs Hubai2021-10-101-2/+2
| | | | | | | | | | | | | | | | | | | | | | | | In the "ipq40xx: switch to Kernel 5.10" discussion at GitHub, Adrian noted [0] that these GL.iNet Conexa series devices, GL-B1300 and GL-S1300 failed their image generation [1] as their gzipped uImage kernel went above 4096k. While notifying the vendor about this problem [2], I tested all U-Boot releases from GL.iNet: - they really fail to boot kernel above 4096k - they don't support lzma: "Unimplemented compression type 3" - but they boot zImage Using zImage (xz compression) the kernel is 2909k which is more than a megabyte away from the KERNEL_SIZE := 4096k limit. The gzip compressed version would be 4116k. [0]: https://github.com/openwrt/openwrt/pull/4620#issuecomment-932765776 [1]: commit 7b1fa276f5a2 ("ipq40xx: add testing support for kernel 5.10") [2]: https://forum.gl-inet.com/t/ipq40xx-kernel-size-and-u-boot-v5-10-is-too-big-for-4-mb/17619 Signed-off-by: Szabolcs Hubai <szab.hu@gmail.com>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA2200Sven Eckelmann2021-09-121-1/+1
| | | | | | | | | | | The board data file for the Plasma Cloud PA2200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: 4871fd2616ac ("ipq40xx: add support for Plasma Cloud PA2200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Fix board-2.bin package name for Plasma Cloud PA1200Sven Eckelmann2021-09-121-1/+1
| | | | | | | | | | | The board data file for the Plasma Cloud PA1200 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. A typo in the device package name resulted in a not correctly selected package for the device specific board-2.bin. The wifi driver has therefore loaded the wrong calibration information into the wifi chip. Fixes: ea5bb6bbfee0 ("ipq40xx: add support for Plasma Cloud PA1200") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMR3500Sven Eckelmann2021-09-121-0/+1
| | | | | | | | | The board data file for the EnGenius EMR3500 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 3f61e5e1b97e ("ipq40xx: add support for EnGenius EMR3500") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: Select correct board-2.bin for EnGenius EMD1Sven Eckelmann2021-09-121-0/+1
| | | | | | | | | The board data file for the EnGenius EMD1 is not part of the default board-2.bin which is shipped by ath10k-board-qca4019. As result, the wrong calibration information will be loaded into the wifi chip. Fixes: 51f303597839 ("ipq40xx: add support for EnGenius EMD1") Signed-off-by: Sven Eckelmann <sven@narfation.org>
* ipq40xx: fix Edgecore ECW5211 bootStijn Tintel2021-08-181-0/+1
| | | | | | | The bootloader will look for a configuration section named ap.dk01.1-c2 in the FIT image. If this doesn't exist, the device won't boot. Signed-off-by: Stijn Tintel <stijn@linux-ipv6.be>
* treewide: call check-size before append-metadataAdrian Schmutzler2021-07-101-4/+4
| | | | | | | | | | sysupgrade metadata is not flashed to the device, so check-size should be called _before_ adding metadata to the image. While at it, do some obvious wrapping improvements. Signed-off-by: Adrian Schmutzler <freifunk@adrianschmutzler.de> Acked-by: Paul Spooren <mail@aparcar.org>
* ipq40xx: add uboot-envtools to default packagesTomasz Maciej Nowak2021-06-061-16/+12
| | | | | | | | | | | | | | | | | | | When support for Luma WRTQ-329ACN was added, the instructions for flashing this device include using tools from uboot-envtools package. Unfortunately the OpenWrt buildroot system omits packages from DEVICE_PACKAGES when CONFIG_TARGET_MULTI_PROFILE, CONFIG_TARGET_PER_DEVICE_ROOTFS, CONFIG_TARGET_ALL_PROFILES are set. In result the official images are without tools mentioned in the instruction. The workoround for the fashing would be installing uboot-envtools when booted with initramfs image, but not always the access to internet is available. The other method would be to issue the necesary command in U-Boot environment but some serial terminals default configuration don't work well with pasting lines longer than 80 chars. Therefore add uboot-envtools to default packages, which adds really small flash footprint to rootfs, where increased size usually is not an issue. Signed-off-by: Tomasz Maciej Nowak <tmn505@gmail.com>
* ipq40xx: add netgear wac510 supportRobert Marko2021-06-051-0/+25
| | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | | This adds support for the Netgear WAC510 Insight Managed Smart Cloud Wireless Access Point, an indoor dual-band, dual-radio 802.11ac business-class wireless AP with integrated omnidirectional antennae and two 10/100/1000 Mbps Ethernet ports. For more information see: <https://www.netgear.com/business/wifi/access-points/wac510> Specifications: SoC: Qualcomm IPQ4018 (DAKOTA) ARM Quad-Core RAM: 256 MiB Flash1: 2 MiB Winbond W25Q16JV SPI-NOR Flash2: 128 MiB Winbond W25N01GVZEIG SPI-NAND Ethernet: Built-in IPQ4018 (SoC, QCA8072 PHY), 2x 1000/100/10 port, WAN port active IEEE 802.3af/at PoE in Wireless1: Built-in IPQ4018 (SoC) 802.11b/g/n 2x2:2, 3 dBi antennae Wireless2: Built-in IPQ4018 (SoC) 802.11a/n/ac 2x2:2, 4 dBi antennae Input: (Optional) Barrel 12 V 2.5 A Power, Reset button SW1 LEDs: Power, Insight, WAN PoE, LAN, 2.4G WLAN, 5G WLAN Serial: Header J2 1 - 3.3 Volt (Do NOT connect!) 2 - TX 3 - RX 4 - Ground WARNING: The serial port needs a TTL/RS-232 3.3 volt level converter! The Serial settings are 115200-8-N-1. Installation via Stock Web Interface: BTW: The default factory console/web interface login user/password are admin/password. In the web interface navigating to Management - Maintenance - Upgrade - 'Firmware Upgrade' will show you what is currently installed e.g.: Manage Firmware Current Firmware Version: V5.0.10.2 Backup Firmware Version: V1.2.5.11 Under 'Upgrade Options' choose Local (alternatively SFTP would be available) then click/select 'Browse File' on the right side, choose openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.tar and hit the Upgrade button below. After a minute or two your browser should indicate completion printing 'Firmware update complete.' and 'Rebooting AP...'. Note that OpenWrt will use the WAN PoE port as actual WAN port defaulting to DHCP client but NOT allowing LuCI access, use LAN port defaulting to 192.168.1.1/24 to access LuCI. Installation via TFTP Requiring Serial U-Boot Access: Connect to the device's serial port and hit any key to stop autoboot. Upload and boot the initramfs based OpenWrt image as follows: (IPQ40xx) # setenv serverip 192.168.1.1 (IPQ40xx) # setenv ipaddr 192.168.1.2 (IPQ40xx) # tftpboot openwrt-ipq40xx-generic-netgear_wac510-initramfs-fit-uImage.itb (IPQ40xx) # bootm Note: This only runs OpenWrt from RAM and has not installed anything to flash as of yet. One may permanently install OpenWrt as follows: Check the MTD device number of the active partition: root@OpenWrt:/# dmesg | grep 'set to be root filesystem' [ 1.010084] mtd: device 9 (rootfs) set to be root filesystem Upload the factory image ending with .ubi to /tmp (e.g. using scp or tftp). Then flash the image as follows (substituting the 9 in mtd9 below with whatever number reported above): root@OpenWrt:/# ubiformat /dev/mtd9 -f /tmp/openwrt-ipq40xx-generic-netgear_wac510-squashfs-nand-factory.ubi And reboot. Dual Image Configuration: The default U-Boot boot command bootipq uses the U-Boot environment variables primary/secondary to decide which image to boot. E.g. primary=0, secondary=3800000 uses rootfs while primary=3800000, secondary=0 uses rootfs_1. Switching their values changes the active partition. E.g. from within U-Boot: (IPQ40xx) # setenv primary 0 (IPQ40xx) # setenv secondary 3800000 (IPQ40xx) # saveenv Or from a OpenWrt userspace serial/SSH console: fw_setenv primary 0 fw_setenv secondary 3800000 Note that if you install two copies of OpenWrt then each will have its independent configuration not like when switching partitions on the stock firmware. BTW: The kernel log shows which boot partition is active: [ 2.439050] ubi0: attached mtd9 (name "rootfs", size 56 MiB) vs. [ 2.978785] ubi0: attached mtd10 (name "rootfs_1", size 56 MiB) Note: After 3 failed boot attempts it automatically switches partition. Signed-off-by: Robert Marko <robimarko@gmail.com> Signed-off-by: Marcel Ziswiler <marcel@ziswiler.com> [squashed netgear-tar commit into main and rename netgear-tar for now, until it is made generic.] Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
* ipq40xx: fix boards being shown twiceRobert Marko2021-01-211-2/+0
| | | | | | | | | | | | | | | | Since generic images have been split to their own Makefile boards are showing up twice in menuconfig as $(eval $(call BuildImage)) was not dropped from the new generic.mk. Hence $(eval $(call BuildImage)) was being called twice. So, lets simply drop it from generic.mk. Fixes: 378c7ff28210 ("ipq40xx: split generic images into own file") Signed-off-by: Robert Marko <robert.marko@sartura.hr>
* ipq40xx: split generic images into own fileAlexander Couzens2021-01-171-0/+809
In preparation of the new mikrotik subtarget split the generic images into generic.mk Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
generated by cgit v1.2.3 (git 2.25.1) at 2024-07-13 03:08:00 +0000